NHTSA owner reports · September 18, 2026 snapshot.
Structure complaints
11 reportsClear category filter95,700 miles · Feb 19, 2015
Air BagsStructureVehicle Speed ControlCrash
WHILE PARKING CAR IT SPONTANEOUSLY ACCELERATED ACROSS THE PARKING LOT, THE BORDERING STREET AND INTO ANOTHER PARKING LOT BEFORE STOPPING. THE CARS LEFT SIDE, RIGHT SIDE, FRONT BUMPER, TIRES AND SUSPENSION WERE DAMAGED. THOUGH NO OTHER CARS WERE HIT, COMMERCIAL GARBAGE CANS, STOP SIGN, TELEPHONE POLE AND A SERIES 4 CURBS INFL…
Read full complaint
WHILE PARKING CAR IT SPONTANEOUSLY ACCELERATED ACROSS THE PARKING LOT, THE BORDERING STREET AND INTO ANOTHER PARKING LOT BEFORE STOPPING. THE CARS LEFT SIDE, RIGHT SIDE, FRONT BUMPER, TIRES AND SUSPENSION WERE DAMAGED. THOUGH NO OTHER CARS WERE HIT, COMMERCIAL GARBAGE CANS, STOP SIGN, TELEPHONE POLE AND A SERIES 4 CURBS INFLICTED DAMAGE. THE AIR BAGS DID NOT DEPLOY DESPITE HAVING THEM CHECKED BY THE DEALER AS REQUIRED BY A RECALL. *TR
NHTSA ODI #10689418
Mileage unknown · Jul 23, 2012
Engine And Engine CoolingPower TrainStructure
THE RADIATOR CORE SUPPORT IS RUSTING AND HAS LEAD TO A LARGE HOLE ON THE BOTTOM. THE ENGINE BRACE IS MOUNTED WHERE THE RUST IS FORMING. IF THE RUST FORMS BAD ENOUGH AROUND THE BOLTS THE ENGINE COULD FALL DOWN. ALSO THE HOOD LATCH IS CONNECTED THE BOTTOM OF THE CORE SUPPORT. IF THIS FAILS THE RUST CAN CAUSE THE HOOD TO OPEN WHILE…
Read full complaint
THE RADIATOR CORE SUPPORT IS RUSTING AND HAS LEAD TO A LARGE HOLE ON THE BOTTOM. THE ENGINE BRACE IS MOUNTED WHERE THE RUST IS FORMING. IF THE RUST FORMS BAD ENOUGH AROUND THE BOLTS THE ENGINE COULD FALL DOWN. ALSO THE HOOD LATCH IS CONNECTED THE BOTTOM OF THE CORE SUPPORT. IF THIS FAILS THE RUST CAN CAUSE THE HOOD TO OPEN WHILE DRIVING. *TR
NHTSA ODI #10466978
Mileage unknown · Dec 21, 2005
Structure
I HAVE 2 NISSAN MAXIMA'S, BOTH 2002 MODELS. BOTH OF THESE CARS HAVE FAULTY HINGES ON THE DRIVERS DOOR CAUSING THE DOORS TO SAG AND NOT OPERATE PROPERLY. I DO NOT THINK IT IS JUST A COINCIDENCE THAT THIS HAS HAPPENED ON BOTH VEHICLES AND WONDER HOW MANY OTHER OF THESE CARS HAS THE SAME PROBLEM. *JB
NHTSA ODI #10145773
5,000 miles · Nov 24, 2004
Structure
PAINT QUALITY IS HORRIBLE. CAR HAS THOUSANDS OF SMALL PAINT CHIPS CONCENTRATED ON THE FRONT BUMPER AND FRONT OF HOOD. THIS IS NOT NORMAL AS NISSAN INSISTS. THEIR PAINT JOBS ARE INFERIOR AND UNFAIR TO THE CONSUMER. *NM
NHTSA ODI #10100494
39,000 miles · Nov 12, 2004
Structure
ON 6/30/04, TOOK MY VEHICLE IN TO MY LOCAL DEALER FOR A NOISE COMING FROM THE FRONT END OF THE CAR. IT SOUNDED LIKE THE STRUT WAS BROKEN OR BOTTOMING OUT. DEALER ALSO THOUGHT IT WAS A STRUT, AND AFTER PUTTING TWO STRUT ASSEMBLIES ON THE CAR, THE PROBLEM WAS NOT RESOLVED. SINCE THEN, THIS DEALER AND ANOTHER DEALER HAVE REPLACED…
Read full complaint
ON 6/30/04, TOOK MY VEHICLE IN TO MY LOCAL DEALER FOR A NOISE COMING FROM THE FRONT END OF THE CAR. IT SOUNDED LIKE THE STRUT WAS BROKEN OR BOTTOMING OUT. DEALER ALSO THOUGHT IT WAS A STRUT, AND AFTER PUTTING TWO STRUT ASSEMBLIES ON THE CAR, THE PROBLEM WAS NOT RESOLVED. SINCE THEN, THIS DEALER AND ANOTHER DEALER HAVE REPLACED LOWER CONTROL ARM, RACK AND PINION, CRADLE, AND NUMEROUS BOLTS TRYING TO FIX THE PROBLEM. NISSAN DEALER TECHNICAL SERVICES AND A NISSAN ENGINEER HAVE INSPECTED THE VEHICLE. NISSAN ENGINEER HAS PINPOINTED THE NOISE TO THE FRAME OF THE CAR. I HAVE BEEN TOLD THAT THERE ARE SUPPORTS OR BRACES WITHIN THE FRAME THAT MAY HAVE BROKEN. THIS VEHICLE HAS NEVER BEEN IN AN ACCIDENT, SO ANY PROBLEM WITHIN THE FRAME ARE A RESULT OF DEFECT CAUSED DURING THE MANUFACTURING OF THE FRAME. *JB
NHTSA ODI #10098729
2,000 miles · Apr 14, 2004
Structure
THE HOOD AND FRONT BUMPER'S PAINT CHIPS TOO EASILY. HAVE COMPLAINED TO DEALERSHIP MANY MANY TIMES WHO STATES THAT IS NORMAL FOR THIS VEHICLE AND THEY CANNOIT ASSIST ME AND I SHOULD OF KNOWN BEFORE PURCHASING. CONTACTED NISSAN CONSUMAR AFFAIRS AND NEVER HEARD BACK FROM THEM AT ALL! THIS WILL HURT MY RESALE VALUE AND LOOKS TERR…
Read full complaint
THE HOOD AND FRONT BUMPER'S PAINT CHIPS TOO EASILY. HAVE COMPLAINED TO DEALERSHIP MANY MANY TIMES WHO STATES THAT IS NORMAL FOR THIS VEHICLE AND THEY CANNOIT ASSIST ME AND I SHOULD OF KNOWN BEFORE PURCHASING. CONTACTED NISSAN CONSUMAR AFFAIRS AND NEVER HEARD BACK FROM THEM AT ALL! THIS WILL HURT MY RESALE VALUE AND LOOKS TERRIBLE, NEEDS TO BE RECONCILED
NHTSA ODI #10066137
Mileage unknown · Oct 30, 2003
Structure
PAINT CHIPS ON HOOD;COMPLAINED TO NISSAN; INSPECTORS CONCLUSION UNSATISFACTORY AND DISPUTED BY OUTSIDE PROFESSIONAL!
NHTSA ODI #10045072
Mileage unknown · Oct 18, 2003
Electrical SystemEquipmentExterior Lighting
HEAD LIGHTS WERE STOLEN FROM THE VEHICLE. DAMAGE WAS DONE TO THE ELECTRICAL SYSTEM, HOOD AND BUMPER BECAUSE THIEF KNEW THAT THERE WAS NO MOTION SENSOR ALARM. THE BRACKETS HOLDING EACH $724 LIGHT IS MADE OF PLASTIC AND CAN EASILY BE SNAPPED/BROKEN. THE ANTI-THEFT KIT DOESN'T DO ANYTHING BECAUSE IT DOESN'T FIX THE ISSUE THAT THE L…
Read full complaint
HEAD LIGHTS WERE STOLEN FROM THE VEHICLE. DAMAGE WAS DONE TO THE ELECTRICAL SYSTEM, HOOD AND BUMPER BECAUSE THIEF KNEW THAT THERE WAS NO MOTION SENSOR ALARM. THE BRACKETS HOLDING EACH $724 LIGHT IS MADE OF PLASTIC AND CAN EASILY BE SNAPPED/BROKEN. THE ANTI-THEFT KIT DOESN'T DO ANYTHING BECAUSE IT DOESN'T FIX THE ISSUE THAT THE LIGHTS CAN STILL BE REMOVED BY BREAKING THE BRACKET WITHOUT OPENING THE HOOD. THE HORN WIRING WAS ALSO REMOVED BECAUSE OF ITS EASY ACCESSIBILITY THROUGH THE GRILL. *LA
NHTSA ODI #10043157
20,000 miles · Sep 22, 2003
Engine And Engine CoolingStructure
EXCESSIVE PAINT CHIPS FROM HOOD AND FRONT BUMPER KNOCKING/PINGING DURING HARD ACCELERATING OR UNDER LOAD. *JB
NHTSA ODI #10039324
Mileage unknown · Aug 22, 2003
Electrical SystemExterior LightingStructure
2K2 HID THEFT. FRONT LIGHTS. HOOD, GRILL, ELECTRICAL, FENDER AND BUMPER DAMAGE.*AK
NHTSA ODI #10033309
Official recalls
6Jan 9, 2020
Nissan North America, Inc. (Nissan) is recalling certain 2001-2003 Maxima, 2002-2006 Sentra, 2002-2004 Pathfinder, 2007-2011 Versa Sedan and Versa Hatchback, 2001-2004 Infiniti I30 and I35, 2002-2003 Inifiniti QX4, 2003-2008 Infiniti FX35 and FX45 and 2006-2010 M35 and M45 vehicles. The vehicles are equipped with non-desiccated, frontal passenger air bag inflators containing phase stabilized ammonium nitrate (PSAN) propellant that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the front passenger air bag inflators with alternate desiccated inflators, free of charge. The recall began February 12, 2020. Owners may contact Nissan customer service at 888-737-9511 or Infiniti customer service at 888-810-3715.
May 15, 2015
Nissan North America, Inc. (Nissan) is recalling certain model year 2001-2003 Nissan Maxima, 2002-2004 Pathfinder, 2002-2006 Sentra, 2002-2003 Infiniti QX4 and I35, 2003 FX35 and FX45, and 2001 I30 vehicles. Upon deployment of the passenger side frontal air bag, excessive internal pressure may cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could rupture with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the passenger air bag inflator, free of charge. The recall began on June 15, 2015. Owners may contact Nissan customer service at 1-800-647-7261. Note: On December 18, 2015 Nissan informed NHTSA of an amendment of this recall to remove 2004-2005 Infiniti FX35 and FX45 vehicles.
Nov 17, 2003
ON CERTAIN PASSENGER VEHICLES, THE CIRCUIT BOARD FOR THE CRANK POSITION SENSOR OR CAM POSITION SENSOR MAY HAVE AN IMPROPER SOLDER JOINT DUE TO SOLDER DEFORMATION CAUSED BY HEAT STRESS ACCELERATED BY THE EXISTENCE OF FLUX RESIDUE DURING THE SOLDERING PROCESS.
Consequence & remedy
Consequence: THIS COULD CAUSE THE "SERVICE ENGINE SOON" WARNING LIGHT TO COME ON, CREATE A NO START CONDITION, CAUSE REDUCED ENGINE POWER, OR CAUSE THE ENGINE TO STOP RUNNING WITHOUT WARNING DURING VEHICLE OPERATION, WHICH COULD RESULT IN A CRASH.
Remedy: DEALERS WILL REPLACE THE CRANK POSITION SENSORS. CAMSHAFT POSITION SENSOR(S), AND IN SOME CASES, THE VARIABLE TIMING CONTROL SENSOR(S). VEHICLES INVOLVED IN A PREVIOUS RECALL CAMPAIGN, 01V357, ARE ALSO INCLUDED IN THIS NEW CAMPAIGN. THE REPLACEMENT SENSORS USED IN THAT CAMPAIGN ARE ALSO AFFECTED. OWNER NOTIFICATION BEGAN ON DECEMBER 22, 2003. OWNERS SHOULD CONTACT NISSAN AT 1-800-647-7261 OR INFINITI AT 1-800-662-6200.
May 30, 2002
ON CERTAIN PASSENGER VEHICLES, THE PIN AT THE END OF THE FRONT SUSPENSION TRANSVERSE LINK (LOWER CONTROL ARM) COULD BREAK WHERE IT IS MOUNTED TO THE FRAME.
Consequence & remedy
Consequence: THIS CAN CAUSE A KNOCKING SOUND AND ABNORMAL STEERING. THIS COULD RESULT IN DIFFICULTY CONTROLLING THE VEHICLE AND INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL REPLACE THE TRANSVERSE LINKS ON THE LEFT AND RIGHT SIDES WITH NEW ONES. OWNER NOTIFICATION BEGAN JULY 29, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT NISSAN AT 1-800-647-7261 OR INFINITI AT 1-800-662-6200.
Feb 12, 2002
ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH AN ELECTRONIC THROTTLE CONTROL SYSTEM, THE STOPPER FOR THE ACCELERATOR PEDAL WILL PREVENT EXCESSIVE MOVEMENT OF THE ACCELERATOR POSITION SENSOR. IF THE DRIVER APPLIES OVERLY EXCESSIVE FORCE TO THE ACCELERATOR PEDAL WHILE AT THE SAME TIME PUSHING IT TO THE RIGHT, THE PEDAL CAN "OVER TRAVEL" DUE TO THE DESIGN OF THE PEDAL STOPPER.
Consequence & remedy
Consequence: THIS WILL CAUSE THE ENGINE MALFUNCTION INDICATOR LAMP TO COME ON AND THE ENGINE SPEED TO BE SEVERELY LIMITED. IF THIS OCCURS UNEXPECTEDLY, IT COULD LEAD TO A CRASH.
Remedy: DEALERS WILL INSTALL A NEW ACCELERATOR PEDAL STOPPER. OWNER NOTIFICATION BEGAN MARCH 11, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT NISSAN AT 1-800-647-7261 OR INFINITI AT 800-662-6200.
Jan 11, 2002
ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A TRACTION CONTROL SYSTEM, THE ODOMETER IN THE SUBJECT VEHICLES REGISTERS DISTANCE IN KILOMETERS INSTEAD OF MILES AS IS SPECIFIED IN THE DESIGN. THE ODOMETER DOES NOT HAVE A LABEL THAT INDICATES "KILOMETERS" OR "KM" AS REQUIRED BY FMVSS NO. 101, "CONTROLS AND DISPLAYS."
Consequence & remedy
Consequence: Not supplied
Remedy: DEALERS WILL INSPECT THE ODOMETER TO DETERMINE IF IT IS CORRECT AND, IF NOT, WILL REPLACE THE SPEEDOMETER/ODOMETER ASSEMBLY. OWNER NOTIFICATION BEGAN DECEMBER 12, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT NISSAN AT 1-800-647-7261.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration