IllustrationDASH BOARD BRAKE LIGHT WENT ON AND THE BRAKES FAILED. *LA
2002 Mercedes Benz ML320
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2002 Mercedes Benz ML320 do not stand out strongly from the model-year median of 28.
About this comparison →How this year compares
Owner complaints by model year
Compare all ML320 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
100–25K
525–50K
1150–75K
1175–100K
20100–150K
9150K+
66 reports with mileage · 22 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 24 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 19 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 15 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
4 crash reports8 fire reports5 injury reports
What owners actually said
88 reportsTHIS VEHICLE HAS NUMEROUS DEFECTS, AND HAS BEEN IN FOR SERVICE COUNTLESS AMOUNTS OF TIMES. MB PROMISED TO REPLACE THE VEHICLE IF THEIR FACTORY REPRESENTATIVE COULD VERIFY MY COMPLAINTS. THEY ABSOLUTELY FOUND NUMEROUS, REDUNDANT DEFECTS AND NOW ONLY WANT TO FIX THE VEHICLE, RATHER THAT REPLACE THE VEHICLE. WHAT A BUNCH OF LIARS. …
Read full complaint
THIS VEHICLE HAS NUMEROUS DEFECTS, AND HAS BEEN IN FOR SERVICE COUNTLESS AMOUNTS OF TIMES. MB PROMISED TO REPLACE THE VEHICLE IF THEIR FACTORY REPRESENTATIVE COULD VERIFY MY COMPLAINTS. THEY ABSOLUTELY FOUND NUMEROUS, REDUNDANT DEFECTS AND NOW ONLY WANT TO FIX THE VEHICLE, RATHER THAT REPLACE THE VEHICLE. WHAT A BUNCH OF LIARS. THE VEHICLE HAS ISSUES WITH THE STEERING SYSTEM, THE WHEEL RUBS AND THE POWER STEERING FADES OUT, THE RADIO AND CD CHANGER MALFUNCTION CONSTANTLY, FUMES FROM THE VENTILATION SYSTEM, AND WHEN YOU HIT A BUMP, THE CAR ALMOST GOES OUT OF CONTROL, EVEN THE ESP LIGHT COMES ON. *JB
EMERGENCY BRAKES FAILED TO RELEASE UNLESS STEPPED ON GAS TO FORWARD OR REVERSE. A DAY LATER AFTER WHEELS WERE WASHED AND DRIED UP, EMERGENCY BRAKES WOULD NOT RELEASE TOTALLY UNTIL STEPPING ON THE GAS PEDAL. YOU CAN HEAR A LOUD NOISE(FEEL LIKE HITTING YOUR BUMPER TO SOMETHING) WHEN STEPPING ON THE GAS PEDAL DURING THE RELEASE OF …
Read full complaint
EMERGENCY BRAKES FAILED TO RELEASE UNLESS STEPPED ON GAS TO FORWARD OR REVERSE. A DAY LATER AFTER WHEELS WERE WASHED AND DRIED UP, EMERGENCY BRAKES WOULD NOT RELEASE TOTALLY UNTIL STEPPING ON THE GAS PEDAL. YOU CAN HEAR A LOUD NOISE(FEEL LIKE HITTING YOUR BUMPER TO SOMETHING) WHEN STEPPING ON THE GAS PEDAL DURING THE RELEASE OF THE BRAKES. LOCAL DEALER SAID THEIR REGIONAL TECHNICIAN TOLD THEM THAT THIS WAS NORMAL. IT'S MY REPSONSIBILITY TO DRIVE THE CAR UNTIL THE BRAKE PADS ARE DRIED UP, THEN PARK THE CAR. I TOLD THEM IT IS DANGEROUS FOR SOMEONE WHO MAY NOT KNOW AND THOUGHT THE CAR WON'T MOVE AND STEP ON THE GAS EXCESSIVELY. THEY DID NOT SEEM CARE. I CAN NOT BELIEVE THAT THEY TOLD ME THE PADS HAVE TO BE DRIED UP BEFORE PARKING. I TOLD THEM SERVERAL TIMES SINCE I BOUGHT THE CAR AND THEY COULD NOT REPRODUCE THE PROBLEM UNTIL I CALLED THEIR ROADSIDE ASSISTANCE AND CAME TO MY HOUSE TO VERIFY IT. THEY EVENTUALLY CONFIRMED THE PROBLEM AND REPRODUCED THE PROBLEM AT THEIR SHOP. HOWEVER, THEY DID NOT SEEM TO COMEUP WITH A SOLUTION EXCEPT TO TELL ME THAT IT'S MY REPSONSIBILITY TO DRIVE THE CAR UNTIL THE PADS ARE DRIED UP BEFORE I PARK THE CAR. *AK
WHILE DRIVING, THE STEERING WHEEL LOCKED UP, WHICH CAUSED THE CONSUMER TO VEER OFF TO THE SHOULDER AND INTO AN EMBANKMENT. *JB
MY POWER STEERING WENT OUT AFTER MAKING A SLOW, 180 DEGREE TURN WHEN EXITING A CAR WASH--I WAS TURNING INTO THE STREET WHEN I NOTICED IT. I WAS TOLD THE VEHICLE HAD BEEN RECALLED TO REPLACE THE POWER STEERING PART. I NEVER RECEIVED A RECALL NOTICE (THAT I CAN REMEMBER) AND I HAVE HAD THE CAR IN FOR SERVICE AND THIS WAS NOT POI…
Read full complaint
MY POWER STEERING WENT OUT AFTER MAKING A SLOW, 180 DEGREE TURN WHEN EXITING A CAR WASH--I WAS TURNING INTO THE STREET WHEN I NOTICED IT. I WAS TOLD THE VEHICLE HAD BEEN RECALLED TO REPLACE THE POWER STEERING PART. I NEVER RECEIVED A RECALL NOTICE (THAT I CAN REMEMBER) AND I HAVE HAD THE CAR IN FOR SERVICE AND THIS WAS NOT POINTED OUT. THE SITUATION COULD HAVE CAUSE AN ACCIDENT IF THERE HAD BEEN TRAFFIC COMING IN EITHER LANE. I HAD THREE KIDS IN THE CAR WITH ME. *NLM
WHILE DRIVING BETWEEN 40 AND 60 MPH THE ENTIRE BODY OF THE VEHICLE SHOOK. *NLM
THE VEHICLE EXPERIENCED SIDE MIRROR PROBLEMS.*AK *JB
WHILE DRIVING OUR 2001 MERCEDES BENX ML320, MY WIFE EXPIERENCED SUDDEN LOSS OF STEERING AND WAS THROWN OFF THE ROAD.
Official recalls
101V290000 · Suspension:front:control Arm:upper Arm
Sep 10, 2001
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LEFT FRONT UPPER CONTROL ARM MAY NOT MEET THE SPECIFIED STRENGTH REQUIREMENTS.
Consequence & remedy
Consequence: THE CONTROL ARM COULD FAIL, INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL REPLACE THE LEFT FRONT UPPER CONTROL ARM. OWNER NOTIFICATION BEGAN SEPTEMBER 29, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT MERCEDES-BENZ AT 1-800-367-6372.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10050 · Brake Lamp Switch Failure.
Opened Dec 21, 2010 · Closed May 4, 2011
Status: closed (inferred from source dates) · Exterior Lighting:brake Lights:switch; Service Brakes, Hydraulic; Vehicle Speed Control; Vehicle Speed Control:cruise Control
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed
Additional source detail variants (4)
Exterior Lighting:brake Lights:switch
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed
Service Brakes, Hydraulic
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed
Vehicle Speed Control:cruise Control
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed
Vehicle Speed Control
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed