IllustrationAIR BAG LIGHT STAYS ON FOR NO REASON
2008 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2008 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
620–25K
8925–50K
4050–75K
3475–100K
25100–150K
6150K+
256 reports with mileage · 47 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 117 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 41 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Wheels. Review the 33 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
29 crash reports1 fire reports16 injury reports
What owners actually said
303 reportsJULY 11, 2011. 34443 MILES. CONSTANT RUNNING OF ELECTRIC RADIATOR FAN WHEN VEHICLE IS RUNNING CAUSED BY COMPLETE FAILURE OF OEM WATER PUMP. UNIT REPLACED BY ANOTHER OEM WATER PUMP. NOVEMBER 01, 2017. 97841 MILES. COMPLETE FAILURE OF SECOND OEM WATER PUMP. UNIT REPLACED BY A THIRD OEM WATER PUMP.
TL* THE CONTACT OWNS A 2008 MAZDA 3. THE CONTACT STATED THAT THE VEHICLE HESITATED TO START. AFTER A FEW ATTEMPTS, THE VEHICLE STARTED, BUT THERE WAS NO POWER STEERING. THE VEHICLE WAS DRIVEN TO THE CONTACT'S RESIDENCE VERY SLOWLY. THE CONTACT STATED THAT THE VEHICLE WAS REPAIRED IN 2010 BY STAR MAZDA IN GLENDALE, CALIFORNIA FOR…
Read full complaint
TL* THE CONTACT OWNS A 2008 MAZDA 3. THE CONTACT STATED THAT THE VEHICLE HESITATED TO START. AFTER A FEW ATTEMPTS, THE VEHICLE STARTED, BUT THERE WAS NO POWER STEERING. THE VEHICLE WAS DRIVEN TO THE CONTACT'S RESIDENCE VERY SLOWLY. THE CONTACT STATED THAT THE VEHICLE WAS REPAIRED IN 2010 BY STAR MAZDA IN GLENDALE, CALIFORNIA FOR THE SAME FAILURE PER AN UNKNOWN RECALL ISSUED BY THE MANUFACTURER. THE VEHICLE WAS NOT REPAIRED THIS TIME AND THE DEALER WAS NOT CONTACTED AGAIN. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 90,000.
AT LIGHT AND CHECK ENGINE LIGHT COME ON. WHILE DRIVING ON FREEWAY HARD SHIFTS AUTOMATICALLY FROM 5TH GEAR DOWN TO A HARSH 3RD GEAR. CANNOT GET AT LIGHT TO SHUT OFF, REPLACED SOLINOIDS, TCM, PCM AND STILL CANNOT LOCATE THE ISSUE. CAR WILL NOT GO PAST 3RD GEAR. CAR IS STILL UNDER 80K MILES.
I WAS DRIVING AROUND A TURN GOING APPROXIMATELY 25-30 MPH WHEN I LOST CONTROL OF THE CAR. IT IS BELIEVED THAT THE TIRE SUDDENLY LOST AIR PRESSURE AND RAN ME OFF THE ROAD. I WAS LEFT IN THE CREEK WITH MY TWO AND THREE YEAR OLD. TWO GUYS HELPED ME GET THE KIDS AND MYSELF OUT THE CAR SAFELY. MY CAR IS NOW TOTALED DUE TO THE FAILURE…
Read full complaint
I WAS DRIVING AROUND A TURN GOING APPROXIMATELY 25-30 MPH WHEN I LOST CONTROL OF THE CAR. IT IS BELIEVED THAT THE TIRE SUDDENLY LOST AIR PRESSURE AND RAN ME OFF THE ROAD. I WAS LEFT IN THE CREEK WITH MY TWO AND THREE YEAR OLD. TWO GUYS HELPED ME GET THE KIDS AND MYSELF OUT THE CAR SAFELY. MY CAR IS NOW TOTALED DUE TO THE FAILURE OF THE PASSENGER SIDE TIRE. TIRE SIZE WAS 205 55 16. THERE WAS NO PUNCTURE HOLES ON THE TIRE SO NO REAASON FOR THE SUDDEN LOSS OF AIR.
LOST ALL POWER WHILE DRIVING AND TURNING. ABS, BRAKE , PS , BATTERY LIGHTS ON DASH ILLUMINATED, CAR LOOSES STEERING AND THEN THE ENGINE DIES. BATTERY DISCHARGED AS PER LOAD TEST.ALTERNATOR TESTS FINE. HAPPENED TWO TIMES AFTER THE POWER STEERING MANUFACTURER RECALL WAS PERFORMED TO REMEDY THE SAME ISSUE.
THIS IS FOR A 2008.5 MAZDA3. THE ISSUE I AM REPORTING IS WITH A "SOFT PEDAL" CAUSED BY A MALFUNCTION IN THE ABS SYSTEM. THIS PROBLEM BEGAN WHEN DRIVING OVER A BUMP AND SIMULTANEOUSLY PRESSING DOWN ON THE BRAKES. THE BRAKES AND ABS SYSTEM ENGAGE AND CAR SLOWS DOWN. HOWEVER, AFTER THAT, THE PEDAL LOSES PRESSURE AND NEEDS TO BE PUS…
Read full complaint
THIS IS FOR A 2008.5 MAZDA3. THE ISSUE I AM REPORTING IS WITH A "SOFT PEDAL" CAUSED BY A MALFUNCTION IN THE ABS SYSTEM. THIS PROBLEM BEGAN WHEN DRIVING OVER A BUMP AND SIMULTANEOUSLY PRESSING DOWN ON THE BRAKES. THE BRAKES AND ABS SYSTEM ENGAGE AND CAR SLOWS DOWN. HOWEVER, AFTER THAT, THE PEDAL LOSES PRESSURE AND NEEDS TO BE PUSHED ALL THE WAY DOWN TO THE FLOOR IN ORDER TO GET THE CAR TO STOP. THIS ISSUE CAN BE FIXED BY ACTIVATING THE ABS SYSTEM AGAIN AND COMING TO A COMPLETE STOP. HOWEVER, WHEN BRAKING OVER A BUMP AGAIN THE ISSUE CONTINUES TO HAPPEN. IT LOOKS LIKE THIS ISSUE HAS RECENTLY STARTED TO BECOME WIDELY REPORTED FOR MAZDA3, MAZDA6, AND FORD FUSIONS. I AM SEEING THAT THERE IS AN INVESTIGATION OPENED IN DECEMBER 2016 FOR THE FORD FUSION AND THE MERCURY MILAN. I WOULD LIKE TO REPORT THAT THIS DEFECT IS ALSO EVIDENT IN MAZDA'S AS WELL. THERE IS A LOT OF CONFUSION AS TO WHAT IS CAUSING THIS PROBLEM AND IT SEEMS MOST PEOPLE GO AND REPLACE THEIR MASTER CYLINDER, CALIPERS, BRAKE PADS, ECT. IN ORDER TO FIX THE PROBLEM. THE PROBLEM LOOKS TO BE WITH THE HYDRAULIC'S IN THE ABS SYSTEM.
TAKATA RECALL 1 VEHICLE CRASH WHERE VEHICLE HYDROPLANED ON INTERSTATE CRASHING INTO RETAINING WALL WITH FRONT END DAMAGE AND NO AIR BAG DEPLOYMENT.
AEVERAL RECALLS FOR 2008 MAZDA3..... HOWEVER MY VIN ISNT ASSOSIATED WITH ANY AND I HAVE ALL THE PROBLEMA. POWER STEERINGS UNIT STRIPPED2 OR THE 3 BOLTS HOLES ANS FELL DOWN FROM CRACKED ENGINE MOUNTS SLIGHT RATTLING..... STATIONARY AND MOVING. IDLE IS AT 500-1,000 RPMS VERY ODD FEELING. RANDOM BODY DAMAGE AND ENTIRE OF BOTTOM EN…
Read full complaint
AEVERAL RECALLS FOR 2008 MAZDA3..... HOWEVER MY VIN ISNT ASSOSIATED WITH ANY AND I HAVE ALL THE PROBLEMA. POWER STEERINGS UNIT STRIPPED2 OR THE 3 BOLTS HOLES ANS FELL DOWN FROM CRACKED ENGINE MOUNTS SLIGHT RATTLING..... STATIONARY AND MOVING. IDLE IS AT 500-1,000 RPMS VERY ODD FEELING. RANDOM BODY DAMAGE AND ENTIRE OF BOTTOM ENGINE RUSTY.... PAINT RUSTS AS WELL. JUST BOUGHT THE CAR ON FINANCE AND REALLY NEED SOME HELP
I WAS DRIVING ON THE TOLLWAY TO WORK YESTERDAY MORNING, 3/24/2017, I LIGHTLY TAPPED MY BREAKS, AND MY MAZDA 3 JUMPED, HARD BREAKING SENSATION, AND MADE ME SWERVE DUE TO THE CAR MALFUNCTIONING. THE AUTOMATIC TRANSMISSION LIGHT ILLUMINATED AND WENT OFF. YESTERDAY EVENING, I STARTED MY MAZDA 3 TO REVERSE OUT OF A PARKING LOT AND B…
Read full complaint
I WAS DRIVING ON THE TOLLWAY TO WORK YESTERDAY MORNING, 3/24/2017, I LIGHTLY TAPPED MY BREAKS, AND MY MAZDA 3 JUMPED, HARD BREAKING SENSATION, AND MADE ME SWERVE DUE TO THE CAR MALFUNCTIONING. THE AUTOMATIC TRANSMISSION LIGHT ILLUMINATED AND WENT OFF. YESTERDAY EVENING, I STARTED MY MAZDA 3 TO REVERSE OUT OF A PARKING LOT AND BOTH THE CHECK ENGINE LIGHT AND THE AUTOMATIC TRANSMISSION LIGHT IMMEDIATELY ILLUMINATED AND NEVER WENT OFF. THE GEAR LIGHTS WOULD NOT ILLUMINATE ON MY PANEL. MY MAZDA 3 WOULD REVERSE, BUT IT TOOK A FEW MINUTES TO GET THE CAR TO GO INTO DRIVE. I TOOK MY CAR TO A MECHANIC FIRST THING THIS MORNING, 3/25/2017, AND THE TRANSMISSION NEEDS TO BE REPLACED. WITH NO WARNING AND NO PREVIOUS TRANSMISSION PROBLEMS, ALL THE ELECTRICAL COMPONENTS OF THE TRANSMISSION ARE GONE AND THE TRANSMISSION HAS FAILED. ADDITIONALLY, I TOOK MY CAR TO THE DEALERSHIP ON 3/14/2017, AND NO ONE IN THE SERVICE DEPARTMENT SAID MY TRANSMISSION WAS IN BAD SHAPE OR ABOUT TO COMPLETELY FAIL. I AM NOT THE ONLY MAZDA OWNER WITH THIS PROBLEM, IT SEEMS TO BE A VERY COMMON THEME WITH MAZDAS. MY CAR HAS 88,578 MILES ON IT.
Official recalls
211V329000 · Visibility:windshield Wiper/washer:motor
Jun 15, 2011
MAZDA IS RECALLING CERTAIN MODEL YEAR 2008-2009 MAZDA3 AND MAZDASPEED3 VEHICLES MANUFACTURED FROM JANUARY 7, 2008, THROUGH NOVEMBER 28, 2008. THE GROUND TERMINAL OF THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN INADVERTENTLY BENT DURING ASSEMBLY. IF THIS CONDITION EXISTS THEN OVER TIME THE ELECTRICAL RESISTANCE OF THE MOTOR CIRCUIT MAY INCREASE UP TO A POINT THAT THE WINDSHIELD WIPERS WOULD NOT WORK.
Consequence & remedy
Consequence: THE LOSS OF WIPER FUNCTION IN ADVERSE WEATHER COULD POTENTIALLY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL INSTALL AN ADDITIONAL GROUND HARNESS ON THE WIPER MOTOR FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE JULY 15, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.