IllustrationVEHICLE HEAD LIGHTS WERE STOLEN FROM A 2003 NISSAN MAXIMA. *MR *SCC *JB
2003 Nissan Maxima
Owner reports · Recalls · Investigations
More warning signs than most Maxima years
Owner complaints for the 2003 Nissan Maxima are substantially higher than the model-year median of 99.
About this comparison →How this year compares
Owner complaints by model year
Compare all Maxima years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
280–25K
1925–50K
1850–75K
2375–100K
33100–150K
26150K+
147 reports with mileage · 59 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine And Engine Cooling. Review the 54 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 43 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 35 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
13 crash reports2 fire reports10 injury reports
Exterior Lighting complaints
26 reportsPROBLEMS WITH THEFT OF VEHICLE'S HEADLIGHTS.*MR VEHICLE WAS VANDALIZE THREE TIMES FOR THE HEADLIGHTS. AFTER THE SECOND INCIDENT, AN ANTI-THEFT DEVICE WAS INSTALLED. AFTER THE THIRD INCIDENT, THE MANUFACTURER OFFERED A $500.00 INCENTIVE TOWARDS A TRADE IN. CONSUMER SUGGESTED NISSAN GIVE HIM ANOTHER VEHICLE WITHOUT THE HEADLIGH…
Read full complaint
PROBLEMS WITH THEFT OF VEHICLE'S HEADLIGHTS.*MR VEHICLE WAS VANDALIZE THREE TIMES FOR THE HEADLIGHTS. AFTER THE SECOND INCIDENT, AN ANTI-THEFT DEVICE WAS INSTALLED. AFTER THE THIRD INCIDENT, THE MANUFACTURER OFFERED A $500.00 INCENTIVE TOWARDS A TRADE IN. CONSUMER SUGGESTED NISSAN GIVE HIM ANOTHER VEHICLE WITHOUT THE HEADLIGHTS, REFUND HIS MONEY, OR RECALL THE VEHICLES DUE TO POOR ASSEMBLY. THE DEALERSHIP THAT PURCHASED THE VEHICLE FROM THE CONSUMER WOULD MAKE A REASONABLE DEAL. *PH *JB
CONSUMER STATED THE VEHICLE HAD A DESIGN DEFECT WHICH MAKE IT EASY FOR THE HEADLIGHTS TO BE STOLEN BY JUST "POPPING" THEM OUT. THERE WAS AN EXCESSIVE AMOUNT OF SPACE BETWEEN HEADLAMP ASSEMBLY AND VEHICLE'S FRAME. ANY OBJECT CAN BE INSERTED IN THE SPACE TO DISLODGE THE HEADLAMP. *PH *SCC *JB
THE HEADLIGHTS WERE STOLEN ON TWO DIFFERENT OCCASIONS. THE CONSUMER STATED NISSAN SHOULD ASSUME RESPONSIBILITY FOR THIS DEFECT. *PH *JB
BOTH HID HEADLIGHTS (XENON) WERE STOLEN FROM MY 2003 NISSAN MAXIMA. THE DEALER WHERE I BOUGHT THE CAR REFUSE TO REPLACE THE HEADLIGHTS WITH THOSE OF THE 2001 MODEL. I FOUND A DEALERSHIP THAT INSTALLED THE HALOGEN HEADLIGHTS OF THE 2001 MAXIMA ON MY CAR. NISSAN'S CONSUMER AFFAIRS DEPARTMENT REFUSED TO CONSIDER THIS PROBLEM AS …
Read full complaint
BOTH HID HEADLIGHTS (XENON) WERE STOLEN FROM MY 2003 NISSAN MAXIMA. THE DEALER WHERE I BOUGHT THE CAR REFUSE TO REPLACE THE HEADLIGHTS WITH THOSE OF THE 2001 MODEL. I FOUND A DEALERSHIP THAT INSTALLED THE HALOGEN HEADLIGHTS OF THE 2001 MAXIMA ON MY CAR. NISSAN'S CONSUMER AFFAIRS DEPARTMENT REFUSED TO CONSIDER THIS PROBLEM AS A DESIGN FLAW AND OFFERS NO HELP TO OWNER TO SECURE THESE HEADLIGHTS THAT ARE SO EASILY STOLEN.*AK
I HAVE A 2003 NISSAN MAXIMA AND THE HEADLIGHTS WHERE STOLEN. NISSAN HAS MADE THE HEADLIGHTS TO EASY TO TAKE. *NLM
THE HEAD LAMPS (HEADLIGHTS) WERE STOLEN TWICE. EACH HEAD LIGHT WAS $800.00. THE DEALER STATED THEY COULD BE REMOVED EASILY. THE CONSUMER STATED THIS IS A POOR DESIGN. *NLM *TS *JB
I PURCHASED THE 2003 NISSAN MAXIMATHE END OF JANUARY 2003, I WAS NEVER TOLD THAT THE HEADLIGHTS ON THESE CARS ARE EASILY REMOVEABLE, BY SIMPLY POPPING THEM OUT WITH A SCREW DRIVER. SO ON MAY 21, MY CAR'S HEADLIGHTS WERE STOLEN. I COMPLAINED TO THE NISSAN CORP BUT WAS TOLD THAT THERE WAS NOTH THEY COULD DO ABOUT THE PROBLEM. THEY…
Read full complaint
I PURCHASED THE 2003 NISSAN MAXIMATHE END OF JANUARY 2003, I WAS NEVER TOLD THAT THE HEADLIGHTS ON THESE CARS ARE EASILY REMOVEABLE, BY SIMPLY POPPING THEM OUT WITH A SCREW DRIVER. SO ON MAY 21, MY CAR'S HEADLIGHTS WERE STOLEN. I COMPLAINED TO THE NISSAN CORP BUT WAS TOLD THAT THERE WAS NOTH THEY COULD DO ABOUT THE PROBLEM. THEY ARE AWARE OF THE SITUATION, IN FACT THEY HAVE ALREADY INTRODUCED THE 2004 MODEL WITH THE HEADLIGHTS TAMPER PROOF. THE POLICE TOLD ME THAT THIS MODEL CAR IS VERY POPULAR WITH THE THIEVES AND I SHOULD NOT KEEP THIS C AR IN THE STREET FOR MORE THEN 10MINS AT A TIME. SO BASICALLY, I BOUGHT A CAR TO KEEP UNDER LOCK AND KEY AND NOT USE AT ALL. WHY CAN'T NISSAN RECALL THESE CARS AND FIX THE PROBLEM, BECAUSE EVERY TIME THE LIGHTS ARE STOLEN, THE DEMAGE IS MORE THEN $2,000.00, ALSO WHAT HAPPENS IF I AM A DISTANCE AWAY AND THEY STEAL MY HEADLIGHTS, I WILL NOT BE ABLE TO DRIVE BACK HOME OR RISK DRIVING WITH NO HEADLIGHTS AND MAYBE HURT MYSELF OR SOMEONE ELSE. PLEASE CHECK INTO THIS MATTER AND ADVISE ME.
PASSENGER HID LIGHT STOLEN AND WIRES CUT. LITERALLY TOOK THIEVES MINUTES, PERHAPS SECONDS.
HID HEADLIGHTS WERE STOLEN. TOOK LESS THAN 10 SECONDS FOR THIEF TO STEAL HEADLIGHTS. *NLM
Official recalls
320V008000 · Air Bags:frontal:passenger Side:inflator Module
Jan 9, 2020
Nissan North America, Inc. (Nissan) is recalling certain 2001-2003 Maxima, 2002-2006 Sentra, 2002-2004 Pathfinder, 2007-2011 Versa Sedan and Versa Hatchback, 2001-2004 Infiniti I30 and I35, 2002-2003 Inifiniti QX4, 2003-2008 Infiniti FX35 and FX45 and 2006-2010 M35 and M45 vehicles. The vehicles are equipped with non-desiccated, frontal passenger air bag inflators containing phase stabilized ammonium nitrate (PSAN) propellant that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the front passenger air bag inflators with alternate desiccated inflators, free of charge. The recall began February 12, 2020. Owners may contact Nissan customer service at 888-737-9511 or Infiniti customer service at 888-810-3715.
15V287000 · Air Bags
May 15, 2015
Nissan North America, Inc. (Nissan) is recalling certain model year 2001-2003 Nissan Maxima, 2002-2004 Pathfinder, 2002-2006 Sentra, 2002-2003 Infiniti QX4 and I35, 2003 FX35 and FX45, and 2001 I30 vehicles. Upon deployment of the passenger side frontal air bag, excessive internal pressure may cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could rupture with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the passenger air bag inflator, free of charge. The recall began on June 15, 2015. Owners may contact Nissan customer service at 1-800-647-7261. Note: On December 18, 2015 Nissan informed NHTSA of an amendment of this recall to remove 2004-2005 Infiniti FX35 and FX45 vehicles.
03V455000 · Engine And Engine Cooling
Nov 17, 2003
ON CERTAIN PASSENGER VEHICLES, THE CIRCUIT BOARD FOR THE CRANK POSITION SENSOR OR CAM POSITION SENSOR MAY HAVE AN IMPROPER SOLDER JOINT DUE TO SOLDER DEFORMATION CAUSED BY HEAT STRESS ACCELERATED BY THE EXISTENCE OF FLUX RESIDUE DURING THE SOLDERING PROCESS.
Consequence & remedy
Consequence: THIS COULD CAUSE THE "SERVICE ENGINE SOON" WARNING LIGHT TO COME ON, CREATE A NO START CONDITION, CAUSE REDUCED ENGINE POWER, OR CAUSE THE ENGINE TO STOP RUNNING WITHOUT WARNING DURING VEHICLE OPERATION, WHICH COULD RESULT IN A CRASH.
Remedy: DEALERS WILL REPLACE THE CRANK POSITION SENSORS. CAMSHAFT POSITION SENSOR(S), AND IN SOME CASES, THE VARIABLE TIMING CONTROL SENSOR(S). VEHICLES INVOLVED IN A PREVIOUS RECALL CAMPAIGN, 01V357, ARE ALSO INCLUDED IN THIS NEW CAMPAIGN. THE REPLACEMENT SENSORS USED IN THAT CAMPAIGN ARE ALSO AFFECTED. OWNER NOTIFICATION BEGAN ON DECEMBER 22, 2003. OWNERS SHOULD CONTACT NISSAN AT 1-800-647-7261 OR INFINITI AT 1-800-662-6200.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.