← New search

2010 Mazda MAZDA6

Owner reports · Recalls · Investigations

More warning signs than most MAZDA6 years

Owner complaints for the 2010 Mazda MAZDA6 are substantially higher than the model-year median of 105.

About this comparison →

When problems were reported

Mileage at the reported incident

139 reports with mileage · 86 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Structure. Review the 60 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Air Bags. Review the 54 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Suspension. Review the 43 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

5 crash reports2 fire reports2 injury reports

Exterior Lighting complaints

21 reports
Clear category filter
46,000 miles · May 23, 2011
Exterior Lighting

THE INNER TAIL LIGHT LENSES ON BOTH THE DRIVER & PASSENGER SIDE OF MY 2010 MAZDA 6 TOURING ARE PHYSICALLY MELTING AND BECOMING SEVERELY DEFORMED. THE OUTER, CLEAR LENSES ARE NOT DAMAGED AND THE MELTING IS ORIGINATING IN THE VICINITY OF THE BULBS. CAR HAS NOT BEEN ALTERED FROM THE MFG AND BULBS ARE MANUFACTURER RECOMMENDED. CAR…

Read full complaint

THE INNER TAIL LIGHT LENSES ON BOTH THE DRIVER & PASSENGER SIDE OF MY 2010 MAZDA 6 TOURING ARE PHYSICALLY MELTING AND BECOMING SEVERELY DEFORMED. THE OUTER, CLEAR LENSES ARE NOT DAMAGED AND THE MELTING IS ORIGINATING IN THE VICINITY OF THE BULBS. CAR HAS NOT BEEN ALTERED FROM THE MFG AND BULBS ARE MANUFACTURER RECOMMENDED. CAR HAS 48,000 MILES ON IT AND BEYOND THE 36,000 MFG WARRANTY THEREFORE MAZDA WILL NOT REPLACE THEM FOR FREE. I BELIEVE THIS IS A SUPPLIER, DESIGN OR MANUFACTURING DEFECT THAT CAN POSSIBLY CAUSE A FIRE OR REDUCED BRAKE LIGHT VISIBILITY AND THIS PART SHOULD NOT MELT. I HAVE PICTURES AND CAN SEND THEM AS REFERENCE. A SEARCH OF THE INTERNET SHOWED A FEW OTHER INCIDENTS WITH DEFECTIVE MAZDA TAIL LIGHTS ON OTHER MODELS AND YEARS SIMILAR TO THIS. I AM UNCERTAIN HOW WIDE SPREAD THIS SITUATION IS. PICTURES RECEIVED. UPDATED 06/14/11 *TR

NHTSA ODI #10402409

Official recalls

9

19V782000 · Air Bags:frontal:passenger Side:inflator Module

Oct 31, 2019

Mazda North American Operations (Mazda) is recalling certain 2007-2012 CX-7, CX-9, and 2009-2012 Maza6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began December 3, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 1317F. Note: This recall supersedes recalls 16V356 and 17V012.

18V717000 · Air Bags:frontal:passenger Side:inflator Module

Oct 12, 2018

Mazda North American Operations (Mazda) is recalling certain 2014-2015 Mazda CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2011-2013 Mazda6, 2011-2012 CX-7, and 2011-2015 CX-9 sold, or ever registered in the states of Arizona, Arkansas, Delaware, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, West Virginia and the District of Columbia, or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2010-2013 Mazda6, 2010-2012 CX-7, and 2010-2015 CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began November 9, 2018. Owners may contact Mazda customer service at 1-800-222-5500, Option 4. Mazda's number for this recall is 1317F.

18V631000 · Structure; Suspension:front:control Arm

Sep 14, 2018

Mazda North American Operations (Mazda) is recalling certain 2009-2010 Mazda Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. The front cross member may corrode after exposure to road salt.

Consequence & remedy

Consequence: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.

Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began March 18, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I.

Additional source detail variants (2)

Structure

Mazda North American Operations (Mazda) is recalling certain 2009-2010 Mazda Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. The front cross member may corrode after exposure to road salt.

Consequence: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.

Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began March 18, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I.

Suspension:front:control Arm

Mazda North American Operations (Mazda) is recalling certain 2009-2010 Mazda Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. The front cross member may corrode after exposure to road salt.

Consequence: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.

Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began March 18, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I.

18V018000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2018

Mazda North American Operations (Mazda) is recalling certain 2013 Mazda6 and CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2010 Mazda6, CX-7 and CX-9 vehicles sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2009 Mazda6, CX-7, and CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began March 2, 2018. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F.

17V429000 · Air Bags:frontal:passenger Side:inflator Module

Jun 29, 2017

Mazda North America Operations (Mazda) is recalling certain 2009-2011 Mazda6, and 2007-2011 CX-7 and CX-9 vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the passenger frontal air bag inflator with an alternate inflator, free of charge. The recall began on August 30, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 16V356 and all vehicles that were not remedied under that campaign are now covered by this one.

16V594000 · Air Bags; Air Bags:frontal:sensor/control MODULE-INACTIVE

Aug 11, 2016

Mazda North American Operations (Mazda) is recalling certain model year 2009-2010 Mazda6 vehicles manufactured February 4, 2008, to December 3, 2009. The protective coating may not have been properly applied to the air bag control unit (ACU) and, as a result, moisture may damage the unit causing it to malfunction.

Consequence & remedy

Consequence: Failure of the ACU would illuminate the air bag warning light and prevent the air bags from deploying in the event of a crash, increasing the risk of injury.

Remedy: Mazda dealers will replace the ACU, free of charge, however parts are not currently available. The recall began June 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9816H.

Additional source detail variants (2)

Air Bags:frontal:sensor/control MODULE-INACTIVE

Mazda North American Operations (Mazda) is recalling certain model year 2009-2010 Mazda6 vehicles manufactured February 4, 2008, to December 3, 2009. The protective coating may not have been properly applied to the air bag control unit (ACU) and, as a result, moisture may damage the unit causing it to malfunction.

Consequence: Failure of the ACU would illuminate the air bag warning light and prevent the air bags from deploying in the event of a crash, increasing the risk of injury.

Remedy: Mazda dealers will replace the ACU, free of charge, however parts are not currently available. The recall began June 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9816H.

Air Bags

Mazda North American Operations (Mazda) is recalling certain model year 2009-2010 Mazda6 vehicles manufactured February 4, 2008, to December 3, 2009. The protective coating may not have been properly applied to the air bag control unit (ACU) and, as a result, moisture may damage the unit causing it to malfunction.

Consequence: Failure of the ACU would illuminate the air bag warning light and prevent the air bags from deploying in the event of a crash, increasing the risk of injury.

Remedy: Mazda dealers will replace the ACU, free of charge, however parts are not currently available. The recall began June 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9816H.

14V114000 · Fuel System, Gasoline

Mar 11, 2014

Mazda North America Operations (Mazda) is recalling certain model year 2010-2012 Mazda6 vehicles manufactured September 14, 2009, through May 2, 2011, and equipped with 2.5L engine. In the affected vehicles, spiders may weave a web in the evaporative canister vent hose, blocking it and causing the fuel tank to have an excessive amount of negative pressure.

Consequence & remedy

Consequence: Negative pressure could cause the fuel tank to crack resulting in a fuel leak, increasing the risk of a fire.

Remedy: Mazda will notify owners, and dealers will reprogram the powertrain control module and inspect and clean the canister vent line. If a web was found in the line, the fuel tank and check valve on canister vent line will be replaced. These repairs will be done free of charge. The recall began on April 30, 2014. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number associated with this campaign is 7214C.

13V425000 · Latches/locks/linkages:doors:latch

Sep 24, 2013

Mazda is recalling certain model year 2009-2013 Mazda6 vehicles manufactured February 4, 2008, through August 24, 2012. The door latch mounting screws may become loose.

Consequence & remedy

Consequence: If all three door latch mounting screws become excessively loose the door latch mechanism would not engage and the door might open while the vehicle is in motion increasing the risk of accident or injury.

Remedy: Mazda will notify owners, and dealers will apply a thread locking adhesive to the door screws and retorque them, free of charge. The recall began on October 29, 2013. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number is 7013I.

11V134000 · Fuel System, Gasoline:storage:tank Assembly

Feb 25, 2011

MAZDA IS RECALLING CERTAIN MODEL YEAR 2009-2010 MAZDA6 VEHICLES MANUFACTURED FROM APRIL 8, 2008, THROUGH FEBRUARY 8, 2010. A CERTAIN TYPE OF SPIDER MAY WEAVE A WEB IN THE EVAPORATIVE CANISTER VENT LINE AND THIS MAY CAUSE A RESTRICTION IN THE LINE. IF THIS OCCURS, THE FUEL TANK PRESSURE MAY BECOME EXCESSIVELY NEGATIVE WHEN THE EMISSION CONTROL SYSTEM WORKS TO PURGE THE VAPORS FROM THE CANISTER.

Consequence & remedy

Consequence: AS THE CANISTER IS PURGED REPEATEDLY DURING NORMAL OPERATION, THE STRESS ON THE FUEL TANK MAY EVENTUALLY RESULT IN A CRACK, POTENTIALLY LEADING TO FUEL LEAKAGE AD AN INCREASED RISK OF FIRE.

Remedy: DEALERS WILL INSPECT AND CLEAN UP THE CANISTER VENT LINE, AND INSTALL A SPRING TO PREVENT THIS TYPE OF SPIDER FROM ENTERING THE VENT LINE. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE MARCH 25, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

PE18006 · Front Subframe Corrosion

Opened May 21, 2018 · Closed Nov 2, 2018

Status: closed (inferred from source dates) · Suspension; Suspension:front

In a letter dated September 14, 2018, Mazda North American Operations (Mazda) notified the National Highway Traffic Safety Administration (NHTSA) of a defect in the front subframe assemblies of model year (MY) 2009 through 2010 Mazda6 vehicles in certain states with high road salt use in winter months (Recall 18V-631). The recall covers approximately 48,814 vehicles that were sold or ever registered in the following states and District of Columbia:Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Mazda indicated that the recalled vehicles may have insufficient paint coating on the front cross member, which after continuous use in salt states may cause premature corrosion of the cross member. As the corrosion progresses over time, the structural integrity of the mounting point at the passenger side of the lower control arm may deteriorate and cause the steering alignment to change. If the steering alignment changes significantly while the vehicle is in motion this may increase the risk of a vehicle crash.ODI's analysis of complaints it has received from the public (VOQ's) and Mazda complaint data submitted in response to the information request letter for PE18-006 identified a total of 53 non-duplicative reports alleging incidents in which front cross-member corrosion had progressed to the stage of complete or partial separation of the subject steering or suspension components and another 98 reports alleging premature and/or excessive corrosion of the subject components with no separation. Mazda's recall will inspect the subframe and apply structural reinforcements, anti-corrosive wax and an AC drain tube free of charge. In cases of excessive corrosion, the subframe will be replaced free of charge.All 53 complaints alleging complete or partial separations involved vehicles that will be covered under Mazda's recall, resulting in a failure rate of 108.6 reports per 100,000 vehicles (R/100k) in the recalled population. When all complaints are analyzed by region, 150 involve vehicles included in Mazda's recall (307.3 R/100k) and just 1 involved a MY 2009 through 2010 Mazda6 vehicle not included in 18V-631 (2.8 R/100k). The field data indicate that Mazda's recall adequately covers vehicles with a risk of experiencing premature corrosion-related failure of the subject steering and suspension components in the subject vehicles. Based on Mazda's safety recall, this investigation is closed.The following VOQs allege loss or compromised steering control while vehicle was in motion:11115277, 11115790, 11128449, 10706604, 10846298, 10899584, 11019306, 11033821, 11048014, 11074634, 11078734, 11080014, 11083781, 11090944, 11091913, 11098279, 11101718, 11102209, 11102796, 11110606, 11110773, 11112830, 11113461, 11113963, 11114039, 11114567, 11114939, 11115303, 11119368, 11119423, 11121341, 11123997, 11124647, 11128648, 11128774, 11130281, 11132046, 11133295, 11133511, 11138829, 11139187, 11139486The following VOQs allege subframe corrosion detection prior to subframe failure:11141172, 11131161, 11129747, 11129349, 11129185, 11128591, 11128223, 11124644, 11122948, 11120047, 11119752, 11119362, 11118786, 11118242, 11115432, 11114568, 11114477, 11114061, 11105334, 11104096, 11103756, 11103724, 11101659, 11100420, 11099962, 11097874, 11084411, 11081783, 11034064, 11025276, 10956316Some VOQs have been omitted from this list due to duplicate VOQ submission between ODI records and Mazda records.

Additional source detail variants (2)

Suspension:front

In a letter dated September 14, 2018, Mazda North American Operations (Mazda) notified the National Highway Traffic Safety Administration (NHTSA) of a defect in the front subframe assemblies of model year (MY) 2009 through 2010 Mazda6 vehicles in certain states with high road salt use in winter months (Recall 18V-631). The recall covers approximately 48,814 vehicles that were sold or ever registered in the following states and District of Columbia:Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Mazda indicated that the recalled vehicles may have insufficient paint coating on the front cross member, which after continuous use in salt states may cause premature corrosion of the cross member. As the corrosion progresses over time, the structural integrity of the mounting point at the passenger side of the lower control arm may deteriorate and cause the steering alignment to change. If the steering alignment changes significantly while the vehicle is in motion this may increase the risk of a vehicle crash.ODI's analysis of complaints it has received from the public (VOQ's) and Mazda complaint data submitted in response to the information request letter for PE18-006 identified a total of 53 non-duplicative reports alleging incidents in which front cross-member corrosion had progressed to the stage of complete or partial separation of the subject steering or suspension components and another 98 reports alleging premature and/or excessive corrosion of the subject components with no separation. Mazda's recall will inspect the subframe and apply structural reinforcements, anti-corrosive wax and an AC drain tube free of charge. In cases of excessive corrosion, the subframe will be replaced free of charge.All 53 complaints alleging complete or partial separations involved vehicles that will be covered under Mazda's recall, resulting in a failure rate of 108.6 reports per 100,000 vehicles (R/100k) in the recalled population. When all complaints are analyzed by region, 150 involve vehicles included in Mazda's recall (307.3 R/100k) and just 1 involved a MY 2009 through 2010 Mazda6 vehicle not included in 18V-631 (2.8 R/100k). The field data indicate that Mazda's recall adequately covers vehicles with a risk of experiencing premature corrosion-related failure of the subject steering and suspension components in the subject vehicles. Based on Mazda's safety recall, this investigation is closed.The following VOQs allege loss or compromised steering control while vehicle was in motion:11115277, 11115790, 11128449, 10706604, 10846298, 10899584, 11019306, 11033821, 11048014, 11074634, 11078734, 11080014, 11083781, 11090944, 11091913, 11098279, 11101718, 11102209, 11102796, 11110606, 11110773, 11112830, 11113461, 11113963, 11114039, 11114567, 11114939, 11115303, 11119368, 11119423, 11121341, 11123997, 11124647, 11128648, 11128774, 11130281, 11132046, 11133295, 11133511, 11138829, 11139187, 11139486The following VOQs allege subframe corrosion detection prior to subframe failure:11141172, 11131161, 11129747, 11129349, 11129185, 11128591, 11128223, 11124644, 11122948, 11120047, 11119752, 11119362, 11118786, 11118242, 11115432, 11114568, 11114477, 11114061, 11105334, 11104096, 11103756, 11103724, 11101659, 11100420, 11099962, 11097874, 11084411, 11081783, 11034064, 11025276, 10956316Some VOQs have been omitted from this list due to duplicate VOQ submission between ODI records and Mazda records.

Suspension

In a letter dated September 14, 2018, Mazda North American Operations (Mazda) notified the National Highway Traffic Safety Administration (NHTSA) of a defect in the front subframe assemblies of model year (MY) 2009 through 2010 Mazda6 vehicles in certain states with high road salt use in winter months (Recall 18V-631). The recall covers approximately 48,814 vehicles that were sold or ever registered in the following states and District of Columbia:Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Mazda indicated that the recalled vehicles may have insufficient paint coating on the front cross member, which after continuous use in salt states may cause premature corrosion of the cross member. As the corrosion progresses over time, the structural integrity of the mounting point at the passenger side of the lower control arm may deteriorate and cause the steering alignment to change. If the steering alignment changes significantly while the vehicle is in motion this may increase the risk of a vehicle crash.ODI's analysis of complaints it has received from the public (VOQ's) and Mazda complaint data submitted in response to the information request letter for PE18-006 identified a total of 53 non-duplicative reports alleging incidents in which front cross-member corrosion had progressed to the stage of complete or partial separation of the subject steering or suspension components and another 98 reports alleging premature and/or excessive corrosion of the subject components with no separation. Mazda's recall will inspect the subframe and apply structural reinforcements, anti-corrosive wax and an AC drain tube free of charge. In cases of excessive corrosion, the subframe will be replaced free of charge.All 53 complaints alleging complete or partial separations involved vehicles that will be covered under Mazda's recall, resulting in a failure rate of 108.6 reports per 100,000 vehicles (R/100k) in the recalled population. When all complaints are analyzed by region, 150 involve vehicles included in Mazda's recall (307.3 R/100k) and just 1 involved a MY 2009 through 2010 Mazda6 vehicle not included in 18V-631 (2.8 R/100k). The field data indicate that Mazda's recall adequately covers vehicles with a risk of experiencing premature corrosion-related failure of the subject steering and suspension components in the subject vehicles. Based on Mazda's safety recall, this investigation is closed.The following VOQs allege loss or compromised steering control while vehicle was in motion:11115277, 11115790, 11128449, 10706604, 10846298, 10899584, 11019306, 11033821, 11048014, 11074634, 11078734, 11080014, 11083781, 11090944, 11091913, 11098279, 11101718, 11102209, 11102796, 11110606, 11110773, 11112830, 11113461, 11113963, 11114039, 11114567, 11114939, 11115303, 11119368, 11119423, 11121341, 11123997, 11124647, 11128648, 11128774, 11130281, 11132046, 11133295, 11133511, 11138829, 11139187, 11139486The following VOQs allege subframe corrosion detection prior to subframe failure:11141172, 11131161, 11129747, 11129349, 11129185, 11128591, 11128223, 11124644, 11122948, 11120047, 11119752, 11119362, 11118786, 11118242, 11115432, 11114568, 11114477, 11114061, 11105334, 11104096, 11103756, 11103724, 11101659, 11100420, 11099962, 11097874, 11084411, 11081783, 11034064, 11025276, 10956316Some VOQs have been omitted from this list due to duplicate VOQ submission between ODI records and Mazda records.