NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
56 reportsMileage unknown · Aug 17, 2026
Air Bags
The contact owns a 2010 Nissan Cube. The contact received notification of NHTSA Campaign Number: 26V230000 (Air Bags). The vehicle was taken to the dealer, where the contact was informed that the parts were ordered. The contact stated that the parts had not been available for approximately 62 days. The manufacturer was not conta…
Read full complaint
The contact owns a 2010 Nissan Cube. The contact received notification of NHTSA Campaign Number: 26V230000 (Air Bags). The vehicle was taken to the dealer, where the contact was informed that the parts were ordered. The contact stated that the parts had not been available for approximately 62 days. The manufacturer was not contacted. The contact had not experienced a failure.
NHTSA ODI #11757388
139,000 miles · Jun 23, 2026
Air Bags
The contact owns a 2010 Nissan Cube. The contact stated that upon taking the vehicle to the dealer to be repaired under NHTSA Campaign Number: 26V230000 (AIR BAGS), the dealer discovered that the vehicle was not equipped with a front driver's side air bag. The contact stated that the vehicle was purchased as a used vehicle from …
Read full complaint
The contact owns a 2010 Nissan Cube. The contact stated that upon taking the vehicle to the dealer to be repaired under NHTSA Campaign Number: 26V230000 (AIR BAGS), the dealer discovered that the vehicle was not equipped with a front driver's side air bag. The contact stated that the vehicle was purchased as a used vehicle from Marty Cancila Dodge Chrysler Jeep Ram (2175 N Hwy 67, Saint Louis, MO 63114); who had not disclosed that the vehicle was not equipped with the air bag. The Nissan dealer had ordered an air bag for the recall repair. The vehicle was not yet repaired. The failure mileage was 139,000.
NHTSA ODI #11746002
138,000 miles · Jun 10, 2026
Air BagsCrashInjury
The contact owned a 2010 Nissan Cube. The contact stated that while driving at 5 MPH at an intersection and making a left turn, the front passenger's side near the front bumper of the vehicle collided with another vehicle. The contact stated that all the air bags deployed, with the exception of the front driver's side air bag. T…
Read full complaint
The contact owned a 2010 Nissan Cube. The contact stated that while driving at 5 MPH at an intersection and making a left turn, the front passenger's side near the front bumper of the vehicle collided with another vehicle. The contact stated that all the air bags deployed, with the exception of the front driver's side air bag. The contact sustained a neck injury and a gash cut on his left leg near the calf. No medical attention was required. No police report was filed. The vehicle was towed to a salvage yard. The contact related the failure to NHTSA Campaign Number: 26V230000(AIRBAGS). The manufacturer was not notified of the failure. The approximate failure mileage was 138,000.
NHTSA ODI #11743331
Mileage unknown · Sep 20, 2024
Fuel System, Gasoline
The contact owns a 2010 Nissan Cube. The contact stated while the vehicle was parked, the contact noticed a strong fuel odor on the exterior and in the interior of the vehicle. The vehicle was taken to an independent mechanic where it was diagnosed with a cracked fuel tank filler neck. The contact was informed that the fuel tank…
Read full complaint
The contact owns a 2010 Nissan Cube. The contact stated while the vehicle was parked, the contact noticed a strong fuel odor on the exterior and in the interior of the vehicle. The vehicle was taken to an independent mechanic where it was diagnosed with a cracked fuel tank filler neck. The contact was informed that the fuel tank needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was unknown.
NHTSA ODI #11615619
Mileage unknown · Apr 10, 2023
Electrical SystemSteering
Problem is the anti theft module located on the steering column has malfunctioned for my wife’s 2010 Nissan Cube keyless ignition. Vehicle would not restart for my wife after sitting for 5 hours, luckily she was not way off somewhere. From what I’ve seen Nissan did a recall of a similar defective module on other models but did n…
Read full complaint
Problem is the anti theft module located on the steering column has malfunctioned for my wife’s 2010 Nissan Cube keyless ignition. Vehicle would not restart for my wife after sitting for 5 hours, luckily she was not way off somewhere. From what I’ve seen Nissan did a recall of a similar defective module on other models but did not include the Cube. Nissan doesn’t even have the parts readily available for repair. Vehicle has been sitting at a repair shop for over a month now. This should be a safety issue as it could leave people totally stranded in the middle of nowhere with no meaningful way to repair the vehicle. The part number of the module is 487001 FA0C. It is believed that Nissan did not recall the Cube because of the low quantity of vehicles manufactured in relation to the other problem models.
NHTSA ODI #11516327
Mileage unknown · Mar 14, 2023
Fuel/propulsion System
Fuel level readings have been erratic for over 40,000 miles now. Fuel gauge will randomly show the fuel level with less than 1/4 tank left, even though the car has gone less than 100 miles after filling (while the car can travel over 300 miles on a full tank.) Then a little while later, the fuel level will appear normal. And …
Read full complaint
Fuel level readings have been erratic for over 40,000 miles now. Fuel gauge will randomly show the fuel level with less than 1/4 tank left, even though the car has gone less than 100 miles after filling (while the car can travel over 300 miles on a full tank.) Then a little while later, the fuel level will appear normal. And this cycle will repeat many times before the tank is actually below 1/4 tank full, based on both mileage and the "normal" fuel level.
NHTSA ODI #11511688
Mileage unknown · Jun 15, 2022
Power Train
For a couple weeks on & off it’s been not wanting to go when I step on gas. I remember this doing same sort of thing before Allen web supposedly replaced my transmission as it was one of millions that are faulty as is one they put in 2018 only has 18,000 miles on tbis supposed replaced transmission & it’s in a mechanic shop as I…
Read full complaint
For a couple weeks on & off it’s been not wanting to go when I step on gas. I remember this doing same sort of thing before Allen web supposedly replaced my transmission as it was one of millions that are faulty as is one they put in 2018 only has 18,000 miles on tbis supposed replaced transmission & it’s in a mechanic shop as I write this a waiting on hopefully Nissan paying for this faulty transmission. I shouldn’t have to buy one when it’s only got 18,000 miles on it. I’ve almost been rear ended due to This ongoing problem. People behind me are ready to go when light turns green. I floor my gas pedal & it does nothing . Have to Hurry put my flashers on pray to God no one hits me & flag everyone to go around. I turn car off put I park first of course , wait few seconds & sometimes it thankfully goes into gear & i baby it rest of way as I don’t want to make it worse by flooring my gas pedal. I’m very careful & pray I make it rest my way to work or home whichever the case . I barely made it to work other day. My friend thankfully had my Nissan Cube towed to a shop as it turns out it in fact had all same codes as before they supposedly put newer one in P1778 p0868 P0725, p0746 & so on transmission CVT TRANSMISSION FAILURE! $2,935 plus other huge problem totaling $4,431 ! I definitely shouldn’t have to be dealing with any of this again!! I don’t drive far to work, had surgery as well so didn’t drive many places for a bit this is why only gone 18,000 miles in 4 years. I called auto mall Nissan & asked about my warranty they told me it’s expired! For only 18,000 miles put in it that’s ridiculous! Hwy robbery! Talk about a lemon again. Could of been smashed up by a truck being behind me a lot of things could of happened endangering myself as well as drivers behind me & behind those people. Plus dangerous being on side of road waiting to see if it’s gonna go into gear again or not! I understand things wear out but this transmission should be good thousands of miles!
NHTSA ODI #11469469
Mileage unknown · May 31, 2022
Visibility/wiper
I was washing my car by hand and I was washing the driver's side rear view mirror and pivoted it away from the normal position so I could clean it better. When put it back to it's normal position, the hinge broke. When I looked closely at the hinge, I noticed that the hinge pretty much disintegrated, so it was just a matter of t…
Read full complaint
I was washing my car by hand and I was washing the driver's side rear view mirror and pivoted it away from the normal position so I could clean it better. When put it back to it's normal position, the hinge broke. When I looked closely at the hinge, I noticed that the hinge pretty much disintegrated, so it was just a matter of time before it broke. It could've broken off on the highway and been blown off, possibly damaging the vehicle or another vehicle, as the mirror was only hanging by the wires at that point. Also you can't drive a car without a driver's side mirror. I removed the mirror after I got done washing the car, so it wouldn't fall off and hit the car. I then ordered replacements for both the driver's side and passenger's side outside mirrors, including both the plain matte black covers, and the pre-primed covers, as I don't have to rush in getting the pre-primed covers painted to match the covers on the old mirrors. I attached the invoice for the replacements. The invoice doesn't include the cost of having the covers painted. I don't think the probably needs somebody else to confirm it, as the mirror is clearly separated from the bracket. The passenger's side mirror is showing the signs of starting to disintegrate, and both mirrors are available for inspection. Nobody else has inspected the mirrors. I tried to let the manufacturer know about it, but my email to them was bounced back as undeliverable. There were no symptoms of the problem prior to failure. The pictures of the mirror on the workbench are of the driver's side mirror, while the pictures of the mirror on the car are of the passenger's side mirror. I also included a picture of the odometer reading.
NHTSA ODI #11466830
1,125,600 miles · Jul 17, 2020
Electrical SystemElectronic Stability Control (esc)Fuel/propulsion System
I SAW THAT IN PHOENIX AZ THE SAFETY RECALL BEGAN ON SEPTEMBER 13,2010 FOR FUEL SYSTEM, GASOLINE;STORAGE. REPORTED AN SAFTEY COMPLAINT ON JULY 16TH, 2020 11:45 PM PHOENIX AZ. ELECTIROCAL STABILITY CONTROL STARTED ON JUNE 10TH 2020 DIDN'T THINK MUCH OF IT CAR CUT OFF AT AN RED LIGHT I TURNED MY HAZARD LIGHTS ON PUT THE CAR IN PAR…
Read full complaint
I SAW THAT IN PHOENIX AZ THE SAFETY RECALL BEGAN ON SEPTEMBER 13,2010 FOR FUEL SYSTEM, GASOLINE;STORAGE. REPORTED AN SAFTEY COMPLAINT ON JULY 16TH, 2020 11:45 PM PHOENIX AZ. ELECTIROCAL STABILITY CONTROL STARTED ON JUNE 10TH 2020 DIDN'T THINK MUCH OF IT CAR CUT OFF AT AN RED LIGHT I TURNED MY HAZARD LIGHTS ON PUT THE CAR IN PARK AND STARTED THE CAR UP AGAIN. THIS HAPPENED AGAIN ON JULY 15TH 2020 TOOK IT IN TO THE DEALER( AUTO ACTION 1827 W BROADWAY RD) I PAY A CAR NOTE WITH TOLD THEM WHAT HAPPENED THEY SAID THEY NEEDED TO RUN IT TO SEE WHAT WAS GOING ON AND WOULD NOT PRESENT AND SPARE CAR FOR THE INCONVENIENCE OR HAD ANY CAR FAX ON HAND. JULY 16TH 2020 I NOTICED THAT OIL WAS INDEED LEAKING FROM THE BOTTOM OF THE CAR.
NHTSA ODI #11339860
65,909 miles · Feb 25, 2020
Electrical SystemSteeringUnknown Or Other
MY VEHICLE WOULD NOT START. I HAD TO HAVE IT TOWED TO MY MECHANIC WHERE HIS COMPUTER DIAGNOSTIC FOUND THE PROBLEM TO BE THE STEERING MODULE THAT STARTS THE VEHICLE. I HAD TO HAVE IT REPLACED AT MY COST OF $971.00. MY MECHANIC INFORMED ME THAT THIS SAME PROBLEM WAS PREVALENT IN THE YEAR PRIOR TO MINE AND THAT THEY WERE BEING REPA…
Read full complaint
MY VEHICLE WOULD NOT START. I HAD TO HAVE IT TOWED TO MY MECHANIC WHERE HIS COMPUTER DIAGNOSTIC FOUND THE PROBLEM TO BE THE STEERING MODULE THAT STARTS THE VEHICLE. I HAD TO HAVE IT REPLACED AT MY COST OF $971.00. MY MECHANIC INFORMED ME THAT THIS SAME PROBLEM WAS PREVALENT IN THE YEAR PRIOR TO MINE AND THAT THEY WERE BEING REPAIRED BY THE MANUFACTURER. I CONTACTED THE MANUFACTURER AND WAS TOLD THERE WAS NO CAMPAIGN FOR MY PARTICULAR VIN NUMBER. I DON'T UNDERSTAND WHY THE YEAR PRIOR TO MINE IS COVERED BUT MINE IS NOT. I AM THE ORIGINAL OWNER OF THE VEHICLE AND I HAVE HAD THIS VEHICLE SERVICED AS REQUIRED THROUGH THE DEALERSHIP ORIGINALLY, THEN CONTINUED BY MY MECHANIC. I WOULD LIKE TO FILE A COMPLAINT AGAINST THIS MANUFACTURER TO GET REIMBURSED FOR THIS DEFECT.
NHTSA ODI #11311450
NHTSA investigations
2PE25005 · Driver Airbag Inflator Rupture
Opened Jun 13, 2025 · Closed Sep 3, 2026
Status: closed (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module
The Office of Defects Investigation (ODI) opened Preliminary Evaluation PE25005 on June 13, 2025, to assess the scope, root cause, and potential defect in 2009 Model Year (MY) Nissan Cube vehicles equipped with Takata PSDI-X air bag inflators.At the time the investigation was opened, analysis by Nissan and Takata (now New Leaf LLC) indicated that a rupture occurred at a weld point between the inflator cap and housing in a 2009 MY Nissan Cube.Nissan ruled out the propellant degradation root cause characteristic of the larger, well known, Takata recall, and instead identified a welding root cause. On April 9, 2026, Nissan North America, Inc. submitted a Part 573 Safety Recall Report to address the weld defect.Recall 26V230 includes the 28,388 2009 MY vehicles identified in the opening resume for this investigation and expands the population to include 2010 MY Nissan Cube vehicles for a total population of 47,928 vehicles produced between October 10, 2008, and September 25, 2010.Nissan identified the driver’s front air bag inflator (Takata PSDI-X, Part Number 98560-7991C) produced by TK Services Inc. within a specific lot may contain an improper body weld seal to the inflator base. This improper weld can cause the air bag module to detach from the steering wheel during deployment, increasing the risk of injury to the occupant in the event of a crash. Dealers will inspect the serial number on the driver’s air bag inflator in recalled vehicles to identify the air bag inflator lot. If the inflator is part of the affected lot, the dealer will remove and replace it with a new inflator manufactured by a different supplier. This repair will be performed free of charge. See NHTSA Recall No. 26V230 for further details. Based on Nissan's recall action, this Preliminary Evaluation is closed.
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.