IllustrationBACK IN JULY CAR STARTED TO LOSE POWER AND SPUTTER WHILE DRIVING, AND NISSAN REPLACED VALVE BODY. HOWEVER, CAR SHUT OFF WHILE DRIVING ON 09/07 AND I WAS ABLE TO COAST CAR TO CURB. WHEN TRYING TO START AGAIN, ENGINE WOULD ONLY CRANK AND NOT TURN OVER.
2015 Nissan Altima
Owner reports · Recalls · Investigations
More warning signs than most Altima years
Owner complaints for the 2015 Nissan Altima are substantially higher than the model-year median of 231.
About this comparison →How this year compares
Owner complaints by model year
Compare all Altima years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1330–25K
10425–50K
12950–75K
8675–100K
75100–150K
17150K+
544 reports with mileage · 408 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Exterior Lighting. Review the 269 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 177 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 161 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
46 crash reports5 fire reports25 injury reports
What owners actually said
952 reportsTL* THE CONTACT OWNS A 2015 NISSAN ALTIMA. THE CONTACT STATED THAT THE BRAKES MADE A LOUD SCREECHING NOISE WHEN THE BRAKE PEDAL WAS DEPRESSED. THE VEHICLE JERKED AND STOPPED QUICKLY REGARDLESS OF THE AMOUNT OF PRESSURE TO THE BRAKE PEDAL. THE DEALER DIAGNOSED THAT THE BRAKE PADS FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS …
Read full complaint
TL* THE CONTACT OWNS A 2015 NISSAN ALTIMA. THE CONTACT STATED THAT THE BRAKES MADE A LOUD SCREECHING NOISE WHEN THE BRAKE PEDAL WAS DEPRESSED. THE VEHICLE JERKED AND STOPPED QUICKLY REGARDLESS OF THE AMOUNT OF PRESSURE TO THE BRAKE PEDAL. THE DEALER DIAGNOSED THAT THE BRAKE PADS FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE FAILURE RECURRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 39,000.
WHILE PRESSING GAS MY RPM GOES UP AND DOWN REALLY FAST EVEN WHEN I'M AT A STEADY PACE, THE VEHICLE VIBRATES AND JERKS WHILE AND MOTION AND HAS SHUT OFF TWICE WHILE DRIVING. THE VIBRATION OCCURS WHILE IN MOTION. ONCE WHILE DRIVING THE CAR WOULDN'T DRIVE OVER 20MPH THEN IT SHUT OFF. OFTEN TIMES WHEN I MAKE A COMPLETE STOP THEN PRO…
Read full complaint
WHILE PRESSING GAS MY RPM GOES UP AND DOWN REALLY FAST EVEN WHEN I'M AT A STEADY PACE, THE VEHICLE VIBRATES AND JERKS WHILE AND MOTION AND HAS SHUT OFF TWICE WHILE DRIVING. THE VIBRATION OCCURS WHILE IN MOTION. ONCE WHILE DRIVING THE CAR WOULDN'T DRIVE OVER 20MPH THEN IT SHUT OFF. OFTEN TIMES WHEN I MAKE A COMPLETE STOP THEN PROCEED TO GO THE VEHICLE DOES A HARD JERK. THIS HAS BEEN GOING ON FOR SEVERAL MONTHS. I'VE CONTACTED NISSAN AND THEY HAVE DONE NOTHING TO ASSIST DESPITE THE FACT THAT I NOTICE ON DIFFERENT FORUMS LOTS OF PEOPLE COMPLAINING ABOUT THE EXACT SAME ISSUE STARTING WITH THE 2013 MODEL AND 2015. THIS CAR IS DANGEROUS AND CAN REALLY BECOME DEADLY FOR CONSUMERS WHILE RANDOMLY SHUTTING OFF WHILE IN MOTION. I PURCHASED MY VEHICLE WITH 13000 MILES AND NOW ITS AT 25000 THEIRS NO REASON THOUSANDS OF OTHERS SHOULD BE COMPLAINING ABOUT THE SAME ISSUE WITH THE EXACT MODEL AS MINE. THIS ISSUE HAS BEEN GOING ON FOR MONTHS NOW.
I WAS DRIVING MY 2015 ALTIMA ON A HIGHWAY AND THE CAR SUDDENLY STOPPED AS IN A STALL WITH CARS BEHIND ME SWERVING OFF THE HIGHWAY TO AVOID HITTING ME. THE CAR HAD ON OIL AND THE OIL WARNING LIGHT DID NOT COME ON UNTIL MY CAR STOPPED, THEN IT SAID WARNING LOW OIL PRESSURE. I HAD JUST HAD AN OIL CHANGE AT PORT CITY NISSAN, PORTS…
Read full complaint
I WAS DRIVING MY 2015 ALTIMA ON A HIGHWAY AND THE CAR SUDDENLY STOPPED AS IN A STALL WITH CARS BEHIND ME SWERVING OFF THE HIGHWAY TO AVOID HITTING ME. THE CAR HAD ON OIL AND THE OIL WARNING LIGHT DID NOT COME ON UNTIL MY CAR STOPPED, THEN IT SAID WARNING LOW OIL PRESSURE. I HAD JUST HAD AN OIL CHANGE AT PORT CITY NISSAN, PORTSMOUTH, NH, AND THE SERVICE PERSON APPARENTLY DID NOT REATTACH THE OIL FILTER CORRECTLY, CROSS-THREADING THE FILTER RESULTING IN THE OIL LEAKING OUT WITHOUT ME KNOWING. AGAIN, MY CONCERN IS THERE WAS NO WARNING BEFORE MY CAR STALLED AND STOPPED ON A HIGHWAY. NO OIL PRESSURE LIGHT OR LOW OIL ALERT, NOTHING UNTIL I WAS ALMOST IN A SERIOUS ACCIDENT.
PASSENGER AIR BAG TURNED OFF A FEW TIMES SINCE NEW. TOOK IN TO DEALER FOR RECALL TO REPROGRAM. WAS TOLD LIGHT WOULD BE ON UNTIL AN ADULT SAT IN THE SEAT. SEVERAL ADULTS HAVE SAT IN SEAT WITH ADEQUATE WEIGHT TO SENSE PRESENCE. AIR BAG IS STILL OFF AND HAS BEEN OFF SINCE REPROGRAMMED. DEALER SHOULD HAVE HAD PERSON SIT IN SEAT TO V…
Read full complaint
PASSENGER AIR BAG TURNED OFF A FEW TIMES SINCE NEW. TOOK IN TO DEALER FOR RECALL TO REPROGRAM. WAS TOLD LIGHT WOULD BE ON UNTIL AN ADULT SAT IN THE SEAT. SEVERAL ADULTS HAVE SAT IN SEAT WITH ADEQUATE WEIGHT TO SENSE PRESENCE. AIR BAG IS STILL OFF AND HAS BEEN OFF SINCE REPROGRAMMED. DEALER SHOULD HAVE HAD PERSON SIT IN SEAT TO VERIFY OPERATION PRIOR TO RELEASING AN UNSAFE VEHICLE TO CUSTOMER. HAVE NOT RETURNED TO THE DEALER.
GEAR SHIFT KEEPS SLIDING BETWEEN REVERSE AND NEUTRAL WITHOUT BEING TOUCHED.
HAVING FIXED A RECALL RELATED TO AIRBAG SENSORS, THE PASSENGER SIDE AIRBAG LIGHT KEEPS GOING OFF (INDICATING THE AIRBAG IS OFF) EVEN WHEN OCCUPIED BY A 130 POUND PASSENGER SITTING PROPERLY IN THE VEHICLE SEAT (BACK STRAIGHT AGAINST SET BACK, KNEES BENT AT EDGE OF SEAT, FEET FLAT ON THE FLOOR) WITH SEATBELT ON PROPERLY (LAPBELT A…
Read full complaint
HAVING FIXED A RECALL RELATED TO AIRBAG SENSORS, THE PASSENGER SIDE AIRBAG LIGHT KEEPS GOING OFF (INDICATING THE AIRBAG IS OFF) EVEN WHEN OCCUPIED BY A 130 POUND PASSENGER SITTING PROPERLY IN THE VEHICLE SEAT (BACK STRAIGHT AGAINST SET BACK, KNEES BENT AT EDGE OF SEAT, FEET FLAT ON THE FLOOR) WITH SEATBELT ON PROPERLY (LAPBELT ACROSS HIPS/LAP AND SHOULDER BELT ACROSS THE SHOULDER) THIS HAPPENS REPEATEDLY, THOUGH TO HAD TO SELECT 1 DATE TO FILE THIS REPORT.
CAR FAILS TO ACCELERATE AFTER A TOTAL STOP AND SITTING AT A TRAFFIC LIGHT. ABSOLUTELY NO POWER. THE GAS PEDAL CAN BE PRESSED ALL THE WAY TO THE FLOOR BEFORE VEHICLE BEGINS MOVING. THE GAS PEDAL WAS PRESSED GRADUALLY. AFTER A FEW SECONDS OF KEEPING THE PEDAL ON THE FLOOR, THE RPM WILL SPIKE AND THE CAR WILL SLOWLY BEGIN MOVING…
Read full complaint
CAR FAILS TO ACCELERATE AFTER A TOTAL STOP AND SITTING AT A TRAFFIC LIGHT. ABSOLUTELY NO POWER. THE GAS PEDAL CAN BE PRESSED ALL THE WAY TO THE FLOOR BEFORE VEHICLE BEGINS MOVING. THE GAS PEDAL WAS PRESSED GRADUALLY. AFTER A FEW SECONDS OF KEEPING THE PEDAL ON THE FLOOR, THE RPM WILL SPIKE AND THE CAR WILL SLOWLY BEGIN MOVING FORWARD. AFTER BACKING OFF THE PEDAL COMPLETELY, THE CAR CAN BE DRIVEN NORMALLY ONCE THE ENGINE SLOWS DOWN AND THE TRANSMISSION SHIFTS BACK. IT WAS APPROXIMATELY 80-85 DEGREES OUTSIDE, CLEAR, CAR WAS AT A SLIGHT INCLINE GOING UP A HILL. PLEASE SEE SIMILAR COMPLAINTS AT HTTP://WWW.CARCOMPLAINTS.COM/NISSAN/ALTIMA/2015/TRANSMISSION/HESITATES_SPUTTERS.SHTML
TL* THE CONTACT OWNS A 2015 NISSAN ALTIMA. THE CONTACT STATED THAT WHILE OPERATING THE VEHICLE, THE RPM'S WOULD SUDDENLY INCREASE TO APPROXIMATELY 4000 TO 6000 BUT VEHICLE WOULD NOT ACCELERATE PROPERLY. THE VEHICLE WAS TAKEN TO THE DEALER WHO WAS ABLE TO EXPERIENCE THE FAILURE BUT WAS UNABLE TO DETERMINE THE CAUSE OF THE FAILURE…
Read full complaint
TL* THE CONTACT OWNS A 2015 NISSAN ALTIMA. THE CONTACT STATED THAT WHILE OPERATING THE VEHICLE, THE RPM'S WOULD SUDDENLY INCREASE TO APPROXIMATELY 4000 TO 6000 BUT VEHICLE WOULD NOT ACCELERATE PROPERLY. THE VEHICLE WAS TAKEN TO THE DEALER WHO WAS ABLE TO EXPERIENCE THE FAILURE BUT WAS UNABLE TO DETERMINE THE CAUSE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 22,000.
DIRECTION OF CAR "WONDERS" SLIGHTLY FROM SIDE-TO-SIDE WHEN DRIVING AT HIGHWAY SPEEDS. NEED CONTINUOUS SMALL STEERING WHEEL CORRECTION IN ORDER TO KEEP CAR IN STRAIGHT LINE. VERY ANNOYING AND STRESSFUL TO OPERATE CAR.
Official recalls
1020V315000 · Latches/locks/linkages:hood:latch
May 28, 2020
Nissan North America, Inc. (Nissan) is recalling certain model year 2013-2018 Nissan Altima vehicles. If the primary hood latch is inadvertently released, there is an increased likelihood that the secondary hood latch may corrode over time.
Consequence & remedy
Consequence: Corrosion to the secondary latch may cause it to bind and remain in the unlatched position when the hood is closed. If the primary latch is inadvertently released again and the secondary latch is not engaged, the hood could unexpectedly open while driving, increasing the risk of a vehicle crash.
Remedy: Nissan will notify owners, and dealers will install a stronger release spring in the hood release lever, a warning label near the secondary hood latch, and an Owners Manual addendum card with instructions on how to lubricate and maintain the secondary hood latch mechanism, free of charge. Owner notification letters were mailed June 30, 2021. Owners may contact Nissan customer service at 1-800-867-7669. Note: Recall 16V-029 remains open for any unremedied 2013-2015 Altimas and this recall applies to all vehicles covered by 16V-029 even if those repairs have already been performed.
18V915000 · Latches/locks/linkages:doors:latch; Structure:emergency:escape/egress/exit
Dec 19, 2018
Nissan North America, Inc. (Nissan) is recalling certain 2015-2017 Altima vehicles, previously remedied under recall number 17V-040. The door latch-lock cable may not have been routed properly in the rear door when the remedy was applied. As a result, the cable may interfere with the window regulator causing the rear passenger door to unlatch and inadvertently open without warning when the window is lowered.
Consequence & remedy
Consequence: If the rear passenger door opens while the vehicle is moving, the rear passengers have an increased risk of injury.
Remedy: Nissan will notify owners, and dealers will secure the latch-lock cables in the correct position using the new remedy procedure, free of charge. The recall began February 5, 2019. Owners may contact Nissan customer service at 1-800-647-7669.
Additional source detail variants (2)
Structure:emergency:escape/egress/exit
Nissan North America, Inc. (Nissan) is recalling certain 2015-2017 Altima vehicles, previously remedied under recall number 17V-040. The door latch-lock cable may not have been routed properly in the rear door when the remedy was applied. As a result, the cable may interfere with the window regulator causing the rear passenger door to unlatch and inadvertently open without warning when the window is lowered.
Consequence: If the rear passenger door opens while the vehicle is moving, the rear passengers have an increased risk of injury.
Remedy: Nissan will notify owners, and dealers will secure the latch-lock cables in the correct position using the new remedy procedure, free of charge. The recall began February 5, 2019. Owners may contact Nissan customer service at 1-800-647-7669.
Latches/locks/linkages:doors:latch
Nissan North America, Inc. (Nissan) is recalling certain 2015-2017 Altima vehicles, previously remedied under recall number 17V-040. The door latch-lock cable may not have been routed properly in the rear door when the remedy was applied. As a result, the cable may interfere with the window regulator causing the rear passenger door to unlatch and inadvertently open without warning when the window is lowered.
Consequence: If the rear passenger door opens while the vehicle is moving, the rear passengers have an increased risk of injury.
Remedy: Nissan will notify owners, and dealers will secure the latch-lock cables in the correct position using the new remedy procedure, free of charge. The recall began February 5, 2019. Owners may contact Nissan customer service at 1-800-647-7669.
17V040000 · Latches/locks/linkages:doors:latch
Jan 18, 2017
Nissan North America, Inc. (Nissan) is recalling certain 2015-2017 Altima vehicles. The rear door latch/lock cable on the vehicles may have been improperly routed. As a result, lowering a rear window may inadvertently cause that door to unlatch and open.
Consequence & remedy
Consequence: If the rear passenger doors inadvertently open while the vehicle is in motion, it may increase the risk of injury to the rear passengers.
Remedy: Nissan will notify owners, and dealers will correct the rear door latch/lock cable routing, free of charge. The recall began on February 16, 2017. Owners may contact Nissan customer service at 1-800-647-7261.
16V911000 · Air Bags:sensor:occupant Classification
Dec 19, 2016
Nissan North America, Inc. (Nissan) is recalling certain model year 2013-2015 Altima vehicles manufactured January 3, 2013, to July 29, 2013, 2015-2016 Rogue vehicles manufactured October 14, 2014, to August 12, 2016, and 2016 Maxima vehicles manufactured June 4, 2015, to August 19, 2015. An incorrect Occupant Classification System (OCS) Electronic Control Unit (ECU) may have been installed in the front passenger seat. The incorrect ECU and seat combination may misclassify the front passenger seat occupant.
Consequence & remedy
Consequence: If the front passenger seat occupant is misclassified, the air bag may deploy incorrectly in the event of a crash, increasing the risk of injury.
Remedy: Nissan will notify owners, and dealers will replace the ECU and update the OCS software free of charge. The recall began February 13, 2017. Owners may contact Nissan customer service at 1-800-647-7261.
16V244000 · Air Bags:sensor:occupant Classification
Apr 26, 2016
Nissan North America, Inc. (Nissan) is recalling certain model year 2016-2017 Nissan Maxima, 2013-2016 Nissan Altima, NV200, LEAF, Sentra, and Pathfinder, 2014-2016 Nissan NV200 Taxi, Infiniti QX60, QX60 Hybrid, and Q50 Hybrid, 2014-2017 Nissan Rogue and Infiniti Q50, 2015-2016 Nissan Murano, Murano Hybrid, and Chevrolet City Express, 2014-2015 Nissan Pathfinder Hybrid, and 2013 Infiniti JX35 vehicles. In these vehicles, the front seat passenger Occupant Classification System (OCS) may incorrectly classify an adult passenger as a child or classify the seat as empty despite it being occupied. As a result, the passenger frontal air bag may be turned off and not deploy in the event of a crash.
Consequence & remedy
Consequence: If the passenger frontal air bag does not deploy as intended in the event of a crash, the passenger is at an increased risk of injury.
Remedy: Nissan will notify their owners. Chevrolet City Express owners will be notified by General Motors. Dealers will reprogram the Air Bag Control Unit (ACU) and OCS Electronic Control Unit (ECU) in Altima, Maxima, Murano, Rogue, and Sentra vehicles, and replace the OCS ECU in LEAF, NV200, NV200 Taxi, Pathfinder, Infiniti Q50, JX35, and QX60 and Chevrolet City Express vehicles, free of charge. Interim notices were sent to owners on May 31, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Nissan customer service at 1-800-867-7669, Infiniti customer service at 1-888-833-3216 or Chevrolet customer service at 1-800-222-1020.
16V029000 · Latches/locks/linkages:hood:latch
Jan 22, 2016
Nissan North America, Inc. (Nissan) is recalling certain model year 2013-2015 Nissan Altima vehicles manufactured March 6, 2012, to December 31, 2014. In the affected vehicles, the secondary hood latch may bind and remain in the unlatched position when the hood is closed.
Consequence & remedy
Consequence: If the primary latch is inadvertently released and the secondary latch is not engaged, the hood could unexpectedly open while driving, increasing the risk of a vehicle crash.
Remedy: These vehicles were previously included in recalls 14V-565 and 15V-116, however the previous remedy plan may not have been performed consistently to remove the safety risk. To correct this issue, Nissan will re-notify all affected owners and dealers will replace the hood latch with a new one, free of charge. The recall began on February 17, 2016. Owners may contact Nissan customer service at 1-800-647-7261. Note: This recall supersedes recalls 14V-565 and 15V-116.
15V733000 · Service Brakes, Hydraulic:foundation Components:disc:caliper
Nov 5, 2015
Nissan North America, Inc. (Nissan) is recalling certain model year 2015 Altima and 2016 Maxima vehicles manufactured October 6, 2015, to October 7, 2015. The affected vehicles have front brake calipers whose mounting bolts may not be properly tightened.
Consequence & remedy
Consequence: If the bolts were not properly tightened, the caliper may detach and reduce braking ability, increasing the risk of a crash.
Remedy: Nissan will notify owners, and dealers will check the brake caliper mounting bolts, tightening them as necessary, free of charge. The recall began on December 14, 2015. Owners may contact Nissan customer service at 1-800-647-7261.
15V681000 · Air Bags:frontal; Air Bags:sensor:occupant Classification
Oct 20, 2015
Nissan North America, Inc. (Nissan) is recalling certain model year 2013-2015 Altima and Pathfinder vehicles, 2013-2014 Nissan Sentra vehicles, 2013 Infiniti JX35 vehicles, 2014-2015 Infiniti QX60 vehicles and 2014 Infiniti QX60 Hybrid vehicles. The affected vehicles received an incorrect occupant classification system (OCS) control unit during a repair. These OCS control units may incorrectly classify the front passenger seat as empty, when it is occupied by an adult.
Consequence & remedy
Consequence: If the OCS does not detect an adult occupant in the passenger seat, the passenger air bag would be deactivated. Failure of the passenger airbag to deploy during a crash (where deployment is warranted) could increase the risk of injury to the passenger.
Remedy: Nissan will notify owners, and dealers will update the OCS software, free of charge. The recall began on November 30, 2015. Owners may contact Nissan at 1-800-647-7261.
Additional source detail variants (2)
Air Bags:sensor:occupant Classification
Nissan North America, Inc. (Nissan) is recalling certain model year 2013-2015 Altima and Pathfinder vehicles, 2013-2014 Nissan Sentra vehicles, 2013 Infiniti JX35 vehicles, 2014-2015 Infiniti QX60 vehicles and 2014 Infiniti QX60 Hybrid vehicles. The affected vehicles received an incorrect occupant classification system (OCS) control unit during a repair. These OCS control units may incorrectly classify the front passenger seat as empty, when it is occupied by an adult.
Consequence: If the OCS does not detect an adult occupant in the passenger seat, the passenger air bag would be deactivated. Failure of the passenger airbag to deploy during a crash (where deployment is warranted) could increase the risk of injury to the passenger.
Remedy: Nissan will notify owners, and dealers will update the OCS software, free of charge. The recall began on November 30, 2015. Owners may contact Nissan at 1-800-647-7261.
Air Bags:frontal
Nissan North America, Inc. (Nissan) is recalling certain model year 2013-2015 Altima and Pathfinder vehicles, 2013-2014 Nissan Sentra vehicles, 2013 Infiniti JX35 vehicles, 2014-2015 Infiniti QX60 vehicles and 2014 Infiniti QX60 Hybrid vehicles. The affected vehicles received an incorrect occupant classification system (OCS) control unit during a repair. These OCS control units may incorrectly classify the front passenger seat as empty, when it is occupied by an adult.
Consequence: If the OCS does not detect an adult occupant in the passenger seat, the passenger air bag would be deactivated. Failure of the passenger airbag to deploy during a crash (where deployment is warranted) could increase the risk of injury to the passenger.
Remedy: Nissan will notify owners, and dealers will update the OCS software, free of charge. The recall began on November 30, 2015. Owners may contact Nissan at 1-800-647-7261.
15V486000 · Fuel System, Gasoline
Aug 4, 2015
Nissan North America, Inc. (Nissan) notified the agency on July 31, 2015, that they are recalling certain model year 2016 Nissan Maxima vehicles manufactured February 10, 2015, to August 18, 2015. On October 14, 2015, Nissan expanded the recall to cover an additional 41,388 vehicles, including certain model year 2013-2015 Altima 3.5 vehicles equipped with a V6 engine manufactured March 30, 2012, to August 18, 2015 as well as the vehicles covered by the July 31, 2015 notification. In the affected vehicles, due to an improperly installed o-ring that may not have been seated correctly at the time of assembly, fuel may leak during a crash from the area where the fuel sending unit attaches to the fuel tank.
Consequence & remedy
Consequence: If fuel leaks from between the fuel sending unit and the tank, it may increase the risk of a fire in the event of a crash.
Remedy: Nissan will notify owners, and dealers will install a retainer ring between the fuel tank and the fuel sending unit. The recall began on September 28, 2015. Owners may contact Nissan customer service at 1-800-647-7261.
15V116000 · Latches/locks/linkages:hood:latch
Feb 27, 2015
Nissan North America, Inc. (Nissan) is recalling certain model year 2013-2015 Nissan Altima vehicles manufactured March 1, 2013, to December 31, 2014. In the affected vehicles, the secondary hood latch may bind and remain in the unlatched position when the hood is closed.
Consequence & remedy
Consequence: If the primary latch is inadvertently released and the secondary latch is not engaged, the hood could unexpectedly open while driving, increasing the risk of a vehicle crash.
Remedy: Nissan will notify owners, and dealers will be instructed to modify the bend angle of the hood actuation lever to eliminate potential interference with the hood inner panel. In addition, dealers will clean and lubricate the latch joint as needed. If significant corrosion is observed, the latch assembly will be replaced. This repairs will be performed free of charge. The recall began March 31, 2015. Owners may contact Nissan customer service at 1-800-647-7261. Note: This recall is an expansion of recall 14V-565.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA19002 · Rear Suspension Control Arm Failure
Opened Jul 29, 2019 · Closed Jun 16, 2025
Status: closed (inferred from source dates) · Suspension:rear
On July 29, 2019, the Office of Defects Investigation (ODI) opened EA19002 to investigate instances of alleged rear lower control arm failures in 2013-2018 Nissan Altima and 2016-2018 Nissan Maxima vehicles. At the time the investigation was opened ODI had 91 consumer complaints alleging rear lower control arm failures in the subject vehicles.ODI was concerned about these complaints because many of them alleged an increased steering effort or loss of vehicle control.At the time these complaints were received, ODI was also aware of a proactive service campaign addressing 2013 Nissan Altima in salt-belt states for a similar concern. Since opening the investigation, ODI has confirmed, based on consumer complaints, warranty data, and testing conducted by Nissan and ODI, that owners of the subject vehicles are experiencing a corroded bushing at one of three mounting points of the control arm to the rear subframe.ODI has also confirmed that drivers become aware of the problem because of sound and abnormal vibrations. In addition, the failure mileage is typically over 113,000 miles at the time of failure.In conjunction with Nissan and VRTC, ODI participated in testing to assess the potential safety consequence of a bushing failure.It was found the Vehicle Dynamic Control system allows the driver to maintain vehicle control in the event of a bushing failure.With between 7 to 13 years of field exposure, ODI is aware of only one low speed crash allegation describing minor contact with another vehicle’s trailer hitch. Nissan acknowledges that a crack can develop in affected control arms due to stress loading from normal use and that salts commonly used for roadway snow and ice treatment may result in corrosion that exacerbates the progression of the crack.Nissan implemented a design change in January of 2018 to improve the durability of the lower control arm.Affected vehicles have either been repaired with the countermeasure part under a customer satisfaction campaign or been provided a warranty extension from 3 years/36,000 miles to 10 year/unlimited mileage. Through testing and analysis of the information obtained to date, ODI has not identified a defect representing an unreasonable risk to motor vehicle safety involving corrosion of the subject rear lower control arm at this time.With a declining trend of reports and Nissan’s actions to implement a countermeasure and extended warranty coverage, further investigation of the issue does not appear to be warranted at this time.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov. A detailed discussion of the investigation and related complaint numbers can be viewed in the attached closing report.
PE18013 · Rear Suspension Control Arm Failure
Opened Dec 1, 2018 · Closed Aug 21, 2019
Status: closed (inferred from source dates) · Suspension:rear
PE18-013 was opened on December 1, 2018, with 4 complaints to ODI alleging incidents of the lower control arm fracturing at a connection point to the vehicle chassis due to corrosion. ODI has received an additional 87 complaints since the PE was opened. During PE18-013, Nissan indicated model years 2013-2018 shared a common rear lower control arm design. Nissan provided complaint and warranty data regarding 48 incidents of the subject failure. The majority of the complaints are from vehicles registered in salt belt states. There have been no crashes, injuries, or fatalities confirmed as of this date. Nissan advised that it has conducted testing to assess safety risk. Nissan states that due to low incident rate, high detectability, and low risk of adverse vehicle dynamics, it does not believe the subject lower control arm failure poses an unreasonable risk to motor vehicle safety.This preliminary evaluation has been upgraded to Engineering Analysis (EA) 19-002. During the EA, ODI will continue to collect and analyze complaint and field data in its efforts to fully assess the scope and frequency of the alleged defect. More importantly, ODI will also seek additional information and data regarding the potential safety consequences of rear lower control arm failure, both from evidence collected from field failures and through more rigorous and comprehensive vehicle testing to be conducted by either Nissan and/or NHTSA.The ODI reports (VOQs) cited above can be viewed at NHTSA.gov under the following reference numbers: 11234334, 11234232, 11234189, 11233771, 11233234, 11232381, 11231589, 11230323, 11230184, 11229023, 11229003, 11228730, 11228651, 11228631, 11228625, 11223086, 11222602, 11222427, 11222303, 11221802, 11219943, 11217980, 11217542, 11217505, 11217290, 11210699, 11209647, 11208580, 11208274, 11207545, 11206310, 11205711, 11205461, 11203864, 11203005, 11195416, 11193545, 11193020, 11192269, 11192066, 11191270, 11191207, 11191185, 11191042, 11190360, 11190323, 11187334, 11187157, 11186747, 11186195, 11185664, 11185632, 11185589, 11183799, 11183295, 11183198, 11182705,11182528, 11182265, 11182137, 11182088, 11181373, 11181223, 11181155, 11181009, 11180126, 11176565, 11176261, 11176135, 11175821, 11172604, 11172200, 11172065, 11170019, 11169930, 11165194, 11163833, 11163489, 11162559, 11162195, 11161956, 11161497, 11161117, 11157323, 11157234, 11156772, 11141169, 11139516, 11129476, 11122829, 11114374.