IllustrationTHE CAR IGNITION WILL NOT LET ME TURN IT
2008 Nissan Maxima
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2008 Nissan Maxima do not stand out strongly from the model-year median of 99.
About this comparison →How this year compares
Owner complaints by model year
Compare all Maxima years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
120–25K
625–50K
1050–75K
1175–100K
15100–150K
5150K+
59 reports with mileage · 19 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 23 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 21 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 8 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
7 crash reports0 fire reports3 injury reports
Unknown Or Other complaints
4 reportsWHILE WAITING FOR A TRAFFIC LIGHT TO TURN GREEN THE CAR STALLED. HAD TO TURN THE CAR STARTER SEVERAL TIMES BEFORE THE CAR WOULD START AGAIN. THE DEALER DIAGNOSED THE ISSUE AS A FAILED CAM AND CRANK SHAFT SENSOR. PRIOR TO THIS INCIDENT THE CAR HAD TROUBLE STARTING AND WOULD STALL WHEN THE ENGINE WAS COLD. THE DEALER DIAGNOSED…
Read full complaint
WHILE WAITING FOR A TRAFFIC LIGHT TO TURN GREEN THE CAR STALLED. HAD TO TURN THE CAR STARTER SEVERAL TIMES BEFORE THE CAR WOULD START AGAIN. THE DEALER DIAGNOSED THE ISSUE AS A FAILED CAM AND CRANK SHAFT SENSOR. PRIOR TO THIS INCIDENT THE CAR HAD TROUBLE STARTING AND WOULD STALL WHEN THE ENGINE WAS COLD. THE DEALER DIAGNOSED THE ISSUE AS THE FUEL PUMP NOT HOLDING ITS PRESSURE. CAM AND CRANK SHAFT SENSORS WERE REPLACED AS WELL AS THE FUEL PUMP.
DRIVER AND PASSENGER FLOOR RUSTED BIG WHOLE ON BOTH SIDE. JUST LOOK UNDER THE CAR THIS WEEK WHEN I TOOK IT TO THE MECHANIC
RUSTING IN THEIR CARS' FLOORBOARDS. RUSTING LARGE ENOUGH TO SEE THROUGH THE CAR FLOOR.
Official recalls
0No recalls in this snapshot.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE08045 · Transmission Hose Leak
Opened Jul 23, 2008 · Closed Oct 24, 2008
Status: closed (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:cooling Unit And Lines
THIS PE WAS OPENED FOR MODEL YEAR (MY) 2008 NISSAN MAXIMA VEHICLES BASED ON EARLY WARNING DATA THAT THE AUTOMATIC TRANSMISSION COOLER HOSE MAY HAVE PINHOLES AND/OR CRACKS RESULTING IN A TRANSMISSION FLUID LEAK.THE LEAKED FLUID CAN CONTACT THE EXHAUST SYSTEM AND IGNITE.NISSAN HAS SHOWN THAT THE ROOT CAUSE OF THE PINHOLES AND/OR CRACKS IN THE HOSE IS EXCESSIVE STRESS DURING THE MANUFACTURE FORMING PROCESS RESULTING IN HOSE DEFORMATION AT LOADING ONTO A MANDREL, OR DAMAGE DURING UN-LOADING.REGARDING LOADING STRESS, NISSAN STATES, WHEN EXCESSIVE STRESS IS APPLIED WHILE LOADING THE HOSE ONTO THE MANDREL, HOSE DEFORMATION (WHICH LOOKS LIKE A BULGE) CAN OCCUR AROUND THE BENDING AREA.A CRACK WILL START TO FORM ON THE INSIDE OF THE HOSE AT THE AREA OF DEFORMATION.REGARDING UNLOADING STRESS, NISSAN STATES, AFTER THE CURING PROCESS, IN SOME INSTANCES THE HOSE STUCK TO THE MANDREL TIGHTLY AND THE OPERATOR HAD TO APPLY A SIGNIFICANT AMOUNT OF FORCE TO PULL THE HOSE FROM THE MANDREL.IF THIS OPERATION WAS PERFORMED ROUGHLY, THE INTERIOR OF THE HOSE COULD BE DAMAGED BY THE MANDREL EDGE. NISSAN ALSO STATES, BECAUSE OF THE WAY THE HOSES RECEIVED INTERNAL DAMAGE, A DAMAGED HOSE WAS PRODUCED AS A RARE, RANDOM EVENT RATHER THAN SYSTEMATICALLY.THE TRANSMISSION HOSE SUPPLIER, COOPER STANDARD AUTOMOTIVE, IMPLEMENTED PROCESS IMPROVEMENTS THAT LIMIT EXCESSIVE STRESS ON THE HOSE DURING MANUFACTURE. NISSAN HAS SHOWN THAT THIS TRANSMISSION COOLER HOSE WAS ASSEMBLED ON MY 2007 AND MY 2008 MAXIMA VEHICLES.NISSAN REDESIGNED THE TRANSMISSION COOLER HOSE ON MY 2009 MAXIMA, AND THE HOSE IS MANUFACTURED BY A NEW SUPPLIER.NISSAN HAS ALSO SHOWN THAT THE LEAKS MOSTLY OCCUR WITHIN THE FIRST 2000 MILES OF SERVICE WITH A SEVERE DROP IN INCIDENTS BEYOND 2000 MILES OF SERVICE.MOST LEAKS HAVE ALREADY OCCURRED, AND THE ONE FIRE WAS MINOR. A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.ACCORDINGLY THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.
Additional source detail variants (2)
Power Train:automatic Transmission:cooling Unit And Lines
THIS PE WAS OPENED FOR MODEL YEAR (MY) 2008 NISSAN MAXIMA VEHICLES BASED ON EARLY WARNING DATA THAT THE AUTOMATIC TRANSMISSION COOLER HOSE MAY HAVE PINHOLES AND/OR CRACKS RESULTING IN A TRANSMISSION FLUID LEAK.THE LEAKED FLUID CAN CONTACT THE EXHAUST SYSTEM AND IGNITE.NISSAN HAS SHOWN THAT THE ROOT CAUSE OF THE PINHOLES AND/OR CRACKS IN THE HOSE IS EXCESSIVE STRESS DURING THE MANUFACTURE FORMING PROCESS RESULTING IN HOSE DEFORMATION AT LOADING ONTO A MANDREL, OR DAMAGE DURING UN-LOADING.REGARDING LOADING STRESS, NISSAN STATES, WHEN EXCESSIVE STRESS IS APPLIED WHILE LOADING THE HOSE ONTO THE MANDREL, HOSE DEFORMATION (WHICH LOOKS LIKE A BULGE) CAN OCCUR AROUND THE BENDING AREA.A CRACK WILL START TO FORM ON THE INSIDE OF THE HOSE AT THE AREA OF DEFORMATION.REGARDING UNLOADING STRESS, NISSAN STATES, AFTER THE CURING PROCESS, IN SOME INSTANCES THE HOSE STUCK TO THE MANDREL TIGHTLY AND THE OPERATOR HAD TO APPLY A SIGNIFICANT AMOUNT OF FORCE TO PULL THE HOSE FROM THE MANDREL.IF THIS OPERATION WAS PERFORMED ROUGHLY, THE INTERIOR OF THE HOSE COULD BE DAMAGED BY THE MANDREL EDGE. NISSAN ALSO STATES, BECAUSE OF THE WAY THE HOSES RECEIVED INTERNAL DAMAGE, A DAMAGED HOSE WAS PRODUCED AS A RARE, RANDOM EVENT RATHER THAN SYSTEMATICALLY.THE TRANSMISSION HOSE SUPPLIER, COOPER STANDARD AUTOMOTIVE, IMPLEMENTED PROCESS IMPROVEMENTS THAT LIMIT EXCESSIVE STRESS ON THE HOSE DURING MANUFACTURE. NISSAN HAS SHOWN THAT THIS TRANSMISSION COOLER HOSE WAS ASSEMBLED ON MY 2007 AND MY 2008 MAXIMA VEHICLES.NISSAN REDESIGNED THE TRANSMISSION COOLER HOSE ON MY 2009 MAXIMA, AND THE HOSE IS MANUFACTURED BY A NEW SUPPLIER.NISSAN HAS ALSO SHOWN THAT THE LEAKS MOSTLY OCCUR WITHIN THE FIRST 2000 MILES OF SERVICE WITH A SEVERE DROP IN INCIDENTS BEYOND 2000 MILES OF SERVICE.MOST LEAKS HAVE ALREADY OCCURRED, AND THE ONE FIRE WAS MINOR. A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.ACCORDINGLY THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.
Power Train:automatic Transmission
THIS PE WAS OPENED FOR MODEL YEAR (MY) 2008 NISSAN MAXIMA VEHICLES BASED ON EARLY WARNING DATA THAT THE AUTOMATIC TRANSMISSION COOLER HOSE MAY HAVE PINHOLES AND/OR CRACKS RESULTING IN A TRANSMISSION FLUID LEAK.THE LEAKED FLUID CAN CONTACT THE EXHAUST SYSTEM AND IGNITE.NISSAN HAS SHOWN THAT THE ROOT CAUSE OF THE PINHOLES AND/OR CRACKS IN THE HOSE IS EXCESSIVE STRESS DURING THE MANUFACTURE FORMING PROCESS RESULTING IN HOSE DEFORMATION AT LOADING ONTO A MANDREL, OR DAMAGE DURING UN-LOADING.REGARDING LOADING STRESS, NISSAN STATES, WHEN EXCESSIVE STRESS IS APPLIED WHILE LOADING THE HOSE ONTO THE MANDREL, HOSE DEFORMATION (WHICH LOOKS LIKE A BULGE) CAN OCCUR AROUND THE BENDING AREA.A CRACK WILL START TO FORM ON THE INSIDE OF THE HOSE AT THE AREA OF DEFORMATION.REGARDING UNLOADING STRESS, NISSAN STATES, AFTER THE CURING PROCESS, IN SOME INSTANCES THE HOSE STUCK TO THE MANDREL TIGHTLY AND THE OPERATOR HAD TO APPLY A SIGNIFICANT AMOUNT OF FORCE TO PULL THE HOSE FROM THE MANDREL.IF THIS OPERATION WAS PERFORMED ROUGHLY, THE INTERIOR OF THE HOSE COULD BE DAMAGED BY THE MANDREL EDGE. NISSAN ALSO STATES, BECAUSE OF THE WAY THE HOSES RECEIVED INTERNAL DAMAGE, A DAMAGED HOSE WAS PRODUCED AS A RARE, RANDOM EVENT RATHER THAN SYSTEMATICALLY.THE TRANSMISSION HOSE SUPPLIER, COOPER STANDARD AUTOMOTIVE, IMPLEMENTED PROCESS IMPROVEMENTS THAT LIMIT EXCESSIVE STRESS ON THE HOSE DURING MANUFACTURE. NISSAN HAS SHOWN THAT THIS TRANSMISSION COOLER HOSE WAS ASSEMBLED ON MY 2007 AND MY 2008 MAXIMA VEHICLES.NISSAN REDESIGNED THE TRANSMISSION COOLER HOSE ON MY 2009 MAXIMA, AND THE HOSE IS MANUFACTURED BY A NEW SUPPLIER.NISSAN HAS ALSO SHOWN THAT THE LEAKS MOSTLY OCCUR WITHIN THE FIRST 2000 MILES OF SERVICE WITH A SEVERE DROP IN INCIDENTS BEYOND 2000 MILES OF SERVICE.MOST LEAKS HAVE ALREADY OCCURRED, AND THE ONE FIRE WAS MINOR. A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.ACCORDINGLY THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.