MY ML 320 YEAR 2000 MERCEDES-BENZ STOPPED SUDDENLY WHILE I WAS GOING 30 MILES AND HOUR. NO SIGN OF ANY PROBLEM (THAN ENGINE STALLED). THIS IS SCARY AND MUST BE INVESTIGATED. I ALMOST HIT A CAR. IT DID NOT START FOR 20 MINUTES AND THEN IT STARTED. IT WILL CRANK-START FOR 20 SECONDS AND ENGINE WILL STOP AGAIN. CAR STARTED WORKING …
Read full complaint
MY ML 320 YEAR 2000 MERCEDES-BENZ STOPPED SUDDENLY WHILE I WAS GOING 30 MILES AND HOUR. NO SIGN OF ANY PROBLEM (THAN ENGINE STALLED). THIS IS SCARY AND MUST BE INVESTIGATED. I ALMOST HIT A CAR. IT DID NOT START FOR 20 MINUTES AND THEN IT STARTED. IT WILL CRANK-START FOR 20 SECONDS AND ENGINE WILL STOP AGAIN. CAR STARTED WORKING FINE AFTER 45 MINUTES WAIT. *TR
NHTSA ODI #10419401
65,000 miles · Aug 26, 2008
Power Train
I HAVE A 2000 MERCEDES BENZ ML320 SUV. THIS VEHICLE SHIFTS AUTOMATICALLY FROM DRIVE TO FIRST GEAR WHEN GOING AT LAWFUL HIGH SPEED AND SOMETIMES LOW SPEEDS, DANGEROUSLY SLOWING THE VEHICLE PUTTING MY FAMILY'S LIVES AND OTHER DRIVERS IN PERIL ON THE ROAD. THE ABOVE INCIDENT OCCURRED EIGHT TIMES WITHIN THE LAST YEAR AND A HALF.…
Read full complaint
I HAVE A 2000 MERCEDES BENZ ML320 SUV. THIS VEHICLE SHIFTS AUTOMATICALLY FROM DRIVE TO FIRST GEAR WHEN GOING AT LAWFUL HIGH SPEED AND SOMETIMES LOW SPEEDS, DANGEROUSLY SLOWING THE VEHICLE PUTTING MY FAMILY'S LIVES AND OTHER DRIVERS IN PERIL ON THE ROAD. THE ABOVE INCIDENT OCCURRED EIGHT TIMES WITHIN THE LAST YEAR AND A HALF. THE MERCEDES BENZ DEALER COULD NOT FIND THE PROBLEM. *TR
NHTSA ODI #10239777
72,277 miles · Jul 28, 2006
Power Train
DT*: THE CONTACT STATED WHILE TRAVELING AT VARIOUS SPEEDS, THE VEHICLE STALLS AFTER BEING DRIVEN OVER A BUMP. AN INDEPENDENT REPAIR SHOP DETERMINED THE TRANSFER CASE SENSOR NEEDS TO BE REPLACED. UPDATED 8/14/2006 - *NM
NHTSA ODI #10163847
60,000 miles · Jun 7, 2006
Electrical SystemEngine And Engine CoolingEquipment
OIL CONSUMPTION PROBLEM. OIL LIGHT KEEPS COMING ON BETWEEN 200-600 MILES OF DRIVING. TRANSMISSION IS FAILING AND ENGINE NEEDS TO BE REPLACED. VERY POOR. *NM
NHTSA ODI #10159163
57,127 miles · Jun 20, 2005
Electrical SystemPower TrainSuspension
DT: CALLER HAS HAD VEHICLE IN 6 TIMES FOR CHECK ENGINE LIGHT/SPARK PLUGS BEING CORRODED/LOOSE WHEEL BEARING/CONTROL MODULE WENT OUT/FOR SHAKING AND SPUTTERING AT IDLE, AND THE ELECTRIC FUNCTION CHECK. MANUFACTURER HAS NOT BEEN CONTACTED YET. *AK
NHTSA ODI #10125793
31,000 miles · Mar 2, 2005
Air BagsEngine And Engine CoolingPower Train
THE CONSUMER'S MERCEDES BENZ M L 320 SLOWED DOWN ON ITS OWN. THE CONSUMER PULLED OVER PUT THE CAR IN PARK AND RESTARTED IT. *BF AFTER THIS INCIDENT THE CONSUMER PARKED IN A MALL PARKING LOT. WHEN SHE RETURNED TO THE VEHICLE THE SHIFT LEVER WOULD NOT MOVE OUT OF PARK. THE VEHICLE WAS TOWED TO A DEALER. AFTER THE VEHICLE WAS…
Read full complaint
THE CONSUMER'S MERCEDES BENZ M L 320 SLOWED DOWN ON ITS OWN. THE CONSUMER PULLED OVER PUT THE CAR IN PARK AND RESTARTED IT. *BF AFTER THIS INCIDENT THE CONSUMER PARKED IN A MALL PARKING LOT. WHEN SHE RETURNED TO THE VEHICLE THE SHIFT LEVER WOULD NOT MOVE OUT OF PARK. THE VEHICLE WAS TOWED TO A DEALER. AFTER THE VEHICLE WAS PICKED UP FROM THE DEALER IT WENT INTO STICK MODE AGAIN. THE SRS LIGHT ILLUMINATE ON THE DASH. THE VEHICLE WAS TAKEN TOT HE DEALER AND WHEN IT WAS RETURNED TO THE CONSUMER THE LIGHT WAS STILL ON. THE ENGINE LIGHT ILLUMINATED AND THE FRONT END VIBRATED. *NM
NHTSA ODI #10113591
94,000 miles · Feb 11, 2005
Power Train
WHILE DRIVING 65 MPH THE VEHICLE DECELERATED DOWN TO 10 MPH WITHOUT WARNING. THE CAUSE HAS YET TO BE DETERMINED. PLEASE PROVIDE ADDITIONAL INFORMATION.
NHTSA ODI #10111360
49,500 miles · Jul 15, 2003
Power Train
TRANSMISSION KEEPS GETTING STUCK IN 3RD GEAR. WHEN I TAKE IT TO BE SERVICED, THEY WOULD INITIALLY TELL ME NO COMPUTER ERRORS WERE SHOWING. A COUPLE TIMES LATER I DROVE TO THE DEALER WITH IT STUCK IN THIRD, ALLOWING THEM TO DRIVE IT THAT WAY. WHEN THIS OCCURRED I WAS IN THE LEFT LANE AND WAS UNABLE TO ACCELERATE CAUSING THE VE…
Read full complaint
TRANSMISSION KEEPS GETTING STUCK IN 3RD GEAR. WHEN I TAKE IT TO BE SERVICED, THEY WOULD INITIALLY TELL ME NO COMPUTER ERRORS WERE SHOWING. A COUPLE TIMES LATER I DROVE TO THE DEALER WITH IT STUCK IN THIRD, ALLOWING THEM TO DRIVE IT THAT WAY. WHEN THIS OCCURRED I WAS IN THE LEFT LANE AND WAS UNABLE TO ACCELERATE CAUSING THE VEHICLE BEHIND ME TO NEARLY REAR END US. THIS CONTINUES TO HAPPEN BUT VERY SPORADICALLY AND THE DEALER HAS UNSUCCESSFULLY BEEN ABLE TO REPAIR. THEIR RESPONSE NOW IS THEY ARE NOT ABLE TO DUPLICATE. THIS IS A SERIOUS PROBLEM.*AK
NHTSA ODI #10026132
Mileage unknown · Jun 24, 2003
Power Train
WHILE TRAVELING ON THE HIGHWAY VEHICLE WILL JERK WHILE IN GEAR. *AK
NHTSA ODI #10024856
40,503 miles · Jun 12, 2003
Power TrainCrashInjury
THE CAR WAS IN DRIVE, IT SUDDENLY WENT INTO REVERSE, ACCELERATED AT TREMENDOUS SPEED DOWN MY DRIVEWAY, UP ONTO MY PROPERTY WHERE IT HIT A TREE - STILL IN DRIVE. DAMAGE WAS IN ACCESS OF $16,000. MERCEDES DENIED ANY DEFECT OR MALFUNCTION AFTER THEIR INSPECTION. I HAVE SINCE LEARNED THAT AN ALMOST IDENTICAL ACCIDENT WAS REPORTED …
Read full complaint
THE CAR WAS IN DRIVE, IT SUDDENLY WENT INTO REVERSE, ACCELERATED AT TREMENDOUS SPEED DOWN MY DRIVEWAY, UP ONTO MY PROPERTY WHERE IT HIT A TREE - STILL IN DRIVE. DAMAGE WAS IN ACCESS OF $16,000. MERCEDES DENIED ANY DEFECT OR MALFUNCTION AFTER THEIR INSPECTION. I HAVE SINCE LEARNED THAT AN ALMOST IDENTICAL ACCIDENT WAS REPORTED IN 2000 TO ANOTHER CAR - SAME YEAR, MAKE & MODEL AS MINE. *NLM
NHTSA ODI #10021455
Official recalls
0
No recalls in this snapshot.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4
PE10050 · Brake Lamp Switch Failure.
Opened Dec 21, 2010 · Closed May 4, 2011
Status: closed (inferred from source dates) · Exterior Lighting:brake Lights:switch; Service Brakes, Hydraulic; Vehicle Speed Control; Vehicle Speed Control:cruise Control
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed
Additional source detail variants (4)
Exterior Lighting:brake Lights:switch
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed
Service Brakes, Hydraulic
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed
Vehicle Speed Control:cruise Control
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed
Vehicle Speed Control
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed
PE07007 · Electronic Stability Control Malfunction
ODI OPENED PE07-007 AFTER RECEIVING 4 COMPLAINTS WITHIN A 6 WEEK PERIOD ALLEGING INCIDENTS OF UNCOMMANDED BRAKE APPLICATION IN MODEL YEAR (MY) 2000 THROUGH 2001 MERCEDES M CLASS SPORT UTILITY VEHICLES.INFORMATION CONTAINED IN THE REPORTS OR GATHERED IN SUBSEQUENT CONSUMER INTERVIEWS INDICATED THAT THE INCIDENTS WERE CAUSED BY FAULTS IN THE ELECTRONIC STABILITY PROGRAM (ESP) SYSTEM WHICH WERE REPAIRED BY REPLACING THE YAW RATE SENSORS.ALTHOUGH THE SAME YAW RATE SENSOR IS USED IN APPROXIMATELY 800,000 OTHER MERCEDES M-CLASS, C-CLASS AND SLK MODELS, TO DATE THERE HAS BEEN ONLY ONE RELATED COMPLAINT TO ODI IN THOSE VEHICLES. DURING THIS INVESTIGATION MERCEDES BENZ PROVIDED ODI WITH 327 COMPLAINTS RELATED TO THE ESP SYSTEM IN THE MY 2000 THROUGH 2001 M CLASS VEHICLES.SEVEN OF THE COMPLAINTS SUBMITTED BY MERCEDES ALLEGED INCIDENTS OF UNCOMMANDED BRAKE ACTIVATION WHILE DRIVING, WITH TWO OF THESE INVOLVING VEHICLES IDENTIFIED IN THE ODI COMPLAINTS.NONE OF THE INCIDENTS RESULTED IN CRASH OR INJURY.HOWEVER, THE OWNERS DID EXPRESS SAFETY CONCERNS DUE TO THE SUDDEN, UNEXPECTED CHANGE IN VEHICLE SPEED AND DIRECTION. ON MAY 10, 2007 MERCEDES BENZ MET WITH NHTSA TO PROVIDE A TECHNICAL PRESENTATION AND CONDUCT A DRIVING DEMONSTRATION OF THE ESP SYSTEM PERFORMANCE WITH SIMULATED ELECTRICAL FAULTS IN THE YAW RATE SENSOR.MERCEDES SHOWED THAT THE ESP SYSTEM IS PROGRAMMED TO DIAGNOSE ELECTRICAL FAULTS AND THAT BRAKE APPLICATIONS RESULTING FROM YAW RATE SENSOR ELECTRICAL FAULTS ARE VERY SHORT IN DURATION (0.3 SECONDS OR LESS) AND DO NOT AFFECT VEHICLE CONTROL OR STABILITY. NINE OF THE CONSUMER COMPLAINTS TO ODI AND MERCEDES ALLEGED BRAKE ACTIVATIONS LONGER THAN 0.3 SECONDS, WITH SEVERAL ALLEGING THAT THE INCIDENT LASTED UNTIL THE VEHICLE CAME TO A STOP.A COMPLAINT VEHICLE THAT ALLEGED MULTIPLE INCIDENTS WAS EVALUATED BY ODI AT THE VEHICLE RESEARCH AND TEST CENTER (VRTC) IN EAST LIBERTY, OHIO.VRTC WAS UNABLE TO DUPLICATE THE CONDITION.DUE TO THE LOW COMPLAINT RATE AND ONLY ONE NEW COMPLAINT TO ODI OR MERCEDES SINCE JANUARY 2007, THIS INVESTIGATION HAS BEEN CLOSED.ODI WILL CONTINUE TO MONITOR COMPLAINTS IN THE SUBJECT VEHICLES AND OTHER MERCEDES PRODUCTS USING THE SAME YAW RATE SENSOR AND MERCEDES WILL PROVIDE UPDATES ON FIELD EXPERIENCE (COMPLAINTS, FIELD REPORTS AND WARRANTY CLAIMS) THROUGH THE END OF 2007.
PE03058 · Engine Crankshaft Pulley Failure
Opened Dec 17, 2003 · Closed Apr 22, 2004
Status: closed (inferred from source dates) · Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
THE OFFICE OF DEFECTS INVESTIGATION (ODI) OPENED THIS PRELIMINARY EVALUATION TO INVESTIGATE ALLEGATIONS OF ENGINE CRANKSHAFT PULLEY HARMONIC BALANCER FAILURE THAT COULD RESULT IN LOSS OF POWER-STEERING ASSIST.ODI HAS RECEIVED A TOTAL OF 546 NON-DUPLICATIVE REPORTS THAT ALLEGE ENGINE CRANKSHAFT PULLEY HARMONIC BALANCER FAILURE ON ALL MERCEDES-BENZ VEHICLES USING THE SUBJECT COMPONENT.THE SUBJECT COMPONENT FAILURES ARE PROGRESSIVE IN NATURE AND ONLY A SMALL PERCENTAGE OF THE COMPLAINTS AND WARRANT CLAIMS INVOLVED A FAILURE THAT HAD PROGRESSED FAR ENOUGH TO EFFECT POWER STEERING PERFORMANCE (6 OF 55 ODI COMPLAINTS REFERENCE INCREASED STEERING EFFORT).THERE HAVE BEEN NO CRASHES OR INJURIES RELATED TO THE ALLEGED DEFECT.A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.SEE SUMMARY REPORT ATTACHED FOR FURTHER DETAIL.
PE03006 · Power Steering Hose Assembly Leakage
Opened Feb 13, 2003 · Closed Apr 4, 2003
Status: closed (inferred from source dates) · Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid
THE HOSE CLAMP USED TO SECURE THE POWER STEERING FLUID COOLING HOSE TO THE STEERING FLUID COOLER MAY NOT PROVIDE SUFFICIENT CLAMPING FORCE FOR THE CONNECTION.THE LOSS OF POWER STEERING FLUID MAY RESULT IN GRADUAL REDUCTION IN POWER STEERING ASSIST (I.E., INCREASED STEERING EFFORT) OVER TIME, WITH POTENTIAL DAMAGE TO THE POWER STEERING PUMP. THERE HAVE ALSO BEEN A FEW INCIDENTS OF HOSE SEPARATION FROM THE FITTING, THAT HAVE RESULTED IN MORE RAPID REDUCTIONS OF POWER STEERING.TESTING CONDUCTED BY MERCEDES-BENZ INDICATES THAT THE LEAKED FLUID IS NOT LIKELY TO BE EXPOSED TO HOT ENGINE COMPONENTS.THERE ARE NO KNOWN ALLEGATIONS THAT THE DEFECT CONDITION HAS CAUSED A VEHICLE FIRE. MERCEDES-BENZ WILL CONDUCT A VOLUNTARY RECALL CAMPAIGN FOR THE SUBJECT M-CLASS VEHICLES.MERCEDES-BENZ WILL INSTALL A NEW HOSE CLAMP ON THE POWER STEERING HOSE TO THE POWER STEERING COOLER OF THE SUBJECT VEHICLES.DURING CLAMP REPLACEMENT, THE POWER STEERING COOLING HOSE WILL BE INSPECTED AND REPLACED AS NECESSARY.
Additional source detail variants (2)
Steering:hydraulic Power Assist:hose, Piping, And Connections
THE HOSE CLAMP USED TO SECURE THE POWER STEERING FLUID COOLING HOSE TO THE STEERING FLUID COOLER MAY NOT PROVIDE SUFFICIENT CLAMPING FORCE FOR THE CONNECTION.THE LOSS OF POWER STEERING FLUID MAY RESULT IN GRADUAL REDUCTION IN POWER STEERING ASSIST (I.E., INCREASED STEERING EFFORT) OVER TIME, WITH POTENTIAL DAMAGE TO THE POWER STEERING PUMP. THERE HAVE ALSO BEEN A FEW INCIDENTS OF HOSE SEPARATION FROM THE FITTING, THAT HAVE RESULTED IN MORE RAPID REDUCTIONS OF POWER STEERING.TESTING CONDUCTED BY MERCEDES-BENZ INDICATES THAT THE LEAKED FLUID IS NOT LIKELY TO BE EXPOSED TO HOT ENGINE COMPONENTS.THERE ARE NO KNOWN ALLEGATIONS THAT THE DEFECT CONDITION HAS CAUSED A VEHICLE FIRE. MERCEDES-BENZ WILL CONDUCT A VOLUNTARY RECALL CAMPAIGN FOR THE SUBJECT M-CLASS VEHICLES.MERCEDES-BENZ WILL INSTALL A NEW HOSE CLAMP ON THE POWER STEERING HOSE TO THE POWER STEERING COOLER OF THE SUBJECT VEHICLES.DURING CLAMP REPLACEMENT, THE POWER STEERING COOLING HOSE WILL BE INSPECTED AND REPLACED AS NECESSARY.
Steering:hydraulic Power Assist:power Steering Fluid
THE HOSE CLAMP USED TO SECURE THE POWER STEERING FLUID COOLING HOSE TO THE STEERING FLUID COOLER MAY NOT PROVIDE SUFFICIENT CLAMPING FORCE FOR THE CONNECTION.THE LOSS OF POWER STEERING FLUID MAY RESULT IN GRADUAL REDUCTION IN POWER STEERING ASSIST (I.E., INCREASED STEERING EFFORT) OVER TIME, WITH POTENTIAL DAMAGE TO THE POWER STEERING PUMP. THERE HAVE ALSO BEEN A FEW INCIDENTS OF HOSE SEPARATION FROM THE FITTING, THAT HAVE RESULTED IN MORE RAPID REDUCTIONS OF POWER STEERING.TESTING CONDUCTED BY MERCEDES-BENZ INDICATES THAT THE LEAKED FLUID IS NOT LIKELY TO BE EXPOSED TO HOT ENGINE COMPONENTS.THERE ARE NO KNOWN ALLEGATIONS THAT THE DEFECT CONDITION HAS CAUSED A VEHICLE FIRE. MERCEDES-BENZ WILL CONDUCT A VOLUNTARY RECALL CAMPAIGN FOR THE SUBJECT M-CLASS VEHICLES.MERCEDES-BENZ WILL INSTALL A NEW HOSE CLAMP ON THE POWER STEERING HOSE TO THE POWER STEERING COOLER OF THE SUBJECT VEHICLES.DURING CLAMP REPLACEMENT, THE POWER STEERING COOLING HOSE WILL BE INSPECTED AND REPLACED AS NECESSARY.
2000 Mercedes Benz ML320 Problems, Complaints & Recalls | Skip That Year
Illustration