IllustrationAT 43,500 AND 54 MONTHS THE TRANSMISSION IN THE CAR HAD TO BE REPLACED. THE CAR HAS ALWAYS BEEN PROPERLY SERVICED AT THE MERCEDES DEALER. I BELIEVE THIS MODEL/MAKE HAS DEFECTS AS I HAVE BROUGHT IT BACK FOR SERVICE MANY TIMES. *TR
2009 Mercedes Benz C
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all C years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 13 of 14 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Exterior Lighting. Review the 4 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 4 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 3 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
2 crash reports0 fire reports2 injury reports
Power Train complaints
4 reportsTL*THE CONTACT OWNS A 2009 MERCEDES C350. THE CONTACT STATED THAT WHEN THE ACCELERATOR PEDAL WAS ENGAGED, THE TRANSMISSION SURGED FORWARD AT A HIGH RATE. THE FAILURE OCCURRED INTERMITTENTLY. THE DEALER WAS UNABLE TO DUPLICATE OR DIAGNOSE THE FAILURE. THE FAILURE MILEAGE WAS 15 AND THE CURRENT MILEAGE WAS 32000.
TL*THE CONTACT OWNS A 2009 MERCEDES BENZ C300. WHENEVER THE CONTACT PLACED THE VEHICLE INTO REVERSE OR DRIVE I WOULD VIOLENTLY SWITCH INTO GEAR CAUSING THE VEHICLE TO SLIGHTLY SURGE FORWARD. THE VEHICLE HAS BEEN TAKEN TO THE DEALERSHIP ON THIRTEEN DIFFERENT OCCASIONS WHERE SEVERAL DIFFERENT PARTS HAVE BEEN SERVICED ON THE TRANSM…
Read full complaint
TL*THE CONTACT OWNS A 2009 MERCEDES BENZ C300. WHENEVER THE CONTACT PLACED THE VEHICLE INTO REVERSE OR DRIVE I WOULD VIOLENTLY SWITCH INTO GEAR CAUSING THE VEHICLE TO SLIGHTLY SURGE FORWARD. THE VEHICLE HAS BEEN TAKEN TO THE DEALERSHIP ON THIRTEEN DIFFERENT OCCASIONS WHERE SEVERAL DIFFERENT PARTS HAVE BEEN SERVICED ON THE TRANSMISSION;HOWEVER THE CONTACT IS STILL EXPERIENCING THE FAILURE. THE CONTACT HAS NOTICED THE FAILURE SINCE THE VEHICLE WAS PURCHASED. THE CURRENT AND FAILURE MILEAGES WERE 14000.
TL*THE CONTACT OWNS A 2009 MERCEDES BENZ C300. THE CONTACT STATED THAT THE VEHICLE WAS EXPERIENCING SEVERAL COMPUTER DEFECTS. WHILE PARKED ON A HILL AND ATTEMPTING TO PLACE THE GEAR SHIFTER INTO REVERSE, THE VEHICLE WOULD ROLL FORWARD INSTEAD OF BACKWARDS. THE VEHICLE WOULD ROLL FORWARD APPROXIMATELY ONE FOOT AS IF IT WERE IN…
Read full complaint
TL*THE CONTACT OWNS A 2009 MERCEDES BENZ C300. THE CONTACT STATED THAT THE VEHICLE WAS EXPERIENCING SEVERAL COMPUTER DEFECTS. WHILE PARKED ON A HILL AND ATTEMPTING TO PLACE THE GEAR SHIFTER INTO REVERSE, THE VEHICLE WOULD ROLL FORWARD INSTEAD OF BACKWARDS. THE VEHICLE WOULD ROLL FORWARD APPROXIMATELY ONE FOOT AS IF IT WERE IN NEUTRAL. DURING THIS TIME, THE STEERING WOULD LOCK AND THE BRAKES WOULD LOSE POWER. IT WOULD TAKE TREMENDOUS FORCE TO DEPRESS THE BRAKE PEDAL AND STOP THE VEHICLE. THE DEALER AND MANUFACTURER COULD NOT ASSIST WITH THE REPAIRS. THERE WERE NO RECALLS AVAILABLE. THE DEALER COULD NOT DETERMINE THE CAUSE OF THE FAILURE. NO REPAIRS HAVE BEEN PERFORMED. THE VIN WAS UNKNOWN. THE FAILURE AND CURRENT MILEAGES WERE LESS THAN 7,000.
Official recalls
0No recalls in this snapshot.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA13008 · Loss Of Rear Lighting Assembly
Opened Dec 20, 2013 · Closed May 12, 2014
Status: closed (inferred from source dates) · Electrical System:wiring; Electrical System:wiring: Rear Compartment/trunk; Exterior Lighting; Exterior Lighting:back Up Lights; Exterior Lighting:brake Lights; Exterior Lighting:fog Lights; Exterior Lighting:hazard Flashing Warning Lights; Exterior Lighting:tail Lights; Exterior Lighting:turn Signal
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) or illuminate dimly.In some reports, complainants also alleged that the failure was accompanied by a burning smell emanating from the trunk of the vehicle.When examined, these vehicles showed evidence of overheating at the lighting assembly harness connector, including damaged (blackened) wiring and plastic.The rear lighting failures typically involved one side of the vehicle however in some cases both assemblies failed (although probably not simultaneously).ODI identified 5 fire and one injury allegations during the course of this investigation.Two fires occurred while the vehicles were parked.One originated in the vicinity of the driver?s side light assembly where the fire and associated damage was confined to the trunk area, and the fire self extinguished due to oxygen starvation.As a result of the fire, the vehicle was repurchased by Mercedes and salvaged.The second fire originated on the passenger's side and required fire department response to extinguish; the fire damaged the tail light and surrounding body panels as well as the trunk area and wiring.The vehicle was repaired and returned to service.Two firesoccurred while the vehicle was being driven.In the first instance, the driver detected an odor and pulled over to observe smoking and a small flame at the lighting assembly wiring in the trunk.The owner was able to extinguish the fire before any significant damage occurred.In the second instance, the driver smelled smoke, pulled over, and opened the trunk to find smoke and sparks emanating from the forward facing side of the tail light.The driver was able to extinguish the sparks and drive the vehicle to the dealer. A fifth fire was reported by a fleet manager who observed a vehicle with fire damage originating near one of the tail light assemblies.The injury incident occurred when a technician burned their hand while diagnosing a failed light.The technician touched the tail light wiring which was hot enough to burn him although the injury did not require medical attention.On April 10th, 2014, Mercedes notified ODI that it would conduct a safety recall to remedy the rear light assemblies in approximately 252,867 MY 2008 - 2011 C-Class vehicles including the C300, C350 and C63 AMG models.Each rear light assembly has separate bulbs that act as brake, tail lamp, backup and turn signal indicators.The bulbs are mounted in a bulb carrier which uses a common electrical ground circuit at the harness connection.According to Mercedes, oxidation due to the use of dissimilar metals on the harness and bulb carrier electrical connectors can result in increased resistance and a subsequent dimming or loss of lighting function.The heat caused by the increased resistance/oxidation can also lead to the melting of the surrounding plastic, or in some cases, present a fire hazard.In conducting recall 14V-171, Mercedes dealers will inspect the left and right bulb carriers and harness connectors for the presence of dissimilar electrical connectors and/or evidence of related thermal damage; affected bulb carriers and/or harness connectors will be replaced free of charge.Mercedes notes that service replacement bulb carriers produced from January 2012 eliminate the dissimilar metal condition and that these bulb carriers will not requ
Additional source detail variants (9)
Electrical System:wiring
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) or illuminate dimly.In some reports, complainants also alleged that the failure was accompanied by a burning smell emanating from the trunk of the vehicle.When examined, these vehicles showed evidence of overheating at the lighting assembly harness connector, including damaged (blackened) wiring and plastic.The rear lighting failures typically involved one side of the vehicle however in some cases both assemblies failed (although probably not simultaneously).ODI identified 5 fire and one injury allegations during the course of this investigation.Two fires occurred while the vehicles were parked.One originated in the vicinity of the driver?s side light assembly where the fire and associated damage was confined to the trunk area, and the fire self extinguished due to oxygen starvation.As a result of the fire, the vehicle was repurchased by Mercedes and salvaged.The second fire originated on the passenger's side and required fire department response to extinguish; the fire damaged the tail light and surrounding body panels as well as the trunk area and wiring.The vehicle was repaired and returned to service.Two firesoccurred while the vehicle was being driven.In the first instance, the driver detected an odor and pulled over to observe smoking and a small flame at the lighting assembly wiring in the trunk.The owner was able to extinguish the fire before any significant damage occurred.In the second instance, the driver smelled smoke, pulled over, and opened the trunk to find smoke and sparks emanating from the forward facing side of the tail light.The driver was able to extinguish the sparks and drive the vehicle to the dealer. A fifth fire was reported by a fleet manager who observed a vehicle with fire damage originating near one of the tail light assemblies.The injury incident occurred when a technician burned their hand while diagnosing a failed light.The technician touched the tail light wiring which was hot enough to burn him although the injury did not require medical attention.On April 10th, 2014, Mercedes notified ODI that it would conduct a safety recall to remedy the rear light assemblies in approximately 252,867 MY 2008 - 2011 C-Class vehicles including the C300, C350 and C63 AMG models.Each rear light assembly has separate bulbs that act as brake, tail lamp, backup and turn signal indicators.The bulbs are mounted in a bulb carrier which uses a common electrical ground circuit at the harness connection.According to Mercedes, oxidation due to the use of dissimilar metals on the harness and bulb carrier electrical connectors can result in increased resistance and a subsequent dimming or loss of lighting function.The heat caused by the increased resistance/oxidation can also lead to the melting of the surrounding plastic, or in some cases, present a fire hazard.In conducting recall 14V-171, Mercedes dealers will inspect the left and right bulb carriers and harness connectors for the presence of dissimilar electrical connectors and/or evidence of related thermal damage; affected bulb carriers and/or harness connectors will be replaced free of charge.Mercedes notes that service replacement bulb carriers produced from January 2012 eliminate the dissimilar metal condition and that these bulb carriers will not requ
Electrical System:wiring: Rear Compartment/trunk
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) or illuminate dimly.In some reports, complainants also alleged that the failure was accompanied by a burning smell emanating from the trunk of the vehicle.When examined, these vehicles showed evidence of overheating at the lighting assembly harness connector, including damaged (blackened) wiring and plastic.The rear lighting failures typically involved one side of the vehicle however in some cases both assemblies failed (although probably not simultaneously).ODI identified 5 fire and one injury allegations during the course of this investigation.Two fires occurred while the vehicles were parked.One originated in the vicinity of the driver?s side light assembly where the fire and associated damage was confined to the trunk area, and the fire self extinguished due to oxygen starvation.As a result of the fire, the vehicle was repurchased by Mercedes and salvaged.The second fire originated on the passenger's side and required fire department response to extinguish; the fire damaged the tail light and surrounding body panels as well as the trunk area and wiring.The vehicle was repaired and returned to service.Two firesoccurred while the vehicle was being driven.In the first instance, the driver detected an odor and pulled over to observe smoking and a small flame at the lighting assembly wiring in the trunk.The owner was able to extinguish the fire before any significant damage occurred.In the second instance, the driver smelled smoke, pulled over, and opened the trunk to find smoke and sparks emanating from the forward facing side of the tail light.The driver was able to extinguish the sparks and drive the vehicle to the dealer. A fifth fire was reported by a fleet manager who observed a vehicle with fire damage originating near one of the tail light assemblies.The injury incident occurred when a technician burned their hand while diagnosing a failed light.The technician touched the tail light wiring which was hot enough to burn him although the injury did not require medical attention.On April 10th, 2014, Mercedes notified ODI that it would conduct a safety recall to remedy the rear light assemblies in approximately 252,867 MY 2008 - 2011 C-Class vehicles including the C300, C350 and C63 AMG models.Each rear light assembly has separate bulbs that act as brake, tail lamp, backup and turn signal indicators.The bulbs are mounted in a bulb carrier which uses a common electrical ground circuit at the harness connection.According to Mercedes, oxidation due to the use of dissimilar metals on the harness and bulb carrier electrical connectors can result in increased resistance and a subsequent dimming or loss of lighting function.The heat caused by the increased resistance/oxidation can also lead to the melting of the surrounding plastic, or in some cases, present a fire hazard.In conducting recall 14V-171, Mercedes dealers will inspect the left and right bulb carriers and harness connectors for the presence of dissimilar electrical connectors and/or evidence of related thermal damage; affected bulb carriers and/or harness connectors will be replaced free of charge.Mercedes notes that service replacement bulb carriers produced from January 2012 eliminate the dissimilar metal condition and that these bulb carriers will not requ
Exterior Lighting:back Up Lights
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) or illuminate dimly.In some reports, complainants also alleged that the failure was accompanied by a burning smell emanating from the trunk of the vehicle.When examined, these vehicles showed evidence of overheating at the lighting assembly harness connector, including damaged (blackened) wiring and plastic.The rear lighting failures typically involved one side of the vehicle however in some cases both assemblies failed (although probably not simultaneously).ODI identified 5 fire and one injury allegations during the course of this investigation.Two fires occurred while the vehicles were parked.One originated in the vicinity of the driver?s side light assembly where the fire and associated damage was confined to the trunk area, and the fire self extinguished due to oxygen starvation.As a result of the fire, the vehicle was repurchased by Mercedes and salvaged.The second fire originated on the passenger's side and required fire department response to extinguish; the fire damaged the tail light and surrounding body panels as well as the trunk area and wiring.The vehicle was repaired and returned to service.Two firesoccurred while the vehicle was being driven.In the first instance, the driver detected an odor and pulled over to observe smoking and a small flame at the lighting assembly wiring in the trunk.The owner was able to extinguish the fire before any significant damage occurred.In the second instance, the driver smelled smoke, pulled over, and opened the trunk to find smoke and sparks emanating from the forward facing side of the tail light.The driver was able to extinguish the sparks and drive the vehicle to the dealer. A fifth fire was reported by a fleet manager who observed a vehicle with fire damage originating near one of the tail light assemblies.The injury incident occurred when a technician burned their hand while diagnosing a failed light.The technician touched the tail light wiring which was hot enough to burn him although the injury did not require medical attention.On April 10th, 2014, Mercedes notified ODI that it would conduct a safety recall to remedy the rear light assemblies in approximately 252,867 MY 2008 - 2011 C-Class vehicles including the C300, C350 and C63 AMG models.Each rear light assembly has separate bulbs that act as brake, tail lamp, backup and turn signal indicators.The bulbs are mounted in a bulb carrier which uses a common electrical ground circuit at the harness connection.According to Mercedes, oxidation due to the use of dissimilar metals on the harness and bulb carrier electrical connectors can result in increased resistance and a subsequent dimming or loss of lighting function.The heat caused by the increased resistance/oxidation can also lead to the melting of the surrounding plastic, or in some cases, present a fire hazard.In conducting recall 14V-171, Mercedes dealers will inspect the left and right bulb carriers and harness connectors for the presence of dissimilar electrical connectors and/or evidence of related thermal damage; affected bulb carriers and/or harness connectors will be replaced free of charge.Mercedes notes that service replacement bulb carriers produced from January 2012 eliminate the dissimilar metal condition and that these bulb carriers will not requ
Exterior Lighting:brake Lights
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) or illuminate dimly.In some reports, complainants also alleged that the failure was accompanied by a burning smell emanating from the trunk of the vehicle.When examined, these vehicles showed evidence of overheating at the lighting assembly harness connector, including damaged (blackened) wiring and plastic.The rear lighting failures typically involved one side of the vehicle however in some cases both assemblies failed (although probably not simultaneously).ODI identified 5 fire and one injury allegations during the course of this investigation.Two fires occurred while the vehicles were parked.One originated in the vicinity of the driver?s side light assembly where the fire and associated damage was confined to the trunk area, and the fire self extinguished due to oxygen starvation.As a result of the fire, the vehicle was repurchased by Mercedes and salvaged.The second fire originated on the passenger's side and required fire department response to extinguish; the fire damaged the tail light and surrounding body panels as well as the trunk area and wiring.The vehicle was repaired and returned to service.Two firesoccurred while the vehicle was being driven.In the first instance, the driver detected an odor and pulled over to observe smoking and a small flame at the lighting assembly wiring in the trunk.The owner was able to extinguish the fire before any significant damage occurred.In the second instance, the driver smelled smoke, pulled over, and opened the trunk to find smoke and sparks emanating from the forward facing side of the tail light.The driver was able to extinguish the sparks and drive the vehicle to the dealer. A fifth fire was reported by a fleet manager who observed a vehicle with fire damage originating near one of the tail light assemblies.The injury incident occurred when a technician burned their hand while diagnosing a failed light.The technician touched the tail light wiring which was hot enough to burn him although the injury did not require medical attention.On April 10th, 2014, Mercedes notified ODI that it would conduct a safety recall to remedy the rear light assemblies in approximately 252,867 MY 2008 - 2011 C-Class vehicles including the C300, C350 and C63 AMG models.Each rear light assembly has separate bulbs that act as brake, tail lamp, backup and turn signal indicators.The bulbs are mounted in a bulb carrier which uses a common electrical ground circuit at the harness connection.According to Mercedes, oxidation due to the use of dissimilar metals on the harness and bulb carrier electrical connectors can result in increased resistance and a subsequent dimming or loss of lighting function.The heat caused by the increased resistance/oxidation can also lead to the melting of the surrounding plastic, or in some cases, present a fire hazard.In conducting recall 14V-171, Mercedes dealers will inspect the left and right bulb carriers and harness connectors for the presence of dissimilar electrical connectors and/or evidence of related thermal damage; affected bulb carriers and/or harness connectors will be replaced free of charge.Mercedes notes that service replacement bulb carriers produced from January 2012 eliminate the dissimilar metal condition and that these bulb carriers will not requ
Exterior Lighting:fog Lights
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) or illuminate dimly.In some reports, complainants also alleged that the failure was accompanied by a burning smell emanating from the trunk of the vehicle.When examined, these vehicles showed evidence of overheating at the lighting assembly harness connector, including damaged (blackened) wiring and plastic.The rear lighting failures typically involved one side of the vehicle however in some cases both assemblies failed (although probably not simultaneously).ODI identified 5 fire and one injury allegations during the course of this investigation.Two fires occurred while the vehicles were parked.One originated in the vicinity of the driver?s side light assembly where the fire and associated damage was confined to the trunk area, and the fire self extinguished due to oxygen starvation.As a result of the fire, the vehicle was repurchased by Mercedes and salvaged.The second fire originated on the passenger's side and required fire department response to extinguish; the fire damaged the tail light and surrounding body panels as well as the trunk area and wiring.The vehicle was repaired and returned to service.Two firesoccurred while the vehicle was being driven.In the first instance, the driver detected an odor and pulled over to observe smoking and a small flame at the lighting assembly wiring in the trunk.The owner was able to extinguish the fire before any significant damage occurred.In the second instance, the driver smelled smoke, pulled over, and opened the trunk to find smoke and sparks emanating from the forward facing side of the tail light.The driver was able to extinguish the sparks and drive the vehicle to the dealer. A fifth fire was reported by a fleet manager who observed a vehicle with fire damage originating near one of the tail light assemblies.The injury incident occurred when a technician burned their hand while diagnosing a failed light.The technician touched the tail light wiring which was hot enough to burn him although the injury did not require medical attention.On April 10th, 2014, Mercedes notified ODI that it would conduct a safety recall to remedy the rear light assemblies in approximately 252,867 MY 2008 - 2011 C-Class vehicles including the C300, C350 and C63 AMG models.Each rear light assembly has separate bulbs that act as brake, tail lamp, backup and turn signal indicators.The bulbs are mounted in a bulb carrier which uses a common electrical ground circuit at the harness connection.According to Mercedes, oxidation due to the use of dissimilar metals on the harness and bulb carrier electrical connectors can result in increased resistance and a subsequent dimming or loss of lighting function.The heat caused by the increased resistance/oxidation can also lead to the melting of the surrounding plastic, or in some cases, present a fire hazard.In conducting recall 14V-171, Mercedes dealers will inspect the left and right bulb carriers and harness connectors for the presence of dissimilar electrical connectors and/or evidence of related thermal damage; affected bulb carriers and/or harness connectors will be replaced free of charge.Mercedes notes that service replacement bulb carriers produced from January 2012 eliminate the dissimilar metal condition and that these bulb carriers will not requ
Exterior Lighting:hazard Flashing Warning Lights
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) or illuminate dimly.In some reports, complainants also alleged that the failure was accompanied by a burning smell emanating from the trunk of the vehicle.When examined, these vehicles showed evidence of overheating at the lighting assembly harness connector, including damaged (blackened) wiring and plastic.The rear lighting failures typically involved one side of the vehicle however in some cases both assemblies failed (although probably not simultaneously).ODI identified 5 fire and one injury allegations during the course of this investigation.Two fires occurred while the vehicles were parked.One originated in the vicinity of the driver?s side light assembly where the fire and associated damage was confined to the trunk area, and the fire self extinguished due to oxygen starvation.As a result of the fire, the vehicle was repurchased by Mercedes and salvaged.The second fire originated on the passenger's side and required fire department response to extinguish; the fire damaged the tail light and surrounding body panels as well as the trunk area and wiring.The vehicle was repaired and returned to service.Two firesoccurred while the vehicle was being driven.In the first instance, the driver detected an odor and pulled over to observe smoking and a small flame at the lighting assembly wiring in the trunk.The owner was able to extinguish the fire before any significant damage occurred.In the second instance, the driver smelled smoke, pulled over, and opened the trunk to find smoke and sparks emanating from the forward facing side of the tail light.The driver was able to extinguish the sparks and drive the vehicle to the dealer. A fifth fire was reported by a fleet manager who observed a vehicle with fire damage originating near one of the tail light assemblies.The injury incident occurred when a technician burned their hand while diagnosing a failed light.The technician touched the tail light wiring which was hot enough to burn him although the injury did not require medical attention.On April 10th, 2014, Mercedes notified ODI that it would conduct a safety recall to remedy the rear light assemblies in approximately 252,867 MY 2008 - 2011 C-Class vehicles including the C300, C350 and C63 AMG models.Each rear light assembly has separate bulbs that act as brake, tail lamp, backup and turn signal indicators.The bulbs are mounted in a bulb carrier which uses a common electrical ground circuit at the harness connection.According to Mercedes, oxidation due to the use of dissimilar metals on the harness and bulb carrier electrical connectors can result in increased resistance and a subsequent dimming or loss of lighting function.The heat caused by the increased resistance/oxidation can also lead to the melting of the surrounding plastic, or in some cases, present a fire hazard.In conducting recall 14V-171, Mercedes dealers will inspect the left and right bulb carriers and harness connectors for the presence of dissimilar electrical connectors and/or evidence of related thermal damage; affected bulb carriers and/or harness connectors will be replaced free of charge.Mercedes notes that service replacement bulb carriers produced from January 2012 eliminate the dissimilar metal condition and that these bulb carriers will not requ
Exterior Lighting
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) or illuminate dimly.In some reports, complainants also alleged that the failure was accompanied by a burning smell emanating from the trunk of the vehicle.When examined, these vehicles showed evidence of overheating at the lighting assembly harness connector, including damaged (blackened) wiring and plastic.The rear lighting failures typically involved one side of the vehicle however in some cases both assemblies failed (although probably not simultaneously).ODI identified 5 fire and one injury allegations during the course of this investigation.Two fires occurred while the vehicles were parked.One originated in the vicinity of the driver?s side light assembly where the fire and associated damage was confined to the trunk area, and the fire self extinguished due to oxygen starvation.As a result of the fire, the vehicle was repurchased by Mercedes and salvaged.The second fire originated on the passenger's side and required fire department response to extinguish; the fire damaged the tail light and surrounding body panels as well as the trunk area and wiring.The vehicle was repaired and returned to service.Two firesoccurred while the vehicle was being driven.In the first instance, the driver detected an odor and pulled over to observe smoking and a small flame at the lighting assembly wiring in the trunk.The owner was able to extinguish the fire before any significant damage occurred.In the second instance, the driver smelled smoke, pulled over, and opened the trunk to find smoke and sparks emanating from the forward facing side of the tail light.The driver was able to extinguish the sparks and drive the vehicle to the dealer. A fifth fire was reported by a fleet manager who observed a vehicle with fire damage originating near one of the tail light assemblies.The injury incident occurred when a technician burned their hand while diagnosing a failed light.The technician touched the tail light wiring which was hot enough to burn him although the injury did not require medical attention.On April 10th, 2014, Mercedes notified ODI that it would conduct a safety recall to remedy the rear light assemblies in approximately 252,867 MY 2008 - 2011 C-Class vehicles including the C300, C350 and C63 AMG models.Each rear light assembly has separate bulbs that act as brake, tail lamp, backup and turn signal indicators.The bulbs are mounted in a bulb carrier which uses a common electrical ground circuit at the harness connection.According to Mercedes, oxidation due to the use of dissimilar metals on the harness and bulb carrier electrical connectors can result in increased resistance and a subsequent dimming or loss of lighting function.The heat caused by the increased resistance/oxidation can also lead to the melting of the surrounding plastic, or in some cases, present a fire hazard.In conducting recall 14V-171, Mercedes dealers will inspect the left and right bulb carriers and harness connectors for the presence of dissimilar electrical connectors and/or evidence of related thermal damage; affected bulb carriers and/or harness connectors will be replaced free of charge.Mercedes notes that service replacement bulb carriers produced from January 2012 eliminate the dissimilar metal condition and that these bulb carriers will not requ
Exterior Lighting:tail Lights
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) or illuminate dimly.In some reports, complainants also alleged that the failure was accompanied by a burning smell emanating from the trunk of the vehicle.When examined, these vehicles showed evidence of overheating at the lighting assembly harness connector, including damaged (blackened) wiring and plastic.The rear lighting failures typically involved one side of the vehicle however in some cases both assemblies failed (although probably not simultaneously).ODI identified 5 fire and one injury allegations during the course of this investigation.Two fires occurred while the vehicles were parked.One originated in the vicinity of the driver?s side light assembly where the fire and associated damage was confined to the trunk area, and the fire self extinguished due to oxygen starvation.As a result of the fire, the vehicle was repurchased by Mercedes and salvaged.The second fire originated on the passenger's side and required fire department response to extinguish; the fire damaged the tail light and surrounding body panels as well as the trunk area and wiring.The vehicle was repaired and returned to service.Two firesoccurred while the vehicle was being driven.In the first instance, the driver detected an odor and pulled over to observe smoking and a small flame at the lighting assembly wiring in the trunk.The owner was able to extinguish the fire before any significant damage occurred.In the second instance, the driver smelled smoke, pulled over, and opened the trunk to find smoke and sparks emanating from the forward facing side of the tail light.The driver was able to extinguish the sparks and drive the vehicle to the dealer. A fifth fire was reported by a fleet manager who observed a vehicle with fire damage originating near one of the tail light assemblies.The injury incident occurred when a technician burned their hand while diagnosing a failed light.The technician touched the tail light wiring which was hot enough to burn him although the injury did not require medical attention.On April 10th, 2014, Mercedes notified ODI that it would conduct a safety recall to remedy the rear light assemblies in approximately 252,867 MY 2008 - 2011 C-Class vehicles including the C300, C350 and C63 AMG models.Each rear light assembly has separate bulbs that act as brake, tail lamp, backup and turn signal indicators.The bulbs are mounted in a bulb carrier which uses a common electrical ground circuit at the harness connection.According to Mercedes, oxidation due to the use of dissimilar metals on the harness and bulb carrier electrical connectors can result in increased resistance and a subsequent dimming or loss of lighting function.The heat caused by the increased resistance/oxidation can also lead to the melting of the surrounding plastic, or in some cases, present a fire hazard.In conducting recall 14V-171, Mercedes dealers will inspect the left and right bulb carriers and harness connectors for the presence of dissimilar electrical connectors and/or evidence of related thermal damage; affected bulb carriers and/or harness connectors will be replaced free of charge.Mercedes notes that service replacement bulb carriers produced from January 2012 eliminate the dissimilar metal condition and that these bulb carriers will not requ
Exterior Lighting:turn Signal
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) or illuminate dimly.In some reports, complainants also alleged that the failure was accompanied by a burning smell emanating from the trunk of the vehicle.When examined, these vehicles showed evidence of overheating at the lighting assembly harness connector, including damaged (blackened) wiring and plastic.The rear lighting failures typically involved one side of the vehicle however in some cases both assemblies failed (although probably not simultaneously).ODI identified 5 fire and one injury allegations during the course of this investigation.Two fires occurred while the vehicles were parked.One originated in the vicinity of the driver?s side light assembly where the fire and associated damage was confined to the trunk area, and the fire self extinguished due to oxygen starvation.As a result of the fire, the vehicle was repurchased by Mercedes and salvaged.The second fire originated on the passenger's side and required fire department response to extinguish; the fire damaged the tail light and surrounding body panels as well as the trunk area and wiring.The vehicle was repaired and returned to service.Two firesoccurred while the vehicle was being driven.In the first instance, the driver detected an odor and pulled over to observe smoking and a small flame at the lighting assembly wiring in the trunk.The owner was able to extinguish the fire before any significant damage occurred.In the second instance, the driver smelled smoke, pulled over, and opened the trunk to find smoke and sparks emanating from the forward facing side of the tail light.The driver was able to extinguish the sparks and drive the vehicle to the dealer. A fifth fire was reported by a fleet manager who observed a vehicle with fire damage originating near one of the tail light assemblies.The injury incident occurred when a technician burned their hand while diagnosing a failed light.The technician touched the tail light wiring which was hot enough to burn him although the injury did not require medical attention.On April 10th, 2014, Mercedes notified ODI that it would conduct a safety recall to remedy the rear light assemblies in approximately 252,867 MY 2008 - 2011 C-Class vehicles including the C300, C350 and C63 AMG models.Each rear light assembly has separate bulbs that act as brake, tail lamp, backup and turn signal indicators.The bulbs are mounted in a bulb carrier which uses a common electrical ground circuit at the harness connection.According to Mercedes, oxidation due to the use of dissimilar metals on the harness and bulb carrier electrical connectors can result in increased resistance and a subsequent dimming or loss of lighting function.The heat caused by the increased resistance/oxidation can also lead to the melting of the surrounding plastic, or in some cases, present a fire hazard.In conducting recall 14V-171, Mercedes dealers will inspect the left and right bulb carriers and harness connectors for the presence of dissimilar electrical connectors and/or evidence of related thermal damage; affected bulb carriers and/or harness connectors will be replaced free of charge.Mercedes notes that service replacement bulb carriers produced from January 2012 eliminate the dissimilar metal condition and that these bulb carriers will not requ
PE13026 · Loss Of Rear Tail Light Functionality
Opened Jul 11, 2013 · Closed Dec 30, 2013
Status: closed (inferred from source dates) · Electrical System; Exterior Lighting; Exterior Lighting:brake Lights; Exterior Lighting:tail Lights; Exterior Lighting:turn Signal
ODI initially received 21 reports of rear light assembly failure due to a melted electrical connector or housing.Since opening the initial , ODI has received a total of 114 complaints reflecting an ongoing and increasing trend.In each report, one or both rear light assemblies fail completely (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) when the electrical ground connection is compromised as a result of high resistance and subsequent thermal over-heating.According to Mercedes-Benz, the over-heating of the ground wire is caused by corrosion between the connectors in the ground circuit to the tail light.ODI is aware of a total of 5 reports alleging fire including one injury allegation as a result of this issue.Analysis of subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.As a result of the evidence presented, this investigation has been upgraded to EA13-008.
Additional source detail variants (5)
Electrical System
ODI initially received 21 reports of rear light assembly failure due to a melted electrical connector or housing.Since opening the initial , ODI has received a total of 114 complaints reflecting an ongoing and increasing trend.In each report, one or both rear light assemblies fail completely (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) when the electrical ground connection is compromised as a result of high resistance and subsequent thermal over-heating.According to Mercedes-Benz, the over-heating of the ground wire is caused by corrosion between the connectors in the ground circuit to the tail light.ODI is aware of a total of 5 reports alleging fire including one injury allegation as a result of this issue.Analysis of subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.As a result of the evidence presented, this investigation has been upgraded to EA13-008.
Exterior Lighting:brake Lights
ODI initially received 21 reports of rear light assembly failure due to a melted electrical connector or housing.Since opening the initial , ODI has received a total of 114 complaints reflecting an ongoing and increasing trend.In each report, one or both rear light assemblies fail completely (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) when the electrical ground connection is compromised as a result of high resistance and subsequent thermal over-heating.According to Mercedes-Benz, the over-heating of the ground wire is caused by corrosion between the connectors in the ground circuit to the tail light.ODI is aware of a total of 5 reports alleging fire including one injury allegation as a result of this issue.Analysis of subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.As a result of the evidence presented, this investigation has been upgraded to EA13-008.
Exterior Lighting
ODI initially received 21 reports of rear light assembly failure due to a melted electrical connector or housing.Since opening the initial , ODI has received a total of 114 complaints reflecting an ongoing and increasing trend.In each report, one or both rear light assemblies fail completely (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) when the electrical ground connection is compromised as a result of high resistance and subsequent thermal over-heating.According to Mercedes-Benz, the over-heating of the ground wire is caused by corrosion between the connectors in the ground circuit to the tail light.ODI is aware of a total of 5 reports alleging fire including one injury allegation as a result of this issue.Analysis of subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.As a result of the evidence presented, this investigation has been upgraded to EA13-008.
Exterior Lighting:tail Lights
ODI initially received 21 reports of rear light assembly failure due to a melted electrical connector or housing.Since opening the initial , ODI has received a total of 114 complaints reflecting an ongoing and increasing trend.In each report, one or both rear light assemblies fail completely (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) when the electrical ground connection is compromised as a result of high resistance and subsequent thermal over-heating.According to Mercedes-Benz, the over-heating of the ground wire is caused by corrosion between the connectors in the ground circuit to the tail light.ODI is aware of a total of 5 reports alleging fire including one injury allegation as a result of this issue.Analysis of subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.As a result of the evidence presented, this investigation has been upgraded to EA13-008.
Exterior Lighting:turn Signal
ODI initially received 21 reports of rear light assembly failure due to a melted electrical connector or housing.Since opening the initial , ODI has received a total of 114 complaints reflecting an ongoing and increasing trend.In each report, one or both rear light assemblies fail completely (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) when the electrical ground connection is compromised as a result of high resistance and subsequent thermal over-heating.According to Mercedes-Benz, the over-heating of the ground wire is caused by corrosion between the connectors in the ground circuit to the tail light.ODI is aware of a total of 5 reports alleging fire including one injury allegation as a result of this issue.Analysis of subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.As a result of the evidence presented, this investigation has been upgraded to EA13-008.