IllustrationTHE TIRE VALVE STEM CRACKED WHILE CHECKING AIR PRESSURE ON ONE OF THE TIRES. AFTER THAT THE OTHER STEMS LOOKED LIKE THEY WERE READY TO FAIL. HAD THEM ALL REPLACED. *TR
2008 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2008 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
620–25K
8925–50K
4050–75K
3475–100K
25100–150K
6150K+
256 reports with mileage · 47 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 117 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 41 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Wheels. Review the 33 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
29 crash reports1 fire reports16 injury reports
What owners actually said
303 reports2008 MAZDA 3 WAS STRUCK WHILE PARKED. MONTHS LATER AIR BAG LIGHT CAME ON AND REPEATEDLY WENT TO THE LOCAL MAZDA DEALERSHIP ABOUT THE ISSUE. LAST ENCOUNTER WITH DEALERSHIP(OCT 2014), THEY CHECKED THE AIR BAG AND CONCLUDED IT WAS NOT A RECALL ISSUE, AND STATED THE PROBLEM STEMS FROM AUTO ACCIDENT. COMPLAINED TO MY INSURANCE CO …
Read full complaint
2008 MAZDA 3 WAS STRUCK WHILE PARKED. MONTHS LATER AIR BAG LIGHT CAME ON AND REPEATEDLY WENT TO THE LOCAL MAZDA DEALERSHIP ABOUT THE ISSUE. LAST ENCOUNTER WITH DEALERSHIP(OCT 2014), THEY CHECKED THE AIR BAG AND CONCLUDED IT WAS NOT A RECALL ISSUE, AND STATED THE PROBLEM STEMS FROM AUTO ACCIDENT. COMPLAINED TO MY INSURANCE CO AND RE-OPENED CLAIM. THE INSURANCE COMPANY(NOV 2014) CONCLUDED FROM WHERE THE CAR WAS IMPACTED ON THE REAR PASSENGER SIDE, THE AIR BAG IS NOT THEIR ISSUE AND DID NOT STEM FROM CAUSE OF IMPACT. AIR BAG MODULE NEEDS TO BE INVESTIGATED AND ADDRESSED WITH MAZDA CO. WITH ALL THESE DEVELOPMENTS WITH FAULTY AIR BAGS MADE BY TAKATA(COMPANY WHOM MAKE AIRBAGS), SOMETHING IS TOTALLY WRONG. THIS IS A SAFETY ISSUE, THAT NEEDS TO BE TAKEN CARE OF. *TR
THE TIRE PRESSURE LIGHT CAME ON AS I WAS DRIVING ON THE HIGHWAY. WHEN I STOPPED TO FILL MY TIRES, THE FORCE OF THE AIR HOSE BLEW THE TIRE PRESSURE SENSOR INTO MY TIRE. I HAD TO HAVE THE SENSOR REPLACED, AND WAS TOLD THAT THE OTHER 3 SENSORS WERE CLOSE TO WEARING THROUGH AS WELL. *TR
VIBRATION AT 55-63 MPH. TIRES WEARING ON INSIDE IN DIAGONAL PATTERN ON FRONT. WORN COMPLETELY TO THE CORE. THIRD SET OF TIRES. *TR
FEBRUARY 2014 1ST VALVE STEM AND SENSOR BROKE. THIS WEEK 2ND AND 3RD VALVE STEM AND SENSORS BROKE. $90-100 EACH TO FIX. RUINED ONE TIRE AND CAUSED SUDDEN FLAT WHICH COULD HAVE RESULTED IN ACCIDENT. *TR
TAIL/BRAKE LIGHT LENSES MELTED. ORIGINAL PARTS,REPLACED THE WHOLE TAIL LIGHT ASSEMBLY AND BULBS IN JUNE 2014 AND I NOTICED IN AUGUST 2014 THE TAIL LIGHT ON THE DRIVERS SIDE WAS OUT. THE LENSES MELTED AGAIN, THE BULBS WERE 7443 .RESEARCHED ON THE INTERNET AND FOUND THIS PROBLEM ON NUMEROUS POSTS MAINLY WITH THE MAZDA 3 HATCHBACK …
Read full complaint
TAIL/BRAKE LIGHT LENSES MELTED. ORIGINAL PARTS,REPLACED THE WHOLE TAIL LIGHT ASSEMBLY AND BULBS IN JUNE 2014 AND I NOTICED IN AUGUST 2014 THE TAIL LIGHT ON THE DRIVERS SIDE WAS OUT. THE LENSES MELTED AGAIN, THE BULBS WERE 7443 .RESEARCHED ON THE INTERNET AND FOUND THIS PROBLEM ON NUMEROUS POSTS MAINLY WITH THE MAZDA 3 HATCHBACK WHICH IS WHAT I HAVE. CALLED THE LOCAL MAZDA DEALER AND THEY SAID THEY NEVER HEARD OF THE PROBLEM. SOUNDS LIKE A FIRE HAZARD. HAVE YOU HAD ANY OTHER COMPLAINTS ABOUT THIS? *TR
TIRE PRESSURE SENSOR MODULES HAVE BEEN FAILING REPEATEDLY. NOTHING WRONG WITH THE TIRES, BUT THESE THINGS ARE MADE OF CERAMIC (APPARENTLY), GET FULL OF SALT AND/OR OTHER ROAD DETRITUS, AND THEN FALL APART, CAUSING A FLAT TIRE PLUS ADDITIONAL EXPENSE TO REPLACE THE FANCY THINGS. INSTEAD OF REPORTING A PROBLEM, WHICH IS SUPPOSED…
Read full complaint
TIRE PRESSURE SENSOR MODULES HAVE BEEN FAILING REPEATEDLY. NOTHING WRONG WITH THE TIRES, BUT THESE THINGS ARE MADE OF CERAMIC (APPARENTLY), GET FULL OF SALT AND/OR OTHER ROAD DETRITUS, AND THEN FALL APART, CAUSING A FLAT TIRE PLUS ADDITIONAL EXPENSE TO REPLACE THE FANCY THINGS. INSTEAD OF REPORTING A PROBLEM, WHICH IS SUPPOSEDLY WHAT THEY ARE FOR, THEY ARE THE PROBLEM. I'VE HAD TO REPLACE THREE SO FAR; I'VE TAKEN TO BUYING THEM ONLINE IN MULTIPLES; GOD ONLY KNOWS WHAT A DEALERSHIP WOULD CHARGE ME FOR ONE PLUS THE INSTALLATION. THIS IS GOING TO BE THE RUINATION OF MY VERY NICE TIRES, AS I NEVER KNOW WHEN ONE IS GOING TO FAIL AGAIN, BUT IT'S A LEAD PIPE CERTAINTY THAT THIS IS GOING TO CONTINUE. I'M CONSIDERING SIMPLY REPLACING THEM AS THEY FAIL WITH ORDINARY VALVE STEMS, AND COVERING THE DASHBOARD LIGHT WITH A BIT OF ELECTRICIANS' TAPE. NOT QUITE THE INTENDED OUTCOME, I'M THINKING..... *TR
I WAS DRIVING ON THE HIGHWAY TRAVELING ABOUT 65 MPH WHEN MY TIRE WARNING LIGHT CAME ON, FOLLOWED IMMEDIATELY BY MY FRONT DRIVER'S SIDE TIRE GOING COMPLETELY FLAT. LUCKILY THERE WAS NOBODY TOO CLOSE TO ME, SO THERE WAS NO ACCIDENT WHEN I SWERVED ONTO THE SHOULDER OF THE ROAD. I CHANGED MY TIRE AND MADE IT TO A SERVICE CENTER …
Read full complaint
I WAS DRIVING ON THE HIGHWAY TRAVELING ABOUT 65 MPH WHEN MY TIRE WARNING LIGHT CAME ON, FOLLOWED IMMEDIATELY BY MY FRONT DRIVER'S SIDE TIRE GOING COMPLETELY FLAT. LUCKILY THERE WAS NOBODY TOO CLOSE TO ME, SO THERE WAS NO ACCIDENT WHEN I SWERVED ONTO THE SHOULDER OF THE ROAD. I CHANGED MY TIRE AND MADE IT TO A SERVICE CENTER WHERE I WAS INFORMED THAT IT WAS MY TPMS AND VALVE STEM ASSEMBLY THAT HAD CORRODED AND FAILED, CAUSING MY TIRE TO IMMEDIATELY GO FLAT. NOT ONLY DID I HAVE TO PAY TO INSTALL A NEW TIRE ($300) I HAD TO REPLACE THE DESTROYED TPMS SENSOR AND REPLACE ANOTHER ONE THAT WAS ALSO CORRODING. ($100 EA). THE ENTIRE INCIDENT COST ME ABOUT $500 DUE TO A DESIGN FLAW FROM MAZDA THAT I HAVE NO POWER TO AVOID. THE ISSUE IS THAT IT IS ILLEGAL TO REMOVE OR NOT HAVE THE SENSORS RE-INSTALLED, AS THEY ARE A SAFETY FEATURE. THE IRONY IS THAT I HAVE TO PAY $100 EACH TO INSTALL A COMPONENT THAT CAUSES ONE OF MY TIRES TO IMMEDIATELY DEFLATE RANDOMLY IN THE NEXT 3-5 YEARS, DEPENDING ON WHEN IT CORRODES AGAIN. IT IS INFURIATING THAT I HAVE TO INSTALL A "SAFETY FEATURE" THAT WILL RANDOMLY CAUSE ME TO LOSE CONTROL OVER MY CAR IN THE NEAR FUTURE. AS IT IS RIGHT NOW, I WILL BE FORCED TO DRIVE WITH A COMPONENT THAT, OVER TIME, WILL CORRODE AND FAIL, CAUSING ME TO LOSE CONTROL OF MY CAR, THEN RE-INSTALL THE EXACT FAULTY COMPONENT. THE SENSOR / VALVE ASSEMBLY SHOULD HAVE NEVER BEEN MADE OF A MATERIAL THAT IS SUSCEPTIBLE TO CORROSION IN THE FIRST PLACE. I WAS LUCKY THIS TIME THAT THIS DIDN'T CAUSE AN ACCIDENT, BUT IF THE SITUATION WERE DIFFERENT I COULD HAVE EASILY BEEN KILLED OR HAVE KILLED SOMEONE. THIS IS A SERIOUS ISSUE THAT NEEDS TO BE ADDRESSED. BOTH MAZDA AND THE GOVERNMENT HAVE BEEN AWARE OF THIS ISSUE FOR A LONG TIME NOW. WHAT IS GOING TO HAPPEN WHEN SOMEONE DOES DIE FROM THIS, AND IT COMES OUT THAT THE ISSUE HAS BEEN KNOWN FOR YEARS, BUT NOBODY DID ANYTHING? *TR
MY BOYFRIEND WAS IN A ROLL OVER ACCIDENT WHERE THE AIRBAG SENSORS WERE COMPLETELY RIPPED OFF ALONG WITH THE BUMPER AND THE AIRBAGS DID NOT DEPLOY AND THE SEATBELT DID NOT LOCK UP UNTIL HE CAME TO A STOP. *TR
TPMS VALVE STEM BROKE WHILE CHECKING TIRE PRESSURE. TOOK VEHICLE TO TIRE DEALER AND FOUND THAT 3 TPMS SENSORS HAD CRACKS IN VALVE STEMS. *TR
Official recalls
211V329000 · Visibility:windshield Wiper/washer:motor
Jun 15, 2011
MAZDA IS RECALLING CERTAIN MODEL YEAR 2008-2009 MAZDA3 AND MAZDASPEED3 VEHICLES MANUFACTURED FROM JANUARY 7, 2008, THROUGH NOVEMBER 28, 2008. THE GROUND TERMINAL OF THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN INADVERTENTLY BENT DURING ASSEMBLY. IF THIS CONDITION EXISTS THEN OVER TIME THE ELECTRICAL RESISTANCE OF THE MOTOR CIRCUIT MAY INCREASE UP TO A POINT THAT THE WINDSHIELD WIPERS WOULD NOT WORK.
Consequence & remedy
Consequence: THE LOSS OF WIPER FUNCTION IN ADVERSE WEATHER COULD POTENTIALLY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL INSTALL AN ADDITIONAL GROUND HARNESS ON THE WIPER MOTOR FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE JULY 15, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.