IllustrationMy vehicle stalls whenever I am stopped, and will not move , then it accelerate really fast, sometimes it loses speeds in which I can not accelerate the vehicle. I have taken this vehicle to 3 mechanical shops and no can tell me what the problem is. I have had this problem since I purchased the vehicle.
2016 Nissan Altima
Owner reports · Recalls · Investigations
More warning signs than most Altima years
Owner complaints for the 2016 Nissan Altima are substantially higher than the model-year median of 231.
About this comparison →How this year compares
Owner complaints by model year
Compare all Altima years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
480–25K
6925–50K
8750–75K
5475–100K
31100–150K
6150K+
295 reports with mileage · 258 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 235 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 86 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 70 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
28 crash reports3 fire reports17 injury reports
Vehicle Speed Control complaints
65 reportsThe car hesitates accelerating. After coming to a complete stop, when the gas pedal is pressed, the car will not go. This happens after in town driving for about 20 min or so when it stops and goes, stops and goes. The gas pedal will be pressed and the rpms will be going up but the car just sits there until all of a sudden takin…
Read full complaint
The car hesitates accelerating. After coming to a complete stop, when the gas pedal is pressed, the car will not go. This happens after in town driving for about 20 min or so when it stops and goes, stops and goes. The gas pedal will be pressed and the rpms will be going up but the car just sits there until all of a sudden taking off. No warnings appear. I explained issues to service techs at Nissan and they were able to replicate it and attempted to repair but it is doing it again less than a month later. It has been very dangerous especially when trying to merge into oncoming traffic.
The contact owns a 2016 Nissan Altima. The contact stated that while driving at an undisclosed speed, the vehicle failed to accelerate and instead decelerated. On another occasion while driving approximately 20-30 MPH, the vehicle was jerking with an abnormal ticking sound. The check engine warning light illuminated. The vehicle…
Read full complaint
The contact owns a 2016 Nissan Altima. The contact stated that while driving at an undisclosed speed, the vehicle failed to accelerate and instead decelerated. On another occasion while driving approximately 20-30 MPH, the vehicle was jerking with an abnormal ticking sound. The check engine warning light illuminated. The vehicle was taken to the local dealer but the vehicle was not diagnosed or repaired. The vehicle was taken to an independent mechanic and diagnosed with transmission failure. The manufacturer was not notified of the failure. The failure mileage was approximately 84,000.
2016 Nissan Altima 29,000 MILES! FAULTY TRANSMISSION! Why hasn’t a RECALL been issued? Nissan dealership informed me that I will have to replace the transmission! This will cost me $4,500.00
While trying to pull out of a intersection, car will not move or will move very slowly. I have almost been t-boned twice with my family in the car. This happens intermittently, 4 times in the past year. After car is turned off and restarted the issue seems to go away until the next time. The needs to be a safety recall befo…
Read full complaint
While trying to pull out of a intersection, car will not move or will move very slowly. I have almost been t-boned twice with my family in the car. This happens intermittently, 4 times in the past year. After car is turned off and restarted the issue seems to go away until the next time. The needs to be a safety recall before someone gets seriously hurt.
The car stalls out when driving. Gas is engaged but car will not move. Jerks, bumps. Within a few seconds, car resumes movements but jerks.
I just purchased this vehicle with 93,000 miles and good condition. A warning or indicator light never comes on but sporadically I will be driving around 40-50mph & if I let off of the gas something happens where no matter how hard or fast I press the accelerator the car looses power. I can press the accelerator all the way to t…
Read full complaint
I just purchased this vehicle with 93,000 miles and good condition. A warning or indicator light never comes on but sporadically I will be driving around 40-50mph & if I let off of the gas something happens where no matter how hard or fast I press the accelerator the car looses power. I can press the accelerator all the way to the floor & still not speed up. The car will slowly decrease speed until about 30mph or either I have to take my foot off of the accelerator totally & press hard about 1/4 on the accelerator to regain power. It feels like the pressure behind the accelerator disappears when all of this happens. There is no dimming of lights or anything obvious. It happens when my Mom drives also. I have lost power trying to pass a car or turn with oncoming traffic ahead. It scares me.
The transmission has fail it accelerates on its own,jerking,hesitated
I have had this 2016 Nissan Altima SR for the past 5 years (1st owner) and it just began giving me acceleration issues about 2 months ago. At random times, while at a stop, reversing, doing a u-turn or changing gears, I step on the accelerator and it will not move. I have pushed all the way down on the accelerator and it won't b…
Read full complaint
I have had this 2016 Nissan Altima SR for the past 5 years (1st owner) and it just began giving me acceleration issues about 2 months ago. At random times, while at a stop, reversing, doing a u-turn or changing gears, I step on the accelerator and it will not move. I have pushed all the way down on the accelerator and it won't budge for about 10 seconds, until then, it will just throw itself at a really high speed. There is no warning or light on the dashboard stating something is wrong. It does it at random times. There have been numerous times were I have been put at risk of a car accident because of this issue. Once, I was at a green light waiting to make a left, and when I had a chance to turn before the oncoming cars, I went for it, only to have the accelerator not work and go REALLY slowly (as if it was on neutral). At that speed, I was midway and the oncoming car was honking at me as it was getting closer. I kept stepping on the accelerator and nothing would happen. Luckily, a few seconds later it threw itself to a really high speed and I was able to make it before the oncoming car hit me. I have taken it to the dealer, only to find out I would be charged $169 for a diagnostics test and even then they wouldn't guarantee anything because it doesn't have any kind of warning light on the dashboard. The dealer then stated it could possibly be the transmission or throttle body. How is it possible for me to waste so much money on something the dealer itself is so unsure of the results? How can they guarantee they can fix the issue without happening again and possibly getting into an accident? I have heard of other Altima owners who have been told it is the transmission and they change it, only to have the same problems all over again. This issue really needs to be looked at before it gets more serious and cause devastating accidents. Thankfully it has not done that to me on the fwy yet.
Upon arriving to my grandson's daycare, I applied by brake and put my car in park and suddenly my car accelerated at a fast speed. My car moved forward across an area that the children are usually playing in, but because it was raining they were inside. Thank God! I can't even imagine what would have happened. My car finally…
Read full complaint
Upon arriving to my grandson's daycare, I applied by brake and put my car in park and suddenly my car accelerated at a fast speed. My car moved forward across an area that the children are usually playing in, but because it was raining they were inside. Thank God! I can't even imagine what would have happened. My car finally stopped because I was trying to avoid the daycare's shed, but hit the corner of the shed and this stopped the car. The air bag did not deploy as well. I am thankful to be alive and unharmed, but most thankful that no one else was harmed. My husband took photos of the brake marks on the pavement and grass and of the vehicle after collision with the shed and showing it was in park.
Official recalls
420V315000 · Latches/locks/linkages:hood:latch
May 28, 2020
Nissan North America, Inc. (Nissan) is recalling certain model year 2013-2018 Nissan Altima vehicles. If the primary hood latch is inadvertently released, there is an increased likelihood that the secondary hood latch may corrode over time.
Consequence & remedy
Consequence: Corrosion to the secondary latch may cause it to bind and remain in the unlatched position when the hood is closed. If the primary latch is inadvertently released again and the secondary latch is not engaged, the hood could unexpectedly open while driving, increasing the risk of a vehicle crash.
Remedy: Nissan will notify owners, and dealers will install a stronger release spring in the hood release lever, a warning label near the secondary hood latch, and an Owners Manual addendum card with instructions on how to lubricate and maintain the secondary hood latch mechanism, free of charge. Owner notification letters were mailed June 30, 2021. Owners may contact Nissan customer service at 1-800-867-7669. Note: Recall 16V-029 remains open for any unremedied 2013-2015 Altimas and this recall applies to all vehicles covered by 16V-029 even if those repairs have already been performed.
18V915000 · Latches/locks/linkages:doors:latch; Structure:emergency:escape/egress/exit
Dec 19, 2018
Nissan North America, Inc. (Nissan) is recalling certain 2015-2017 Altima vehicles, previously remedied under recall number 17V-040. The door latch-lock cable may not have been routed properly in the rear door when the remedy was applied. As a result, the cable may interfere with the window regulator causing the rear passenger door to unlatch and inadvertently open without warning when the window is lowered.
Consequence & remedy
Consequence: If the rear passenger door opens while the vehicle is moving, the rear passengers have an increased risk of injury.
Remedy: Nissan will notify owners, and dealers will secure the latch-lock cables in the correct position using the new remedy procedure, free of charge. The recall began February 5, 2019. Owners may contact Nissan customer service at 1-800-647-7669.
Additional source detail variants (2)
Structure:emergency:escape/egress/exit
Nissan North America, Inc. (Nissan) is recalling certain 2015-2017 Altima vehicles, previously remedied under recall number 17V-040. The door latch-lock cable may not have been routed properly in the rear door when the remedy was applied. As a result, the cable may interfere with the window regulator causing the rear passenger door to unlatch and inadvertently open without warning when the window is lowered.
Consequence: If the rear passenger door opens while the vehicle is moving, the rear passengers have an increased risk of injury.
Remedy: Nissan will notify owners, and dealers will secure the latch-lock cables in the correct position using the new remedy procedure, free of charge. The recall began February 5, 2019. Owners may contact Nissan customer service at 1-800-647-7669.
Latches/locks/linkages:doors:latch
Nissan North America, Inc. (Nissan) is recalling certain 2015-2017 Altima vehicles, previously remedied under recall number 17V-040. The door latch-lock cable may not have been routed properly in the rear door when the remedy was applied. As a result, the cable may interfere with the window regulator causing the rear passenger door to unlatch and inadvertently open without warning when the window is lowered.
Consequence: If the rear passenger door opens while the vehicle is moving, the rear passengers have an increased risk of injury.
Remedy: Nissan will notify owners, and dealers will secure the latch-lock cables in the correct position using the new remedy procedure, free of charge. The recall began February 5, 2019. Owners may contact Nissan customer service at 1-800-647-7669.
17V040000 · Latches/locks/linkages:doors:latch
Jan 18, 2017
Nissan North America, Inc. (Nissan) is recalling certain 2015-2017 Altima vehicles. The rear door latch/lock cable on the vehicles may have been improperly routed. As a result, lowering a rear window may inadvertently cause that door to unlatch and open.
Consequence & remedy
Consequence: If the rear passenger doors inadvertently open while the vehicle is in motion, it may increase the risk of injury to the rear passengers.
Remedy: Nissan will notify owners, and dealers will correct the rear door latch/lock cable routing, free of charge. The recall began on February 16, 2017. Owners may contact Nissan customer service at 1-800-647-7261.
16V244000 · Air Bags:sensor:occupant Classification
Apr 26, 2016
Nissan North America, Inc. (Nissan) is recalling certain model year 2016-2017 Nissan Maxima, 2013-2016 Nissan Altima, NV200, LEAF, Sentra, and Pathfinder, 2014-2016 Nissan NV200 Taxi, Infiniti QX60, QX60 Hybrid, and Q50 Hybrid, 2014-2017 Nissan Rogue and Infiniti Q50, 2015-2016 Nissan Murano, Murano Hybrid, and Chevrolet City Express, 2014-2015 Nissan Pathfinder Hybrid, and 2013 Infiniti JX35 vehicles. In these vehicles, the front seat passenger Occupant Classification System (OCS) may incorrectly classify an adult passenger as a child or classify the seat as empty despite it being occupied. As a result, the passenger frontal air bag may be turned off and not deploy in the event of a crash.
Consequence & remedy
Consequence: If the passenger frontal air bag does not deploy as intended in the event of a crash, the passenger is at an increased risk of injury.
Remedy: Nissan will notify their owners. Chevrolet City Express owners will be notified by General Motors. Dealers will reprogram the Air Bag Control Unit (ACU) and OCS Electronic Control Unit (ECU) in Altima, Maxima, Murano, Rogue, and Sentra vehicles, and replace the OCS ECU in LEAF, NV200, NV200 Taxi, Pathfinder, Infiniti Q50, JX35, and QX60 and Chevrolet City Express vehicles, free of charge. Interim notices were sent to owners on May 31, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Nissan customer service at 1-800-867-7669, Infiniti customer service at 1-888-833-3216 or Chevrolet customer service at 1-800-222-1020.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA19002 · Rear Suspension Control Arm Failure
Opened Jul 29, 2019 · Closed Jun 16, 2025
Status: closed (inferred from source dates) · Suspension:rear
On July 29, 2019, the Office of Defects Investigation (ODI) opened EA19002 to investigate instances of alleged rear lower control arm failures in 2013-2018 Nissan Altima and 2016-2018 Nissan Maxima vehicles. At the time the investigation was opened ODI had 91 consumer complaints alleging rear lower control arm failures in the subject vehicles.ODI was concerned about these complaints because many of them alleged an increased steering effort or loss of vehicle control.At the time these complaints were received, ODI was also aware of a proactive service campaign addressing 2013 Nissan Altima in salt-belt states for a similar concern. Since opening the investigation, ODI has confirmed, based on consumer complaints, warranty data, and testing conducted by Nissan and ODI, that owners of the subject vehicles are experiencing a corroded bushing at one of three mounting points of the control arm to the rear subframe.ODI has also confirmed that drivers become aware of the problem because of sound and abnormal vibrations. In addition, the failure mileage is typically over 113,000 miles at the time of failure.In conjunction with Nissan and VRTC, ODI participated in testing to assess the potential safety consequence of a bushing failure.It was found the Vehicle Dynamic Control system allows the driver to maintain vehicle control in the event of a bushing failure.With between 7 to 13 years of field exposure, ODI is aware of only one low speed crash allegation describing minor contact with another vehicle’s trailer hitch. Nissan acknowledges that a crack can develop in affected control arms due to stress loading from normal use and that salts commonly used for roadway snow and ice treatment may result in corrosion that exacerbates the progression of the crack.Nissan implemented a design change in January of 2018 to improve the durability of the lower control arm.Affected vehicles have either been repaired with the countermeasure part under a customer satisfaction campaign or been provided a warranty extension from 3 years/36,000 miles to 10 year/unlimited mileage. Through testing and analysis of the information obtained to date, ODI has not identified a defect representing an unreasonable risk to motor vehicle safety involving corrosion of the subject rear lower control arm at this time.With a declining trend of reports and Nissan’s actions to implement a countermeasure and extended warranty coverage, further investigation of the issue does not appear to be warranted at this time.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov. A detailed discussion of the investigation and related complaint numbers can be viewed in the attached closing report.
PE18013 · Rear Suspension Control Arm Failure
Opened Dec 1, 2018 · Closed Aug 21, 2019
Status: closed (inferred from source dates) · Suspension:rear
PE18-013 was opened on December 1, 2018, with 4 complaints to ODI alleging incidents of the lower control arm fracturing at a connection point to the vehicle chassis due to corrosion. ODI has received an additional 87 complaints since the PE was opened. During PE18-013, Nissan indicated model years 2013-2018 shared a common rear lower control arm design. Nissan provided complaint and warranty data regarding 48 incidents of the subject failure. The majority of the complaints are from vehicles registered in salt belt states. There have been no crashes, injuries, or fatalities confirmed as of this date. Nissan advised that it has conducted testing to assess safety risk. Nissan states that due to low incident rate, high detectability, and low risk of adverse vehicle dynamics, it does not believe the subject lower control arm failure poses an unreasonable risk to motor vehicle safety.This preliminary evaluation has been upgraded to Engineering Analysis (EA) 19-002. During the EA, ODI will continue to collect and analyze complaint and field data in its efforts to fully assess the scope and frequency of the alleged defect. More importantly, ODI will also seek additional information and data regarding the potential safety consequences of rear lower control arm failure, both from evidence collected from field failures and through more rigorous and comprehensive vehicle testing to be conducted by either Nissan and/or NHTSA.The ODI reports (VOQs) cited above can be viewed at NHTSA.gov under the following reference numbers: 11234334, 11234232, 11234189, 11233771, 11233234, 11232381, 11231589, 11230323, 11230184, 11229023, 11229003, 11228730, 11228651, 11228631, 11228625, 11223086, 11222602, 11222427, 11222303, 11221802, 11219943, 11217980, 11217542, 11217505, 11217290, 11210699, 11209647, 11208580, 11208274, 11207545, 11206310, 11205711, 11205461, 11203864, 11203005, 11195416, 11193545, 11193020, 11192269, 11192066, 11191270, 11191207, 11191185, 11191042, 11190360, 11190323, 11187334, 11187157, 11186747, 11186195, 11185664, 11185632, 11185589, 11183799, 11183295, 11183198, 11182705,11182528, 11182265, 11182137, 11182088, 11181373, 11181223, 11181155, 11181009, 11180126, 11176565, 11176261, 11176135, 11175821, 11172604, 11172200, 11172065, 11170019, 11169930, 11165194, 11163833, 11163489, 11162559, 11162195, 11161956, 11161497, 11161117, 11157323, 11157234, 11156772, 11141169, 11139516, 11129476, 11122829, 11114374.