IllustrationBRAKE ROTORS WARP EARLY ON 2008 MAZDA 3 CAUSING EXCESSIVE VIBRATION WHEN BRAKING OVER 45 MPH AND CAUSES THE STEERING WHEEL TO SHAKE. *TR
2008 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2008 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
620–25K
8925–50K
4050–75K
3475–100K
25100–150K
6150K+
256 reports with mileage · 47 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 117 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 41 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Wheels. Review the 33 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
29 crash reports1 fire reports16 injury reports
What owners actually said
303 reportsAT 71,XXX MILES 2 OUT OF 4 THE TIRE PRESSURE MONITOR SENSOR VALVE STEMS HAVE FAILED. THE VALVE STEM CAPS WERE OEM GRAY PLASTIC CAPS. ALL PARTS OF THIS SYSTEM ON THIS CAR ARE OEM. THE VALVE STEMS CORRODE BELOW WHERE THE SCHRADER VALVE SEAL SO THE TIRES GOES FLAT IN JUST A FEW SECONDS.
I OWN A 2008 MAZDA 3 AND LIKE OTHERS, I AM HAVING ISSUES WITH THE WIPERS NOT WORKING WHEN THE WEATHER IS BAD!! DURING A SNOW STORM AFTER TRAVELING SOME DISTANCE, THE WIPERS DECIDED NOT TO WORK. THEY JUST STOPPED. THEY WOULDN'T STAY RUNNING, SO I HAD TO LEAVE THE CAR IN A PARKING LOT AND HAVE SOMEONE DRIVE TO PICK ME UP AN HO…
Read full complaint
I OWN A 2008 MAZDA 3 AND LIKE OTHERS, I AM HAVING ISSUES WITH THE WIPERS NOT WORKING WHEN THE WEATHER IS BAD!! DURING A SNOW STORM AFTER TRAVELING SOME DISTANCE, THE WIPERS DECIDED NOT TO WORK. THEY JUST STOPPED. THEY WOULDN'T STAY RUNNING, SO I HAD TO LEAVE THE CAR IN A PARKING LOT AND HAVE SOMEONE DRIVE TO PICK ME UP AN HOUR AWAY. HAD IT CHECKED AT MAZDA AND OF COURSE THEY WORKED THAT DAY. THEY HAVE SINCE STARTED TO ACT UP AGAIN, AGAIN ON A LONGER TRIP AND DURING A THUNDERSTORM. LUCKILY I WAS ABLE TO PULL OVER ON THIS 5 LANE HIGHWAY BEFORE GETTING KILLED!! I COULD NOT SEE ANYTHING DURING THE RAIN. THIS NEEDS TO BE FIXED. I HAVE YET TO CALL MAZDA I AM UNDER WARRANTY AND HOPEFULLY THEN THIS WILL BE COVERED AND THEY WON'T HAVE SOME EXCUSE WHY IT ISN'T COVERED! *TR
OWN A 2008 MAZDA 3. PURCHASED USED, BUT WAS SOLD NEW AND SERVICED LOCALLY TO ORIGINAL OWNER. TPMS INDICATED LOW TIRE. WHEN TRIED TO PUT AIR IN THE TIRE, VALVE AND SENSOR BROKE/CORRODED AND ALL THE AIR CAME OUT OF TIRE. FLATBEDDED TO DEALERSHIP OUT OF TOWN WHERE I WAS LOCATED.. NEW VALVE INSTALLED AND TIRE FIXED . PART WAS $…
Read full complaint
OWN A 2008 MAZDA 3. PURCHASED USED, BUT WAS SOLD NEW AND SERVICED LOCALLY TO ORIGINAL OWNER. TPMS INDICATED LOW TIRE. WHEN TRIED TO PUT AIR IN THE TIRE, VALVE AND SENSOR BROKE/CORRODED AND ALL THE AIR CAME OUT OF TIRE. FLATBEDDED TO DEALERSHIP OUT OF TOWN WHERE I WAS LOCATED.. NEW VALVE INSTALLED AND TIRE FIXED . PART WAS $120 FOR VALVE SENSOR PIECE. CALLED MY LOCAL MAZDA PLACE TO SEE IF THIS COULD POSSIBLY BE RIGHT FOR SUCH A SMALL PIECE AND TO SEE IF IT SHOULD BE UNDER WARRANTY. THEY CONFIRMED NO WARRANTY AND AVERAGE PRICE. NOW A SECOND TIRE INDICATED LOW, AND TRIED TO CHECK PRESSURE AND AS SOON AS THE TIRE VALVE CAP WAS TURNED AND REMOVED STEM/SENSOR BROKE AGAIN IN THIS DIFFERENT TIRE AND NOW HAS LOST AIR . NOW NEEDS REPLACING. AFRAID THIS WILL BE THE SAME ISSUE FOR THE REMAINING 2 TIRES. NEED TO STILL GET SNOWS OFF, BUT DON'T WANT TO PAY FOR THE STEM/SENSORS AT $120 A PIECE! HAVE READ NUMEROUS COMPLAINTS ONLINE OF THIS ISSUE!! A RECALL NEEDS TO BE DONE ... THIS IS UNSAFE IF IT HAPPENS WHEN DRIVING AS MANY HAVE MENTIONED!! MAZDA DEALERS TOLD ME I MUST HAVE HIT A CURB OR FROM POTHOLES IN THE WINTER. THIS IS NOT THE CASE... NOT FOR ALL 4 TO HAVE THIS HAPPEN. *TR
TIRE VALVE STEM CORROSION ON 2008 MAZDA 3. ON 5/27/2011 TPMS INDICATOR CAME ON WHILE DRIVING ON THE HIGHWAY. I PULLED INTO A GAS STATION AND ATTEMPTED TO PUT AIR INTO THE FRONT DRIVER SIDE TIRE THAT WAS FLAT AND THE STEM VALVE WENT INTO THE TIRE. AFTER SEEING THAT, I CHECKED THE REMAINING VALVES AND ALL ARE CORRODED. THE FRONT…
Read full complaint
TIRE VALVE STEM CORROSION ON 2008 MAZDA 3. ON 5/27/2011 TPMS INDICATOR CAME ON WHILE DRIVING ON THE HIGHWAY. I PULLED INTO A GAS STATION AND ATTEMPTED TO PUT AIR INTO THE FRONT DRIVER SIDE TIRE THAT WAS FLAT AND THE STEM VALVE WENT INTO THE TIRE. AFTER SEEING THAT, I CHECKED THE REMAINING VALVES AND ALL ARE CORRODED. THE FRONT PASSENGER TIRE VALVE IS ABOUT TO GO INTO THE TIRE AND THE BACK TIRES VALVES ARE CRACKED. I NOW HAVE TO HAVE MY CAR PUT ON A FLAT BED BECAUSE MY HALF SPARE IS ON THE FRONT DRIVER SIDE AND TO AVOID AN ACCIDENT AND NOT HAVING ANOTHER SPARE TIRE, THIS CAR IS NOW A DEATH TRAP AND IS VERY UNSAFE. I ALSO NOTICED THAT OTHER OWNERS HAVE FILED COMPLAINTS ONLINE WITH WWW.ABOUTAUTOMOBILE.COM WITH THE SAME PROBLEM WITH THE SAME YEAR AND MAKE. THIS NEEDS TO BE INVESTIGATED AS MY OTHER TIRES COULD GO FLAT AT ANYTIME NOW WHICH MAKES IT A HAZARD TO MYSELF AND OTHERS. *TR
WIPER MOTOR FAILURE, 2008 MAZDA 3 GRAND TOURING. WIPERS WORKING FINE AND IN A HEAVY STORM THEY DECIDED TO QUIT. I AM AWARE THAT THIS IS AN ELECTRICAL PART AND CAN FAIL AT ANY TIME, BUT I HAVE NOTICED THIS IS AN RECURRING PROBLEM FOR MAZDA. THIS NEEDS TO ADDRESSED BEFORE SOMEONE GETS HURT OR LOSES THEIR LIFE OVER SOMETHING THAT C…
Read full complaint
WIPER MOTOR FAILURE, 2008 MAZDA 3 GRAND TOURING. WIPERS WORKING FINE AND IN A HEAVY STORM THEY DECIDED TO QUIT. I AM AWARE THAT THIS IS AN ELECTRICAL PART AND CAN FAIL AT ANY TIME, BUT I HAVE NOTICED THIS IS AN RECURRING PROBLEM FOR MAZDA. THIS NEEDS TO ADDRESSED BEFORE SOMEONE GETS HURT OR LOSES THEIR LIFE OVER SOMETHING THAT CAN BE CORRECTED. *TR
ON 4/19/2011 I WAS DRIVING WHEN MY TPMS WENT OFF. I PULLED INTO A GAS STATION TO PUT AIR IN MY TIRE. AS I PUT THE AIR PUMP TO THE VALVE, THE VALVE SIMPLY DISAPPEARED AND THE TIRE WENT COMPLETELY FLAT. I CALLED AAA AND TOOK THE CAR TO A REPAIR SHOP. THEY SAID THE TIRE WAS PERFECTLY FINE AND REPLACED IT (WITHOUT THE TPMS). I …
Read full complaint
ON 4/19/2011 I WAS DRIVING WHEN MY TPMS WENT OFF. I PULLED INTO A GAS STATION TO PUT AIR IN MY TIRE. AS I PUT THE AIR PUMP TO THE VALVE, THE VALVE SIMPLY DISAPPEARED AND THE TIRE WENT COMPLETELY FLAT. I CALLED AAA AND TOOK THE CAR TO A REPAIR SHOP. THEY SAID THE TIRE WAS PERFECTLY FINE AND REPLACED IT (WITHOUT THE TPMS). I EVENTUALLY REPLACED THE TPMS, WHICH WAS NOT COVERED UNDER WARRANTY. ON 4/25/2011, I WAS DRIVING ON THE HIGHWAY WHEN THE TPMS WENT OFF AGAIN. THIS TIME ANOTHER TIRE HAD GONE COMPLETELY FLAT. WHEN AAA ARRIVED, THE SERVICEMAN FOUND THE BROKEN PARTS OF THE PIECE THAT HOLDS THE VALVE STEM (AND THE TPMS) IN THE WHEEL. WITHOUT THIS PIECE, THE VALVE WAS ABLE TO SLIP INTO THE WHEEL (WHICH IS WHAT HAD HAPPENED TO ME ON 4/19). THE PIECES WERE COMPLETELY CORRODED AND HAD CRACKED IN 3 PLACES. THE DEALER REPLACED THE TPMS (WHICH WAS NOT, AGAIN, COVERED UNDER WARRANTY). ONLY AFTER I INSISTED DID THEY REPLACE THE REMAINING TWO VALVE STEMS WHICH ALSO HAD CLEAR SIGNS OF CRACKING. THIS WILL MOST LIKELY HAPPEN AGAIN IN THE FUTURE AS THE TWO METALS OF THE VALVE STEM AND THE PIECE HOLDING IT ON BEGIN TO CORRODE. UPDATED IVOQ 06/28/11 *TR
2008 MAZDA 3 S GRAND TOURING - FRONT WINDSHIELD WIPERS JUST STOPPED WORKING. THIS HAPPENED DURING A RAINSTORM. I CHECKED THE FUSES AND ALL LOOKED GOOD. AFTER SPENDING MUCH TIME ONLINE, IT APPEARS THAT MANY PEOPLE HAVE HAD A SIMILAR PROBLEM. *TR
TL*THE CONTACT OWNS A 2008 MAZDA, MAZDA3. THE CONTACT WAS INVOLVED IN A CRASH WHEN SOMEONE RAN THEM OFF THE ROAD AND CAUSED THE VEHICLE TO ROLL OVER AND GO INTO THE BOTTOM OF A RAVINE. THE CONTACT WAS NOT INJURED, BUT WAS CONCERNED SINCE THE AIR BAGS DID NOT DEPLOY. THE VEHICLE WAS DESTROYED. THE CONTACT STATED THE VEHICLE WAS N…
Read full complaint
TL*THE CONTACT OWNS A 2008 MAZDA, MAZDA3. THE CONTACT WAS INVOLVED IN A CRASH WHEN SOMEONE RAN THEM OFF THE ROAD AND CAUSED THE VEHICLE TO ROLL OVER AND GO INTO THE BOTTOM OF A RAVINE. THE CONTACT WAS NOT INJURED, BUT WAS CONCERNED SINCE THE AIR BAGS DID NOT DEPLOY. THE VEHICLE WAS DESTROYED. THE CONTACT STATED THE VEHICLE WAS NOT INSPECTED TO SEE WHY THE AIR BAGS DID NOT DEPLOY. THE FAILURE MILEAGE WAS 55,000.
TL*THE CONTACT OWNS A 2008 MAZDA 3. THE CONTACT STATED THAT AFTER RECEIVING TWO RECALL NOTICES IN REGARDS TO NHTSA CAMPAIGN ID NUMBER 10V374000(STEERING:ELECTRIC POWER ASSIST SYSTEM). SINCE AUGUST OF LAST YEAR SHE TRIED TO CONTACT THE DEALER AND SCHEDULE AN APPOINTMENT, BUT THEY CONTINUED TO ADVISE HER THAT THE PARTS WERE UNAVAI…
Read full complaint
TL*THE CONTACT OWNS A 2008 MAZDA 3. THE CONTACT STATED THAT AFTER RECEIVING TWO RECALL NOTICES IN REGARDS TO NHTSA CAMPAIGN ID NUMBER 10V374000(STEERING:ELECTRIC POWER ASSIST SYSTEM). SINCE AUGUST OF LAST YEAR SHE TRIED TO CONTACT THE DEALER AND SCHEDULE AN APPOINTMENT, BUT THEY CONTINUED TO ADVISE HER THAT THE PARTS WERE UNAVAILABLE. THE VEHICLE WAS NOT REPAIRED NOR HAD THE MANUFACTURER BEEN CONTACTED. THE FAILURE MILEAGE WAS UNKNOWN. UPDATED 06/01/11*LJ UPDATED 06/13/11
Official recalls
211V329000 · Visibility:windshield Wiper/washer:motor
Jun 15, 2011
MAZDA IS RECALLING CERTAIN MODEL YEAR 2008-2009 MAZDA3 AND MAZDASPEED3 VEHICLES MANUFACTURED FROM JANUARY 7, 2008, THROUGH NOVEMBER 28, 2008. THE GROUND TERMINAL OF THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN INADVERTENTLY BENT DURING ASSEMBLY. IF THIS CONDITION EXISTS THEN OVER TIME THE ELECTRICAL RESISTANCE OF THE MOTOR CIRCUIT MAY INCREASE UP TO A POINT THAT THE WINDSHIELD WIPERS WOULD NOT WORK.
Consequence & remedy
Consequence: THE LOSS OF WIPER FUNCTION IN ADVERSE WEATHER COULD POTENTIALLY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL INSTALL AN ADDITIONAL GROUND HARNESS ON THE WIPER MOTOR FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE JULY 15, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.