PE23020 · Loss Of Motive Power Due To Broken Crankshaft With No Ability To Restart.
Opened Nov 15, 2023 · Closed Jun 27, 2025
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling:engine:diesel
On November 15, 2023, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE23020 to investigate allegations of loss of motive power in model year (MY) 2016 through 2019 Nissan Titan XD trucks equipped with 5.0L Cummins diesel engines. The complaints allege the condition was due to a failure of the engine crankshaft. The purpose of the investigation was to understand the scope, frequency, and safety related consequence of the alleged defect. During the investigation, it was found that the subject vehicles can experience a loss of motive power due to a failure of the crankshaft main bearings which can lead to a fractured crankshaft. This resulted in a loss of motive power and an inability to restart. An analysis of all complaint sources shows many vehicles exhibit knocking, vibration, malfunction indicator lamp (MIL) warnings, and/or poor engine performance prior to a total failure. Some consumers report driving their truck in for repairs only to be diagnosed with a failed crankshaft. ODI has not identified any injuries or fires attributable to this failure. ODI is aware of one complaint alleging a non-injury crash involving a curb strike. ODI is also aware of complaints of overheating starter motors and melted starter motor wiring occurring after prolonged attempts to start engines that have suffered a broken crankshaft. In its response to ODI's January 26, 2024 information request letter, Nissan provided information detailing several material and process changes involved in the production of the subject vehicle’s engine.These changes appear to coincide with incremental improvements in failure rates but there is no indication that a single factor was the primary cause of the failures. Analysis of ODI consumer complaints and manufacturer provided data found that failure rates decreased progressively for each model year. Review of failure mileage found that 50% of the failures occurred by 60,000 miles with a significant decrease in failures after 80,000 miles. Assuming average yearly mileage driven, the newest model year trucks (2019) would be near or past peak failure mileage. Given the low failure rate, the observable warnings available to the driver, and much of the fleet being past peak failure mileage, ODI is closing this Preliminary Evaluation with no further action. The closing of the investigation does not constitute a finding by NHTSA that a defect does not exist, and NHTSA will take further action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:diesel
On November 15, 2023, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE23020 to investigate allegations of loss of motive power in model year (MY) 2016 through 2019 Nissan Titan XD trucks equipped with 5.0L Cummins diesel engines. The complaints allege the condition was due to a failure of the engine crankshaft. The purpose of the investigation was to understand the scope, frequency, and safety related consequence of the alleged defect. During the investigation, it was found that the subject vehicles can experience a loss of motive power due to a failure of the crankshaft main bearings which can lead to a fractured crankshaft. This resulted in a loss of motive power and an inability to restart. An analysis of all complaint sources shows many vehicles exhibit knocking, vibration, malfunction indicator lamp (MIL) warnings, and/or poor engine performance prior to a total failure. Some consumers report driving their truck in for repairs only to be diagnosed with a failed crankshaft. ODI has not identified any injuries or fires attributable to this failure. ODI is aware of one complaint alleging a non-injury crash involving a curb strike. ODI is also aware of complaints of overheating starter motors and melted starter motor wiring occurring after prolonged attempts to start engines that have suffered a broken crankshaft. In its response to ODI's January 26, 2024 information request letter, Nissan provided information detailing several material and process changes involved in the production of the subject vehicle’s engine.These changes appear to coincide with incremental improvements in failure rates but there is no indication that a single factor was the primary cause of the failures. Analysis of ODI consumer complaints and manufacturer provided data found that failure rates decreased progressively for each model year. Review of failure mileage found that 50% of the failures occurred by 60,000 miles with a significant decrease in failures after 80,000 miles. Assuming average yearly mileage driven, the newest model year trucks (2019) would be near or past peak failure mileage. Given the low failure rate, the observable warnings available to the driver, and much of the fleet being past peak failure mileage, ODI is closing this Preliminary Evaluation with no further action. The closing of the investigation does not constitute a finding by NHTSA that a defect does not exist, and NHTSA will take further action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On November 15, 2023, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE23020 to investigate allegations of loss of motive power in model year (MY) 2016 through 2019 Nissan Titan XD trucks equipped with 5.0L Cummins diesel engines. The complaints allege the condition was due to a failure of the engine crankshaft. The purpose of the investigation was to understand the scope, frequency, and safety related consequence of the alleged defect. During the investigation, it was found that the subject vehicles can experience a loss of motive power due to a failure of the crankshaft main bearings which can lead to a fractured crankshaft. This resulted in a loss of motive power and an inability to restart. An analysis of all complaint sources shows many vehicles exhibit knocking, vibration, malfunction indicator lamp (MIL) warnings, and/or poor engine performance prior to a total failure. Some consumers report driving their truck in for repairs only to be diagnosed with a failed crankshaft. ODI has not identified any injuries or fires attributable to this failure. ODI is aware of one complaint alleging a non-injury crash involving a curb strike. ODI is also aware of complaints of overheating starter motors and melted starter motor wiring occurring after prolonged attempts to start engines that have suffered a broken crankshaft. In its response to ODI's January 26, 2024 information request letter, Nissan provided information detailing several material and process changes involved in the production of the subject vehicle’s engine.These changes appear to coincide with incremental improvements in failure rates but there is no indication that a single factor was the primary cause of the failures. Analysis of ODI consumer complaints and manufacturer provided data found that failure rates decreased progressively for each model year. Review of failure mileage found that 50% of the failures occurred by 60,000 miles with a significant decrease in failures after 80,000 miles. Assuming average yearly mileage driven, the newest model year trucks (2019) would be near or past peak failure mileage. Given the low failure rate, the observable warnings available to the driver, and much of the fleet being past peak failure mileage, ODI is closing this Preliminary Evaluation with no further action. The closing of the investigation does not constitute a finding by NHTSA that a defect does not exist, and NHTSA will take further action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration