← New search

2013 MERCEDES-BENZ C300

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2013 MERCEDES-BENZ C300 do not stand out strongly from the model-year median of 259.

About this comparison →

How this year compares

Owner complaints by model year

Other model years Selected year
Compare all C300 years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

All reported categories

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

75 reports with mileage · 184 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 99 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Suspension. Review the 67 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 58 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

9 crash reports2 fire reports7 injury reports

What owners actually said

259 reports
Mileage unknown · Oct 20, 2022
Suspension

While driving on highway, started to slowdown on exit. Vehicle rear end felt waiving side to side. Had vehicle checked with local mechanic. Reported rear subframe rusted and split. Advised not to drive & replace the subframe. Visited MB dealer service. Informed it is a known problem and a safety problem. Can repair when part is …

Read full complaint

While driving on highway, started to slowdown on exit. Vehicle rear end felt waiving side to side. Had vehicle checked with local mechanic. Reported rear subframe rusted and split. Advised not to drive & replace the subframe. Visited MB dealer service. Informed it is a known problem and a safety problem. Can repair when part is re-stock in January 2023?? $4,000 + Research online. Plenty reports in forums with same problem. Why there is not a safety recall?

NHTSA ODI #11490134

Mileage unknown · Oct 18, 2022
Suspension

August 30,2022 local Mercedes Benz dealer stated that their inspection found that the rear sub frame was rusted and needed to be replaced (estimated cost $4,699.88). I had two other independent repair shops confirm the sub frame condition.My car had 78,753 miles on it at time of discovery of sub frame corrosion condition. My ind…

Read full complaint

August 30,2022 local Mercedes Benz dealer stated that their inspection found that the rear sub frame was rusted and needed to be replaced (estimated cost $4,699.88). I had two other independent repair shops confirm the sub frame condition.My car had 78,753 miles on it at time of discovery of sub frame corrosion condition. My independent repair shop says that OEM sub frames are back ordered with no estimate of when one would be available. Internet searches and discussion with independent repair shops indicate the rear sub frame corrosion , and structural failures, are a common problem.Structural failures are a serious safety hazard and this defect should be the subject of an NHTSA investigation and recall and replacement by Mercedes Benz. Structural suspension parts should not corrode and fail after only 78,000 miles on cars driven in normal conditions.

NHTSA ODI #11489842

Mileage unknown · Oct 14, 2022
Suspension

The rear suspension frame was rusted, and the suspension rusted off the frame through normal wear and tear (no potholes, incidents, etc). Left side rusted off, Right side is on its way. Brake distance was increased and suddenly braking on the highway resulted in back of car swerving slightly, almost hit a truck that suddenly m…

Read full complaint

The rear suspension frame was rusted, and the suspension rusted off the frame through normal wear and tear (no potholes, incidents, etc). Left side rusted off, Right side is on its way. Brake distance was increased and suddenly braking on the highway resulted in back of car swerving slightly, almost hit a truck that suddenly merged into my lane. This was discovered during an MD state inspection, I called 6 dealerships in the area, and all were familiar with the issue with this chassis. I got two estimates saying the same problem. This forum shows that there are many more like me, and even in the UK dealerships are doing replacement free of charge due to how widespread it is: https://www.benzworld.org/threads/w204-rear-subframes-deterioration.3048088/ The part has not been inspected by the manufacturer/police/insurance inspector. There were no warning lights or any alerts on my dash indicating this issue, I only found out bc I just so happened to need to do an MD state inspection, and I had been hearing a squeaking noise. Also, my brake distance was longer, and my car swerved a little under sudden braking on a dry sunny day.

NHTSA ODI #11489258

95,000 miles · Oct 13, 2022
Suspension

The contact owns a 2013 Mercedes-Benz C300. The contact stated while driving approximately 65 MPH, the vehicle started shuddering inadvertently, almost causing the contact to lose control of the steering wheel. The contact was able to veer to the side of the road. The vehicle was towed to a certified independent mechanic who di…

Read full complaint

The contact owns a 2013 Mercedes-Benz C300. The contact stated while driving approximately 65 MPH, the vehicle started shuddering inadvertently, almost causing the contact to lose control of the steering wheel. The contact was able to veer to the side of the road. The vehicle was towed to a certified independent mechanic who diagnosed that the driver's side rear subframe was severely corroded and fractured. The vehicle was not repaired. The dealer was not notified of the failure. The manufacturer was made aware of the failure and a case was opened. The approximate failure mileage was 95,000.

NHTSA ODI #11489102

Mileage unknown · Sep 27, 2022
StructureSuspension

Rear subframe cracked; car has less than 95,000 miles and looks great. My two children of driving age were using the vehicle at the time, driving others as well. Fortunately, I happened to drive it not longer after the issue and took it to the shop immediately. They put it on the lift and saw that the rear subframe was cracked a…

Read full complaint

Rear subframe cracked; car has less than 95,000 miles and looks great. My two children of driving age were using the vehicle at the time, driving others as well. Fortunately, I happened to drive it not longer after the issue and took it to the shop immediately. They put it on the lift and saw that the rear subframe was cracked all the way through. As it turns out, it is becoming very common on this make/model--and it is nearly impossible to get a replacement. Mercedes Benz told me maybe sometime in 2023. In addition to having it inspected, I have since been in contact with several dealers and mechanics. Results are invariable: the part is in extremely high demand, Mercedes cannot fill the demand, and the wait is indefinite but long. There were no warning lamps, messages or other symptoms of the problem. In addition to the inconvenience, the car was very dangerous to drive. I am thankful that my son did not seriously injure himself or others while driving. The crack renders the car unstable at anything but the slowest speeds. When one brakes at any speed over about 20-25 mph, the car pulls violently to one side. Simply braking alone could cause a major, even fatal, accident. And any emergency maneuver could be disastrous. The car has been garaged since June awaiting a replacement that I am told will cost between $4000 and $6000! I am left with a vehicle that runs very well--but is unsafe to drive on a public roadway--and no way to repair it. Moreover, Mercedes cannot tell me when the part may become available (likely sometime in 2023).

NHTSA ODI #11486805

Mileage unknown · Sep 24, 2022
Service BrakesSteeringStructure

Rear subframe of vehicle rusted under regular use conditions and the left trailing arm mount broke off as a result. This caused vehicle braking to become extremely unstable and dangerous, even at low/medium speed. This is a known problem from this manufacturer and the Fed government should take action to force recall.

NHTSA ODI #11486195

Mileage unknown · Sep 19, 2022
SuspensionUnknown Or Other

Brought my car to the dealership because I was hearing a noise when going over bumps. Also noticed some instability when braking and driving at highway speeds. Dealer informed my my subframe had rusted and told me the car was unsafe to drive.

NHTSA ODI #11485232

89,000 miles · Sep 14, 2022
Structure

The contact owns a 2013 Mercedes-Benz C300. The contact stated that while the vehicle was at the dealer for routine maintenance, the dealer informed him that the subframe was corroded and needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately…

Read full complaint

The contact owns a 2013 Mercedes-Benz C300. The contact stated that while the vehicle was at the dealer for routine maintenance, the dealer informed him that the subframe was corroded and needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 89,000.

NHTSA ODI #11484447

Mileage unknown · Sep 10, 2022
EngineStructure

rear subframe premature rust for a 2013 car I've been reading a lot many people have same problem it is a very expensive fix and I'm sure Mercedes knows about it. Also engine makes very bad rattling noise at startup which is also a very expensive fix and Mercedes issued a tsb bulletin thank you

NHTSA ODI #11483845

118,000 miles · Sep 8, 2022
Suspension

The contact owns a 2013 Mercedes-Benz C300. The contact stated that while driving approximately 55 mph when they attempted to apply the brake pedal but the vehicle failed to stop and emitted a rumbling noise. The contact stated the vehicle's rear end had swerved causing them to use excessive force in order to avoid a crash. The …

Read full complaint

The contact owns a 2013 Mercedes-Benz C300. The contact stated that while driving approximately 55 mph when they attempted to apply the brake pedal but the vehicle failed to stop and emitted a rumbling noise. The contact stated the vehicle's rear end had swerved causing them to use excessive force in order to avoid a crash. The contact was able to maneuver the vehicle to the side of the road where they waited before continuing driving. There were no warning lights. The contact took the vehicle to the dealer who diagnosed that the rear subframe on the driver's side had severe rust and needed to be replaced. The vehicle had not been repaired. The manufacturer was not made aware of the failure. The approximate failure mileage was 118,000.

NHTSA ODI #11483528

Official recalls

6

19V787000 · Communication

Nov 1, 2019

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit: https://static.nhtsa.gov/odi/rcl/2019/RMISC-19V787-4620.pdf

Consequence & remedy

Consequence: An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.

Remedy: MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.

19V010000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2019

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014 C250, C300 4Matic, C350, C63 AMG, E350 4Matic Coupe, E350 Cabrio, E350 Coupe, SLS AMG Cabrio, SLS AMG Coupe, 2014-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, GLK 350, GLK250 BlueTec 4Matic, GLK350 RWD, 2015-2017 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2014-2017 E550 Cabrio, and 2014-2016 E550 Coupe vehicles sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally, MBUSA is recalling certain 2012-2014 C250, E350 4Matic Coupe, SLS AMG Cabrio, 2012-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, 2011 C300, 2011-2014 C300 4Matic, C350, C63 AMG, E350 Cabrio, E350 Coupe, SLS AMG Coupe, 2015-2016 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2011-2016 E550 Cabrio, E550 Coupe, 2011-2015 GLK350 4Matic, GLK350 RWD, and 2013-2015 GLK250 BlueTec 4Matic vehicles ever registered in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." MBUSA is also recalling certain 2012-2014 C250, E350 4Matic Coupe, SLS AMG Cabrio 2012-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, 2010-2011 C300, 2010-2014 C300 4Matic, C350, C63 AMG, E350 Coupe, 2011-2014 E350 Cabrio, SLS AMG Coupe, 2015-2016 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2016-2017 E550 Cabrio, 2010-2016 E550 Coupe, 2010-2015 GLK350 4Matic, GLK350 RWD, and 2013-2015 GLK250 BlueTec 4Matic vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MO, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI and WY or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the passenger or other occupants resulting in serious injury or death.

Remedy: MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372.

18V043000 · Air Bags:frontal:passenger Side:inflator Module

Jan 10, 2018

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2013 C250, C250 Coupe, C350 Coupe 4Matic, C300 4Matic, C350, C350 Coupe, C63 AMG, C63 Coupe, E350 Cabrio, E350 Coupe, E550 Cabrio, E350 Coupe 4Matic, E550 Coupe, GLK350 4Matic, GLK250 Bluetec 4Matic, GLK350, SLS Coupe, SLS AMG GT Coupe, and SLS Roadster vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, MBUSA is recalling certain 2010 C300, C300 4Matic, C63 AMG, E350 Coupe, E550 Coupe, GLK350, and GLK350 4Matic vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." MBUSA is also recalling certain 2009 C300, C300 4Matic, C63 AMG, and C350 vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MO, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI and WY or "Zone C." In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. Mercedes issued an interim notification to owners on February 23, 2018. A second notice will be mailed when remedy parts are available. Owners may contact MBUSA customer service at 1-877-496-3691.

17V627000 · Air Bags:frontal

Oct 6, 2017

Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec, GLK350, GLK350 4Matic, 2016-2017 C350e, C43 AMG, 2015 C400 4Matic, 2016-2018 C63 AMG, GLC300, GLC300 4Matic, 2017-2018 C300 Coupe, C300 4Matic Coupe, C43 AMG, C63 AMG Coupe, C63S AMG Coupe, C300 Cabriolet, C300 4Matic Cabriolet, C43 AMG Cabriolet, C63 AMG Cabriolet, C63S AMG Cabriolet, GLC300 4Matic Coupe, GLC43 AMG, GLC43 AMG Coupe, 2014 E350 Coupe, E350 4Matic Coupe, E350 Cabriolet, E400 Hybrid, 2015-2017 E400 Coupe, E400 4Matic Coupe, E400 Cabriolet, 2014-2017 E550 Coupe, E550 Cabriolet, B250e, 2014-2016 E250 BlueTec, E63 AMG 4Matic Wagon, 2012-2013 E350 BlueTec, 2012-2016 E350, E350 4Matic, 2015-2016 E400, E400 4Matic, 2012 E63 AMG, 2014-2015 E250 4Matic BlueTec, 2013-2016 E350 Wagon, 2017 GLC300d 4Matic, and 2018 GLC350e 4Matic. The driver's air bag may unexpectedly deploy due to insufficient grounding of the steering components if an electrostatic discharge occurs and the air bag clockspring is broken.

Consequence & remedy

Consequence: If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.

Remedy: MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.

17V252000 · Steering

Apr 12, 2017

Mercedes-Benz USA LLC. (MBUSA) is recalling certain 2013-2014 C250, C300 4MATIC, GLK250 4MATIC BLUETEC and GLK350 vehicles, 2013 C250 Coupe, C350, C350 4MATIC Coupe, C350 Coupe and C63 AMG Coupe vehicles, and 2013-2015 GLK350 4MATIC vehicles. The steering coupling connecting bolt may have been insufficiently tightened, possibly resulting in a loss of steering.

Consequence & remedy

Consequence: A loss of steering can increase the risk of a crash.

Remedy: MBUSA will notify owners, and dealers will inspect the steering coupling connecting bolt, tightening it as necessary, free of charge. The recall began May 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

17V177000 · Air Bags:frontal:sensor/control MODULE-INACTIVE ; Electrical System:software

Mar 14, 2017

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550 4Matic vehicles, 2012-2016 E350 vehicles, 2016-2017 GL450 4Matic vehicles, 2012-2014 ML350 4Matic BlueTec vehicles, 2015 S550, S550 4Matic and C300 4Matic Sedan vehicles, 2015-2016 C300 Sedan vehicles, and 2017 SL63 AMG vehicles. Various control units on these vehicles may have been updated with incorrect software, potentially affecting the correct deployment of the air bags in the event of a crash.

Consequence & remedy

Consequence: If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.

Remedy: MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

Additional source detail variants (2)

Electrical System:software

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550 4Matic vehicles, 2012-2016 E350 vehicles, 2016-2017 GL450 4Matic vehicles, 2012-2014 ML350 4Matic BlueTec vehicles, 2015 S550, S550 4Matic and C300 4Matic Sedan vehicles, 2015-2016 C300 Sedan vehicles, and 2017 SL63 AMG vehicles. Various control units on these vehicles may have been updated with incorrect software, potentially affecting the correct deployment of the air bags in the event of a crash.

Consequence: If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.

Remedy: MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

Air Bags:frontal:sensor/control MODULE-INACTIVE

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550 4Matic vehicles, 2012-2016 E350 vehicles, 2016-2017 GL450 4Matic vehicles, 2012-2014 ML350 4Matic BlueTec vehicles, 2015 S550, S550 4Matic and C300 4Matic Sedan vehicles, 2015-2016 C300 Sedan vehicles, and 2017 SL63 AMG vehicles. Various control units on these vehicles may have been updated with incorrect software, potentially affecting the correct deployment of the air bags in the event of a crash.

Consequence: If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.

Remedy: MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.