IllustrationThe brake light bulb has melted and burnt out the brake light housing assembly multiple times, I have purchased multiple brake light housing assembly and the issue continues. Clearly this is a manufacturing defect that is a safety/fire hazard.
2007 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2007 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
270–25K
3325–50K
3250–75K
3475–100K
39100–150K
18150K+
183 reports with mileage · 39 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 89 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 36 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
28 crash reports3 fire reports16 injury reports
What owners actually said
222 reportsAfter a hard brake event to avoid a crash, brake pedal is soft and loses pressure. Identical to many, many Ford and Mitsubishi reports on models that use the same ABS equipment. ABS valves probably leaking internally. Dealer refuses to remedy and insists brakes are fine - they are not, significantly worse since hard brake incide…
Read full complaint
After a hard brake event to avoid a crash, brake pedal is soft and loses pressure. Identical to many, many Ford and Mitsubishi reports on models that use the same ABS equipment. ABS valves probably leaking internally. Dealer refuses to remedy and insists brakes are fine - they are not, significantly worse since hard brake incident. OEM ABS part no longer available (I wonder why?) so the only repair option is a used part that is probably also defective in manufacture.
The contact owns a 2007 Mazda Mazda3. The contact stated their daughter was driving at 15 mph, when making a right turn the steering wheel locked up causing the driver to hit a curb and crash the vehicle into a mailbox. There were no warning lights illuminated on the vehicle, however, the driver stated there was a beeping noise…
Read full complaint
The contact owns a 2007 Mazda Mazda3. The contact stated their daughter was driving at 15 mph, when making a right turn the steering wheel locked up causing the driver to hit a curb and crash the vehicle into a mailbox. There were no warning lights illuminated on the vehicle, however, the driver stated there was a beeping noise coming from the vehicle once the steering wheel locked up. There was no one injured. There was no medical treatment at the scene. A police report was filed. There was damage where the front bumper of the vehicle came off and the front passenger side. The vehicle was towed to a tow yard. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was approximate 101,000.
I WAS DRIVING AND MY POWER STEERING WENT OUT. AS I WAS GOING AROUND A TURN GETTING IT HOME IT STARTED WORKING AGAIN. AFTER THAT MY POWER STEERING WOULD COME AND GO WHILE DRIVING UNTIL IT STOPPED WORKING ALL TOGETHER AFTER A FEW MONTHS OF INTERMITTENT MALFUNCTION. I WAS IN MOTION WHILE IT STOPPED WORKING AND RANDOMLY STARTED WORK…
Read full complaint
I WAS DRIVING AND MY POWER STEERING WENT OUT. AS I WAS GOING AROUND A TURN GETTING IT HOME IT STARTED WORKING AGAIN. AFTER THAT MY POWER STEERING WOULD COME AND GO WHILE DRIVING UNTIL IT STOPPED WORKING ALL TOGETHER AFTER A FEW MONTHS OF INTERMITTENT MALFUNCTION. I WAS IN MOTION WHILE IT STOPPED WORKING AND RANDOMLY STARTED WORKING AGAIN. SEVERAL TIMES.
I RECENTLY PURCHASED THIS VEHICLE USED WITH SALVAGE TITLE ON FEBRUARY 6, 2021. I TOOK IT TO BE INSPECTED AND I NEEDED BOTH BELTS REPLACED, THEY HAD TO TIGHTEN BACK DOWN MY STRUTS IN FRONT, MY POWER STEERING WAS ACTING FUNNY AND MAKING NOISE AND MY INTERMEDIATE SPEED SHAFT SENSOR IS GOING BAD BECAUSE THE CHECK ENGINE LIGHT KEEPS …
Read full complaint
I RECENTLY PURCHASED THIS VEHICLE USED WITH SALVAGE TITLE ON FEBRUARY 6, 2021. I TOOK IT TO BE INSPECTED AND I NEEDED BOTH BELTS REPLACED, THEY HAD TO TIGHTEN BACK DOWN MY STRUTS IN FRONT, MY POWER STEERING WAS ACTING FUNNY AND MAKING NOISE AND MY INTERMEDIATE SPEED SHAFT SENSOR IS GOING BAD BECAUSE THE CHECK ENGINE LIGHT KEEPS COMING BACK ON FOR THE SAME CODE. THERE WAS DAMAGE TO THE VEHICLE BUT THEY DIDN'T TELL ME THAT IT WAS SERIOUS DAMAGE. WHEN DRIVING BARELY TURNING THE WHEEL THE CAR MAKES A WHINING NOISE, THE VEHICLE STILL SWAYS A LITTLE TO THE LEFT AND RIGHT BUT THE ALIGNMENT WAS JUST DONE YESTERDAY. BEFORE I WAS ABLE TO PAY FOR THE ALIGNMENT ETC NEW TIRES AND MOUNT AND BALANCE MY CAR AND STEERING WHEEL WERE BOTH SHAKING REALLY BADLY AND JERKING ALL OVER THE PLACE.
MY VEHICLE STARTED SHAKING ON FRIDAY. I PARKED IT, LATER STARTED IT AND STARTED TO MOVE. HEARD A CRASH. MY TRANSMISSION AND ENGINE FELL. MOTOR MOUNTS BROKEN, DAMAGED MY AXLE.
POWER STEERING QUITS WORKING WHILE DRIVING .POWER STEERING LIGHT COMES ON THE DASH TO WHEN THIS HAPPENS. THIS MAKE STEERING SUPER HARD TO TURNING WHILE DRIVING AND COULD CAUSE AN ACCIDENT BECAUSE ITS UNEXPECTED.
WHILE DRIVING MY VEHICLE AT LEAST 3 TIMES THE POWER STEERING GOES OUT AND MAKES THE CAR UNABLE TO DRIVE AND IS VERY SCARY WHILE ON THE ROAD. A FEW LIGHT INDICATES FLASH ON MY DASH AND THE RADIO RESETS. I EVEN SAW MY RADIO RESET IN BETWEEN THE MAJOR EPISODES WHILE DRIVING 65 MPH. I WAS TRAVELING AT THE 3 TIMES IT HAPPENED ROUGHLY…
Read full complaint
WHILE DRIVING MY VEHICLE AT LEAST 3 TIMES THE POWER STEERING GOES OUT AND MAKES THE CAR UNABLE TO DRIVE AND IS VERY SCARY WHILE ON THE ROAD. A FEW LIGHT INDICATES FLASH ON MY DASH AND THE RADIO RESETS. I EVEN SAW MY RADIO RESET IN BETWEEN THE MAJOR EPISODES WHILE DRIVING 65 MPH. I WAS TRAVELING AT THE 3 TIMES IT HAPPENED ROUGHLY 25-30 MPH AND WAS TURNING THE VEHICLE. I LOCATED A RECALL I BELIEVE # 6010H FOR STEERING: ELECTRIC POWER ASSIST SYSTEM, BUT IT IS FOR VEHICLES MANUFACTURED AFTER APRIL 2, 2017. MY CAR WAS ASSEMBLED ON NOVEMBER 7, 2006. IT STATES THE POWER STEERING PUMP AND LINES NEED TO BE REPLACED. I CANNOT UNDERSTAND WHY MY CAR MANUFACTURED 5 MONTHS PRIOR TO THE RECALL IS NOT COVERED AS THIS COULD CAUSE A SEVERE ACCIDENT WHERE I DO NOT FEEL SAFE DRIVING WITH MY KID IN THE CAR. PLEASE UPDATE THE RANGE OF THE RECALL TO SAVE MORE LIVES.
MY 17YO DAUGHTER WAS DRIVING HER 2007 MAZDA3 WHEN HER POWER STEERING LIGHT CAME ON AND SHE EXPERIENCED A COMPLETE LOSS OF POWER STEERING. SHE WAS TAKEN BY SURPRISE BUT WAS ABLE TO MANEUVER TO SAFETY OFF THE ROAD. SHE RESTARTED THE CAR AND HAD STEERING FOR LESS THAN A MINUTE. I FOUND THE RECALL FOR THIS MODEL AND YEAR, WITH THE…
Read full complaint
MY 17YO DAUGHTER WAS DRIVING HER 2007 MAZDA3 WHEN HER POWER STEERING LIGHT CAME ON AND SHE EXPERIENCED A COMPLETE LOSS OF POWER STEERING. SHE WAS TAKEN BY SURPRISE BUT WAS ABLE TO MANEUVER TO SAFETY OFF THE ROAD. SHE RESTARTED THE CAR AND HAD STEERING FOR LESS THAN A MINUTE. I FOUND THE RECALL FOR THIS MODEL AND YEAR, WITH THESE EXACT SYMPTOMS, BUT FOR SOME REASON IT IS NOT APPLICABLE TO THIS VIN. MAZDA CORP ACKNOWLEDGED THE RECALL BUT SAID SINCE THE NHTSA DIDN'T INCLUDE THIS VIN THERE WAS NOTHING THEY COULD DO. JUDGING BY THE NUMBER OF SIMILAR COMPLAINTS I THINK THE NHTSA SHOULD RECONSIDER EXPANDING THE SCOPE.
SUDDEN LOSS OF POWER STEERING WHILE DRIVING. VEHICLE HAS 70,000 MILES. THERE IS A RECALL FOR THIS YEAR AND MODEL OF VEHICLE FOR THIS EXACT ISSUE, BUT MY VIN WAS NOT ON THE LIST. THE RECALL SHOULD BE WIDENED TO INCLUDE MORE VEHICLES THAT ARE HAVING THIS ISSUE.
Official recalls
221V494000 · Air Bags:frontal
Jul 1, 2021
Mazda North American Operations (Mazda) is recalling certain 2004-2007 Mazda3 vehicles. During air bag deployment, the plastic emblem on the steering wheel air bag module cover may shatter, and project plastic fragments into the vehicle.
Consequence & remedy
Consequence: Plastic fragments can hit occupants during air bag deployment, increasing the risk of injury.
Remedy: Dealers will replace the air bag module cover, free of charge. Owner letters were mailed between August 28, 2021 and October 28, 2021. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 4921G.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.