EVERYTHING ON THE BOTTOMS OF THE SUV THAT I HAVE SEEN INCLUDING MINE ARE ALL RUSTING ON THE BOTTOMS. INCLUDING BRAND NEW ONES THAT ARE STILL ON THE LOT. NISSAN SAYS IT'S THE SALT IN THE ROADS BUT I DON'T FIND THAT THE CASE. NEEDS TO BE INVESTIGATED BECAUSE MINE KEEPS GETTING WORSE AND I FEEL IT SHOULD BE REPLACED. HAD 2006 AND I…
Read full complaint
EVERYTHING ON THE BOTTOMS OF THE SUV THAT I HAVE SEEN INCLUDING MINE ARE ALL RUSTING ON THE BOTTOMS. INCLUDING BRAND NEW ONES THAT ARE STILL ON THE LOT. NISSAN SAYS IT'S THE SALT IN THE ROADS BUT I DON'T FIND THAT THE CASE. NEEDS TO BE INVESTIGATED BECAUSE MINE KEEPS GETTING WORSE AND I FEEL IT SHOULD BE REPLACED. HAD 2006 AND IT WAS SAME WAY. *TR
NHTSA ODI #10620671
68,000 miles · May 5, 2014
Latches/locks/linkagesStructure
THE DOOR LOCK ACTUATOR STOPS WORKING TRAPPING THE RIDER IN THE CAR.
NHTSA ODI #10586610
76,000 miles · May 4, 2014
Structure
2009 NISSAN MURANO, FRONT PASSENGER DOOR, WILL NOT OPEN WITH EITHER THE OUTSIDE OR INSIDE DOOR HANDLE. THE DOOR IS LOCKED CLOSED. IN THE CASE OF NORMAL OPERATION OR IN AN EMERGENCY THE DOOR CANNOT OPEN. IT APPEARS THAT NISSAN IS VERY WELL AWARE OF THIS ISSUE FROM THE NUMBER OF COMPLAINTS ON FORUMS AND THE INTERNET. THERE…
Read full complaint
2009 NISSAN MURANO, FRONT PASSENGER DOOR, WILL NOT OPEN WITH EITHER THE OUTSIDE OR INSIDE DOOR HANDLE. THE DOOR IS LOCKED CLOSED. IN THE CASE OF NORMAL OPERATION OR IN AN EMERGENCY THE DOOR CANNOT OPEN. IT APPEARS THAT NISSAN IS VERY WELL AWARE OF THIS ISSUE FROM THE NUMBER OF COMPLAINTS ON FORUMS AND THE INTERNET. THERE ARE SEVERAL YEARS IN WHICH THE VEHICLES THAT HAVE THIS ISSUE. THERE IS NO CORRECTIVE ACTION BEING TAKEN BY NISSAN, NOR IS THERE ANY NOTIFICATION FOR REPAIR, REPLACEMENT, RECALL, ETC. I WOULD FIND IT HARD TO BELIEVE THAT THIS IS NOT CONSIDERED A SAFETY ISSUE. I HOPE THAT NHTSA LOOKS INTO HAVING NISSAN PUT IN A CORRECTIVE ACTION. THIS ISSUE OF DOOR HANDLES NOT OPERATING ARE ON SEVERAL YEARS' MODELS AND HAVE BEEN AN ONGOING ISSUE TO THE VEHICLE OWNERS. *TR
NHTSA ODI #10586469
106,500 miles · Apr 4, 2014
Structure
FRONT LEFT DRIVER SIDE DOOR CANNOT BE OPENED FROM THE INSIDE OR OUTSIDE TRAPPING ME, THE DRIVER, INSIDE THE VEHICLE. A SIMILAR PROBLEM OCCURRED LAST YEAR, 04/09/2013 @ 91,393 MILES, WITH THE FRONT PASSENGER DOOR. AGAIN, TRAPPING THE PASSENGER INSIDE THE VEHICLE. THESE FAULTY MANUFACTURED PARTS NEEDED TO BE REPLACED: 80501-1AA…
Read full complaint
FRONT LEFT DRIVER SIDE DOOR CANNOT BE OPENED FROM THE INSIDE OR OUTSIDE TRAPPING ME, THE DRIVER, INSIDE THE VEHICLE. A SIMILAR PROBLEM OCCURRED LAST YEAR, 04/09/2013 @ 91,393 MILES, WITH THE FRONT PASSENGER DOOR. AGAIN, TRAPPING THE PASSENGER INSIDE THE VEHICLE. THESE FAULTY MANUFACTURED PARTS NEEDED TO BE REPLACED: 80501-1AA0A & 80500-1AA0A (LOCK & REMOTE C).
NHTSA ODI #10577684
84,000 miles · Mar 15, 2014
Equipment Adaptive/mobilityStructureCrash
I HAVE NEVER OWNED A VEHICLE WITH THIS MANY BLIND SPOTS! I HAVE HAD SO MANY "CLOSE CALLS" AND IT FINALLY CAUGHT UP TO ME. I WAS BACKING OUT OF A PARKING PLACE AND BACKED INTO A CAR. THE CAR WAS DOUBLE PARKED BUT I LOOKED IN MY MIRRORS AND OVER MY SHOULDER AND NEVER SEEN THE CAR. THIS BEING SAID, I WAS ALREADY SCARED OF MY MURANO…
Read full complaint
I HAVE NEVER OWNED A VEHICLE WITH THIS MANY BLIND SPOTS! I HAVE HAD SO MANY "CLOSE CALLS" AND IT FINALLY CAUGHT UP TO ME. I WAS BACKING OUT OF A PARKING PLACE AND BACKED INTO A CAR. THE CAR WAS DOUBLE PARKED BUT I LOOKED IN MY MIRRORS AND OVER MY SHOULDER AND NEVER SEEN THE CAR. THIS BEING SAID, I WAS ALREADY SCARED OF MY MURANO PRIOR TO THIS BECAUSE OF THE SIDE BLIND SPOTS. I HAVE ALMOST HIT PEDESTRIANS, CARS, AND BICYCLISTS CROSSING THE STREET ON NUMEROUS OCCASIONS. THE VEHICLE WHERE THE SIDE MIRRORS ARE IS WAY TO BIG, ALONG WITH THE MIRRORS, THERE IS A HUGE BLIND SPOT. I HAVE BEEN VERY CAUTIOUS WHEN TURNING BECAUSE OF THIS BUT NEVER REALIZED HOW THE BLIND SPOT IN THE SIDE REAR WAS I TILL I HIT THAT CAR. THE REAR BACK WINDOWS ARE SMALL BUT THE ISSUES IS THE WINDOWS ARE TO HIGH AND THE BODY IS AT AN UPWARD SLANT LEAVING NO VIEW WHEN LOOKING OVER YOUR SHOULDER. THIS GIVES PEOPLE A SENSE THAT THEY CAN SEE BUT YOU CAN NOT SEE A CAR SITTING AT YOUR REAR QUARTER PANEL. WITH ALL OF THE BLIND SPOTS I AM AFRAID I WILL RUN OVER A PEDESTRIAN WALKING ACROSS THE STREET AS I AM TURNING AND NOW AFRAID I WILL BACK INTO SOMETHING OR SOMEONE DUE TO THE SIDE REAR BLIND SPOTS. *TR
NHTSA ODI #10572541
72,652 miles · Feb 18, 2013
Electrical SystemStructure
LIFTGATE WILL NOT OPEN FROM OUTSIDE, REGARDLESS OF METHOD USED. THE DRIVER'S BUTTON, THE FOB, AND THE BUTTON ON THE LIFTGATE DO NOTHING. IN THE EVENT OF AN EMERGENCY, THE LIFTGATE CANNOT BE USED AS A MEANS OF ENTRY OR EXIT OF THE VEHICLE. *TR
NHTSA ODI #10498544
Mileage unknown · Mar 26, 2012
Electrical SystemStructure
PASSENGER DOOR WON'T OPEN. *TR
NHTSA ODI #10452965
34,600 miles · Jul 13, 2011
EquipmentStructure
TL* THE CONTACT OWNS A 2009 NISSAN MURANO. WHILE DRIVING APPROXIMATELY 70 MPH THE CONTACT NOTICED THAT THE AIR CONDITIONER FAILED. THE VEHICLE WAS TAKEN TO THE DEALER FOR DIAGNOSTIC TESTING. THE TECHNICIANS STATED THE FRONT BUMPER ON THE VEHICLE HAD THREE SMALL HOLES WHICH ALLOWED DEBRIS INTO THE ENGINE AND DAMAGED THE CONDENSE…
Read full complaint
TL* THE CONTACT OWNS A 2009 NISSAN MURANO. WHILE DRIVING APPROXIMATELY 70 MPH THE CONTACT NOTICED THAT THE AIR CONDITIONER FAILED. THE VEHICLE WAS TAKEN TO THE DEALER FOR DIAGNOSTIC TESTING. THE TECHNICIANS STATED THE FRONT BUMPER ON THE VEHICLE HAD THREE SMALL HOLES WHICH ALLOWED DEBRIS INTO THE ENGINE AND DAMAGED THE CONDENSER. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 34,600.
NHTSA ODI #10412108
1,250 miles · May 21, 2008
Structure
THE SUNROOF IN MY 2009 NISSAN MURANO LE STOPPED WORKING (WOULDN'T OPEN) JUST 3 WEEKS AFTER TAKING DELIVERY. NEITHER THE DEALER OR NISSAN CUSTOMER CARE COULD TELL WHEN A REPLACEMENT PART WILL BECOME AVAILABLE. IT IS IN BACK ORDER AND FOR THE PAST 2.5 WEEKS THE STATUS OF THE INFORMATION IS THE SAME I.E. NO PROJECTED DATE OF GETTIN…
Read full complaint
THE SUNROOF IN MY 2009 NISSAN MURANO LE STOPPED WORKING (WOULDN'T OPEN) JUST 3 WEEKS AFTER TAKING DELIVERY. NEITHER THE DEALER OR NISSAN CUSTOMER CARE COULD TELL WHEN A REPLACEMENT PART WILL BECOME AVAILABLE. IT IS IN BACK ORDER AND FOR THE PAST 2.5 WEEKS THE STATUS OF THE INFORMATION IS THE SAME I.E. NO PROJECTED DATE OF GETTING THE PART. *TR
Nissan of North America, Inc (Nissan) is recalling certain 2009 Murano vehicles. The valves within the ABS Hydraulic Control Units (HCU) may react with brake fluids containing specific corrosion preventative additives. This reaction may cause the valves to not close properly.
Consequence & remedy
Consequence: If the valves do not properly close, additional brake pedal travel may be required to stop the vehicle, increasing the risk of a crash.
Remedy: Nissan has notified owners, and dealers will flush the brake system with DOT 4 fluid. The HCU will then be tested to detect a possible stuck valve condition. If necessary, the HCU will be replaced, free of charge. The recall began February 7, 2019. Owners may contact Nissan customer service at 1-800-867-7669.
NISSAN IS RECALLING CERTAIN MODEL YEAR 2008-2010 VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, IOWA, ILLINOIS, INDIANA, MASSACHUSETTS, MAINE, MARYLAND, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WASHINGTON D.C., WEST VIRGINIA AND WISCONSIN. THE MATERIAL IN THE NUT USED TO SECURE THE SENSOR-TRANSMITTER OF THE TIRE PRESSURE MONITORING SYSTEM (TPMS) MAY CORRODE AND POTENTIALLY CRACK IN AREAS WITH HEAVY CONCENTRATIONS OF ROAD SALT. IF THIS OCCURS, THE NUT MAY COME OUT OF THE SENSOR-TRANSMITTER AND THE TPMS LAMP WILL ILLUMINATE.
Consequence & remedy
Consequence: IF THE TPMS LAMP IS DISREGARDED AND THE VEHICLE CONTINUES TO BE DRIVEN IN THIS CONDITION, THE TIRE WILL QUICKLY LOSE AIR PRESSURE AT A CONSISTENT RATE RESULTING IN A FLAT TIRE INCREASING THE RISK OF A CRASH.
Remedy: THE DEALER WILL REPLACE THE TPMS NUT WITH A NEW, MORE ROBUST NUT. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON OR BEFORE NOVEMBER 9, 2009. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261 AND INFINITI AT 1-800-662-6200.
NISSAN IS RECALLING 204,361 MY 2007-2008 ALTIMA, ALTIMA HYBRID, 350Z, 350Z ROADSTER, MY 2008 ALTIMA COUPE, ROGUE, MY 2009 MURANO, AND INFINITI MY 2007-2008 G35 SEDAN, MY 2008 G37 COUPE AND EX35 PASSENGER VEHICLES EQUIPPED WITH CONTINENTAL AUTOMOTIVE SYSTEMS' OCCUPANT CLASSIFICATION SYSTEM (OCS) CONTROL UNITS. A VARISTOR IN THE OCS CONTROL UNIT LOCATED IN THE PASSENGER SEAT CUSHION MAY HAVE BEEN MANUFACTURED OUT OF SPECIFICATION. UNDER CERTAIN CONDITIONS, THIS COULD CAUSE AN INTERRUPTION OF SIGNAL BETWEEN THE OCS AND THE AIR BAG CONTROL UNIT (ACU).
Consequence & remedy
Consequence: THIS COULD RESULT IN THE PASSENGER AIR BAG BEING SUPPRESSED WHICH COULD FAIL TO PROVIDE ADEQUATE PROTECTION IN THE EVENT OF A CRASH.
Remedy: DEALERS WILL TEST THE SIGNAL BETWEEN THE OCS AND ACU SYSTEMS USING A SPECIAL TOOL TO CHECK THAT IT IS FUNCTIONING AS DESIGNED. IF NECESSARY, THE SEAT CUSHION (CONTAINING OCS HARDWARE) WILL BE REPLACED WITH A NEW ONE MANUFACTURED TO SPECIFICATION. THE RECALL BEGAN ON NOVEMBER 4, 2008. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261 OR INFINITI AT 1-800-662-6200.
Additional source detail variants (2)
Electrical System:software
NISSAN IS RECALLING 204,361 MY 2007-2008 ALTIMA, ALTIMA HYBRID, 350Z, 350Z ROADSTER, MY 2008 ALTIMA COUPE, ROGUE, MY 2009 MURANO, AND INFINITI MY 2007-2008 G35 SEDAN, MY 2008 G37 COUPE AND EX35 PASSENGER VEHICLES EQUIPPED WITH CONTINENTAL AUTOMOTIVE SYSTEMS' OCCUPANT CLASSIFICATION SYSTEM (OCS) CONTROL UNITS. A VARISTOR IN THE OCS CONTROL UNIT LOCATED IN THE PASSENGER SEAT CUSHION MAY HAVE BEEN MANUFACTURED OUT OF SPECIFICATION. UNDER CERTAIN CONDITIONS, THIS COULD CAUSE AN INTERRUPTION OF SIGNAL BETWEEN THE OCS AND THE AIR BAG CONTROL UNIT (ACU).
Consequence: THIS COULD RESULT IN THE PASSENGER AIR BAG BEING SUPPRESSED WHICH COULD FAIL TO PROVIDE ADEQUATE PROTECTION IN THE EVENT OF A CRASH.
Remedy: DEALERS WILL TEST THE SIGNAL BETWEEN THE OCS AND ACU SYSTEMS USING A SPECIAL TOOL TO CHECK THAT IT IS FUNCTIONING AS DESIGNED. IF NECESSARY, THE SEAT CUSHION (CONTAINING OCS HARDWARE) WILL BE REPLACED WITH A NEW ONE MANUFACTURED TO SPECIFICATION. THE RECALL BEGAN ON NOVEMBER 4, 2008. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261 OR INFINITI AT 1-800-662-6200.
Air Bags
NISSAN IS RECALLING 204,361 MY 2007-2008 ALTIMA, ALTIMA HYBRID, 350Z, 350Z ROADSTER, MY 2008 ALTIMA COUPE, ROGUE, MY 2009 MURANO, AND INFINITI MY 2007-2008 G35 SEDAN, MY 2008 G37 COUPE AND EX35 PASSENGER VEHICLES EQUIPPED WITH CONTINENTAL AUTOMOTIVE SYSTEMS' OCCUPANT CLASSIFICATION SYSTEM (OCS) CONTROL UNITS. A VARISTOR IN THE OCS CONTROL UNIT LOCATED IN THE PASSENGER SEAT CUSHION MAY HAVE BEEN MANUFACTURED OUT OF SPECIFICATION. UNDER CERTAIN CONDITIONS, THIS COULD CAUSE AN INTERRUPTION OF SIGNAL BETWEEN THE OCS AND THE AIR BAG CONTROL UNIT (ACU).
Consequence: THIS COULD RESULT IN THE PASSENGER AIR BAG BEING SUPPRESSED WHICH COULD FAIL TO PROVIDE ADEQUATE PROTECTION IN THE EVENT OF A CRASH.
Remedy: DEALERS WILL TEST THE SIGNAL BETWEEN THE OCS AND ACU SYSTEMS USING A SPECIAL TOOL TO CHECK THAT IT IS FUNCTIONING AS DESIGNED. IF NECESSARY, THE SEAT CUSHION (CONTAINING OCS HARDWARE) WILL BE REPLACED WITH A NEW ONE MANUFACTURED TO SPECIFICATION. THE RECALL BEGAN ON NOVEMBER 4, 2008. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261 OR INFINITI AT 1-800-662-6200.
NISSAN IS RECALLING 16,365 MY 2008 INFINITI EX35 AND MY 2009 NISSAN MURANO VEHICLES. DUE TO INCORRECT SOFTWARE PROGRAMMING, THE AIR BAG CONTROL UNIT (ACU) MAY CAUSE THE PASSENGER AIR BAG NOT TO OPERATE AS DESIGNED IF THE VEHICLE BATTERY BECOMES SIGNIFICANTLY DISCHARGED.
Consequence & remedy
Consequence: THIS COULD RESULT IN THE PASSENGER AIR BAG NOT INFLATING IN A CRASH IN WHICH IT WAS DESIGNED TO DO SO, AND INCREASING THE RISK OF INJURY.
Remedy: DEALERS WILL REPROGRAM THE ACU IN AFFECTED VEHICLES. THE RECALL BEGAN ON FEBRUARY 19, 2008. OWNERS MAY CONTACT INFINITI AT 1-800-662-6200 OR NISSAN AT 1-800-647-7261.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2
EA18001 · Extended Braking Distances
Opened Apr 18, 2018 · Closed Jan 17, 2023
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip
On April 18, 2018, the Office of Defects Investigation (ODI) opened Engineering Analysis (EA) 18-001 to investigate reports of braking concerns in model year (MY) 2009 Nissan Murano vehicles. A failure of the hydraulic control unit (HCU) portion of the antilock brake system (ABS), which involves improper operation of an internal hydraulic control valve(s), can cause extended brake pedal travel and may result in a reduction in overall braking effectiveness. Tier-one supplier Continental manufactured the HCU for Nissan.The corrosion-preventive, zinc coating used on the armatures of the normally closed (NC) valves within ABS HCU may react with brake fluids lacking sufficient corrosion-preventative additives. This reaction can cause the formation of a gelatinous material, which may cause the NC valves to close slowly. Over time, the gel can solidify to an extent such that the spring used to return the valve to the closed position may not be able to overcome the gel buildup, allowing the NC valve to remain open. If any of the four NC valves remains open, fluid will be diverted to one or two accumulator(s). This misdirected fluid has the net effect of causing brake pedal travel to increase, however enough stroke remains in the pedal to generate braking force. Although the hydraulic braking system remains intact and full braking force is maintained once the pedal travels the additional distance, when this condition occurs, the initial increase in brake pedal travel could result in increased stopping distance. An existing Nissan Service Campaign was launched for MY 2009 vehicles built prior to 11/1/2007. After consultation with ODI as part of EA18-001, Nissan decided to expand this population to the full range of MY2009 Murano vehicles. Later Murano vehicles exhibit significantly lower rates of malfunction.During this investigation 156 complaints were identified that related to the braking concern. Within the complainants 2 allege crashes with 4 injuries. The Nissan reports from investigation Information Request letter responses, were similar in content and identified 870 reports with 16 crashes and no injuries.On December 19, 2018, Nissan notified ODI it would conduct a safety recall (18V916) to remedy the ABS modules on certain MY 2009 Nissan Murano vehicles. The remedy procedure involves dealers flushing the brake system with DOT 4 fluid. The HCU will then be tested to detect a possible stuck valve condition. If necessary, the HCU will be replaced. The 2010-14 Murano SUVs outside the recall population and equipped with zinc-coated armatures will be inspected under a service campaign P0A08 using the same procedure as recall 18V916.Continental HCUs with a redesigned armature coating were phased into new vehicle production after December 2014 and do not appear to be experiencing corrosion. The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI. Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or MY vehicles outside of the recall scope. The agency reserves the right to take further action if warranted by the circumstances.For a complete summary of this investigation and related consumer complaints, please see attached closing resume document.
PE17002 · Extended Braking Distances
Opened May 3, 2017 · Closed May 4, 2018
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Air:antilock; Service Brakes, Air:antilock:control Unit/module
The Office of Defects Investigation (ODI) is closing this Preliminary Evaluation and upgrading to an Engineering Analysis (EA) 18-001.During the PE, ODI requested and reviewed information provided by Nissan including consumer complaints and other field and technical data related to failures of the hydraulic control unit (HCU), an electro-mechanical brake system component that provides antilock braking and other functionality in the subject model year (MY) 2009 Murano.The subject failure of the HCU, which involves improper operation of an internal hydraulic control valve, can cause extended brake pedal travel and may result in a reduction in overall braking effectiveness.Tier-one supplier Continental manufactured the HCU for Nissan.ODI currently recognizes 484 subject vehicle complaints that appear related to the alleged defect.Fourteen crash allegations, with three non-life threatening injuries are under evaluation also.ODI has been monitoring consumer complaints received, and in some cases has obtained suspect HCUs from complainants' vehicles.Recovered HCUs sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio are under evaluation, and VRTC has conducted limited vehicle testing also.In a July 28, 2017 submission, Nissan acknowledged that a failure of the HCU can result in increased brake pedal travel during braking.Nissan's analysis of returned parts revealed that a zinc coating used on the normally closed valve assemblies inside the HCU may react with certain brake fluid constituents.The reaction results in the formation of a gelatinous material that can harden with time and prevent the valve from closing after opening in an ABS event.When this occurs, Nissan maintains that the hydraulic brake system remains intact and that full braking is available once the pedal travels an additional distance, about 36 mm according to Nissan.Although still under investigation, Nissan states it has not determined the condition represents an unreasonable risk to motor vehicle safety, citing low rate and vehicle age as additional factors.In March 2018, Nissan began conducting a customer satisfaction campaign on certain MY 2009 Murano to service (flush and replace the brake fluid), and then test and replace the HCU as needed.The campaign is being conducted free of charge to customers.During the EA, ODI will request VRTC continue to evaluate the cause and consequence of HCU failures, including the affects of multi-valve failures.ODI will further study the potential scope of the alleged defect as it understands similar HCUs and brake fluid is used in other MY Muranos, and potentially in other Nissan models as well.ODI notes that improved valve coatings were introduced on Nissan HCUs at some subsequent stage.
Additional source detail variants (3)
Service Brakes, Air:antilock:control Unit/module
The Office of Defects Investigation (ODI) is closing this Preliminary Evaluation and upgrading to an Engineering Analysis (EA) 18-001.During the PE, ODI requested and reviewed information provided by Nissan including consumer complaints and other field and technical data related to failures of the hydraulic control unit (HCU), an electro-mechanical brake system component that provides antilock braking and other functionality in the subject model year (MY) 2009 Murano.The subject failure of the HCU, which involves improper operation of an internal hydraulic control valve, can cause extended brake pedal travel and may result in a reduction in overall braking effectiveness.Tier-one supplier Continental manufactured the HCU for Nissan.ODI currently recognizes 484 subject vehicle complaints that appear related to the alleged defect.Fourteen crash allegations, with three non-life threatening injuries are under evaluation also.ODI has been monitoring consumer complaints received, and in some cases has obtained suspect HCUs from complainants' vehicles.Recovered HCUs sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio are under evaluation, and VRTC has conducted limited vehicle testing also.In a July 28, 2017 submission, Nissan acknowledged that a failure of the HCU can result in increased brake pedal travel during braking.Nissan's analysis of returned parts revealed that a zinc coating used on the normally closed valve assemblies inside the HCU may react with certain brake fluid constituents.The reaction results in the formation of a gelatinous material that can harden with time and prevent the valve from closing after opening in an ABS event.When this occurs, Nissan maintains that the hydraulic brake system remains intact and that full braking is available once the pedal travels an additional distance, about 36 mm according to Nissan.Although still under investigation, Nissan states it has not determined the condition represents an unreasonable risk to motor vehicle safety, citing low rate and vehicle age as additional factors.In March 2018, Nissan began conducting a customer satisfaction campaign on certain MY 2009 Murano to service (flush and replace the brake fluid), and then test and replace the HCU as needed.The campaign is being conducted free of charge to customers.During the EA, ODI will request VRTC continue to evaluate the cause and consequence of HCU failures, including the affects of multi-valve failures.ODI will further study the potential scope of the alleged defect as it understands similar HCUs and brake fluid is used in other MY Muranos, and potentially in other Nissan models as well.ODI notes that improved valve coatings were introduced on Nissan HCUs at some subsequent stage.
Service Brakes, Air:antilock
The Office of Defects Investigation (ODI) is closing this Preliminary Evaluation and upgrading to an Engineering Analysis (EA) 18-001.During the PE, ODI requested and reviewed information provided by Nissan including consumer complaints and other field and technical data related to failures of the hydraulic control unit (HCU), an electro-mechanical brake system component that provides antilock braking and other functionality in the subject model year (MY) 2009 Murano.The subject failure of the HCU, which involves improper operation of an internal hydraulic control valve, can cause extended brake pedal travel and may result in a reduction in overall braking effectiveness.Tier-one supplier Continental manufactured the HCU for Nissan.ODI currently recognizes 484 subject vehicle complaints that appear related to the alleged defect.Fourteen crash allegations, with three non-life threatening injuries are under evaluation also.ODI has been monitoring consumer complaints received, and in some cases has obtained suspect HCUs from complainants' vehicles.Recovered HCUs sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio are under evaluation, and VRTC has conducted limited vehicle testing also.In a July 28, 2017 submission, Nissan acknowledged that a failure of the HCU can result in increased brake pedal travel during braking.Nissan's analysis of returned parts revealed that a zinc coating used on the normally closed valve assemblies inside the HCU may react with certain brake fluid constituents.The reaction results in the formation of a gelatinous material that can harden with time and prevent the valve from closing after opening in an ABS event.When this occurs, Nissan maintains that the hydraulic brake system remains intact and that full braking is available once the pedal travels an additional distance, about 36 mm according to Nissan.Although still under investigation, Nissan states it has not determined the condition represents an unreasonable risk to motor vehicle safety, citing low rate and vehicle age as additional factors.In March 2018, Nissan began conducting a customer satisfaction campaign on certain MY 2009 Murano to service (flush and replace the brake fluid), and then test and replace the HCU as needed.The campaign is being conducted free of charge to customers.During the EA, ODI will request VRTC continue to evaluate the cause and consequence of HCU failures, including the affects of multi-valve failures.ODI will further study the potential scope of the alleged defect as it understands similar HCUs and brake fluid is used in other MY Muranos, and potentially in other Nissan models as well.ODI notes that improved valve coatings were introduced on Nissan HCUs at some subsequent stage.
Service Brakes
The Office of Defects Investigation (ODI) is closing this Preliminary Evaluation and upgrading to an Engineering Analysis (EA) 18-001.During the PE, ODI requested and reviewed information provided by Nissan including consumer complaints and other field and technical data related to failures of the hydraulic control unit (HCU), an electro-mechanical brake system component that provides antilock braking and other functionality in the subject model year (MY) 2009 Murano.The subject failure of the HCU, which involves improper operation of an internal hydraulic control valve, can cause extended brake pedal travel and may result in a reduction in overall braking effectiveness.Tier-one supplier Continental manufactured the HCU for Nissan.ODI currently recognizes 484 subject vehicle complaints that appear related to the alleged defect.Fourteen crash allegations, with three non-life threatening injuries are under evaluation also.ODI has been monitoring consumer complaints received, and in some cases has obtained suspect HCUs from complainants' vehicles.Recovered HCUs sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio are under evaluation, and VRTC has conducted limited vehicle testing also.In a July 28, 2017 submission, Nissan acknowledged that a failure of the HCU can result in increased brake pedal travel during braking.Nissan's analysis of returned parts revealed that a zinc coating used on the normally closed valve assemblies inside the HCU may react with certain brake fluid constituents.The reaction results in the formation of a gelatinous material that can harden with time and prevent the valve from closing after opening in an ABS event.When this occurs, Nissan maintains that the hydraulic brake system remains intact and that full braking is available once the pedal travels an additional distance, about 36 mm according to Nissan.Although still under investigation, Nissan states it has not determined the condition represents an unreasonable risk to motor vehicle safety, citing low rate and vehicle age as additional factors.In March 2018, Nissan began conducting a customer satisfaction campaign on certain MY 2009 Murano to service (flush and replace the brake fluid), and then test and replace the HCU as needed.The campaign is being conducted free of charge to customers.During the EA, ODI will request VRTC continue to evaluate the cause and consequence of HCU failures, including the affects of multi-valve failures.ODI will further study the potential scope of the alleged defect as it understands similar HCUs and brake fluid is used in other MY Muranos, and potentially in other Nissan models as well.ODI notes that improved valve coatings were introduced on Nissan HCUs at some subsequent stage.
2009 Nissan Murano Problems, Complaints & Recalls | Skip That Year
Illustration