EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA19002 · Rear Suspension Control Arm Failure
Opened Jul 29, 2019 · Closed Jun 16, 2025
Status: closed (inferred from source dates) · Suspension:rear
On July 29, 2019, the Office of Defects Investigation (ODI) opened EA19002 to investigate instances of alleged rear lower control arm failures in 2013-2018 Nissan Altima and 2016-2018 Nissan Maxima vehicles. At the time the investigation was opened ODI had 91 consumer complaints alleging rear lower control arm failures in the subject vehicles.ODI was concerned about these complaints because many of them alleged an increased steering effort or loss of vehicle control.At the time these complaints were received, ODI was also aware of a proactive service campaign addressing 2013 Nissan Altima in salt-belt states for a similar concern. Since opening the investigation, ODI has confirmed, based on consumer complaints, warranty data, and testing conducted by Nissan and ODI, that owners of the subject vehicles are experiencing a corroded bushing at one of three mounting points of the control arm to the rear subframe.ODI has also confirmed that drivers become aware of the problem because of sound and abnormal vibrations. In addition, the failure mileage is typically over 113,000 miles at the time of failure.In conjunction with Nissan and VRTC, ODI participated in testing to assess the potential safety consequence of a bushing failure.It was found the Vehicle Dynamic Control system allows the driver to maintain vehicle control in the event of a bushing failure.With between 7 to 13 years of field exposure, ODI is aware of only one low speed crash allegation describing minor contact with another vehicle’s trailer hitch. Nissan acknowledges that a crack can develop in affected control arms due to stress loading from normal use and that salts commonly used for roadway snow and ice treatment may result in corrosion that exacerbates the progression of the crack.Nissan implemented a design change in January of 2018 to improve the durability of the lower control arm.Affected vehicles have either been repaired with the countermeasure part under a customer satisfaction campaign or been provided a warranty extension from 3 years/36,000 miles to 10 year/unlimited mileage. Through testing and analysis of the information obtained to date, ODI has not identified a defect representing an unreasonable risk to motor vehicle safety involving corrosion of the subject rear lower control arm at this time.With a declining trend of reports and Nissan’s actions to implement a countermeasure and extended warranty coverage, further investigation of the issue does not appear to be warranted at this time.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov. A detailed discussion of the investigation and related complaint numbers can be viewed in the attached closing report.
PE18013 · Rear Suspension Control Arm Failure
Opened Dec 1, 2018 · Closed Aug 21, 2019
Status: closed (inferred from source dates) · Suspension:rear
PE18-013 was opened on December 1, 2018, with 4 complaints to ODI alleging incidents of the lower control arm fracturing at a connection point to the vehicle chassis due to corrosion. ODI has received an additional 87 complaints since the PE was opened. During PE18-013, Nissan indicated model years 2013-2018 shared a common rear lower control arm design. Nissan provided complaint and warranty data regarding 48 incidents of the subject failure. The majority of the complaints are from vehicles registered in salt belt states. There have been no crashes, injuries, or fatalities confirmed as of this date. Nissan advised that it has conducted testing to assess safety risk. Nissan states that due to low incident rate, high detectability, and low risk of adverse vehicle dynamics, it does not believe the subject lower control arm failure poses an unreasonable risk to motor vehicle safety.This preliminary evaluation has been upgraded to Engineering Analysis (EA) 19-002. During the EA, ODI will continue to collect and analyze complaint and field data in its efforts to fully assess the scope and frequency of the alleged defect. More importantly, ODI will also seek additional information and data regarding the potential safety consequences of rear lower control arm failure, both from evidence collected from field failures and through more rigorous and comprehensive vehicle testing to be conducted by either Nissan and/or NHTSA.The ODI reports (VOQs) cited above can be viewed at NHTSA.gov under the following reference numbers: 11234334, 11234232, 11234189, 11233771, 11233234, 11232381, 11231589, 11230323, 11230184, 11229023, 11229003, 11228730, 11228651, 11228631, 11228625, 11223086, 11222602, 11222427, 11222303, 11221802, 11219943, 11217980, 11217542, 11217505, 11217290, 11210699, 11209647, 11208580, 11208274, 11207545, 11206310, 11205711, 11205461, 11203864, 11203005, 11195416, 11193545, 11193020, 11192269, 11192066, 11191270, 11191207, 11191185, 11191042, 11190360, 11190323, 11187334, 11187157, 11186747, 11186195, 11185664, 11185632, 11185589, 11183799, 11183295, 11183198, 11182705,11182528, 11182265, 11182137, 11182088, 11181373, 11181223, 11181155, 11181009, 11180126, 11176565, 11176261, 11176135, 11175821, 11172604, 11172200, 11172065, 11170019, 11169930, 11165194, 11163833, 11163489, 11162559, 11162195, 11161956, 11161497, 11161117, 11157323, 11157234, 11156772, 11141169, 11139516, 11129476, 11122829, 11114374.
Illustration