← New search

2012 MERCEDES-BENZ C300

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2012 MERCEDES-BENZ C300 do not stand out strongly from the model-year median of 259.

About this comparison →

When problems were reported

Mileage at the reported incident

74 reports with mileage · 192 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 114 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Suspension. Review the 69 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 54 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

5 crash reports4 fire reports5 injury reports

What owners actually said

266 reports
Mileage unknown · Feb 26, 2022
Suspension

Rear subframe failure caused me to loose control of vehicle almost resulting in a serious highway accident. Rear driver side stabilizer subframe mount was completely corroded and broken away from the subframe. There is no other significant corrosion on the subframe. MB claim normal corrosion however the pictures tell a differ…

Read full complaint

Rear subframe failure caused me to loose control of vehicle almost resulting in a serious highway accident. Rear driver side stabilizer subframe mount was completely corroded and broken away from the subframe. There is no other significant corrosion on the subframe. MB claim normal corrosion however the pictures tell a different story.

NHTSA ODI #11454235

Mileage unknown · Feb 24, 2022
Suspension

While performing service inspection, technician found REAR SUB FRAME RUSTED AND READY TO BREAK. Told they needed to show me the problem on the lift, as it was a serious SAFETY ISSUE and should be IMMEDIATELY REPLACED. Dealer and service acknowledged that this is a KNOWN and WIDESPREAD PROBLEM in C Class vehicles. Cost to repl…

Read full complaint

While performing service inspection, technician found REAR SUB FRAME RUSTED AND READY TO BREAK. Told they needed to show me the problem on the lift, as it was a serious SAFETY ISSUE and should be IMMEDIATELY REPLACED. Dealer and service acknowledged that this is a KNOWN and WIDESPREAD PROBLEM in C Class vehicles. Cost to replace quoted at $4200. No warning - thankfully inspection found before I was in a serious accident! Mercedes should issue recall for failed/corroded frame. Not the "safe" vehicle that Mercedes claims. (Car has been dealer serviced regularly, garaged, and 34,000 miles.) Owners shouldn't have to suddenly come up with $4,200 in order to drive their seemingly normal car. DANGEROUS.

NHTSA ODI #11453890

Mileage unknown · Feb 14, 2022
Structure

Per the dealership in connection with a regular service, the rear subframe rusted out and became structurally weak and was a safety hazard. The problem was confirmed and repaired by an independent repair shop. From Google searches, this issue does not appear to be an uncommon problem. Car is garaged and receives regular underb…

Read full complaint

Per the dealership in connection with a regular service, the rear subframe rusted out and became structurally weak and was a safety hazard. The problem was confirmed and repaired by an independent repair shop. From Google searches, this issue does not appear to be an uncommon problem. Car is garaged and receives regular underbody washes for road salt.

NHTSA ODI #11451935

Mileage unknown · Jan 24, 2022
Electrical SystemSteering

While driving, engine stopped, could not steer.. Looks like a defective Electronic Ignition Switch or steering lock! It seems to be a common problem on these cars!!! The car would not start. After 8 attempts, I was able to start car but was afraid to drive it. Could have been a disaster.

NHTSA ODI #11448715

Mileage unknown · Jan 7, 2022
Structure

This is a followup to a previous report. I now have photos and the actual part that was replaced. While driving on secondary road at 45 mph, braked for stoplight in 2012 Mercedes C300 4matic. Car veered left, rear swung right, and right front dove downward. Luckily regained control and prevented swerving into oncoming traffic…

Read full complaint

This is a followup to a previous report. I now have photos and the actual part that was replaced. While driving on secondary road at 45 mph, braked for stoplight in 2012 Mercedes C300 4matic. Car veered left, rear swung right, and right front dove downward. Luckily regained control and prevented swerving into oncoming traffic. Took car to my regular mechanic and it was determined that the welds on the left rear portion of the rear subframe had rusted out from the inside of the subframe, severing the attachment to the left rear wheel control arms. The car had been inspected 6 months earlier and there was no sign of problem. The failure was catastrophic, not gradual. Upon removal, it was also noted that the right mounting bracket was also in the process of rusting through and failing. When the mechanic called the local Mercedes dealer, the service manager was not surprised and proceeded to outline what parts would be needed to carry out the repair. When I contacted the local Mercedes dealer, myself, they said this wasn’t an uncommon problem, but there was not recall or service bulletin on the problem. Was given a rough quote of $5000 to affect the repair. I also contacted Mercedes Benz USA and was told there were no recalls or service bulletins, but they might be able to provide some “Goodwill Assistance” to offset the expected cost if I had it towed to a MB dealer and got a quote from them. Benzworld.org, an owners forum with over 5 million participants world-wide https://www.benzworld.org/threads/w204-rear-subframes-deterioration.3048088/#post-17965564 has multiple postings about the problem as do other forums including CarProblemZoo.com https://www.carproblemzoo.com/mercedesbenz/c300/suspension-problems.php . This design/manufacturer defect has had recalls in both Europe and Canada. Why this is not being addressed in the US? This sudden failure is potentially life-threatening.

NHTSA ODI #11446590

Mileage unknown · Dec 30, 2021
Suspension

The rear subframe rusted through causing mounting point of the torque link to fail. As a result, the car looses control when braking going sideways. Luckily, I discovered it when testing brakes after pad replacement in a safe setting. To my understanding, there are many other W204/W212 cars affected in the US with that issue. Me…

Read full complaint

The rear subframe rusted through causing mounting point of the torque link to fail. As a result, the car looses control when braking going sideways. Luckily, I discovered it when testing brakes after pad replacement in a safe setting. To my understanding, there are many other W204/W212 cars affected in the US with that issue. Mercedes so far does not want to take responsibility and recall cars for this issue which is a huge concern.

NHTSA ODI #11445555

Mileage unknown · Dec 16, 2021
Air BagsElectrical System

3 signal Signal light comes one saying abs, another SRS MALFUNCTION, also crushed control inoperable. Car will come one as normal next day car comes on no lights not 1 button work turn signals didn’t work then my car fan came on in the engines the also the when they the electric isn’t working i have to manually shift the gear

NHTSA ODI #11443966

43,000 miles · Dec 13, 2021
Structure

The contact's wife owns a 2012 Mercedes-Benz C300. The contact stated that upon taking the vehicle to the dealer to be serviced, he was informed that the subframe was severely corroded and could fracture. The manufacturer was notified of the failure and advised the contact that they could not assist as the vehicle was out of war…

Read full complaint

The contact's wife owns a 2012 Mercedes-Benz C300. The contact stated that upon taking the vehicle to the dealer to be serviced, he was informed that the subframe was severely corroded and could fracture. The manufacturer was notified of the failure and advised the contact that they could not assist as the vehicle was out of warranty. The vehicle was not repaired. The approximate failure mileage was 43,000.

NHTSA ODI #11443648

Mileage unknown · Nov 26, 2021
Structure

While driving on secondary road at 45 mph, braked for stoplight in 2012 Mercedes C300 4matic. Car veered left, rear swung right, and right front dove downward. Luckily regained control and prevented swerving into oncoming traffic. Took car to my regular mechanic and it was determined that the welds on the left rear portion of…

Read full complaint

While driving on secondary road at 45 mph, braked for stoplight in 2012 Mercedes C300 4matic. Car veered left, rear swung right, and right front dove downward. Luckily regained control and prevented swerving into oncoming traffic. Took car to my regular mechanic and it was determined that the welds on the left rear portion of the rear subframe had rusted out from the inside of the subframe, severing the attachment to the left rear wheel control arms. The car had been inspected 6 months earlier and there was no sign of problem. The failure was catastrophic, not gradual. When the mechanic called the local Mercedes dealer, the service manager was not surprised and proceeded to outline what parts would be needed to carry out the repair. When I contacted the local Mercedes dealer, myself, they said this wasn’t an uncommon problem, but there was not recall or service bulletin on the problem. Was given a rough quote of $5000 to affect the repair. I also contacted Mercedes Benz USA and was told there were no recalls or service bulletins, but they might be able to provide some “Goodwill Assistance” to offset the expected cost if I had it towed to a MB dealer and got a quote from them. Benzworld.org, an owners forum with over 5 million participants world-wide https://www.benzworld.org/threads/w204-rear-subframes-deterioration.3048088/#post-17965564 has multiple postings about the problem as do other forums including CarProblemZoo.com https://www.carproblemzoo.com/mercedesbenz/c300/suspension-problems.php . This design/manufacturer defect has had recalls in both Europe and Canada. Why this is not being addressed in the US? This sudden failure is potentially life-threatening.

NHTSA ODI #11441743

115,000 miles · Nov 23, 2021
Structure

The contact owns a 2012 Mercedes-Benz C300. The contact stated her son was driving approximately 60 MPH and noticed that the steering wheel was crooked and vibrating. The driver was manually turning the steering wheel for the vehicle to drive straight. The driver also noticed that while depressing the brake pedal, the rear of th…

Read full complaint

The contact owns a 2012 Mercedes-Benz C300. The contact stated her son was driving approximately 60 MPH and noticed that the steering wheel was crooked and vibrating. The driver was manually turning the steering wheel for the vehicle to drive straight. The driver also noticed that while depressing the brake pedal, the rear of the vehicle was shaking going from left to right while coming to a complete stop. The driver took the vehicle to an independent mechanic to be inspected and was informed that the rear driver’s side subframe had separated from the vehicle due to extreme rust. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 115,000.

NHTSA ODI #11441459

Official recalls

6

20V298000 · Air Bags:frontal:passenger Side:inflator Module

May 22, 2020

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012 C250, C250 Coupe, C300, C350, C350 Coupe, C63 AMG, and C63 AMG Coupe vehicles equipped with a front passenger air bag assembly replaced under a prior recall. An incorrect replacement front passenger air bag may have been installed.

Consequence & remedy

Consequence: An incorrect passenger air bag may not provide adequate protection, increasing the risk of injury in the event of a crash.

Remedy: MBUSA will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began July 10, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020060011.

19V010000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2019

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014 C250, C300 4Matic, C350, C63 AMG, E350 4Matic Coupe, E350 Cabrio, E350 Coupe, SLS AMG Cabrio, SLS AMG Coupe, 2014-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, GLK 350, GLK250 BlueTec 4Matic, GLK350 RWD, 2015-2017 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2014-2017 E550 Cabrio, and 2014-2016 E550 Coupe vehicles sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally, MBUSA is recalling certain 2012-2014 C250, E350 4Matic Coupe, SLS AMG Cabrio, 2012-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, 2011 C300, 2011-2014 C300 4Matic, C350, C63 AMG, E350 Cabrio, E350 Coupe, SLS AMG Coupe, 2015-2016 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2011-2016 E550 Cabrio, E550 Coupe, 2011-2015 GLK350 4Matic, GLK350 RWD, and 2013-2015 GLK250 BlueTec 4Matic vehicles ever registered in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." MBUSA is also recalling certain 2012-2014 C250, E350 4Matic Coupe, SLS AMG Cabrio 2012-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, 2010-2011 C300, 2010-2014 C300 4Matic, C350, C63 AMG, E350 Coupe, 2011-2014 E350 Cabrio, SLS AMG Coupe, 2015-2016 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2016-2017 E550 Cabrio, 2010-2016 E550 Coupe, 2010-2015 GLK350 4Matic, GLK350 RWD, and 2013-2015 GLK250 BlueTec 4Matic vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MO, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI and WY or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the passenger or other occupants resulting in serious injury or death.

Remedy: MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372.

17V627000 · Air Bags:frontal

Oct 6, 2017

Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec, GLK350, GLK350 4Matic, 2016-2017 C350e, C43 AMG, 2015 C400 4Matic, 2016-2018 C63 AMG, GLC300, GLC300 4Matic, 2017-2018 C300 Coupe, C300 4Matic Coupe, C43 AMG, C63 AMG Coupe, C63S AMG Coupe, C300 Cabriolet, C300 4Matic Cabriolet, C43 AMG Cabriolet, C63 AMG Cabriolet, C63S AMG Cabriolet, GLC300 4Matic Coupe, GLC43 AMG, GLC43 AMG Coupe, 2014 E350 Coupe, E350 4Matic Coupe, E350 Cabriolet, E400 Hybrid, 2015-2017 E400 Coupe, E400 4Matic Coupe, E400 Cabriolet, 2014-2017 E550 Coupe, E550 Cabriolet, B250e, 2014-2016 E250 BlueTec, E63 AMG 4Matic Wagon, 2012-2013 E350 BlueTec, 2012-2016 E350, E350 4Matic, 2015-2016 E400, E400 4Matic, 2012 E63 AMG, 2014-2015 E250 4Matic BlueTec, 2013-2016 E350 Wagon, 2017 GLC300d 4Matic, and 2018 GLC350e 4Matic. The driver's air bag may unexpectedly deploy due to insufficient grounding of the steering components if an electrostatic discharge occurs and the air bag clockspring is broken.

Consequence & remedy

Consequence: If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.

Remedy: MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.

17V177000 · Air Bags:frontal:sensor/control MODULE-INACTIVE ; Electrical System:software

Mar 14, 2017

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550 4Matic vehicles, 2012-2016 E350 vehicles, 2016-2017 GL450 4Matic vehicles, 2012-2014 ML350 4Matic BlueTec vehicles, 2015 S550, S550 4Matic and C300 4Matic Sedan vehicles, 2015-2016 C300 Sedan vehicles, and 2017 SL63 AMG vehicles. Various control units on these vehicles may have been updated with incorrect software, potentially affecting the correct deployment of the air bags in the event of a crash.

Consequence & remedy

Consequence: If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.

Remedy: MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

Additional source detail variants (2)

Electrical System:software

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550 4Matic vehicles, 2012-2016 E350 vehicles, 2016-2017 GL450 4Matic vehicles, 2012-2014 ML350 4Matic BlueTec vehicles, 2015 S550, S550 4Matic and C300 4Matic Sedan vehicles, 2015-2016 C300 Sedan vehicles, and 2017 SL63 AMG vehicles. Various control units on these vehicles may have been updated with incorrect software, potentially affecting the correct deployment of the air bags in the event of a crash.

Consequence: If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.

Remedy: MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

Air Bags:frontal:sensor/control MODULE-INACTIVE

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550 4Matic vehicles, 2012-2016 E350 vehicles, 2016-2017 GL450 4Matic vehicles, 2012-2014 ML350 4Matic BlueTec vehicles, 2015 S550, S550 4Matic and C300 4Matic Sedan vehicles, 2015-2016 C300 Sedan vehicles, and 2017 SL63 AMG vehicles. Various control units on these vehicles may have been updated with incorrect software, potentially affecting the correct deployment of the air bags in the event of a crash.

Consequence: If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.

Remedy: MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

17V017000 · Air Bags:frontal:passenger Side:inflator Module

Jan 10, 2017

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2012 C300 4Matic, C250, C250 Coupe, C350, C350 Coupe 4Matic, C350 Coupe, C63 AMG, C63 AMG Coupe, E350 Coupe 4Matic, E350 Cabrio, E350 Coupe, E550 Cabrio, E550 Coupe, GLK350 4Matic, GLK350, SLS AMG Cabrio, and SLS AMG Coupe vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above MBUSA is recalling certain 2009 C300 4Matic, C300, C350 and C63 AMG vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above MBUSA is recalling certain 2008 C300 4Matic, C300, and C350 vehicles originally sold, or ever registered, in Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: MBUSA will notify owners, and dealers will replace the front passenger air bag modules, free of charge. Owners were sent an interim notification in March 2017. Second notices started going out in October 2018 and continue to be mailed as parts become available. Owners may contact MBUSA customer service at 1-877-496-3691

12V557000 · Fuel System, Gasoline

Dec 3, 2012

Mercedes-Benz is recalling certain model year 2011-2012 S400, S550, S550 4Matic, S63 AMG, C300, C300 4Matic, E350, GLK350, GLK350 4Matic, CL550 4Matic, and CL63 AMG vehicles manufactured from April 18, 2011, through July 12, 2011. Due to an irregularity stemming from the molding process of the fuel filter flange, the fuel filter flange may crack when operated in high temperatures.

Consequence & remedy

Consequence: If the fuel filter flange cracks, it will leak fuel which may lead to a fire if an external ignition source is present.

Remedy: Mercedes-Benz will notify owners, and dealers will replace the fuel filter, free of charge. The recall campaign is expected to begin in February 2013. Owners may contact Mercedes-Benz at 1-800-367-6372.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.