IllustrationSun visor part number 96401-9HT2A needs replaced and Nissan has not had any available for this past year.
2017 Nissan Altima
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2017 Nissan Altima do not stand out strongly from the model-year median of 231.
About this comparison →How this year compares
Owner complaints by model year
Compare all Altima years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
380–25K
3325–50K
4950–75K
2775–100K
14100–150K
4150K+
165 reports with mileage · 226 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 133 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 73 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Vehicle Speed Control. Review the 41 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
24 crash reports7 fire reports19 injury reports
Unknown Or Other complaints
62 reportsMy Nissan was bought Used. It has no damages and it drives well. I was told it was in an accident that affected the right side. The doors were replaced.
Was driving and when we stopped and was ready to pull out the car wouldn’t move. The gas pedal was all the way to the floor after several seconds it shot across the road a then wouldn’t get above 20 mph. The rpm gauge shot all the way, pegged out. Drove for a few miles and pulled over. Turned the car off and then it took off jus…
Read full complaint
Was driving and when we stopped and was ready to pull out the car wouldn’t move. The gas pedal was all the way to the floor after several seconds it shot across the road a then wouldn’t get above 20 mph. The rpm gauge shot all the way, pegged out. Drove for a few miles and pulled over. Turned the car off and then it took off just fine. Shortly afterwards it bogged down again and would get over 20mph again. Something needs to be fixed right away
Transmission: this is the 2nd transmission in about 22,000 miles. Car will start to stall out and then high rev the rpm’s. This has caused significant power loss suddenly in traffic. Issue has been recreated by mechanic and has been inspected thoroughly. Previously transmission was rebuilt with the torque converter being replac…
Read full complaint
Transmission: this is the 2nd transmission in about 22,000 miles. Car will start to stall out and then high rev the rpm’s. This has caused significant power loss suddenly in traffic. Issue has been recreated by mechanic and has been inspected thoroughly. Previously transmission was rebuilt with the torque converter being replaced. No indicator lights have come on prior or during sudden loss, only check engine light once. Shutting off vehicle for approximately 5 or so minutes resolves the issue but only for a limited amount of time.
Check Engine light is on and has been diagnosed twice at different Nissan dealerships. Once the car stops, it hesitates to accelerate. I have to press the gas more than once and then it zooms off. Cleaning the Mass Air Flow Sensor and Throttle Body worked for 3 days and light went out. I am back were I started with slower acc…
Read full complaint
Check Engine light is on and has been diagnosed twice at different Nissan dealerships. Once the car stops, it hesitates to accelerate. I have to press the gas more than once and then it zooms off. Cleaning the Mass Air Flow Sensor and Throttle Body worked for 3 days and light went out. I am back were I started with slower acceleration than before. Today I drove with my emergency flashers, after cars started honking at me for not moving. I have 3 kids with me most of the time and fear being rear ended. The car is being towed back to the dealership since its no longer safe to drive. This is a Safety Hazard due to the possibility of being rear-ended.
The inspection i change lamps the head light 2023 this year my car Still no warning the police officer
When I am driving this vehicle, I get to a stop sign or red light or even stopping at a drive-through window and when I need to go the car will not accelerate I have to shut the car off and turn it back on to get it to accelerate and go. This keeps happening and is very dangerous especially when I have my children in the car. Th…
Read full complaint
When I am driving this vehicle, I get to a stop sign or red light or even stopping at a drive-through window and when I need to go the car will not accelerate I have to shut the car off and turn it back on to get it to accelerate and go. This keeps happening and is very dangerous especially when I have my children in the car. The car also has trouble shifting into gear and jerks when I get onto the hwy. The car dealership last year told me it was nothing that they could not locate any issue with the vehicle. No symptoms prior to failure of the car sometimes it does it and sometimes it doesn't
I experienced My 2017 Nissan Altima having a delay accelerating after I stop at lights then it took a couple of seconds of my foot pushing down on gas petal to get going with it taking off very fast! It happened 3 times in a 2 week timeframe, then on Sunday, 9/17/2023 my daughter was driving and I was the passenger and it happ…
Read full complaint
I experienced My 2017 Nissan Altima having a delay accelerating after I stop at lights then it took a couple of seconds of my foot pushing down on gas petal to get going with it taking off very fast! It happened 3 times in a 2 week timeframe, then on Sunday, 9/17/2023 my daughter was driving and I was the passenger and it happened 4 separate times in 1 hour! I took it into Nissan in Salem, NH , (where I purchased the vehicle), on 9/18/23 and it isn’t giving a Code so they say they can’t fix it until they get a code by replicating it! That is unacceptable because it happens sporadically so unless you give me a loaner car so they can drive it all the time that to see it happen. So right now my car is at that service place! I need a “loaner car” and for Nissan to FIX this problem NOW or I will be force to file a lawsuit and I will make sure everyone I know doesn’t buy a Nissan!
I got this car 2 weeks ago and 4 days after i got it, I was driving on the free way when it started lunging forward and slowing down. There was a car behind me that almost hit me because the car was malfunctioning. This problem caused danger to me and others on the road.
Nissan has a very serious safety concern that if not remedied I will have to take action elsewhere. My 2017 altima lags and sputters randomly. I was almost hit today when I turned from an intersection and the car slowed down in the middle of the intersection. I demand more information about this issue and how to fix it within re…
Read full complaint
Nissan has a very serious safety concern that if not remedied I will have to take action elsewhere. My 2017 altima lags and sputters randomly. I was almost hit today when I turned from an intersection and the car slowed down in the middle of the intersection. I demand more information about this issue and how to fix it within reasonable price range. The dealer couldn't find a problem. This is a huge problem that could cost many people their lives and money I do not have right now.
Official recalls
320V315000 · Latches/locks/linkages:hood:latch
May 28, 2020
Nissan North America, Inc. (Nissan) is recalling certain model year 2013-2018 Nissan Altima vehicles. If the primary hood latch is inadvertently released, there is an increased likelihood that the secondary hood latch may corrode over time.
Consequence & remedy
Consequence: Corrosion to the secondary latch may cause it to bind and remain in the unlatched position when the hood is closed. If the primary latch is inadvertently released again and the secondary latch is not engaged, the hood could unexpectedly open while driving, increasing the risk of a vehicle crash.
Remedy: Nissan will notify owners, and dealers will install a stronger release spring in the hood release lever, a warning label near the secondary hood latch, and an Owners Manual addendum card with instructions on how to lubricate and maintain the secondary hood latch mechanism, free of charge. Owner notification letters were mailed June 30, 2021. Owners may contact Nissan customer service at 1-800-867-7669. Note: Recall 16V-029 remains open for any unremedied 2013-2015 Altimas and this recall applies to all vehicles covered by 16V-029 even if those repairs have already been performed.
18V915000 · Latches/locks/linkages:doors:latch; Structure:emergency:escape/egress/exit
Dec 19, 2018
Nissan North America, Inc. (Nissan) is recalling certain 2015-2017 Altima vehicles, previously remedied under recall number 17V-040. The door latch-lock cable may not have been routed properly in the rear door when the remedy was applied. As a result, the cable may interfere with the window regulator causing the rear passenger door to unlatch and inadvertently open without warning when the window is lowered.
Consequence & remedy
Consequence: If the rear passenger door opens while the vehicle is moving, the rear passengers have an increased risk of injury.
Remedy: Nissan will notify owners, and dealers will secure the latch-lock cables in the correct position using the new remedy procedure, free of charge. The recall began February 5, 2019. Owners may contact Nissan customer service at 1-800-647-7669.
Additional source detail variants (2)
Structure:emergency:escape/egress/exit
Nissan North America, Inc. (Nissan) is recalling certain 2015-2017 Altima vehicles, previously remedied under recall number 17V-040. The door latch-lock cable may not have been routed properly in the rear door when the remedy was applied. As a result, the cable may interfere with the window regulator causing the rear passenger door to unlatch and inadvertently open without warning when the window is lowered.
Consequence: If the rear passenger door opens while the vehicle is moving, the rear passengers have an increased risk of injury.
Remedy: Nissan will notify owners, and dealers will secure the latch-lock cables in the correct position using the new remedy procedure, free of charge. The recall began February 5, 2019. Owners may contact Nissan customer service at 1-800-647-7669.
Latches/locks/linkages:doors:latch
Nissan North America, Inc. (Nissan) is recalling certain 2015-2017 Altima vehicles, previously remedied under recall number 17V-040. The door latch-lock cable may not have been routed properly in the rear door when the remedy was applied. As a result, the cable may interfere with the window regulator causing the rear passenger door to unlatch and inadvertently open without warning when the window is lowered.
Consequence: If the rear passenger door opens while the vehicle is moving, the rear passengers have an increased risk of injury.
Remedy: Nissan will notify owners, and dealers will secure the latch-lock cables in the correct position using the new remedy procedure, free of charge. The recall began February 5, 2019. Owners may contact Nissan customer service at 1-800-647-7669.
17V040000 · Latches/locks/linkages:doors:latch
Jan 18, 2017
Nissan North America, Inc. (Nissan) is recalling certain 2015-2017 Altima vehicles. The rear door latch/lock cable on the vehicles may have been improperly routed. As a result, lowering a rear window may inadvertently cause that door to unlatch and open.
Consequence & remedy
Consequence: If the rear passenger doors inadvertently open while the vehicle is in motion, it may increase the risk of injury to the rear passengers.
Remedy: Nissan will notify owners, and dealers will correct the rear door latch/lock cable routing, free of charge. The recall began on February 16, 2017. Owners may contact Nissan customer service at 1-800-647-7261.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA19002 · Rear Suspension Control Arm Failure
Opened Jul 29, 2019 · Closed Jun 16, 2025
Status: closed (inferred from source dates) · Suspension:rear
On July 29, 2019, the Office of Defects Investigation (ODI) opened EA19002 to investigate instances of alleged rear lower control arm failures in 2013-2018 Nissan Altima and 2016-2018 Nissan Maxima vehicles. At the time the investigation was opened ODI had 91 consumer complaints alleging rear lower control arm failures in the subject vehicles.ODI was concerned about these complaints because many of them alleged an increased steering effort or loss of vehicle control.At the time these complaints were received, ODI was also aware of a proactive service campaign addressing 2013 Nissan Altima in salt-belt states for a similar concern. Since opening the investigation, ODI has confirmed, based on consumer complaints, warranty data, and testing conducted by Nissan and ODI, that owners of the subject vehicles are experiencing a corroded bushing at one of three mounting points of the control arm to the rear subframe.ODI has also confirmed that drivers become aware of the problem because of sound and abnormal vibrations. In addition, the failure mileage is typically over 113,000 miles at the time of failure.In conjunction with Nissan and VRTC, ODI participated in testing to assess the potential safety consequence of a bushing failure.It was found the Vehicle Dynamic Control system allows the driver to maintain vehicle control in the event of a bushing failure.With between 7 to 13 years of field exposure, ODI is aware of only one low speed crash allegation describing minor contact with another vehicle’s trailer hitch. Nissan acknowledges that a crack can develop in affected control arms due to stress loading from normal use and that salts commonly used for roadway snow and ice treatment may result in corrosion that exacerbates the progression of the crack.Nissan implemented a design change in January of 2018 to improve the durability of the lower control arm.Affected vehicles have either been repaired with the countermeasure part under a customer satisfaction campaign or been provided a warranty extension from 3 years/36,000 miles to 10 year/unlimited mileage. Through testing and analysis of the information obtained to date, ODI has not identified a defect representing an unreasonable risk to motor vehicle safety involving corrosion of the subject rear lower control arm at this time.With a declining trend of reports and Nissan’s actions to implement a countermeasure and extended warranty coverage, further investigation of the issue does not appear to be warranted at this time.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov. A detailed discussion of the investigation and related complaint numbers can be viewed in the attached closing report.
PE18013 · Rear Suspension Control Arm Failure
Opened Dec 1, 2018 · Closed Aug 21, 2019
Status: closed (inferred from source dates) · Suspension:rear
PE18-013 was opened on December 1, 2018, with 4 complaints to ODI alleging incidents of the lower control arm fracturing at a connection point to the vehicle chassis due to corrosion. ODI has received an additional 87 complaints since the PE was opened. During PE18-013, Nissan indicated model years 2013-2018 shared a common rear lower control arm design. Nissan provided complaint and warranty data regarding 48 incidents of the subject failure. The majority of the complaints are from vehicles registered in salt belt states. There have been no crashes, injuries, or fatalities confirmed as of this date. Nissan advised that it has conducted testing to assess safety risk. Nissan states that due to low incident rate, high detectability, and low risk of adverse vehicle dynamics, it does not believe the subject lower control arm failure poses an unreasonable risk to motor vehicle safety.This preliminary evaluation has been upgraded to Engineering Analysis (EA) 19-002. During the EA, ODI will continue to collect and analyze complaint and field data in its efforts to fully assess the scope and frequency of the alleged defect. More importantly, ODI will also seek additional information and data regarding the potential safety consequences of rear lower control arm failure, both from evidence collected from field failures and through more rigorous and comprehensive vehicle testing to be conducted by either Nissan and/or NHTSA.The ODI reports (VOQs) cited above can be viewed at NHTSA.gov under the following reference numbers: 11234334, 11234232, 11234189, 11233771, 11233234, 11232381, 11231589, 11230323, 11230184, 11229023, 11229003, 11228730, 11228651, 11228631, 11228625, 11223086, 11222602, 11222427, 11222303, 11221802, 11219943, 11217980, 11217542, 11217505, 11217290, 11210699, 11209647, 11208580, 11208274, 11207545, 11206310, 11205711, 11205461, 11203864, 11203005, 11195416, 11193545, 11193020, 11192269, 11192066, 11191270, 11191207, 11191185, 11191042, 11190360, 11190323, 11187334, 11187157, 11186747, 11186195, 11185664, 11185632, 11185589, 11183799, 11183295, 11183198, 11182705,11182528, 11182265, 11182137, 11182088, 11181373, 11181223, 11181155, 11181009, 11180126, 11176565, 11176261, 11176135, 11175821, 11172604, 11172200, 11172065, 11170019, 11169930, 11165194, 11163833, 11163489, 11162559, 11162195, 11161956, 11161497, 11161117, 11157323, 11157234, 11156772, 11141169, 11139516, 11129476, 11122829, 11114374.