IllustrationRED AIR BAG LIGHT ON. *TR
2007 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2007 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
270–25K
3325–50K
3250–75K
3475–100K
39100–150K
18150K+
183 reports with mileage · 39 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 89 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 36 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
28 crash reports3 fire reports16 injury reports
What owners actually said
222 reportsCLUNKING NOISE IN TRUNK WHEN GOING OVER RAILROAD TRACKS/BUMPS, ETC.; TOOK TO MAZDA DEALER. PASSENGER SIDE REAR STABILIZER/SWAYBAR BOLT LOOSE AND PIN BENT. KNOWN ISSUE FOR A LOT OF 2007 MAZDAS. NEW BUSHINGS AND BOLTS PUT IN/TIGHTENED. CLUNKING NOISE GONE. *JS
THE BRAKE LIGHT HOUSING (AMBER LENS) WAS HEATED BY THE BULB TO SUCH A DEGREE THAT THE LENS ITSELF MELTED ONTO THE BULB. WE ARE NOT ENTIRELY SURE WHEN THIS HAPPENED AND MAY HAVE BEEN ONGOING FOR QUITE SOME TIME. UPON INSPECTION BY AN EXPERIENCED AUTOMOTIVE TECHNICIAN, IT WAS CONFIRMED THAT THE BULBS WERE THE CORRECT MODEL AND HAD…
Read full complaint
THE BRAKE LIGHT HOUSING (AMBER LENS) WAS HEATED BY THE BULB TO SUCH A DEGREE THAT THE LENS ITSELF MELTED ONTO THE BULB. WE ARE NOT ENTIRELY SURE WHEN THIS HAPPENED AND MAY HAVE BEEN ONGOING FOR QUITE SOME TIME. UPON INSPECTION BY AN EXPERIENCED AUTOMOTIVE TECHNICIAN, IT WAS CONFIRMED THAT THE BULBS WERE THE CORRECT MODEL AND HAD BEEN INSTALLED CORRECTLY. SOME OF THE PLASTIC HAD MELTED DOWN ONTO THE BULB ITSELF AND COULD POTENTIALLY BECOME A FIRE HAZARD. THIS PROBLEM IMPACTED BOTH DRIVER AND PASSENGER SIDES, WITH THE DRIVER SIDE APPEARING MORE SIGNIFICANTLY MELTED. AFTER A QUICK SEARCH ON MAZDA FORUMS, THIS APPEARS TO BE AN ISSUE EXPERIENCED BY MANY OWNERS OF 2007 MAZDA 3 MODELS, BUT ONLY THOSE IN THE HATCHBACK CONFIGURATION. *TR
THE CHECK ENGINE LIGHT CAME ON. CAUSE ,AFTER RUNNING CODE CHECK,P2004. RUNNER CONTROL VALE STUCK. REPLACE SOLENOID. FRONT STRUTS GONE. *TR
TL* THE CONTACT OWNS A 2007 MAZDA 3. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 55 MPH, THE POWER STEERING ASSIST FAILED WITHOUT WARNING. THE VEHICLE WAS MANEUVERED TO THE SIDE OF THE ROAD. THE VEHICLE DID RESTART. THIS FAILURE HAD OCCURRED SEVEN TIMES OVER A PERIOD OF SEVEN MONTHS. THE VEHICLE WAS TAKEN TO THE DE…
Read full complaint
TL* THE CONTACT OWNS A 2007 MAZDA 3. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 55 MPH, THE POWER STEERING ASSIST FAILED WITHOUT WARNING. THE VEHICLE WAS MANEUVERED TO THE SIDE OF THE ROAD. THE VEHICLE DID RESTART. THIS FAILURE HAD OCCURRED SEVEN TIMES OVER A PERIOD OF SEVEN MONTHS. THE VEHICLE WAS TAKEN TO THE DEALER WHO COULD NOT DUPLICATE THE FAILURE. THE MANUFACTURER WAS NOTIFIED AND ADVISED THE CONTACT THAT THE VEHICLE WAS NOT INCLUDED ANY RECALLS. THE APPROXIMATE FAILURE MILEAGE WAS NOT AVAILABLE.
WE JUST NOTICED THAT BOTH TAIL/BRAKE LIGHTS HAVE MELTED HOLES IN THE SURROUNDING INSIDE RED PLASTIC LENS. THE BULBS ARE THE ORIGINALS AS ARE THE LENS. THE HEAT IS NOW STARTING TO AFFECT THE OUTSIDE CLEAR COVER. THE OUTSIDE COVERS ARE STILL INTACT, BUT LOOK BUBBLY; THE HOLES IN THE INNER RED LENS LET WHITE LIGHT COME OUT AND IT L…
Read full complaint
WE JUST NOTICED THAT BOTH TAIL/BRAKE LIGHTS HAVE MELTED HOLES IN THE SURROUNDING INSIDE RED PLASTIC LENS. THE BULBS ARE THE ORIGINALS AS ARE THE LENS. THE HEAT IS NOW STARTING TO AFFECT THE OUTSIDE CLEAR COVER. THE OUTSIDE COVERS ARE STILL INTACT, BUT LOOK BUBBLY; THE HOLES IN THE INNER RED LENS LET WHITE LIGHT COME OUT AND IT LOOKS LIKE WE HAVE BACK-UP LIGHTS ON CONTINUOUSLY AT NIGHT.
I WAS DRIVER MY MAZDA3I WHEN SUDDENLY IN BECAME HARD FOR ME TO STEER MY CAR AND IT JUST CUT OFF. I CALL THE DEAL IN BROUGHT IN MY CAR WHERE INFORMED ME IT WAS THE POWER STEERING AND I CONTACT MAZDA BECAUSE OF THE SAFETY RECALL AND THEY TOLD ME I WASN'T ELIGIBLE FOR THE FIX. *TR
WHILE DRIVING ON THE HIGHWAY, I EXPERIENCED A SUDDEN LOSS OF POWER STEERING. I FELT A SUDDEN JERK IN THE VEHICLE AND GOT SCARED. I SAW THE POWER STEERING LIGHT ON, AS WELL AS A COUPLE OF OTHER LIGHTS WHICH I DO NOT RECALL. THERE WAS NO POWER STEERING FOR ABOUT 10 SECONDS. AFTER 10 SECONDS, POWER STEERING SPONTANEOUSLY CAME BACK …
Read full complaint
WHILE DRIVING ON THE HIGHWAY, I EXPERIENCED A SUDDEN LOSS OF POWER STEERING. I FELT A SUDDEN JERK IN THE VEHICLE AND GOT SCARED. I SAW THE POWER STEERING LIGHT ON, AS WELL AS A COUPLE OF OTHER LIGHTS WHICH I DO NOT RECALL. THERE WAS NO POWER STEERING FOR ABOUT 10 SECONDS. AFTER 10 SECONDS, POWER STEERING SPONTANEOUSLY CAME BACK AND I PULLED TO THE SIDE OF THE ROAD AND TURNED OFF THE CAR. AFTER RESTARTING THE CAR, I HAVE NOT EXPERIENCED THE ISSUE AGAIN YET, BUT IT HAS ONLY BEEN A COUPLE OF HOURS. *TR
I WAS NOTIFIED BY THE MAZDA DEALERSHIP THAT AN INTEGRAL HYDRAULIC ENGINE MOUNT WAS CRACKING AND NEEDED REPLACEMENT. I WAS JUST PAST MY CAR'S WARRANTY SO I DROVE ON IT SINCE THEY SAID IT WAS SAFE. ON NOVEMBER 8TH 2013 DURING A SERVICE I WAS TOLD THE INTEGRAL MOUNT WAS ABOUT TO BREAK AND NEEDED IMMEDIATE REPLACEMENT. THEY SAID …
Read full complaint
I WAS NOTIFIED BY THE MAZDA DEALERSHIP THAT AN INTEGRAL HYDRAULIC ENGINE MOUNT WAS CRACKING AND NEEDED REPLACEMENT. I WAS JUST PAST MY CAR'S WARRANTY SO I DROVE ON IT SINCE THEY SAID IT WAS SAFE. ON NOVEMBER 8TH 2013 DURING A SERVICE I WAS TOLD THE INTEGRAL MOUNT WAS ABOUT TO BREAK AND NEEDED IMMEDIATE REPLACEMENT. THEY SAID IF THE MOUNT HAD BROKEN WHILE DRIVING IT COULD CAUSE AN ACCIDENT, NOT TO MENTION DESTROY THE MOTOR. I HAD THEM REPLACE IT BUT HAD TO PAY OUT OF POCKET SINCE IT WAS PAST WARRANTY AND NOT A RECALL. I RESEARCHED ONLINE AND FOUND NUMEROUS COMPLAINTS FROM OTHER OWNERS OF THE SAME SERIES CAR AND WITHIN ADJACENT YEARS OF THE SAME MOTOR MOUNT CRACKING AND NEEDING REPLACEMENT UNDER 50,000 MILES. SOME COMPLAINED ABOUT HAVING TO REPLACE THE REPLACEMENT LATER AFTER PUTTING SOME MORE MILEAGE ON IT. THIS IS AN OBVIOUSLY INHERENTLY DEFECTIVE PART THAT SHOULD BE RECALLED. PLEASE LOOK INTO THIS AND FORCE MAZDA TO RECALL THIS DEFECT AS IT IS A DANGER TO PUBLIC SAFETY IF ONE WERE TO BREAK WHILE DRIVING. THANK YOU SO MUCH FOR YOUR TIME AND SERVICE. *TR
AFTER PUTTING AIR IN THE TIRES, I DROVE APPROXIMATELY 2 MILES DOWN THE ROAD WHEN THE TIRE LIGHT CAME ON. I DROVE APPROXIMATELY 1 MORE MILE TO MY HOUSE. THE TIRE WENT COMPLETELY FLAT DUE TO A BROKEN VALVE STEM. *TR
Official recalls
221V494000 · Air Bags:frontal
Jul 1, 2021
Mazda North American Operations (Mazda) is recalling certain 2004-2007 Mazda3 vehicles. During air bag deployment, the plastic emblem on the steering wheel air bag module cover may shatter, and project plastic fragments into the vehicle.
Consequence & remedy
Consequence: Plastic fragments can hit occupants during air bag deployment, increasing the risk of injury.
Remedy: Dealers will replace the air bag module cover, free of charge. Owner letters were mailed between August 28, 2021 and October 28, 2021. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 4921G.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.