← New search

2011 Mazda MAZDA6

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2011 Mazda MAZDA6 do not stand out strongly from the model-year median of 105.

About this comparison →

How this year compares

Owner complaints by model year

Other model years Selected year
Compare all MAZDA6 years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

All reported categories

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

61 reports with mileage · 73 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Suspension. Review the 49 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 30 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Air Bags. Review the 28 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

8 crash reports1 fire reports6 injury reports

Suspension complaints

49 reports
Clear category filter
Mileage unknown · Jul 31, 2024
StructureSuspension

After getting the recall information about the front crossmember rusting out due to corrosion, I decided to check the rear crossmember on my car. WOW, the rear crossmember is SO much worse than the front one and I’ve read hundreds of similar stories about the exact same thing happening to other Mazda 6 sedans around these model …

Read full complaint

After getting the recall information about the front crossmember rusting out due to corrosion, I decided to check the rear crossmember on my car. WOW, the rear crossmember is SO much worse than the front one and I’ve read hundreds of similar stories about the exact same thing happening to other Mazda 6 sedans around these model years (2009-2013). The rear crossmember on my car, which supports the entire rear suspension is completely rusted thru in several spots and the lower end links aren’t even attached anymore because the brackets literally fell off and so now both back tires are leaning in at the top. It is very noticeable! Very unsafe to drive! I decided to park this car until a solution is reached with Mazda or the NHTSA on how to deal with this. I don’t know why the front crossmember was recalled but not the rear? There’s only 2 things that are rusted on my car, period…the front & rear crossmembers!

NHTSA ODI #11605695

129,000 miles · Jul 29, 2024
StructureSuspension

The contact owns a 2011 Mazda Mazda6. The contact stated that while the independent mechanic was performing an oil change on the vehicle, the independent mechanic informed the contact that the rear subframe was severely rusted with holes in the subframe. The vehicle was taken to the dealer, where it was determined that the rear …

Read full complaint

The contact owns a 2011 Mazda Mazda6. The contact stated that while the independent mechanic was performing an oil change on the vehicle, the independent mechanic informed the contact that the rear subframe was severely rusted with holes in the subframe. The vehicle was taken to the dealer, where it was determined that the rear subframe needed to be replaced. The vehicle was not repaired. The contact stated that the vehicle was previously repaired under NHTSA Campaign Number: 19V323000 (Structure, Suspension). The manufacturer was notified of the failure and informed the contact that the VIN was not included in the recall. The failure mileage was approximately 129,000.

NHTSA ODI #11605184

Mileage unknown · Jul 21, 2024
Suspension

I'm filing a complaint as to substandard steel being used in the rear crossmember/rear subframe. Extensive corrosion has been confirmed upon a state inspection, which requires replacement at my personal cost. The front engine cradle was replaced in 2019, per a recall notice for the same extensive corrosion problem. A safety issu…

Read full complaint

I'm filing a complaint as to substandard steel being used in the rear crossmember/rear subframe. Extensive corrosion has been confirmed upon a state inspection, which requires replacement at my personal cost. The front engine cradle was replaced in 2019, per a recall notice for the same extensive corrosion problem. A safety issue that needs to be addressed by Mazda.

NHTSA ODI #11603648

Mileage unknown · Jun 18, 2024
SteeringSuspension

Completely rusted rear crossmember subframe

NHTSA ODI #11595019

89,000 miles · May 6, 2024
StructureSuspension

The contact's daughter owns a 2011 Mazda Mazda6. The contact stated that while her daughter was driving at an undisclosed speed, the steering wheel inadvertently moved to the left at a 30–35-degree angle. Additionally, the rear end of the vehicle swayed while coming to a stop. The vehicle was taken to an independent mechanic, wh…

Read full complaint

The contact's daughter owns a 2011 Mazda Mazda6. The contact stated that while her daughter was driving at an undisclosed speed, the steering wheel inadvertently moved to the left at a 30–35-degree angle. Additionally, the rear end of the vehicle swayed while coming to a stop. The vehicle was taken to an independent mechanic, who determined that the crossmember was severely corroded and the front driver's side crossmember had cracked. The vehicle was then towed to the dealer, where it was diagnosed that the front sub frame, sub frame link, sway bar, sub frame nuts, and bolts needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and a case was opened. The contact related the failure to NHTSA Campaign Number: 19V323000 (Structure, Suspension); however, the VIN was not included in the recall. The failure mileage was approximately 89,000.

NHTSA ODI #11587143

Mileage unknown · Apr 2, 2024
Suspension

Rear subframe rusted and cracked in half when my daughter was on a major highway!

NHTSA ODI #11580652

Mileage unknown · Mar 16, 2024
Suspension

My 2011 Mazda 6 rear suspension broke while my wife was driving our car on the highway. It could have killed my wife and son. The frame is rusted so bad that the lower control arm broke away from the frame, the rear wheel is barely hanging on it by one bolt on the front control arm. It is very much a safety issue and Mazda needs…

Read full complaint

My 2011 Mazda 6 rear suspension broke while my wife was driving our car on the highway. It could have killed my wife and son. The frame is rusted so bad that the lower control arm broke away from the frame, the rear wheel is barely hanging on it by one bolt on the front control arm. It is very much a safety issue and Mazda needs to take charge of the problem before someone dies in their vehicle. Our car has 106215 miles on it and we still owe alot of money on this thing.

NHTSA ODI #11577809

Mileage unknown · Feb 7, 2024
StructureSuspension

The rear cross member/subframe is completely rusted in two and the rear lower forward control arm is detached from cross member/subframe on both sides. There is currently an active recall for the front cross member due to accelerated corrosion from road salt but I’m not aware of any inclusion of the rear frame or suspension comp…

Read full complaint

The rear cross member/subframe is completely rusted in two and the rear lower forward control arm is detached from cross member/subframe on both sides. There is currently an active recall for the front cross member due to accelerated corrosion from road salt but I’m not aware of any inclusion of the rear frame or suspension components tied in with this recall. It definitely needs added to it as this is VERY dangerous, possibly even more so than the front. Rest of the actual car body is fine, except for a little bit of surface rust. Please add this to the current corrosion recall! Car is registered in WV and is available for inspection anytime and I will be attaching pictures and I also have a video but it won’t let me post it on here.

NHTSA ODI #11570675

Mileage unknown · Dec 13, 2023
SteeringSuspension

Turning onto a road, heard a loud thud from the front passenger corner. Car steering became highly erratic. Parked the car, noticed the front passenger wheel was crooked. Took it to the nearest shop and they said the crossmember was rusted completely through and snapped, causing the control arm to lose control. Found out there i…

Read full complaint

Turning onto a road, heard a loud thud from the front passenger corner. Car steering became highly erratic. Parked the car, noticed the front passenger wheel was crooked. Took it to the nearest shop and they said the crossmember was rusted completely through and snapped, causing the control arm to lose control. Found out there is a recall for the car model and year for this exact issue, but my car wasn't covered by it, so I did not receive notification of it, but it clearly affects this VIN as well.

NHTSA ODI #11559875

Mileage unknown · Dec 9, 2023
Suspension

Noticed the left rear tire suddenly had a lot of negative camber and there were now clunking sounds while driving. Inspection showed that the rear crossmember is severely rusted with holes, cracks, and delamination. The left toe link mount is completely separated, the coil spring stoppers are detached and loose inside the spri…

Read full complaint

Noticed the left rear tire suddenly had a lot of negative camber and there were now clunking sounds while driving. Inspection showed that the rear crossmember is severely rusted with holes, cracks, and delamination. The left toe link mount is completely separated, the coil spring stoppers are detached and loose inside the springs, and the right coil spring has the top coil broken off. The front body connection of the rear crossmember is barely connected. The level of corrosion on the rest of the car is drastically less than the rear crossmember. Currently deciding whether and how to repair. (Pennsylvania)

NHTSA ODI #11559265

Official recalls

6

19V782000 · Air Bags:frontal:passenger Side:inflator Module

Oct 31, 2019

Mazda North American Operations (Mazda) is recalling certain 2007-2012 CX-7, CX-9, and 2009-2012 Maza6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began December 3, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 1317F. Note: This recall supersedes recalls 16V356 and 17V012.

19V323000 · Structure; Suspension:front:control Arm

Apr 25, 2019

Mazda North American Operations (Mazda) is recalling certain 2011-2013 Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland,Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. The front cross member may corrode after exposure to road salt.

Consequence & remedy

Consequence: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.

Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began June 13, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I. Note: This recall is an expansion of Recall 18V-631.

Additional source detail variants (2)

Structure

Mazda North American Operations (Mazda) is recalling certain 2011-2013 Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland,Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. The front cross member may corrode after exposure to road salt.

Consequence: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.

Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began June 13, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I. Note: This recall is an expansion of Recall 18V-631.

Suspension:front:control Arm

Mazda North American Operations (Mazda) is recalling certain 2011-2013 Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland,Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. The front cross member may corrode after exposure to road salt.

Consequence: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.

Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began June 13, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I. Note: This recall is an expansion of Recall 18V-631.

18V717000 · Air Bags:frontal:passenger Side:inflator Module

Oct 12, 2018

Mazda North American Operations (Mazda) is recalling certain 2014-2015 Mazda CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2011-2013 Mazda6, 2011-2012 CX-7, and 2011-2015 CX-9 sold, or ever registered in the states of Arizona, Arkansas, Delaware, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, West Virginia and the District of Columbia, or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2010-2013 Mazda6, 2010-2012 CX-7, and 2010-2015 CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began November 9, 2018. Owners may contact Mazda customer service at 1-800-222-5500, Option 4. Mazda's number for this recall is 1317F.

17V429000 · Air Bags:frontal:passenger Side:inflator Module

Jun 29, 2017

Mazda North America Operations (Mazda) is recalling certain 2009-2011 Mazda6, and 2007-2011 CX-7 and CX-9 vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the passenger frontal air bag inflator with an alternate inflator, free of charge. The recall began on August 30, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 16V356 and all vehicles that were not remedied under that campaign are now covered by this one.

14V114000 · Fuel System, Gasoline

Mar 11, 2014

Mazda North America Operations (Mazda) is recalling certain model year 2010-2012 Mazda6 vehicles manufactured September 14, 2009, through May 2, 2011, and equipped with 2.5L engine. In the affected vehicles, spiders may weave a web in the evaporative canister vent hose, blocking it and causing the fuel tank to have an excessive amount of negative pressure.

Consequence & remedy

Consequence: Negative pressure could cause the fuel tank to crack resulting in a fuel leak, increasing the risk of a fire.

Remedy: Mazda will notify owners, and dealers will reprogram the powertrain control module and inspect and clean the canister vent line. If a web was found in the line, the fuel tank and check valve on canister vent line will be replaced. These repairs will be done free of charge. The recall began on April 30, 2014. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number associated with this campaign is 7214C.

13V425000 · Latches/locks/linkages:doors:latch

Sep 24, 2013

Mazda is recalling certain model year 2009-2013 Mazda6 vehicles manufactured February 4, 2008, through August 24, 2012. The door latch mounting screws may become loose.

Consequence & remedy

Consequence: If all three door latch mounting screws become excessively loose the door latch mechanism would not engage and the door might open while the vehicle is in motion increasing the risk of accident or injury.

Remedy: Mazda will notify owners, and dealers will apply a thread locking adhesive to the door screws and retorque them, free of charge. The recall began on October 29, 2013. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number is 7013I.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

0

No exact-year investigations in this snapshot.