IllustrationWHILE PERFORMING MAINTENANCE ON 2010 MAZDA 6 IT WAS OBSERVED THERE WAS EXTENSIVE CORROSION TO THE FRONT SUBFRAME. IT IS VERY NEAR STEERING AND SUSPENSION COMPONENTS AND HAD THE FRAME FAILED WHILE DRIVING IT LIKELY WOULD HAVE RESULTED IN LACK OF CONTROL OF THE VEHICLE. PICTURE IS ATTACHED.
2010 Mazda MAZDA6
Owner reports · Recalls · Investigations
More warning signs than most MAZDA6 years
Owner complaints for the 2010 Mazda MAZDA6 are substantially higher than the model-year median of 105.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA6 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
140–25K
2725–50K
2250–75K
3275–100K
29100–150K
15150K+
139 reports with mileage · 86 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Structure. Review the 60 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 54 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Suspension. Review the 43 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
5 crash reports2 fire reports2 injury reports
Structure complaints
60 reportsTL* THE CONTACT OWNS A 2010 MAZDA 6. WHILE DRIVING APPROXIMATELY 30 MPH, THE STEERING WHEEL STARTED TO PULL TO THE RIGHT. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHO DETERMINED THAT THE PASSENGER SIDE SUBFRAME WAS SEVERELY CORRODED AND FLAKY. THE VEHICLE WAS NOT REPAIRED. THE VEHICLE WAS NOT TAKEN TO THE DEALER FOR DIAG…
Read full complaint
TL* THE CONTACT OWNS A 2010 MAZDA 6. WHILE DRIVING APPROXIMATELY 30 MPH, THE STEERING WHEEL STARTED TO PULL TO THE RIGHT. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHO DETERMINED THAT THE PASSENGER SIDE SUBFRAME WAS SEVERELY CORRODED AND FLAKY. THE VEHICLE WAS NOT REPAIRED. THE VEHICLE WAS NOT TAKEN TO THE DEALER FOR DIAGNOSTIC TESTING. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 200,00. THE VIN WAS UNAVAILABLE.
AS I WAS DRIVING DOWN THE INTERSTATE MY STEERING WHEEL ROTATED CLOCKWISE AND WAS AT AN ANGLE AND MY CAR CONTINUED TO GO STRAIGHT DOWN THE ROAD. IT FELT AS IF I WERE DRIVING ON ICE AND WAS VERY HARD TO CONTROL THE VEHICLE. WHILE MAKING A TURN MY FRONT TIRES BEGAN TO SQUEAL. IT WAS VERY HARD TO TURN. WHEN BRAKING THE CAR SHOOK DRA…
Read full complaint
AS I WAS DRIVING DOWN THE INTERSTATE MY STEERING WHEEL ROTATED CLOCKWISE AND WAS AT AN ANGLE AND MY CAR CONTINUED TO GO STRAIGHT DOWN THE ROAD. IT FELT AS IF I WERE DRIVING ON ICE AND WAS VERY HARD TO CONTROL THE VEHICLE. WHILE MAKING A TURN MY FRONT TIRES BEGAN TO SQUEAL. IT WAS VERY HARD TO TURN. WHEN BRAKING THE CAR SHOOK DRAMATICALLY. I TOOK IT TO A LOCAL AUTO MECHANIC BECAUSE I THOUGHT IT WAS POSSIBLY SOMETHING WITH THE STEERING. THE MECHANIC CALLED BACK AND WAS SHOCKED TO TELL ME THE SUB FRAME WAS COMPLETELY ROTTEN AND HAD BROKEN. IT WAS HARD FOR HIM TO BELIEVE THAT A CAR THAT WAS ONLY 8 YEARS OLD WOULD HAVE THAT MUCH CORROSION ON THE FRAME. I PURCHASED THE CAR BRAND NEW AND HAVE HAD THE CAR FOR THE ENTIRE 8 YEARS WITH NO ACCIDENTS AT ALL.
I WAS DRIVING HOME FROM WORK, WHEN I NOTICED THAT MY STEERING WAS NOT WORKING RIGHT. EVERY TIME I HIT A BUMP IN THE ROAD IT BECAME HARD TO CONTROL. TO STAY STRAIGHT, MY STEERING WHEEL HAD TO BE TURN ALMOST COMPLETELY LEFT. I FIGURED I WAS JUST BADLY OUT OF ALIGNMENT. I TOOK IT TO THE SHOP TO GET MY ALIGNMENT DONE, AND THEY TOLD …
Read full complaint
I WAS DRIVING HOME FROM WORK, WHEN I NOTICED THAT MY STEERING WAS NOT WORKING RIGHT. EVERY TIME I HIT A BUMP IN THE ROAD IT BECAME HARD TO CONTROL. TO STAY STRAIGHT, MY STEERING WHEEL HAD TO BE TURN ALMOST COMPLETELY LEFT. I FIGURED I WAS JUST BADLY OUT OF ALIGNMENT. I TOOK IT TO THE SHOP TO GET MY ALIGNMENT DONE, AND THEY TOLD ME THE SUB FRAME WAS ROTTED OUT. THE CAR IS ONLY 8 YEARS OLD AND WELL MAINTAINED. HE WAS NOT ABLE TO EXPLAIN WHY IT WAS ROTTED OUT, BUT THE REST OF THE UNDERNEATH LOOKED GOOD.
MY WIFE WAS DRIVING ON THE INTERSTATE AT 70 MPH WHEN ALL OF THE SUDDEN THE CAR VEERED TO THE RIGHT CAUSING HER TO GO INTO THE RIGHT LANE AS SHE WAS IN THE LEFT LANE. THANKFULLY NO ONE WAS BESIDE HER AND SHE WAS ABLE TO KEEP THE CAR UNDER CONTROL. SHE STOPPED AND CALLED ME AS I WAS AT WORK TO EXPLAIN WHAT HAD HAPPENED. SHE WAS J…
Read full complaint
MY WIFE WAS DRIVING ON THE INTERSTATE AT 70 MPH WHEN ALL OF THE SUDDEN THE CAR VEERED TO THE RIGHT CAUSING HER TO GO INTO THE RIGHT LANE AS SHE WAS IN THE LEFT LANE. THANKFULLY NO ONE WAS BESIDE HER AND SHE WAS ABLE TO KEEP THE CAR UNDER CONTROL. SHE STOPPED AND CALLED ME AS I WAS AT WORK TO EXPLAIN WHAT HAD HAPPENED. SHE WAS JUST A FEW MILES AWAY FROM THE EXIT IN WHICH WE LIVE JUST OFF THE INTERSTATE SO SHE WAS ABLE TO LIMP THE CAR HOME. LATER THAT EVENING WHEN I WENT TO LOOK AT IT I NOTICED IMMEDIATELY THAT THE PASSENGER TIRE WAS POINTING OUTWARD A LITTLE BIT. I JACKED THE CAR UP LOOKING TO SEE IF A TIE ROD OR CONTROL ARM HAD BROKE ONLY TO FIND THAT NEITHER HAD BROKE. I LOOKED AT THE FRAME AND SEEN HOW BADLY IT WAS RUSTED AND NOTICED IT ACTUALLY HAD BROKEN APART AND WAS SHIFTED. THIS AREA OF THE SUBFRAME IS DIRECTLY UNDER THE A/C UNIT WHICH DRIPS STRAIGHT DOWN ONTO THE FRAME AREA THAT IS ROTTED. WHICH IS OBVIOUSLY THE REASON THE THE FRAME RUSTED AND BROKE AND SHIFTED CAUSING THE TIRE TO POINT OUTWARD. CALLED MAZDA AND THEY SENT A TOW TRUCK TO RETRIEVE THE CAR. CURRENTLY WAITING ON THEIR INSPECTION AND A CALL FROM MAZDA CORP TO SEE IF THEY WILL BE COVERING THE REPAIR. AFTER READING EVERYONE ELSE'S ISSUES WITH THIS VERY SAME PROBLEM I'M ASSUMING MAZDA WILL TELL ME IT'S OUR PROBLEM. THE CAR IS ONLY 8 YEARS OLD AND I'VE SEEN OTHER'S WHO'S CAR ARE EVEN NEWER AND MAZDA IS TELLING EVERYONE IT'S NOT DEFECTIVE. I STRONGLY DISAGREE WITH IT NOT BEING A MANUFACTURED DEFECT WHEN CLEARING THE WATER FROM THE A/C DRIPPING DOWN IS CAUSING ALL THESE SUBFRAMES TO RUST MUCH FASTER THAN ANY OTHER PART OF THE FRAME. WE'LL SEE WHAT THEY SAY BUT I'M NOT HOLDING MY BREATH.... SEEMS AS THOUGH WE THE PEOPLE NEED TO BAND TOGETHER IN A CLASS ACTION AGAINST MAZDA BECAUSE THIS CLEARLY IS A PROBLEM FOR A LOT OF CONSUMERS. PRAY NO ONE EVER GETS KILLED DO TO LOSS OF CONTROL WHEN THE FRAMES DO BRK.
THE FRAME ON MY VEHICLE SPECIALLY THE 'CRADLE' ON THE PASSENGER SIDE FAILED WHILE BRAKING. SPECIFICALLY THE ''CRADLE' IS RUSTED AND SPLIT ALMOST ALL THE WAY THROUGH. THE VEHICLE IS NOW UNDRIVABLE. IT IS A SEVERE SAFETY RISK
I'D LIKE TO REPORT MY OBSERVATION IN REGARDS TO THE FOLLOWING INVESTIGATION: PE18006 UPON PERFORMING ROUTINE MAINTENANCE I OBSERVED HEAVY CORROSION OF THE SUBFRAME OF MY VEHICLE HEAVILY CONCENTRATED TOWARDS THE REAR ENDS OF SAID SUBFRAME. THE DAMAGE IS LARGELY CONCENTRATED ON THE PASSENGER SIDE OF THE SUB FRAME BUT BOTH DR…
Read full complaint
I'D LIKE TO REPORT MY OBSERVATION IN REGARDS TO THE FOLLOWING INVESTIGATION: PE18006 UPON PERFORMING ROUTINE MAINTENANCE I OBSERVED HEAVY CORROSION OF THE SUBFRAME OF MY VEHICLE HEAVILY CONCENTRATED TOWARDS THE REAR ENDS OF SAID SUBFRAME. THE DAMAGE IS LARGELY CONCENTRATED ON THE PASSENGER SIDE OF THE SUB FRAME BUT BOTH DRIVE AND PASSENGER SIDES ARE IN VARYING STATES OF CORROSION. I CAN CONTRIBUTE ADDITIONAL INFORMATION UPON REQUEST BUT I WANTED TO ADD TO THE ON-GOING INVESTIGATION THAT HEAVY CORROSION TO THE POINT OF ME QUESTIONING THE STRUCTURAL INTEGRITY OF SAID SUBFRAME IS FOR SURE AN ISSUE I'M EXPERIENCING. I HAVE NOT CHECKED THE WELDS TO THE VARIOUS SUSPENSION COMPONENTS ATTACHED TO SUB FRAME BUT THE PINCH WELDS ALONG THE INTERIOR EDGE OF THE SUB FRAME HAVE BEEN COMPROMISED ALLOWING THE INGRESS OF ADDITIONAL WATER WHICH I BELIEVE IS ACCELERATING THIS ISSUE. THE WHOLE LOWER SURFACE OF THE SUB FRAME TOWARDS THE REAR OF THE SUB FRAME HAS BEGUN CORRODING AS WELL AND THE PAINT COVERING THE SUB FRAME HAS BUBBLED UP OR SEPARATED ALONG THE EDGE OF THE CORROSION.
ON AM OF 06/08/2018, I FELT SOMETHING GIVE IN FRONT END - FELT LIKE A BROKEN STRUT INITIALLY. DRIVING HOME AT 55-60 MPH THAT AFTERNOON, CAR BECAME NOTICEABLY DIFFICULT TO CONTROL - PULLING HARD TO THE RIGHT WHICH CAUSED AUDIBLE METALLIC SCRAPING NOISES FROM INSIDE CAR AND REQUIRED ME TO KEEP STEERING WHEEL TURNED LEFT AT 30-45 D…
Read full complaint
ON AM OF 06/08/2018, I FELT SOMETHING GIVE IN FRONT END - FELT LIKE A BROKEN STRUT INITIALLY. DRIVING HOME AT 55-60 MPH THAT AFTERNOON, CAR BECAME NOTICEABLY DIFFICULT TO CONTROL - PULLING HARD TO THE RIGHT WHICH CAUSED AUDIBLE METALLIC SCRAPING NOISES FROM INSIDE CAR AND REQUIRED ME TO KEEP STEERING WHEEL TURNED LEFT AT 30-45 DEGREES IN ORDER TO MAINTAIN STRAIGHT LINE. CAR WAS VERY DIFFICULT TO TURN OR KEEP UNDER CONTROL. MADE IT TO FAMILY MEMBER'S HOUSE NEAR MY MECHANIC, AND MADE ARRANGEMENTS TO DROP CAR OFF. ON 06/12/2018, MECHANIC CALLED TO INFORM ME THAT RIGHT FRONT SUBFRAME/ENGINE CRADLE WAS RUSTED THROUGH TO THE POINT THAT IT HAD CRACKED. HE WAS SHOCKED THAT IT DIDN'T FAIL CATASTROPHICALLY AT SPEED ON HIGHWAY. MAZDA DEALER ADVISED TO CALL MAZDA DIRECTLY TO FILE COMPLAINT. MECHANIC COULD NOT FIND A USED/SALVAGED CRADLE TO MAKE REPAIRS AND MAZDA DEALER INFORMED HIM THAT A CRADLE THEY ORDERED IN DECEMBER 2017 HAD JUST ARRIVED IN MAY 2018 - QUOTED PRICE TO REPAIR WAS ROUGHLY $1,600 PARTS/$1,000+ LABOR. CAR WAS BOUGHT NEW IN SEPTEMBER 2010 AND HAS JUST SHY OF 84,000 MILES.
WHEN PERFORMING AN OIL CHANGE I NOTICED THAT THE SUBFRAME / ENGINE CRADLE ON THE PASSENGER SIDE NEAR THE RIGHT SUSPENSION WAS SEVERELY RUSTED. THE SUBFRAME IS NO LONGER STRUCTURALLY SOUND AND I HAVE PARKED THE VEHICLE UNTIL A REPAIR IS COMPLETED. THE VEHICLE IS NO LONGER SAFE TO BE ON THE ROAD. THE SEVERE CORROSION APPEARS TO BE…
Read full complaint
WHEN PERFORMING AN OIL CHANGE I NOTICED THAT THE SUBFRAME / ENGINE CRADLE ON THE PASSENGER SIDE NEAR THE RIGHT SUSPENSION WAS SEVERELY RUSTED. THE SUBFRAME IS NO LONGER STRUCTURALLY SOUND AND I HAVE PARKED THE VEHICLE UNTIL A REPAIR IS COMPLETED. THE VEHICLE IS NO LONGER SAFE TO BE ON THE ROAD. THE SEVERE CORROSION APPEARS TO BE ISOLATED TO THE RIGHT SIDE WITH THE REST OF THE SUBFRAME SHOWING SURFACE CORROSION NORMALLY SEEN IN AN AREA THAT USES ROAD SALT SUCH AS MINNESOTA. I BELIEVE THAT THE CAUSE OF THIS FAILURE IS THE AIR CONDITIONING EVAPORATOR DRAIN DRIPPING ON THE SUBFRAME. AS YOU CAN SEE IN THE ATTACHED PICTURES THERE IS NO DRAIN HOSE USED TO DIVERT THE WATER FROM THE EVAPORATOR AROUND THE FRAME AND OVERBOARD. THIS MOISTURE MIXED WITH THE ROAD SALT CREATED A DANGEROUS AMOUNT OF CORROSION ON A KEY STRUCTURAL COMPONENT. I AM GLAD I NOTICED THIS BEFORE AN ACCIDENT OCCURRED
AIR CONDITIONER DRIPS ON TO ENGINE CRADLE RESULTING IN ROT.
Official recalls
919V782000 · Air Bags:frontal:passenger Side:inflator Module
Oct 31, 2019
Mazda North American Operations (Mazda) is recalling certain 2007-2012 CX-7, CX-9, and 2009-2012 Maza6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began December 3, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 1317F. Note: This recall supersedes recalls 16V356 and 17V012.
18V717000 · Air Bags:frontal:passenger Side:inflator Module
Oct 12, 2018
Mazda North American Operations (Mazda) is recalling certain 2014-2015 Mazda CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2011-2013 Mazda6, 2011-2012 CX-7, and 2011-2015 CX-9 sold, or ever registered in the states of Arizona, Arkansas, Delaware, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, West Virginia and the District of Columbia, or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2010-2013 Mazda6, 2010-2012 CX-7, and 2010-2015 CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began November 9, 2018. Owners may contact Mazda customer service at 1-800-222-5500, Option 4. Mazda's number for this recall is 1317F.
18V631000 · Structure; Suspension:front:control Arm
Sep 14, 2018
Mazda North American Operations (Mazda) is recalling certain 2009-2010 Mazda Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. The front cross member may corrode after exposure to road salt.
Consequence & remedy
Consequence: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.
Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began March 18, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I.
Additional source detail variants (2)
Structure
Mazda North American Operations (Mazda) is recalling certain 2009-2010 Mazda Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. The front cross member may corrode after exposure to road salt.
Consequence: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.
Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began March 18, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I.
Suspension:front:control Arm
Mazda North American Operations (Mazda) is recalling certain 2009-2010 Mazda Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. The front cross member may corrode after exposure to road salt.
Consequence: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.
Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began March 18, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I.
18V018000 · Air Bags:frontal:passenger Side:inflator Module
Jan 9, 2018
Mazda North American Operations (Mazda) is recalling certain 2013 Mazda6 and CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2010 Mazda6, CX-7 and CX-9 vehicles sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2009 Mazda6, CX-7, and CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began March 2, 2018. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F.
17V429000 · Air Bags:frontal:passenger Side:inflator Module
Jun 29, 2017
Mazda North America Operations (Mazda) is recalling certain 2009-2011 Mazda6, and 2007-2011 CX-7 and CX-9 vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the passenger frontal air bag inflator with an alternate inflator, free of charge. The recall began on August 30, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 16V356 and all vehicles that were not remedied under that campaign are now covered by this one.
16V594000 · Air Bags; Air Bags:frontal:sensor/control MODULE-INACTIVE
Aug 11, 2016
Mazda North American Operations (Mazda) is recalling certain model year 2009-2010 Mazda6 vehicles manufactured February 4, 2008, to December 3, 2009. The protective coating may not have been properly applied to the air bag control unit (ACU) and, as a result, moisture may damage the unit causing it to malfunction.
Consequence & remedy
Consequence: Failure of the ACU would illuminate the air bag warning light and prevent the air bags from deploying in the event of a crash, increasing the risk of injury.
Remedy: Mazda dealers will replace the ACU, free of charge, however parts are not currently available. The recall began June 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9816H.
Additional source detail variants (2)
Air Bags:frontal:sensor/control MODULE-INACTIVE
Mazda North American Operations (Mazda) is recalling certain model year 2009-2010 Mazda6 vehicles manufactured February 4, 2008, to December 3, 2009. The protective coating may not have been properly applied to the air bag control unit (ACU) and, as a result, moisture may damage the unit causing it to malfunction.
Consequence: Failure of the ACU would illuminate the air bag warning light and prevent the air bags from deploying in the event of a crash, increasing the risk of injury.
Remedy: Mazda dealers will replace the ACU, free of charge, however parts are not currently available. The recall began June 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9816H.
Air Bags
Mazda North American Operations (Mazda) is recalling certain model year 2009-2010 Mazda6 vehicles manufactured February 4, 2008, to December 3, 2009. The protective coating may not have been properly applied to the air bag control unit (ACU) and, as a result, moisture may damage the unit causing it to malfunction.
Consequence: Failure of the ACU would illuminate the air bag warning light and prevent the air bags from deploying in the event of a crash, increasing the risk of injury.
Remedy: Mazda dealers will replace the ACU, free of charge, however parts are not currently available. The recall began June 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9816H.
14V114000 · Fuel System, Gasoline
Mar 11, 2014
Mazda North America Operations (Mazda) is recalling certain model year 2010-2012 Mazda6 vehicles manufactured September 14, 2009, through May 2, 2011, and equipped with 2.5L engine. In the affected vehicles, spiders may weave a web in the evaporative canister vent hose, blocking it and causing the fuel tank to have an excessive amount of negative pressure.
Consequence & remedy
Consequence: Negative pressure could cause the fuel tank to crack resulting in a fuel leak, increasing the risk of a fire.
Remedy: Mazda will notify owners, and dealers will reprogram the powertrain control module and inspect and clean the canister vent line. If a web was found in the line, the fuel tank and check valve on canister vent line will be replaced. These repairs will be done free of charge. The recall began on April 30, 2014. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number associated with this campaign is 7214C.
13V425000 · Latches/locks/linkages:doors:latch
Sep 24, 2013
Mazda is recalling certain model year 2009-2013 Mazda6 vehicles manufactured February 4, 2008, through August 24, 2012. The door latch mounting screws may become loose.
Consequence & remedy
Consequence: If all three door latch mounting screws become excessively loose the door latch mechanism would not engage and the door might open while the vehicle is in motion increasing the risk of accident or injury.
Remedy: Mazda will notify owners, and dealers will apply a thread locking adhesive to the door screws and retorque them, free of charge. The recall began on October 29, 2013. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number is 7013I.
11V134000 · Fuel System, Gasoline:storage:tank Assembly
Feb 25, 2011
MAZDA IS RECALLING CERTAIN MODEL YEAR 2009-2010 MAZDA6 VEHICLES MANUFACTURED FROM APRIL 8, 2008, THROUGH FEBRUARY 8, 2010. A CERTAIN TYPE OF SPIDER MAY WEAVE A WEB IN THE EVAPORATIVE CANISTER VENT LINE AND THIS MAY CAUSE A RESTRICTION IN THE LINE. IF THIS OCCURS, THE FUEL TANK PRESSURE MAY BECOME EXCESSIVELY NEGATIVE WHEN THE EMISSION CONTROL SYSTEM WORKS TO PURGE THE VAPORS FROM THE CANISTER.
Consequence & remedy
Consequence: AS THE CANISTER IS PURGED REPEATEDLY DURING NORMAL OPERATION, THE STRESS ON THE FUEL TANK MAY EVENTUALLY RESULT IN A CRACK, POTENTIALLY LEADING TO FUEL LEAKAGE AD AN INCREASED RISK OF FIRE.
Remedy: DEALERS WILL INSPECT AND CLEAN UP THE CANISTER VENT LINE, AND INSTALL A SPRING TO PREVENT THIS TYPE OF SPIDER FROM ENTERING THE VENT LINE. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE MARCH 25, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE18006 · Front Subframe Corrosion
Opened May 21, 2018 · Closed Nov 2, 2018
Status: closed (inferred from source dates) · Suspension; Suspension:front
In a letter dated September 14, 2018, Mazda North American Operations (Mazda) notified the National Highway Traffic Safety Administration (NHTSA) of a defect in the front subframe assemblies of model year (MY) 2009 through 2010 Mazda6 vehicles in certain states with high road salt use in winter months (Recall 18V-631). The recall covers approximately 48,814 vehicles that were sold or ever registered in the following states and District of Columbia:Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Mazda indicated that the recalled vehicles may have insufficient paint coating on the front cross member, which after continuous use in salt states may cause premature corrosion of the cross member. As the corrosion progresses over time, the structural integrity of the mounting point at the passenger side of the lower control arm may deteriorate and cause the steering alignment to change. If the steering alignment changes significantly while the vehicle is in motion this may increase the risk of a vehicle crash.ODI's analysis of complaints it has received from the public (VOQ's) and Mazda complaint data submitted in response to the information request letter for PE18-006 identified a total of 53 non-duplicative reports alleging incidents in which front cross-member corrosion had progressed to the stage of complete or partial separation of the subject steering or suspension components and another 98 reports alleging premature and/or excessive corrosion of the subject components with no separation. Mazda's recall will inspect the subframe and apply structural reinforcements, anti-corrosive wax and an AC drain tube free of charge. In cases of excessive corrosion, the subframe will be replaced free of charge.All 53 complaints alleging complete or partial separations involved vehicles that will be covered under Mazda's recall, resulting in a failure rate of 108.6 reports per 100,000 vehicles (R/100k) in the recalled population. When all complaints are analyzed by region, 150 involve vehicles included in Mazda's recall (307.3 R/100k) and just 1 involved a MY 2009 through 2010 Mazda6 vehicle not included in 18V-631 (2.8 R/100k). The field data indicate that Mazda's recall adequately covers vehicles with a risk of experiencing premature corrosion-related failure of the subject steering and suspension components in the subject vehicles. Based on Mazda's safety recall, this investigation is closed.The following VOQs allege loss or compromised steering control while vehicle was in motion:11115277, 11115790, 11128449, 10706604, 10846298, 10899584, 11019306, 11033821, 11048014, 11074634, 11078734, 11080014, 11083781, 11090944, 11091913, 11098279, 11101718, 11102209, 11102796, 11110606, 11110773, 11112830, 11113461, 11113963, 11114039, 11114567, 11114939, 11115303, 11119368, 11119423, 11121341, 11123997, 11124647, 11128648, 11128774, 11130281, 11132046, 11133295, 11133511, 11138829, 11139187, 11139486The following VOQs allege subframe corrosion detection prior to subframe failure:11141172, 11131161, 11129747, 11129349, 11129185, 11128591, 11128223, 11124644, 11122948, 11120047, 11119752, 11119362, 11118786, 11118242, 11115432, 11114568, 11114477, 11114061, 11105334, 11104096, 11103756, 11103724, 11101659, 11100420, 11099962, 11097874, 11084411, 11081783, 11034064, 11025276, 10956316Some VOQs have been omitted from this list due to duplicate VOQ submission between ODI records and Mazda records.
Additional source detail variants (2)
Suspension:front
In a letter dated September 14, 2018, Mazda North American Operations (Mazda) notified the National Highway Traffic Safety Administration (NHTSA) of a defect in the front subframe assemblies of model year (MY) 2009 through 2010 Mazda6 vehicles in certain states with high road salt use in winter months (Recall 18V-631). The recall covers approximately 48,814 vehicles that were sold or ever registered in the following states and District of Columbia:Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Mazda indicated that the recalled vehicles may have insufficient paint coating on the front cross member, which after continuous use in salt states may cause premature corrosion of the cross member. As the corrosion progresses over time, the structural integrity of the mounting point at the passenger side of the lower control arm may deteriorate and cause the steering alignment to change. If the steering alignment changes significantly while the vehicle is in motion this may increase the risk of a vehicle crash.ODI's analysis of complaints it has received from the public (VOQ's) and Mazda complaint data submitted in response to the information request letter for PE18-006 identified a total of 53 non-duplicative reports alleging incidents in which front cross-member corrosion had progressed to the stage of complete or partial separation of the subject steering or suspension components and another 98 reports alleging premature and/or excessive corrosion of the subject components with no separation. Mazda's recall will inspect the subframe and apply structural reinforcements, anti-corrosive wax and an AC drain tube free of charge. In cases of excessive corrosion, the subframe will be replaced free of charge.All 53 complaints alleging complete or partial separations involved vehicles that will be covered under Mazda's recall, resulting in a failure rate of 108.6 reports per 100,000 vehicles (R/100k) in the recalled population. When all complaints are analyzed by region, 150 involve vehicles included in Mazda's recall (307.3 R/100k) and just 1 involved a MY 2009 through 2010 Mazda6 vehicle not included in 18V-631 (2.8 R/100k). The field data indicate that Mazda's recall adequately covers vehicles with a risk of experiencing premature corrosion-related failure of the subject steering and suspension components in the subject vehicles. Based on Mazda's safety recall, this investigation is closed.The following VOQs allege loss or compromised steering control while vehicle was in motion:11115277, 11115790, 11128449, 10706604, 10846298, 10899584, 11019306, 11033821, 11048014, 11074634, 11078734, 11080014, 11083781, 11090944, 11091913, 11098279, 11101718, 11102209, 11102796, 11110606, 11110773, 11112830, 11113461, 11113963, 11114039, 11114567, 11114939, 11115303, 11119368, 11119423, 11121341, 11123997, 11124647, 11128648, 11128774, 11130281, 11132046, 11133295, 11133511, 11138829, 11139187, 11139486The following VOQs allege subframe corrosion detection prior to subframe failure:11141172, 11131161, 11129747, 11129349, 11129185, 11128591, 11128223, 11124644, 11122948, 11120047, 11119752, 11119362, 11118786, 11118242, 11115432, 11114568, 11114477, 11114061, 11105334, 11104096, 11103756, 11103724, 11101659, 11100420, 11099962, 11097874, 11084411, 11081783, 11034064, 11025276, 10956316Some VOQs have been omitted from this list due to duplicate VOQ submission between ODI records and Mazda records.
Suspension
In a letter dated September 14, 2018, Mazda North American Operations (Mazda) notified the National Highway Traffic Safety Administration (NHTSA) of a defect in the front subframe assemblies of model year (MY) 2009 through 2010 Mazda6 vehicles in certain states with high road salt use in winter months (Recall 18V-631). The recall covers approximately 48,814 vehicles that were sold or ever registered in the following states and District of Columbia:Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Mazda indicated that the recalled vehicles may have insufficient paint coating on the front cross member, which after continuous use in salt states may cause premature corrosion of the cross member. As the corrosion progresses over time, the structural integrity of the mounting point at the passenger side of the lower control arm may deteriorate and cause the steering alignment to change. If the steering alignment changes significantly while the vehicle is in motion this may increase the risk of a vehicle crash.ODI's analysis of complaints it has received from the public (VOQ's) and Mazda complaint data submitted in response to the information request letter for PE18-006 identified a total of 53 non-duplicative reports alleging incidents in which front cross-member corrosion had progressed to the stage of complete or partial separation of the subject steering or suspension components and another 98 reports alleging premature and/or excessive corrosion of the subject components with no separation. Mazda's recall will inspect the subframe and apply structural reinforcements, anti-corrosive wax and an AC drain tube free of charge. In cases of excessive corrosion, the subframe will be replaced free of charge.All 53 complaints alleging complete or partial separations involved vehicles that will be covered under Mazda's recall, resulting in a failure rate of 108.6 reports per 100,000 vehicles (R/100k) in the recalled population. When all complaints are analyzed by region, 150 involve vehicles included in Mazda's recall (307.3 R/100k) and just 1 involved a MY 2009 through 2010 Mazda6 vehicle not included in 18V-631 (2.8 R/100k). The field data indicate that Mazda's recall adequately covers vehicles with a risk of experiencing premature corrosion-related failure of the subject steering and suspension components in the subject vehicles. Based on Mazda's safety recall, this investigation is closed.The following VOQs allege loss or compromised steering control while vehicle was in motion:11115277, 11115790, 11128449, 10706604, 10846298, 10899584, 11019306, 11033821, 11048014, 11074634, 11078734, 11080014, 11083781, 11090944, 11091913, 11098279, 11101718, 11102209, 11102796, 11110606, 11110773, 11112830, 11113461, 11113963, 11114039, 11114567, 11114939, 11115303, 11119368, 11119423, 11121341, 11123997, 11124647, 11128648, 11128774, 11130281, 11132046, 11133295, 11133511, 11138829, 11139187, 11139486The following VOQs allege subframe corrosion detection prior to subframe failure:11141172, 11131161, 11129747, 11129349, 11129185, 11128591, 11128223, 11124644, 11122948, 11120047, 11119752, 11119362, 11118786, 11118242, 11115432, 11114568, 11114477, 11114061, 11105334, 11104096, 11103756, 11103724, 11101659, 11100420, 11099962, 11097874, 11084411, 11081783, 11034064, 11025276, 10956316Some VOQs have been omitted from this list due to duplicate VOQ submission between ODI records and Mazda records.