IllustrationI HAD A SERIOUS ACCIDENT BECAUSE MY STEERING LOCKED UP SO I COULDN'T STEER MY STEERING WHEEL . I ROLLED MY CAR AND NEARLY WAS KILLED
2007 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2007 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
270–25K
3325–50K
3250–75K
3475–100K
39100–150K
18150K+
183 reports with mileage · 39 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 89 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 36 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
28 crash reports3 fire reports16 injury reports
Vehicle Speed Control complaints
9 reportsI HAVE A MANUAL TRANSMISSION AND MY CAR TWICE NOW HAS HAD THE ACCELERATOR PEDAL GO ALL THE TO THE FLOOR AND GETS STUCK ALL THE WAY DOWN WHILE I AM DRIVING ON THE FREEWAY. TWO OTHER TIMES IT HAS, WHILE SHIFTING OUT OF ONE GEAR AND INTO ANOTHER, IMMEDIATELY REV UP TO 8 RPMS (MAX FOR MY VEHICLE) AGAIN WHILE ON THE FREEWAY FORCING M…
Read full complaint
I HAVE A MANUAL TRANSMISSION AND MY CAR TWICE NOW HAS HAD THE ACCELERATOR PEDAL GO ALL THE TO THE FLOOR AND GETS STUCK ALL THE WAY DOWN WHILE I AM DRIVING ON THE FREEWAY. TWO OTHER TIMES IT HAS, WHILE SHIFTING OUT OF ONE GEAR AND INTO ANOTHER, IMMEDIATELY REV UP TO 8 RPMS (MAX FOR MY VEHICLE) AGAIN WHILE ON THE FREEWAY FORCING ME TO PULL ONTO THE SHOULDER AND WAIT FOR THE CAR TO QUIT REVVING. THAT HAS OCCURRED WHILE MERGING ONTO THE FREEWAY IN BETWEEN GEARS MAKING ME UNABLE TO GET IT BACK INTO A GEAR. *TR
TL* THE CONTACT OWNS A 2007 MAZDA MAZDA 3. THE CONTACT STATED THAT AFTER DECELERATING TO A STOP, THE VEHICLE WOULD LUNGE FORWARD ABNORMALLY AND THE CHECK ENGINE LIGHT ILLUMINATED IMMEDIATELY AFTER THE FAILURE. THE VEHICLE WAS NOT TAKEN TO A DEALER OR AN INDEPENDENT MECHANIC. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT…
Read full complaint
TL* THE CONTACT OWNS A 2007 MAZDA MAZDA 3. THE CONTACT STATED THAT AFTER DECELERATING TO A STOP, THE VEHICLE WOULD LUNGE FORWARD ABNORMALLY AND THE CHECK ENGINE LIGHT ILLUMINATED IMMEDIATELY AFTER THE FAILURE. THE VEHICLE WAS NOT TAKEN TO A DEALER OR AN INDEPENDENT MECHANIC. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT CONTACTED. THE FAILURE MILEAGE WAS UNKNOWN. THE CURRENT MILEAGE WAS APPROXIMATELY 93,000. THE VIN WAS UNAVAILABLE.
ACCELERATOR PEDAL STUCK AFTER ENGAGING IT TO MERGE ONTO FREEWAY. CRUISE CONTROL WAS NOT ON. BRAKES BARELY SLOWED ACCELERATION. THREW VEHICLE INTO NEUTRAL TO STOP ACCELERATION. WHEN VEHICLE PUT BACK IN DRIVE, PEDAL AND ACCELERATOR FUNCTIONED NORMALLY. WHEN TAKEN IN TO MECHANIC, FOUND TO BE FUNCTIONING NORMALLY. *TR
TL*THE CONTACT OWNS A 2007 MAZDA 3. THE CONTACT STATED THAT WHEN TRYING TO DECELERATE AND PARK, THE VEHICLE SUDDENLY ACCELERATED FORWARD AND CRASHED INTO A WALL. NO ONE WAS INJURED. THE POLICE WERE NOT NOTIFIED. THE VEHICLE WAS TOWED TO A DEALER WHO HAD NOT COMPLETED THE DIAGNOSTIC TEST WHEN THE COMPLAINT WAS FILED. THE FAILURE …
Read full complaint
TL*THE CONTACT OWNS A 2007 MAZDA 3. THE CONTACT STATED THAT WHEN TRYING TO DECELERATE AND PARK, THE VEHICLE SUDDENLY ACCELERATED FORWARD AND CRASHED INTO A WALL. NO ONE WAS INJURED. THE POLICE WERE NOT NOTIFIED. THE VEHICLE WAS TOWED TO A DEALER WHO HAD NOT COMPLETED THE DIAGNOSTIC TEST WHEN THE COMPLAINT WAS FILED. THE FAILURE AND CURRENT MILEAGES WERE APPROXIMATELY 25,000. THE VIN WAS UNAVAILABLE.
TL*THE CONTACT OWNS A 2007 MAZDA, MAZDA3. WHILE DRIVING APPROXIMATELY 35 MPH, THE VEHICLE BEGAN TO SUDDENLY ACCELERATE. WHEN THE CONTACT DISENGAGED THE CLUTCH, THE ENGINE RPMS FLUCTUATED BETWEEN 6,800 AND 7,300. THE VEHICLE WAS DRIVEN TO THE SIDE OF THE ROAD, THE ENGINE WAS TURNED OFF AND RESTARTED TWICE BEFORE RESUMING NORMALLY…
Read full complaint
TL*THE CONTACT OWNS A 2007 MAZDA, MAZDA3. WHILE DRIVING APPROXIMATELY 35 MPH, THE VEHICLE BEGAN TO SUDDENLY ACCELERATE. WHEN THE CONTACT DISENGAGED THE CLUTCH, THE ENGINE RPMS FLUCTUATED BETWEEN 6,800 AND 7,300. THE VEHICLE WAS DRIVEN TO THE SIDE OF THE ROAD, THE ENGINE WAS TURNED OFF AND RESTARTED TWICE BEFORE RESUMING NORMALLY. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE FAILURE MILEAGE WAS APPROXIMATELY 76,170. UPDATED 03/02/11 *BF UPDATED 03/08/11
THE RESUME FUNCTION ON THE CRUISE CONTROL SOMETIMES EXCEEDS THE SET SPEED AND FAILS TO UPSHIFT. AN EXAMPLE OF THE SCENARIO IS THE CRUISE SET SPEED IS 75 MPH. I APPROACH A CAR GOING 65 MPH AND PRESS THE CANCEL BUTTON WHICH DISENGAGES THE CRUISE CONTROL. THE CAR PULLS OVER AND I PRESS THE RESUME BUTTON. THE TRANSMISSION WILL S…
Read full complaint
THE RESUME FUNCTION ON THE CRUISE CONTROL SOMETIMES EXCEEDS THE SET SPEED AND FAILS TO UPSHIFT. AN EXAMPLE OF THE SCENARIO IS THE CRUISE SET SPEED IS 75 MPH. I APPROACH A CAR GOING 65 MPH AND PRESS THE CANCEL BUTTON WHICH DISENGAGES THE CRUISE CONTROL. THE CAR PULLS OVER AND I PRESS THE RESUME BUTTON. THE TRANSMISSION WILL SOMETIMES DOWNSHIFT TO EITHER 3RD OR 4TH GEAR AND QUICKLY ACCELERATE TO 78 MPH AND STAY IN THE LOWER GEAR. I AM NOT TOUCHING ANY PEDALS NOR THE GEAR SHIFT WHICH IS STILL IN THE AUTO POSITION. THE TRANSMISSION WILL STAY IN THE LOWER GEAR AT THE HIGHER SPEED INDEFINITELY. IF I PRESS CANCEL AND THEN RESUME IT WILL IMMEDIATELY SHIFT TO 5TH GEAR AND RETURN TO THE 75 MPH SET SPEED. THE PROBLEM IS INTERMITTENT AND HAS HAPPENED ABOUT 10-12 TIMES IN THE LAST YEAR. I DO USE THE CRUISE FUNCTION DAILY ON THE INTERSTATE, BUT DON'T ENCOUNTER THE DESCRIBED SITUATION VERY OFTEN. I HAVE TRIED TO REPRODUCE THE PROBLEM A FEW TIMES WITHOUT SUCCESS. I HAVE TAKEN THE CAR TO THE DEALER BUT THEY WERE ALSO UNABLE TO REPRODUCE THE PROBLEM OR FIND ANY OTHER PROBLEMS WITH THE CRUISE FUNCTION. THEY ALSO STATED THERE WAS NO TECH BULLETIN DESCRIBING THIS PROBLEM. AN EMAIL TO MAZDA WAS RESPONDED TO BY SUGGESTING I TAKE THE CAR TO THE DEALER. I AM A VERY EXPERIENCED DRIVER. I KNOW WITH ABSOLUTE CERTAINTY THAT I AM NOT TOUCHING ANY PEDALS AND THAT THE GEAR SHIFT IS IN THE AUTO POSITION. THIS IS NOT A CASE OF DRIVER ERROR. THERE IS A CLEAR DEFECT IN THE FUNCTIONING OF THE CRUISE CONTROL OR TRANSMISSION OPERATION. IN EVERY OTHER WAY THE CRUISE AND TRANSMISSION OPERATION HAS BEEN COMPLETELY NORMAL. *TR
ON 2/08/2007 MY NEWLY PURCHASED MAZDA 3 WAS RUNNING FOR 45 MINUTES AT 40 MILES PER HOUR AND THE ENGINE RACED. ON 2/16/2007, THE ENGINE RACED AGAIN AND THE CAR SWITCHED FROM FIRST GEAR TO 5TH GEAR IN 1 SECOND WHILE THE ENGINE RACED. ON 2/19/2007, THE BRAKES FAILED TO STOP, NARROWLY AVOIDING AN ACCIDENT WHILE THE ENGINE RACED. T…
Read full complaint
ON 2/08/2007 MY NEWLY PURCHASED MAZDA 3 WAS RUNNING FOR 45 MINUTES AT 40 MILES PER HOUR AND THE ENGINE RACED. ON 2/16/2007, THE ENGINE RACED AGAIN AND THE CAR SWITCHED FROM FIRST GEAR TO 5TH GEAR IN 1 SECOND WHILE THE ENGINE RACED. ON 2/19/2007, THE BRAKES FAILED TO STOP, NARROWLY AVOIDING AN ACCIDENT WHILE THE ENGINE RACED. THE CAR WAS PUT IN PARK AND THE ENGINE RACED AGAIN. EARLIER THAT SAME DAY, THE CAR CHANGED FROM FIRST GEAR TO FIFTH GEAR AND THEN TO SECOND GEAR WHILE MAKING A CLICKING SOUND. WHEN IT WAS CHECKED OUT BY THE MAZDA DEALERSHIP, THEY SAID THERE WAS NOTHING WRONG WITH THE CAR. THIS CAR COULD HAVE CAUSED A HORRIFIC ACCIDENT AND STILL COULD. *JB
I HAVE SUSTAINED A PAINFUL ERGONOMIC INJURY TO MY RIGHT ACHILLES TENDON FROM THE POOR DESIGN OF THE ACCELERATOR/BRAKE AREA AND THE LIMITED SEAT ADJUSTMENT IN THIS CAR (2007 MAZDA SPEED 3). I HAVE TO ICE MY ANKLE EVERY NIGHT. WHEN DRIVING IT IS PAINFUL AND CAN BECOME NUMB, REDUCING MY ABILITY TO DO EMERGENCY BRAKING. I AM CONCE…
Read full complaint
I HAVE SUSTAINED A PAINFUL ERGONOMIC INJURY TO MY RIGHT ACHILLES TENDON FROM THE POOR DESIGN OF THE ACCELERATOR/BRAKE AREA AND THE LIMITED SEAT ADJUSTMENT IN THIS CAR (2007 MAZDA SPEED 3). I HAVE TO ICE MY ANKLE EVERY NIGHT. WHEN DRIVING IT IS PAINFUL AND CAN BECOME NUMB, REDUCING MY ABILITY TO DO EMERGENCY BRAKING. I AM CONCERNED THAT THIS WILL LEAD TO AN ACCIDENT. THE ISSUE STARTED IN EARLY JANUARY WITH LESS THAN 100 MILES ON THE CAR - NOW I HAVE 1300 ON THE CAR AND EXPERIENCE THIS EVERY DAY I DRIVE THE VEHICLE. *NM
Official recalls
221V494000 · Air Bags:frontal
Jul 1, 2021
Mazda North American Operations (Mazda) is recalling certain 2004-2007 Mazda3 vehicles. During air bag deployment, the plastic emblem on the steering wheel air bag module cover may shatter, and project plastic fragments into the vehicle.
Consequence & remedy
Consequence: Plastic fragments can hit occupants during air bag deployment, increasing the risk of injury.
Remedy: Dealers will replace the air bag module cover, free of charge. Owner letters were mailed between August 28, 2021 and October 28, 2021. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 4921G.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.