IllustrationThe rear sub frame on this vehicle was not painted and/or coated to properly withstand the corrosion that is caused by the salt used to treat the roads in the winter. This can cause serious issues.
2009 Mazda MAZDA6
Owner reports · Recalls · Investigations
More warning signs than most MAZDA6 years
Owner complaints for the 2009 Mazda MAZDA6 are substantially higher than the model-year median of 105.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA6 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
190–25K
4025–50K
5150–75K
4575–100K
66100–150K
29150K+
250 reports with mileage · 136 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Structure. Review the 123 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Suspension. Review the 76 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 75 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
8 crash reports3 fire reports4 injury reports
What owners actually said
386 reportsThere was a recall on the front subframe due to rust. The rear subframe has the same safety issue but there is no recall for that and there should be
The Rear Frame Suspension Cradle Subframe Crossmember has corroded and my mechanic at Jimmy's Tire and Auto in Granby Ct. says it is unsafe to drive. This corroded part is available for inspection while I wait for a used part to be delivered to complete the repair. No-one else has inspected the part. The condition was discove…
Read full complaint
The Rear Frame Suspension Cradle Subframe Crossmember has corroded and my mechanic at Jimmy's Tire and Auto in Granby Ct. says it is unsafe to drive. This corroded part is available for inspection while I wait for a used part to be delivered to complete the repair. No-one else has inspected the part. The condition was discovered when I had sent it in for general maintenance to replace the shocks and rear suspension linkages because there was noise in the rear when driving over bumps. The only warning I had was the odd noise when going over bumps in the road. I recall when buying the used vehicle many years ago that the dealer performed a recall on the front suspension #18V-631 and this shows closed.
The right side of the dashboard melts when the sun is out it’s very sticky and black comes off
While driving 40mph heard a pop, hissing sound and unable to steer vehicle. Stopped at roadside to examine tires, which were ok. Incredibly difficult to steer wheel and to stay on the road while swerving. I was within a mile of Belle Tire for a mechanic to look at my Mazda 6. He showed me how the open recall on the front crossme…
Read full complaint
While driving 40mph heard a pop, hissing sound and unable to steer vehicle. Stopped at roadside to examine tires, which were ok. Incredibly difficult to steer wheel and to stay on the road while swerving. I was within a mile of Belle Tire for a mechanic to look at my Mazda 6. He showed me how the open recall on the front crossmember was repaired only on the right wheel side, and the left front wheel had the same amount of rust completely broken apart. A phone call was made to the Mazda dealer closest, problem was relayed to service manager, and said even with my pictures, Mazda needs inspection on vehicle, and wait for repair was a month. As my only vehicle ,it took 2 days to get repaired by Belle Tire. I went with my receipt, and 10 photos, to the Service Department Manager that did the original recall work to discuss what transpired, and request a reimbursement for the incomplete repair on this open recall. He was not there. I then asked to speak to the Service Department Director. He also was not there. The Mechanic Supervisor took my name and phone number for one of the managers to call me regarding this problem. I have not received any communication from either Managers, which now has been since last week. There were NO warning lights on the dashboard when this occurred. I have had this vehicle since new, and only 61,000 miles.
Rear subframe corrosion/complete rot out, suspension complete rot out, and other components due to salt from the road and Mazda not correctly painting the components: 2009 Mazda 6I 2.5 Noticable drop in the back of the car. The tire wells are almost touching the rear tires. The rear tires are leaning inward, also putting inside…
Read full complaint
Rear subframe corrosion/complete rot out, suspension complete rot out, and other components due to salt from the road and Mazda not correctly painting the components: 2009 Mazda 6I 2.5 Noticable drop in the back of the car. The tire wells are almost touching the rear tires. The rear tires are leaning inward, also putting inside ware on the new tires. The rear of the vehicle fishtails while driving. It takes bumps very hard. No suspension. When you hit a bump, the rest of the car is all over the road. Very dangerous driving conditions, as the fishtailing throws you into other lanes, possibly into other traffic. Took vehicle to Meinke on 3-15-23, was told and shown the damages to the rear suspension and rear subframe and other rear components. Vehicle is not safe to drive until fixed. Called Mazda dealer, was notified of recall on front subframe, but not the rear. Have appointment on 3-29-23 to drop off at Mazda dealer to get the front subframe serviced. My front subframe is not the issue, not that I know of yet anyways. My rear is the issue. Why was it not recalled with the front? Why are they allowed to risk the lives and safety of so many for not servicing the rear also? This needs to be recalled, and I am definitely going as far as I can into getting something done about this. I do not have the funds to pay out of pocket to get this fixed, or funds to go out and buy a new car. I am a mother of a toddler, and disabled. I'm hoping to get a class action lawsuit against Mazda for this, or at the VERY least, a recall to fix this issue also. I live in Indiana, we have some snowy winters, so salt is used on the roadways. I believe the car came from Ohio before I purchased it from Kentucky. I purchased the car on March 27, 2021. Have only had "normal" maintenance issues or water and tare before this, and actually love the vehicle! It has been a great vehicle, other then this issue.
The rear subframe of my car is severely corroded. Both dampers (not sure if I have that name right, the cylinder inside the rear suspension coil) have rusted off. The rear left lateral control arm has rusted off. It is higher in mileage so it might be expected, except, other owners have reported the same problem with way less mi…
Read full complaint
The rear subframe of my car is severely corroded. Both dampers (not sure if I have that name right, the cylinder inside the rear suspension coil) have rusted off. The rear left lateral control arm has rusted off. It is higher in mileage so it might be expected, except, other owners have reported the same problem with way less miles. Also there was a recall for the front crossmember in salt states for the same issue but nothing issued for the rear. Driving on a rusted subframe could potentially cause major components of the rear end to rust and break off while driving causing an accident. If the front was poorly coated and had potential for severe premature corrosion, the back should also be addressed as well. Had there been something earlier many owners would not be facing the risk of a potential hazard.
Rear subframe rust got so bad the control arm snapped off and nearly killed my family.
Rear subframe rusted completely out
The rear subframe is absoutley rotted out from the car. Bought used and did not see until recently. Car was a Rhode Island car and was in Mass for a while. The rear wheels are concaved in and it is not only my car MULTIPLE owners of this generation car have experienced this these cars obly have the front subframe but not the rea…
Read full complaint
The rear subframe is absoutley rotted out from the car. Bought used and did not see until recently. Car was a Rhode Island car and was in Mass for a while. The rear wheels are concaved in and it is not only my car MULTIPLE owners of this generation car have experienced this these cars obly have the front subframe but not the rear! This particulat rear subframe is especially rotted THROUGH near the suspension! This is NOT ONLY MY CAR BYT MULTIPLES MAZDA 6'S!!! GOOGLE IT! I WILL SEND PICTURES LATER WHEN REQUESTED! IT IS LATE AND RAINING RIGHT NOW!
Official recalls
919V782000 · Air Bags:frontal:passenger Side:inflator Module
Oct 31, 2019
Mazda North American Operations (Mazda) is recalling certain 2007-2012 CX-7, CX-9, and 2009-2012 Maza6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began December 3, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 1317F. Note: This recall supersedes recalls 16V356 and 17V012.
18V631000 · Structure; Suspension:front:control Arm
Sep 14, 2018
Mazda North American Operations (Mazda) is recalling certain 2009-2010 Mazda Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. The front cross member may corrode after exposure to road salt.
Consequence & remedy
Consequence: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.
Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began March 18, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I.
Additional source detail variants (2)
Structure
Mazda North American Operations (Mazda) is recalling certain 2009-2010 Mazda Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. The front cross member may corrode after exposure to road salt.
Consequence: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.
Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began March 18, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I.
Suspension:front:control Arm
Mazda North American Operations (Mazda) is recalling certain 2009-2010 Mazda Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. The front cross member may corrode after exposure to road salt.
Consequence: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.
Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began March 18, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I.
18V018000 · Air Bags:frontal:passenger Side:inflator Module
Jan 9, 2018
Mazda North American Operations (Mazda) is recalling certain 2013 Mazda6 and CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2010 Mazda6, CX-7 and CX-9 vehicles sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2009 Mazda6, CX-7, and CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began March 2, 2018. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F.
17V457000 · Air Bags:frontal:passenger Side:inflator Module
Jul 18, 2017
Mazda North America Operations (Mazda) is recalling certain 2012 CX-7, CX-9 and Mazda6 vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Mazda is recalling certain 2009 CX-7, CX-9 and Mazda6 vehicles sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Mazda is recalling certain 2007-2008 CX-7 and CX-9 sold, or ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the front passenger side air bag inflator with an alternate inflator, free of charge. The recall began October 4, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 17V-012.
17V429000 · Air Bags:frontal:passenger Side:inflator Module
Jun 29, 2017
Mazda North America Operations (Mazda) is recalling certain 2009-2011 Mazda6, and 2007-2011 CX-7 and CX-9 vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the passenger frontal air bag inflator with an alternate inflator, free of charge. The recall began on August 30, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 16V356 and all vehicles that were not remedied under that campaign are now covered by this one.
16V594000 · Air Bags; Air Bags:frontal:sensor/control MODULE-INACTIVE
Aug 11, 2016
Mazda North American Operations (Mazda) is recalling certain model year 2009-2010 Mazda6 vehicles manufactured February 4, 2008, to December 3, 2009. The protective coating may not have been properly applied to the air bag control unit (ACU) and, as a result, moisture may damage the unit causing it to malfunction.
Consequence & remedy
Consequence: Failure of the ACU would illuminate the air bag warning light and prevent the air bags from deploying in the event of a crash, increasing the risk of injury.
Remedy: Mazda dealers will replace the ACU, free of charge, however parts are not currently available. The recall began June 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9816H.
Additional source detail variants (2)
Air Bags:frontal:sensor/control MODULE-INACTIVE
Mazda North American Operations (Mazda) is recalling certain model year 2009-2010 Mazda6 vehicles manufactured February 4, 2008, to December 3, 2009. The protective coating may not have been properly applied to the air bag control unit (ACU) and, as a result, moisture may damage the unit causing it to malfunction.
Consequence: Failure of the ACU would illuminate the air bag warning light and prevent the air bags from deploying in the event of a crash, increasing the risk of injury.
Remedy: Mazda dealers will replace the ACU, free of charge, however parts are not currently available. The recall began June 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9816H.
Air Bags
Mazda North American Operations (Mazda) is recalling certain model year 2009-2010 Mazda6 vehicles manufactured February 4, 2008, to December 3, 2009. The protective coating may not have been properly applied to the air bag control unit (ACU) and, as a result, moisture may damage the unit causing it to malfunction.
Consequence: Failure of the ACU would illuminate the air bag warning light and prevent the air bags from deploying in the event of a crash, increasing the risk of injury.
Remedy: Mazda dealers will replace the ACU, free of charge, however parts are not currently available. The recall began June 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9816H.
13V425000 · Latches/locks/linkages:doors:latch
Sep 24, 2013
Mazda is recalling certain model year 2009-2013 Mazda6 vehicles manufactured February 4, 2008, through August 24, 2012. The door latch mounting screws may become loose.
Consequence & remedy
Consequence: If all three door latch mounting screws become excessively loose the door latch mechanism would not engage and the door might open while the vehicle is in motion increasing the risk of accident or injury.
Remedy: Mazda will notify owners, and dealers will apply a thread locking adhesive to the door screws and retorque them, free of charge. The recall began on October 29, 2013. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number is 7013I.
11V134000 · Fuel System, Gasoline:storage:tank Assembly
Feb 25, 2011
MAZDA IS RECALLING CERTAIN MODEL YEAR 2009-2010 MAZDA6 VEHICLES MANUFACTURED FROM APRIL 8, 2008, THROUGH FEBRUARY 8, 2010. A CERTAIN TYPE OF SPIDER MAY WEAVE A WEB IN THE EVAPORATIVE CANISTER VENT LINE AND THIS MAY CAUSE A RESTRICTION IN THE LINE. IF THIS OCCURS, THE FUEL TANK PRESSURE MAY BECOME EXCESSIVELY NEGATIVE WHEN THE EMISSION CONTROL SYSTEM WORKS TO PURGE THE VAPORS FROM THE CANISTER.
Consequence & remedy
Consequence: AS THE CANISTER IS PURGED REPEATEDLY DURING NORMAL OPERATION, THE STRESS ON THE FUEL TANK MAY EVENTUALLY RESULT IN A CRACK, POTENTIALLY LEADING TO FUEL LEAKAGE AD AN INCREASED RISK OF FIRE.
Remedy: DEALERS WILL INSPECT AND CLEAN UP THE CANISTER VENT LINE, AND INSTALL A SPRING TO PREVENT THIS TYPE OF SPIDER FROM ENTERING THE VENT LINE. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE MARCH 25, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
09V043000 · Structure:body:door:hinge And Attachments
Feb 4, 2009
MAZDA IS RECALLING 29,000 MY 2009 MAZDA6. THE OUTER DOOR HANDLES MAY STICK WHICH MAY PREVENT THE DOOR FROM LATCHING. THIS SITUATION MAY ALLOW THE DOOR TO OPEN WHILE THE VEHICLE IS IN MOTION.
Consequence & remedy
Consequence: DRIVING THE VEHICLE WITH THE DOOR UNLATCHED COULD LEAD TO AN UNBELTED OCCUPANT BEING EJECTED AND COULD RESULT IN DEATH OR INJURY.
Remedy: DEALERS WILL INSPECT THE DOOR HANDLES AND IF NECESSARY REPAIR OR REPLACE THE HANDLES FREE OF CHARGE. THE RECALL BEGAN ON FEBRUARY 13, 2009. OWNERS MAY CONTACT MAZDA AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2PE18006 · Front Subframe Corrosion
Opened May 21, 2018 · Closed Nov 2, 2018
Status: closed (inferred from source dates) · Suspension; Suspension:front
In a letter dated September 14, 2018, Mazda North American Operations (Mazda) notified the National Highway Traffic Safety Administration (NHTSA) of a defect in the front subframe assemblies of model year (MY) 2009 through 2010 Mazda6 vehicles in certain states with high road salt use in winter months (Recall 18V-631). The recall covers approximately 48,814 vehicles that were sold or ever registered in the following states and District of Columbia:Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Mazda indicated that the recalled vehicles may have insufficient paint coating on the front cross member, which after continuous use in salt states may cause premature corrosion of the cross member. As the corrosion progresses over time, the structural integrity of the mounting point at the passenger side of the lower control arm may deteriorate and cause the steering alignment to change. If the steering alignment changes significantly while the vehicle is in motion this may increase the risk of a vehicle crash.ODI's analysis of complaints it has received from the public (VOQ's) and Mazda complaint data submitted in response to the information request letter for PE18-006 identified a total of 53 non-duplicative reports alleging incidents in which front cross-member corrosion had progressed to the stage of complete or partial separation of the subject steering or suspension components and another 98 reports alleging premature and/or excessive corrosion of the subject components with no separation. Mazda's recall will inspect the subframe and apply structural reinforcements, anti-corrosive wax and an AC drain tube free of charge. In cases of excessive corrosion, the subframe will be replaced free of charge.All 53 complaints alleging complete or partial separations involved vehicles that will be covered under Mazda's recall, resulting in a failure rate of 108.6 reports per 100,000 vehicles (R/100k) in the recalled population. When all complaints are analyzed by region, 150 involve vehicles included in Mazda's recall (307.3 R/100k) and just 1 involved a MY 2009 through 2010 Mazda6 vehicle not included in 18V-631 (2.8 R/100k). The field data indicate that Mazda's recall adequately covers vehicles with a risk of experiencing premature corrosion-related failure of the subject steering and suspension components in the subject vehicles. Based on Mazda's safety recall, this investigation is closed.The following VOQs allege loss or compromised steering control while vehicle was in motion:11115277, 11115790, 11128449, 10706604, 10846298, 10899584, 11019306, 11033821, 11048014, 11074634, 11078734, 11080014, 11083781, 11090944, 11091913, 11098279, 11101718, 11102209, 11102796, 11110606, 11110773, 11112830, 11113461, 11113963, 11114039, 11114567, 11114939, 11115303, 11119368, 11119423, 11121341, 11123997, 11124647, 11128648, 11128774, 11130281, 11132046, 11133295, 11133511, 11138829, 11139187, 11139486The following VOQs allege subframe corrosion detection prior to subframe failure:11141172, 11131161, 11129747, 11129349, 11129185, 11128591, 11128223, 11124644, 11122948, 11120047, 11119752, 11119362, 11118786, 11118242, 11115432, 11114568, 11114477, 11114061, 11105334, 11104096, 11103756, 11103724, 11101659, 11100420, 11099962, 11097874, 11084411, 11081783, 11034064, 11025276, 10956316Some VOQs have been omitted from this list due to duplicate VOQ submission between ODI records and Mazda records.
Additional source detail variants (2)
Suspension:front
In a letter dated September 14, 2018, Mazda North American Operations (Mazda) notified the National Highway Traffic Safety Administration (NHTSA) of a defect in the front subframe assemblies of model year (MY) 2009 through 2010 Mazda6 vehicles in certain states with high road salt use in winter months (Recall 18V-631). The recall covers approximately 48,814 vehicles that were sold or ever registered in the following states and District of Columbia:Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Mazda indicated that the recalled vehicles may have insufficient paint coating on the front cross member, which after continuous use in salt states may cause premature corrosion of the cross member. As the corrosion progresses over time, the structural integrity of the mounting point at the passenger side of the lower control arm may deteriorate and cause the steering alignment to change. If the steering alignment changes significantly while the vehicle is in motion this may increase the risk of a vehicle crash.ODI's analysis of complaints it has received from the public (VOQ's) and Mazda complaint data submitted in response to the information request letter for PE18-006 identified a total of 53 non-duplicative reports alleging incidents in which front cross-member corrosion had progressed to the stage of complete or partial separation of the subject steering or suspension components and another 98 reports alleging premature and/or excessive corrosion of the subject components with no separation. Mazda's recall will inspect the subframe and apply structural reinforcements, anti-corrosive wax and an AC drain tube free of charge. In cases of excessive corrosion, the subframe will be replaced free of charge.All 53 complaints alleging complete or partial separations involved vehicles that will be covered under Mazda's recall, resulting in a failure rate of 108.6 reports per 100,000 vehicles (R/100k) in the recalled population. When all complaints are analyzed by region, 150 involve vehicles included in Mazda's recall (307.3 R/100k) and just 1 involved a MY 2009 through 2010 Mazda6 vehicle not included in 18V-631 (2.8 R/100k). The field data indicate that Mazda's recall adequately covers vehicles with a risk of experiencing premature corrosion-related failure of the subject steering and suspension components in the subject vehicles. Based on Mazda's safety recall, this investigation is closed.The following VOQs allege loss or compromised steering control while vehicle was in motion:11115277, 11115790, 11128449, 10706604, 10846298, 10899584, 11019306, 11033821, 11048014, 11074634, 11078734, 11080014, 11083781, 11090944, 11091913, 11098279, 11101718, 11102209, 11102796, 11110606, 11110773, 11112830, 11113461, 11113963, 11114039, 11114567, 11114939, 11115303, 11119368, 11119423, 11121341, 11123997, 11124647, 11128648, 11128774, 11130281, 11132046, 11133295, 11133511, 11138829, 11139187, 11139486The following VOQs allege subframe corrosion detection prior to subframe failure:11141172, 11131161, 11129747, 11129349, 11129185, 11128591, 11128223, 11124644, 11122948, 11120047, 11119752, 11119362, 11118786, 11118242, 11115432, 11114568, 11114477, 11114061, 11105334, 11104096, 11103756, 11103724, 11101659, 11100420, 11099962, 11097874, 11084411, 11081783, 11034064, 11025276, 10956316Some VOQs have been omitted from this list due to duplicate VOQ submission between ODI records and Mazda records.
Suspension
In a letter dated September 14, 2018, Mazda North American Operations (Mazda) notified the National Highway Traffic Safety Administration (NHTSA) of a defect in the front subframe assemblies of model year (MY) 2009 through 2010 Mazda6 vehicles in certain states with high road salt use in winter months (Recall 18V-631). The recall covers approximately 48,814 vehicles that were sold or ever registered in the following states and District of Columbia:Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Mazda indicated that the recalled vehicles may have insufficient paint coating on the front cross member, which after continuous use in salt states may cause premature corrosion of the cross member. As the corrosion progresses over time, the structural integrity of the mounting point at the passenger side of the lower control arm may deteriorate and cause the steering alignment to change. If the steering alignment changes significantly while the vehicle is in motion this may increase the risk of a vehicle crash.ODI's analysis of complaints it has received from the public (VOQ's) and Mazda complaint data submitted in response to the information request letter for PE18-006 identified a total of 53 non-duplicative reports alleging incidents in which front cross-member corrosion had progressed to the stage of complete or partial separation of the subject steering or suspension components and another 98 reports alleging premature and/or excessive corrosion of the subject components with no separation. Mazda's recall will inspect the subframe and apply structural reinforcements, anti-corrosive wax and an AC drain tube free of charge. In cases of excessive corrosion, the subframe will be replaced free of charge.All 53 complaints alleging complete or partial separations involved vehicles that will be covered under Mazda's recall, resulting in a failure rate of 108.6 reports per 100,000 vehicles (R/100k) in the recalled population. When all complaints are analyzed by region, 150 involve vehicles included in Mazda's recall (307.3 R/100k) and just 1 involved a MY 2009 through 2010 Mazda6 vehicle not included in 18V-631 (2.8 R/100k). The field data indicate that Mazda's recall adequately covers vehicles with a risk of experiencing premature corrosion-related failure of the subject steering and suspension components in the subject vehicles. Based on Mazda's safety recall, this investigation is closed.The following VOQs allege loss or compromised steering control while vehicle was in motion:11115277, 11115790, 11128449, 10706604, 10846298, 10899584, 11019306, 11033821, 11048014, 11074634, 11078734, 11080014, 11083781, 11090944, 11091913, 11098279, 11101718, 11102209, 11102796, 11110606, 11110773, 11112830, 11113461, 11113963, 11114039, 11114567, 11114939, 11115303, 11119368, 11119423, 11121341, 11123997, 11124647, 11128648, 11128774, 11130281, 11132046, 11133295, 11133511, 11138829, 11139187, 11139486The following VOQs allege subframe corrosion detection prior to subframe failure:11141172, 11131161, 11129747, 11129349, 11129185, 11128591, 11128223, 11124644, 11122948, 11120047, 11119752, 11119362, 11118786, 11118242, 11115432, 11114568, 11114477, 11114061, 11105334, 11104096, 11103756, 11103724, 11101659, 11100420, 11099962, 11097874, 11084411, 11081783, 11034064, 11025276, 10956316Some VOQs have been omitted from this list due to duplicate VOQ submission between ODI records and Mazda records.
PE13015 · Door Latch Failures Due To Loose Screws
Opened May 9, 2013 · Closed Sep 30, 2013
Status: closed (inferred from source dates) · Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation based on reports that the doors were failing to properly latch on model year (MY) 2009 Mazda6 vehicles.Complainants alleged that the door would fail to latch, or would not properly latch. ODI received a total of 9 complaints alleging this condition primarily on the front side doors, however any of the four side doors could be affected.In response to ODI's Information Request, Mazda provided 56 consumer complaints related to the alleged problem, and 329 warranty claims.On September 23, 2013, Mazda notified ODI that it would conduct a safety recall on model year 2009-2013 Mazda6 vehicles built from February 4, 2008 through August 24, 2012. This period covers the start of production of the MY 2009 Mazda6 through the end of production for the 2013 model year and totals a population of approximately 161,400 vehicles. Mazda determined that the door latch mounting screws may become loose due to lack of torque during manufacturing and/or unevenness of the door shell in the latch mounting area. If all three door latch mounting screws become loose, the door latch mechanism may not engage, potentially resulting in the doors opening while the vehicle is in motion.To remedy the condition, a thread locking adhesive will be applied to the latch screws on all side doors, and the screws will be tightened to the specified torque.This investigation is closed on the basis of Mazda's announcement of safety recall 13V-425.ODI reports cited above can be reviewed at http://www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers: 10406174, 10448036, 10492403, 10503682, 10508051, 10515258, 10521830, 10535228, 10544489.
Additional source detail variants (2)
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation based on reports that the doors were failing to properly latch on model year (MY) 2009 Mazda6 vehicles.Complainants alleged that the door would fail to latch, or would not properly latch. ODI received a total of 9 complaints alleging this condition primarily on the front side doors, however any of the four side doors could be affected.In response to ODI's Information Request, Mazda provided 56 consumer complaints related to the alleged problem, and 329 warranty claims.On September 23, 2013, Mazda notified ODI that it would conduct a safety recall on model year 2009-2013 Mazda6 vehicles built from February 4, 2008 through August 24, 2012. This period covers the start of production of the MY 2009 Mazda6 through the end of production for the 2013 model year and totals a population of approximately 161,400 vehicles. Mazda determined that the door latch mounting screws may become loose due to lack of torque during manufacturing and/or unevenness of the door shell in the latch mounting area. If all three door latch mounting screws become loose, the door latch mechanism may not engage, potentially resulting in the doors opening while the vehicle is in motion.To remedy the condition, a thread locking adhesive will be applied to the latch screws on all side doors, and the screws will be tightened to the specified torque.This investigation is closed on the basis of Mazda's announcement of safety recall 13V-425.ODI reports cited above can be reviewed at http://www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers: 10406174, 10448036, 10492403, 10503682, 10508051, 10515258, 10521830, 10535228, 10544489.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation based on reports that the doors were failing to properly latch on model year (MY) 2009 Mazda6 vehicles.Complainants alleged that the door would fail to latch, or would not properly latch. ODI received a total of 9 complaints alleging this condition primarily on the front side doors, however any of the four side doors could be affected.In response to ODI's Information Request, Mazda provided 56 consumer complaints related to the alleged problem, and 329 warranty claims.On September 23, 2013, Mazda notified ODI that it would conduct a safety recall on model year 2009-2013 Mazda6 vehicles built from February 4, 2008 through August 24, 2012. This period covers the start of production of the MY 2009 Mazda6 through the end of production for the 2013 model year and totals a population of approximately 161,400 vehicles. Mazda determined that the door latch mounting screws may become loose due to lack of torque during manufacturing and/or unevenness of the door shell in the latch mounting area. If all three door latch mounting screws become loose, the door latch mechanism may not engage, potentially resulting in the doors opening while the vehicle is in motion.To remedy the condition, a thread locking adhesive will be applied to the latch screws on all side doors, and the screws will be tightened to the specified torque.This investigation is closed on the basis of Mazda's announcement of safety recall 13V-425.ODI reports cited above can be reviewed at http://www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers: 10406174, 10448036, 10492403, 10503682, 10508051, 10515258, 10521830, 10535228, 10544489.