IllustrationMY BOYFRIEND WAS IN A ROLL OVER ACCIDENT WHERE THE AIRBAG SENSORS WERE COMPLETELY RIPPED OFF ALONG WITH THE BUMPER AND THE AIRBAGS DID NOT DEPLOY AND THE SEATBELT DID NOT LOCK UP UNTIL HE CAME TO A STOP. *TR
2008 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2008 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
620–25K
8925–50K
4050–75K
3475–100K
25100–150K
6150K+
256 reports with mileage · 47 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 117 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 41 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Wheels. Review the 33 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
29 crash reports1 fire reports16 injury reports
Seat Belts complaints
4 reportsTL*THE CONTACT OWNS A 2008 MAZDA, MAZDA3. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 55 MPH, THE VEHICLE HIT A WASHBOARD AND ROLLED DOWN A HILL. THE AIR BAGS DID NOT DEPLOY AND THE SEAT BELTS LOOSENED. THE CONTACT SUSTAINED NECK AND BACK INJURIES. A POLICE REPORT WAS FILED. THE VIN WAS UNAVAILABLE. THE FAILURE MILEAGE W…
Read full complaint
TL*THE CONTACT OWNS A 2008 MAZDA, MAZDA3. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 55 MPH, THE VEHICLE HIT A WASHBOARD AND ROLLED DOWN A HILL. THE AIR BAGS DID NOT DEPLOY AND THE SEAT BELTS LOOSENED. THE CONTACT SUSTAINED NECK AND BACK INJURIES. A POLICE REPORT WAS FILED. THE VIN WAS UNAVAILABLE. THE FAILURE MILEAGE WAS APPROXIMATELY 40,000.
I WAS INVOLVED IN A FOUR CAR COLLISION. I WAS THIRD IN LINE, AND WAS HIT REALLY HARD FROM BEHIND AND THEN HIT THE CAR IN FRONT OF ME. MY AIR BAGS DID NOT DEPLOY AND MY SEAT BELT DID NOT LOCK. I SLAMMED INTO THE STEERING WHEEL AND BUSTED MY FOREHEAD OPEN. *TR
THE WARNING CHIME FOR SEAT BELTS NOT BEING USED IS INAUDIBLE ON THE 2008 MAZDA3 EVEN WITH ALL ACCESSORIES TURNED OFF. THE DEALER EXPLAINED THAT THEY WERE CHANGED DUE TO CUSTOMER COMPLAINTS THAT PREVIOUS YEARS WERE TOO LOUD AND PERSISTENT. THIS IS A VERY SERIOUS SAFETY ISSUE AND THE DEALER CHECKED IT OUT AND DECLARED "THAT'S TH…
Read full complaint
THE WARNING CHIME FOR SEAT BELTS NOT BEING USED IS INAUDIBLE ON THE 2008 MAZDA3 EVEN WITH ALL ACCESSORIES TURNED OFF. THE DEALER EXPLAINED THAT THEY WERE CHANGED DUE TO CUSTOMER COMPLAINTS THAT PREVIOUS YEARS WERE TOO LOUD AND PERSISTENT. THIS IS A VERY SERIOUS SAFETY ISSUE AND THE DEALER CHECKED IT OUT AND DECLARED "THAT'S THE WAY THEY ARE". *TR
Official recalls
211V329000 · Visibility:windshield Wiper/washer:motor
Jun 15, 2011
MAZDA IS RECALLING CERTAIN MODEL YEAR 2008-2009 MAZDA3 AND MAZDASPEED3 VEHICLES MANUFACTURED FROM JANUARY 7, 2008, THROUGH NOVEMBER 28, 2008. THE GROUND TERMINAL OF THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN INADVERTENTLY BENT DURING ASSEMBLY. IF THIS CONDITION EXISTS THEN OVER TIME THE ELECTRICAL RESISTANCE OF THE MOTOR CIRCUIT MAY INCREASE UP TO A POINT THAT THE WINDSHIELD WIPERS WOULD NOT WORK.
Consequence & remedy
Consequence: THE LOSS OF WIPER FUNCTION IN ADVERSE WEATHER COULD POTENTIALLY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL INSTALL AN ADDITIONAL GROUND HARNESS ON THE WIPER MOTOR FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE JULY 15, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.