NHTSA owner reports · September 18, 2026 snapshot.
Exterior Lighting complaints
135 reportsClear category filter49,500 miles · Jun 17, 2014
Exterior Lighting
TL* THE CONTACT OWNS A 2010 MERCURY MILAN. THE CONTACT STATED THAT THE REAR BRAKE LIGHT ILLUMINATED. THE CONTACT MENTIONED THAT THERE WERE NO WARNING LIGHTS ILLUMINATED ON THE INSTRUMENT PANEL. THE FAILURE RECURRED. THE MANUFACTURER WAS CONTACTED. THE VEHICLE WAS TAKEN TO THE DEALER. THE TECHNICIAN DIAGNOSED THAT THE TAIL L…
Read full complaint
TL* THE CONTACT OWNS A 2010 MERCURY MILAN. THE CONTACT STATED THAT THE REAR BRAKE LIGHT ILLUMINATED. THE CONTACT MENTIONED THAT THERE WERE NO WARNING LIGHTS ILLUMINATED ON THE INSTRUMENT PANEL. THE FAILURE RECURRED. THE MANUFACTURER WAS CONTACTED. THE VEHICLE WAS TAKEN TO THE DEALER. THE TECHNICIAN DIAGNOSED THAT THE TAIL LIGHT ASSEMBLY NEEDED TO BE REPLACED. THE FAILURE MILEAGE WAS 49,500 AND THE CURRENT MILEAGE WAS 50,000. UPDATED 8/12/14*CN THE CONSUMER STATED THE RIGHT STOP LIGHT WAS ALWAYS ON WITH THE TAIL LIGHT. THEN THE RIGHT SIDE LIGHT WENT OUT. UPDATED 09/23/14
NHTSA ODI #10598763
16,000 miles · Jun 11, 2014
Exterior Lighting
BACK TAIL LIGHT ASSEMBLY (LED PANEL) OF THE 2010 MILAN IS FAULTY. SOME LIGHTS WOULD NOT LIGHT UP AT ALL AND AT ONE POINT SOMEONE REPORTED NONE WERE LIGHTING UP. THE CAR WAS JUST OVER THE WARRANTY WITH ONLY 16,000 MILES. CHECKING ONLINE IT APPEARS THIS IS A SERIOUS PROBLEM WITH THIS MODEL AND YEAR CAR AND MANY HAVE EXPERIENCED TH…
Read full complaint
BACK TAIL LIGHT ASSEMBLY (LED PANEL) OF THE 2010 MILAN IS FAULTY. SOME LIGHTS WOULD NOT LIGHT UP AT ALL AND AT ONE POINT SOMEONE REPORTED NONE WERE LIGHTING UP. THE CAR WAS JUST OVER THE WARRANTY WITH ONLY 16,000 MILES. CHECKING ONLINE IT APPEARS THIS IS A SERIOUS PROBLEM WITH THIS MODEL AND YEAR CAR AND MANY HAVE EXPERIENCED THE PROBLEM WITH LOW MILEAGE EVEN WITH REPLACEMENT PANELS (AT UPWARDS OF $400 FOR THE PART). SINCE IT IS IMPOSSIBLE FOR A DRIVER TO KNOW IF/WHEN THE LIGHTS ARE OR ARE NOT WORKING - IT IS A SERIOUS DANGER FOR ANYONE DRIVING BEHIND A MILAN. NHTSA SHOULD FORCE A RECALL OF THE PARTS BEFORE SOMEONE IS REAR ENDED AND KILLED. FORD AND THEIR DEALERSHIPS DO NOT CARE. *TR
NHTSA ODI #10597776
32,000 miles · Jun 2, 2014
Electrical SystemExterior Lighting
WHEN THE HEADLIGHTS SWITCH IS IN THE ON OR PARKING LIGHTS ONLY, THE RIGHT AND LEFT BRAKE LIGHTS COME ON AT FULL BRIGHTNESS. WHEN BRAKES PEDAL IS DEPRESSED, THERE IS NO CHANGE IN BRIGHTNESS OF RIGHT AND LEFT BRAKE LIGHTS AND THE CENTER REAR BRAKE LIGHT ILLUMINATES. WHEN THIS WAS TAKEN IN FOR A REQUIRED NY STATE INSPECTION, THE …
Read full complaint
WHEN THE HEADLIGHTS SWITCH IS IN THE ON OR PARKING LIGHTS ONLY, THE RIGHT AND LEFT BRAKE LIGHTS COME ON AT FULL BRIGHTNESS. WHEN BRAKES PEDAL IS DEPRESSED, THERE IS NO CHANGE IN BRIGHTNESS OF RIGHT AND LEFT BRAKE LIGHTS AND THE CENTER REAR BRAKE LIGHT ILLUMINATES. WHEN THIS WAS TAKEN IN FOR A REQUIRED NY STATE INSPECTION, THE VEHICLE FAILED DUE TO THIS ISSUE. THE MECHANIC WORKING ON THE VEHICLE HAS STATED THAT THIS IS A VERY COMMON ISSUE WITH THIS YEAR, MAKE AND MODEL. DEALER HAS BEEN CONTACTED AND STATED THE COST WOULD BE IN EXCESS OF $1,000 TO REPAIR THIS ISSUE. THIS IS A SAFETY ISSUE THAT IS MOST LIKELY TO LEAD TO REAR END COLLISIONS AND IS COMMON IN SEVERAL DIFFERENT VEHICLES OF THIS YEAR, MAKE AND MODEL. MANUFACTURER SHOULD BE RECALLING VEHICLES OF THIS YEAR, MAKE AND MODEL TO REPAIR THIS ISSUE. *TR
NHTSA ODI #10595454
29,500 miles · May 27, 2014
Exterior Lighting
AFTER BEING TOLD ON SEVERAL OCCASIONS THAT OUR LEFT TAIL LIGHT AND BRAKE LIGHT WAS NOT WORKING, ON 5/19/14 OUR 2010 MILAN WAS TAKEN IN FOR ROUTINE MAINTENTANCE BY THE DEALER. AT THAT TIME,THEY WERE ASKED TO ADDRESS THE TAIL LIGHT AND BRAKE LIGHT PROBLEM. THE VEHICLE HAD 35,070 MILES ON THE ODOMETER AND ALTHOUGH THE NEW CAR WARRA…
Read full complaint
AFTER BEING TOLD ON SEVERAL OCCASIONS THAT OUR LEFT TAIL LIGHT AND BRAKE LIGHT WAS NOT WORKING, ON 5/19/14 OUR 2010 MILAN WAS TAKEN IN FOR ROUTINE MAINTENTANCE BY THE DEALER. AT THAT TIME,THEY WERE ASKED TO ADDRESS THE TAIL LIGHT AND BRAKE LIGHT PROBLEM. THE VEHICLE HAD 35,070 MILES ON THE ODOMETER AND ALTHOUGH THE NEW CAR WARRANTY HAD EXPIRED, WE HAD PURCHASED BOTH PREMIUM CARE AND ESP AT THE TIME OF PURCHASE TO THE TUNE OF OVER $2000. I WAS SHOCKED AND VERY ANGRY WHEN I WAS INFORMED THAT THE LEFT LED TAIL LIGHT WOULD NEED TO BE REPLACED AT A COST OF OVER $400 AND IT WOULD NOT BE COVERED UNDER EITHER PROGRAM. SUBSEQUENTLY, IN CHECKING THE SMALL PRINT, I DISCOVERED THAT LED LIGHTS WERE INDEED EXCLUDED UNDER EITHER PROGRAM. CHECKING FURTHER, I FOUND THAT THERE ARE NUMEROUS COMPLAINTS OF WHAT CERTAINLY APPEARS TO BE A MANUFACTURER DEFECT AND A SAFETY ISSUE REGARDING THE LED TAIL LIGHTS THE FORD DEALER SERVICE ADVISOR DID NOT SEEM BE SURPRISED AT MY OUTRAGE SINCE THIS SEEMINGLY IS A PROBLEM THAT HE EVIDENTLY HAS DEALT WITH BEFORE. NOW IT APPEARS MY RIGHT BRAKE LIGHT IS STAYING LIT AND DOES NOT FUNCTION WHEN THE BRAKE IS APPLIED AND I COULD BE FACED WITH A $1000 REPAIR BILL. EVIDENTLY FORD IS GOING TO HAVE TO BE FORCED TO ADDRESS THIS PROBLEM. ONE COULD BE DRIVING ALONG WITHOUT KNOWING THEIR STOP/BRAKE LIGHTS WERE NOT WORKING SINCE THERE IS NO VISUAL ALERT ON THE MESSAGE CENTER AND WONDER WHY THEY WERE SUDDENLY REAR-ENDED BY A FOLLOWING VEHICLE AT A TRAFFIC LIGHT. BESIDES THE EXPENSE TO THE OWNER, THERE IS A REAL SAFETY ISSUE THAT NEEDS TO BE ADDRESSED! THE LACK OF BRAKE LIGHTS COULD RESULT IN SERIOUS INJURY AND OR DEATH AND CONSIDERABLE DAMAGE. THE PROBLEM IS AN OBVIOUS DEFECT IN MATERIALS IF NOT WORKMANSHIP AND THE COMPANY IS CLEARLY LIABLE. THE LIFE EXPECTANCY OF LED LIGHT STRIPS IS CERTAINLY MUCH LONGER THAN THE ORDINARY LIGHT BULB, SO WHAT IS GOING ON? *TR
NHTSA ODI #10594232
30,000 miles · May 27, 2014
Exterior Lighting
THE PASSENGER SIDE LED TAIL LIGHT IS NO LONGER WORKING. THE CAR IS NOT EVEN 5 YEARS OLD YET. LEDS SHOULD NOT FAIL THIS QUICKLY SINCE THIS IS A CRITICAL SAFETY PART. MY UNDERSTANDING IS THAT IT IS NOT COVERED UNDER MY FORD PREMIUM LEVEL EXTENDED WARRANTY. IT IS A COSTLY PART. *TR
NHTSA ODI #10594226
40,000 miles · May 26, 2014
Exterior Lighting
BRAKE LIGHT FAILURE. CAR HAS LED BRAKE/TAIL LIGHTS. BRAKE LIGHT ON LEFT SIDE WOULD INTERMITTENTLY FLASH WHEN HEADLIGHTS ON. CHANGED COMPLETE TAILLIGHT. ($375) PROBLEM FIXED. 13 MONTHS LATER SAME BRAKE LIGHT FAILED, BRAKE LIGHT DOES NOT ILLUMINATE AT ALL. WIRING OK, NEEDS ANOTHER TAIL LIGHT ASSEMBLY. ANOTHER $375. *TR
NHTSA ODI #10594122
43,000 miles · May 20, 2014
Exterior Lighting
IN APRIL 2013 I NOTICED THAT MY LEFT BACK TAIL LIGHT WOULD GO OUT AND COME BACK ON INTERMITTENTLY. EVENTUALLY THE TAIL LIGHT STAYED ON, BUT IT WAS NOT A NORMAL TAIL LIGHT THE BRIGHTNESS INDICATED THAT IT WAS A BRAKE LIGHT. EVERY TIME I TURN ON MY LIGHTS THE BRAKE LIGHT ILLUMINATES AS A TAIL LIGHT. NOW MARCH 2014 MY BRAKE LIGHT I…
Read full complaint
IN APRIL 2013 I NOTICED THAT MY LEFT BACK TAIL LIGHT WOULD GO OUT AND COME BACK ON INTERMITTENTLY. EVENTUALLY THE TAIL LIGHT STAYED ON, BUT IT WAS NOT A NORMAL TAIL LIGHT THE BRIGHTNESS INDICATED THAT IT WAS A BRAKE LIGHT. EVERY TIME I TURN ON MY LIGHTS THE BRAKE LIGHT ILLUMINATES AS A TAIL LIGHT. NOW MARCH 2014 MY BRAKE LIGHT IN MY BACK WINDOW WENT OUT. I REPLACED THE BULB IN THIS LIGHT. TWO WEEKS AGO MAY 2014 MY TAIL LIGHT ON THE RIGHT SIDE WENT OUT AND WHEN I USED MY BRAKES THE RIGHT BRAKE WOULD BLINK LIKE A BLINKER. CURRENTLY TODAY. I HAVE A TAIL LIGHT ON THE LEFT THAT IS AS BRIGHT AS THE BRAKE, WHEN THE TAIL LIGHTS ARE ON I DON'T HAVE A BRAKE LIGHT. WHEN THE LIGHTS ARE OFF THE BRAKE LIGHT WORKS. ON THE RIGHT SIDE I DO NOT HAVE A TAIL LIGHT OR A BRAKE LIGHT. SO WHEN THE LIGHTS ARE ON, I HAVE ONE TAIL LIGHT OUT COMPLETELY. WHEN I HAVE MY TAIL LIGHTS ON THE ONLY BRAKE LIGHT I HAVE IS IN THE BACK WINDOW. I CALLED TODAY ABOUT REPLACEMENTS AND WAS QUOTED $376.20 A PIECE! THAT IS ONLY THE PART. I DID HAVE AN ELECTRICIAN FRIEND COME OUT AND TEST THE WIRING AND NOPE NOT THE WIRING, IT IS ALL IN THE LIGHT. I CAN NOT AFFORD TO GET THIS FIXED. FORD NEEDS TO STEP UP! THIS IS THE 6TH FORD WE HAVE HAD. THIS IS THE ONLY ISSUE I HAVE EVER HAD. IF FORD DOES NOT TAKE REASONABILITY I WILL BE TRADING IT IN FOR A TOYOTA! *TR
NHTSA ODI #10592776
46,000 miles · Apr 17, 2014
Exterior Lighting
LED TAIL LIGHTS WILL FLICKER OR NOT WORK AT ALL - IN DOING A LITTLE RESEARCH I FOUND OUT IT IS A PRETTY COMMON PROBLEM WITH THESE - FORD WILL OFFER NO HELP WITH THIS KNOWN SAFETY DEFECT. *TT
NHTSA ODI #10583397
52,000 miles · Apr 14, 2014
Exterior Lighting
I WAS ASKED TO PULL OVER BY A FRIEND WHO TOLD ME THE BRAKE LIGHTS WEREN'T ACTIVATING ON THE PASSENGER SIDE OF THE VEHICLE. CENTER AND LEFT SIDE WERE OPERATIONAL. WHEN I TURN OFF THE HEADLIGHTS, THE BRAKE LIGHTS ARE OPERATIONAL. AN OBVIOUS SYSTEM FAILURE WITHIN THE SEALED LIGHT. CANNOT REPLACE THIS LED LIGHT, THE ENTIRE TAIL L…
Read full complaint
I WAS ASKED TO PULL OVER BY A FRIEND WHO TOLD ME THE BRAKE LIGHTS WEREN'T ACTIVATING ON THE PASSENGER SIDE OF THE VEHICLE. CENTER AND LEFT SIDE WERE OPERATIONAL. WHEN I TURN OFF THE HEADLIGHTS, THE BRAKE LIGHTS ARE OPERATIONAL. AN OBVIOUS SYSTEM FAILURE WITHIN THE SEALED LIGHT. CANNOT REPLACE THIS LED LIGHT, THE ENTIRE TAIL LAMP UNIT MUST BE REMOVED. CHECKED WITH VARIOUS PARTS AND DEALERSHIP ($400+) SEEMS EXCESSIVE FOR A TAIL LIGHT THAT COSTS $2-3 IN AN ORDINARY TAIL LIGHT SYSTEM. *JS
NHTSA ODI #10579635
23,000 miles · Apr 1, 2014
Exterior Lighting
TL* THE CONTACT OWNS A 2010 MERCURY MILAN. THE CONTACT STATED THAT THE DRIVER'S SIDE REAR TAIL LIGHT FAILED AND REMAINED ILLUMINATED AFTER THE BRAKE PEDAL WAS RELEASED. THE DEALER PERFORMED A DIAGNOSTIC WHICH LOCATED THE FAILURE AT THE LED ASSEMBLY CIRCUIT BOARD. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS MADE AWARE OF T…
Read full complaint
TL* THE CONTACT OWNS A 2010 MERCURY MILAN. THE CONTACT STATED THAT THE DRIVER'S SIDE REAR TAIL LIGHT FAILED AND REMAINED ILLUMINATED AFTER THE BRAKE PEDAL WAS RELEASED. THE DEALER PERFORMED A DIAGNOSTIC WHICH LOCATED THE FAILURE AT THE LED ASSEMBLY CIRCUIT BOARD. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 23,000 AND THE CURRENT MILEAGE WAS 24,500.
NHTSA ODI #10576435
Official recalls
11Mar 10, 2021
Ford Motor Company (Ford) is recalling certain 2007-2011 Ranger, 2006-2012 Fusion, Lincoln Zephyr, Lincoln MKZ, 2006-2011 Mercury Milan, 2007-2010 Ford Edge, and Lincoln MKX vehicles. The driver's side air bag inflator may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will replace the driver-side airbag inflator or module with an alternate one, free of charge. Owner notification letters were mailed on April 9, 2021 for the passenger side, and November 14, 2022 for the driver side. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S12.
Feb 16, 2021
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Additional source detail variants (3)
Air Bags:frontal:passenger Side:inflator Module
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Air Bags:frontal:driver Side:inflator Module
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Air Bags:frontal
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Dec 18, 2019
Ford Motor Company (Ford) is recalling certain 2006-2010 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ vehicles. The valves within the ABS Hydraulic Control Units (HCU) may react with brake fluids containing specific corrosion preventative additives. This reaction may cause the valves to not close properly.
Consequence & remedy
Consequence: If the valves do not properly close, additional brake pedal travel may be required to stop the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will flush the brake system with DOT 4 fluid and install a new brake fluid reservoir cap. In addition, the HCU will be tested to detect a possible stuck valve condition, replacing the HCU as necessary. All services will be performed free of charge. The recall began April 1, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S54.
Jan 7, 2019
Ford Motor Company (Ford) is recalling certain 2014 Ford Mustang vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is recalling certain 2011 Ford Ranger and Mercury Milan vehicles, 2011-2012 Ford Fusion and Lincoln Zephyr/MKZ vehicles and 2011-2014 Ford Mustang vehicles sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Ford is also recalling certain 2010 Ford Edge and Lincoln MKX vehicles, 2010-2011 Ford Ranger and Mercury Milan vehicles, 2010-2012 Ford Fusion and Lincoln Zephyr/MKZ vehicles, and 2010-2014 Ford Mustang vehicles sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 13, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall 19S01.
Nov 1, 2018
Ford Motor Company (Ford) is recalling certain 2010 Ford Fusion, Mercury Milan and 2010-2012 Lincoln MKZ vehicles that previously received a replacement passenger air bag under recall 16V-384, 17V-024 or 18V-046. In the event of a crash requiring deployment of the passenger air bag, the bracket that secures the air bag inflator to the module housing may deform, allowing the gas that inflates the air bag to leak out.
Consequence & remedy
Consequence: If the air bag does not inflate as intended, there is an increased risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began November 21, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S34.
Jan 11, 2018
Ford Motor Company (Ford) is recalling certain 2013 Ford Mustang vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is recalling certain 2010 Ford Edge, Fusion, Mustang and Ranger, Lincoln MKX and Zephyr/MKZ, and Mercury Milan vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Ford is also recalling certain 2009 Ford Edge, Fusion, Mustang and Ranger, Lincoln MKX and Zephyr/MKZ, and Mercury Milan vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
May 31, 2016
Ford Motor Company (Ford) is recalling certain model year 2007-2011 Ford Ranger vehicles, 2006-2011 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2007-2010 Ford Edge, Lincoln MKX vehicles, 2005-2006 Ford GT vehicles, and 2005-2011 Ford Mustang vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Ford is recalling certain model year 2007-2008 Ford Ranger, Edge and Lincoln MKX vehicles, 2006-2008 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2005-2006 Ford GT vehicles and 2005-2008 Ford Mustang vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Any vehicle not included in "Zone A", or "Zone B" is not included in the safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Ford mailed interim letters informing owners that parts are not yet available on July 15, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
Nov 24, 2015
Ford Motor Company (Ford) is recalling certain model year 2010-2011 Ford Fusion vehicles manufactured July 21, 2008, to March 4, 2011, and 2010-2011 Mercury Milan vehicles manufactured July 23, 2008, to December 10, 2010. The affected vehicles have fuel vapor canisters whose purge valves may not operate properly resulting in abnormal pressure changes in the fuel tank.
Consequence & remedy
Consequence: The pressure changes may cause the tank to crack and leak fuel. A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy: Ford will notify owners, and dealers will update the vehicle powertrain control modules and inspect the vehicle for any diagnostic trouble codes (DTCs) for this issue and perform a leak test on the Canister Purge Valve (CPV). The fuel tank will be inspected for cracks. The CPV and fuel tank will be replaced as necessary. These repairs will be performed free of charge. The recall began on January 15, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S34.
Dec 7, 2011
FORD IS RECALLING CERTAIN MODEL YEAR 2010-2011 FORD FUSION AND MERCURY MILAN VEHICLES EQUIPPED WITH 17 INCH STEEL WHEELS AND BUILT FROM APRIL 1, 2009, THROUGH APRIL 30, 2009, AND FROM DECEMBER 1, 2009, THROUGH NOVEMBER 13, 2010. THE WHEEL STUDS MAY FRACTURE, POTENTIALLY CAUSING A WHEEL TO SEPARATE.
Consequence & remedy
Consequence: WHILE DRIVING, MULTIPLE STUD FRACTURES COULD OCCUR AT THE WHEEL LOCATION, AND THE OPERATOR MAY EXPERIENCE VEHICLE VIBRATION AND/OR WHEEL SEPARATION, INCREASING THE RISK OF A CRASH.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT THE REAR BRAKE DISC SURFACE FOR FLATNESS AND REPLACE THE DISCS AS NECESSARY. ADDITIONALLY, THE WHEEL LUG NUTS WILL BE REPLACED ON ALL FOUR WHEELS. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR ABOUT JANUARY 24, 2012. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
May 24, 2010
FORD IS RECALLING CERTAIN MODEL YEAR 2010 FUSION, MILAN, AND ESCAPE VEHICLES MANUFACTURED FROM FEBRUARY 27, THROUGH MARCH 26, 2010. THE PARK ROD GUIDE RETENTION PIN MAY NOT HAVE BEEN PROPERLY INSTALLED WHICH FAILS TO CONFORM TO THE REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 114, "THEFT PROTECTION AND ROLLAWAY PREVENTION".
Consequence & remedy
Consequence: A VEHICLE PARKED WITHOUT AN ENGAGED PARK PAWL AND WITHOUT AN APPLIED PARKING BRAKE MAY HAVE UNINTENDED MOVEMENT WHICH MAY CAUSE A CRASH.
Remedy: FORD WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 28, 2010. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332 AND FOR THE HEARING IMPAIRED CALL 1-800-232-5952 (TDD). REPRESENTATIVES ARE AVAILABLE MONDAY THROUGH FRIDAY: 8:00AM - 5:00PM.
Apr 20, 2010
FORD IS RECALLING CERTAIN MODEL YEAR 2010 FUSION, EXPLORER, EXPLORER SPORT TRAC, AND MERCURY MILAN AND MOUNTAINEER VEHICLES MANUFACTURED BETWEEN DECEMBER 15, 2009 THROUGH FEBRUARY 3, 2010 EQUIPPED WITH FRONT SEAT MANUAL RECLINERS. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 202, "HEAD RESTRAINT." THE RECLINER GEAR PLATE TEETH MAY BE OUT OF DIMENSION SPECIFICATION WHICH COULD RESULT IN LIMITED PAWL TO GEAR PLATE TOOTH ENGAGEMENT.
Consequence & remedy
Consequence: IN THE EVENT OF A CRASH, THE SEATBACK AND HEAD RESTRAINT MAY MOVE REARWARD, INCREASING THE RISK OF INJURY.
Remedy: DEALERS WILL REPLACE THE MANUAL RECLINERS FOR BOTH POWER AND MANUAL SEATS FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE APRIL 30, 2010. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
6PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
EA12009 · Floor Mat Interference With Accelerator
Opened Dec 12, 2012 · Closed Jun 12, 2014
Status: closed (inferred from source dates) · Vehicle Speed Control; Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Additional source detail variants (2)
Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Vehicle Speed Control
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
EA11009 · Wheel Mounting Stud Fracture
Opened Jul 26, 2011 · Closed Jan 20, 2012
Status: closed (inferred from source dates) · Wheels:lugs/nuts/bolts/studs
To date, the agency is aware of 84 consumer complaints and 361 warranty claims related to the alleged defect in the subject vehicles.In total, 382 subject vehicles reportedly experienced one or more wheel stud fractures, resulting in 7 alleged wheel separation incidents.Most of the reported wheel stud fractures occurred on subject vehicles originally equipped with 17 inch diameter steel wheels (368 of 382) as did all 7 alleged wheel separation incidents.Of the 7 alleged wheel separation incidents, 5 reportedly involved a wheel becoming detached from the subject vehicle's rear axle.The subject vehicles are designed with a safety margin that requires validation of proper wheel joint function with one missing lug nut and all other lug nuts at the minimum torque specification.If multiple stud fractures occur at a wheel location, analysis of reports indicates that the operator may observe vehicle vibration. If the vibration is ignored and the vehicle continues to be driven the remaining studs may fracture, resulting in a wheel separation.By letter dated December 5, 2011, the manufacturer notified the agency that it will conduct a safety recall (identified by NHTSA Recall No.11V-574 and Ford Recall No. 11S23) on certain 2010 and 2011 model year Ford Fusion and Mercury Milan vehicles to address the potential for wheel separation.The recall vehicles were originally equipped with 17 inch diameter steel wheels and were built from April 1, 2009, through April 30, 2009, and from December 1, 2009, through November 13, 2010.Approximately 128,616 vehicles are potentially affected as well as approximately 2,940 service steel wheels distributed to authorized Ford dealers.Ford has identified two distinct root causes of wheel stud fracture in the recall vehicles.First, certain steel wheel centers may have been stamped improperly such that the mounting pad lacks the necessary concavity, which reduces the diameter of the outermost radial points of contact with the brake rotor.This reduces the Belleville washer effect, which reduces the clamp load of the joint.Second, the wheel mounting face on certain rear brake discs may have been machined improperly due to a damaged dust boot on a gauge that measures rear brake rotor parallelism (flatness), resulting in a wheel mounting face that is convex.One or both conditions may induce bending fatigue in the wheel studs.Ford's analysis of manufacturing process information showed that one or both of these two conditions may have been out of control during parts of one or both production ranges covered by the recall.Owners will be notified by mail and instructed to take their vehicles to an authorized Ford or Lincoln dealer to have the lug nuts replaced on all four wheels with new lug nuts treated with a proprietary low-friction coating that improves clamp load given the same applied torque value, and to have the rear brake discs inspected for wheel mounting surface flatness and replaced, if required.Ford will instruct dealers to notify customers who purchased service steel wheels, where information is available, to return vehicles for lug nut replacement.Accordingly, this investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers: 10364337, 10373257, 10378953, 10381431, 10389641, 10389940, 10392373, 10395676, 10396577, 10400071, 10402309, 10416653, 10419175, 10419734, 10420116, 10424191, 10432393, 10434188, 10436471, 10438725 and 10440830.
PE11003 · Wheel Stud Fracture
Opened Jan 21, 2011 · Closed Jul 26, 2011
Status: closed (inferred from source dates) · Wheels:lugs/nuts/bolts/studs
On January 21, 2011, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE11-003) to investigate alleged wheel stud fractures in certain model year (MY) 2010 Ford Fusion vehicles.ODI sent the manufacturer an information request letter dated February 8, 2011 and Ford responded by letter dated March 25, 2011.Ford provided a supplemental response by letter dated July 15, 2011.To date, ODI is aware of 29 complaints related to the alleged defect in the subject vehicles, which now include certain MY2010 Mercury Milan vehicles that are the same or substantially similar to the subject Ford Fusion vehicles in regards to the alleged defect.In total, ODI is aware of 4 reported wheel separation incidents related to the alleged defect in the subject vehicles.The manufacturer's investigation into the root cause of the alleged defect is ongoing.Accordingly, this investigation has been upgraded to an Engineering Analysis (EA11-009) to further study the alleged defect.
AQ10001 · Fleet Vehicle Recall Completion Audit
Opened Nov 18, 2010 · Closed Dec 28, 2015
Status: closed (inferred from source dates) · Unknown Or Other
On November 18, 2010, NHTSA's Recall Management Division (RMD) opened an audit query (AQ10-001) to investigate recall remedy completion by rental car companies on safety recall campaigns.It was expected to provide the agency an indication of how completely and how quickly rental car fleets perform necessary recall-related remedies on the vehicles owned and then rented/leased for use on the roadways.RMD queried three (3) major motor vehicle manufacturers (Ford, Chrysler, and General Motors) and requested data regarding completion figures for fifteen (15) discreet safety recalls.Analysis of this data demonstrated that rental car recalls completion was neither complete nor consistent.The rental car companies representing the largest market share in the industry were then queried as to their respective policies for the rental, lease, and sale of vehicles with open recalls.The data and responses from the manufacturers and the rental car companies can be found in the document repository by accessing the ?Associated Documents link above.In December 2015, Congress enacted the Fixing America's Surface Transportation (FAST) Act.One section of the Act prohibits rental car companies from renting, leasing, or selling motor vehicles subject to open safety recalls.With the passage of the FAST Act and its prohibition, there is no continuing need for the agency to investigate rental car recall completions.Accordingly, this investigation is closed.The agency reserves the right to open any future investigations, including audits of individual recalls, or groups of recalls, or rental car companies, to examine more closely safety recalls performance and completion issues in this area.
PE10019 · Accel Pedal Interference - Acc Floormat
Opened May 28, 2010 · Closed Jan 11, 2013
Status: closed (inferred from source dates) · Vehicle Speed Control:accelerator Pedal
Unsecured mats may interfere with accelerator pedal return to idle. A heel blocker in the floor pan provides a platform that may lift an unsecured mat into contact with the pedal. Ford introduced new pedals as a running change early in model year (MY) 2010 vehicles. Analysis of complaints received by ODI and Ford show elevated rates of pedal entrapment incidents in MY 2008 through early 2010 production vehicles. Incidents typically occur following hard pedal applications to pass slower traffic or when merging into faster traffic. Drivers allege continued high engine power after releasing the accelerator pedal and difficulty braking, including reports that the incident was controlled by shifting to neutral or turning the engine off. Drivers and service technicians reference observing evidence of mat interference or note unsecured Ford or aftermarket all weather floor mats in post-incident inspections.Based on information gathered during the Preliminary Evaluation the population being investigated has been narrowed to model years 2008 to 2010.This investigation has been upgraded to an engineering analysis on MY 2008 through early-2010 vehicles (produced through September 2009) to further assess the scope, frequency and safety consequences of the alleged defect.The VOQs associated with the opening of this Engineering Analysis are: 10479693, 10415911, 10379562, 10372674, 10345830, 10342572, 10339330, 10335336, 10334211, 10332233, 10331160, 10329659, 10327597, 10320011, 10232027, 10214131
Illustration