IllustrationTL* THE CONTACT OWNS A 2007 MAZDA 3. THE CONTACT HEARD AN ABNORMAL NOISE COMING FROM THE ENGINE. THE CONTACT NOTICED THAT THE VEHICLE HAD EXCESSIVELY CONSUMED ALL THE OIL IN THE ENGINE. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 192,000.
2007 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2007 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
270–25K
3325–50K
3250–75K
3475–100K
39100–150K
18150K+
183 reports with mileage · 39 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 89 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 36 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
28 crash reports3 fire reports16 injury reports
Engine complaints
22 reportsWAS DRIVING DOWN THE FREEWAY AND ALL OF A SUDDEN IT SOUNDED LIKE I RAN OVER A LARGE PIECE OF DEBRIS AND THE CAR JOLTED. I TRIED TO ACCELERATE BUT THERE WAS NO RESPONSE AND SAFELY PULLED OVER. TURNED THE CAR OFF AND TRIED TO TURN IT BACK ON BUT THERE WAS NO TURNOVER. LOOKED AT IT AND THERE WAS OIL MIXED WITH METAL SHARDS AND A CR…
Read full complaint
WAS DRIVING DOWN THE FREEWAY AND ALL OF A SUDDEN IT SOUNDED LIKE I RAN OVER A LARGE PIECE OF DEBRIS AND THE CAR JOLTED. I TRIED TO ACCELERATE BUT THERE WAS NO RESPONSE AND SAFELY PULLED OVER. TURNED THE CAR OFF AND TRIED TO TURN IT BACK ON BUT THERE WAS NO TURNOVER. LOOKED AT IT AND THERE WAS OIL MIXED WITH METAL SHARDS AND A CRACK IN THE ENGINE. TOOK IT TO THE DEALERSHIP OF PURCHASE AND IT WAS DETERMINED THAT THE ENGINE HAD BLOWN. LET THE MANUFACTURER KNOW BUT THEY DID NOTHING TO HELP.
I HAVE BEEN HAVING ISSUES WITH THIS VEHICLE EVER SINCE I PURCHASED IT FROM A DEALERSHIP IN WOODBRIDGE, VA. THE CAR'S GEARS DOES NOT SHIFT CORRECTLY AND THE ENGINE CONTINUOUSLY STALLS. IF I'M AT A TRAFFIC LIGHT AND THE LIGHT SWITCHES FROM RED TO GREEN THE VEHICLE JUMPS AS IF IT'S GOING TO CUT OFF. MY AT LIGHT ALSO CAME ON AND MY …
Read full complaint
I HAVE BEEN HAVING ISSUES WITH THIS VEHICLE EVER SINCE I PURCHASED IT FROM A DEALERSHIP IN WOODBRIDGE, VA. THE CAR'S GEARS DOES NOT SHIFT CORRECTLY AND THE ENGINE CONTINUOUSLY STALLS. IF I'M AT A TRAFFIC LIGHT AND THE LIGHT SWITCHES FROM RED TO GREEN THE VEHICLE JUMPS AS IF IT'S GOING TO CUT OFF. MY AT LIGHT ALSO CAME ON AND MY CHECK ENGINE LIGHT COMES ON AND OFF. EVERY TIME THE VEHICLE'S ENGINE LIGHT IS CHECKED, IT'S BECAUSE OF "THE THERMOSTAT" WHICH I'VE SEEN MANY COMPLAINTS FROM OWNERS OF THE SAME TYPE OF VEHICLE. ALTHOUGH, THE ENGINE CODE IS COMING UP AS AN ISSUE WITH THE THERMOSTAT, THERE'S ACTUALLY NEVER AN ISSUE. I SEARCHED MY VIN AND ITS STATING THERE ARE NO OPEN RECALLS FOR MY VEHICLE, BUT I'M HAVING THE SAME ISSUES AS THE OPEN RECALLS FOR THIS PARTICULAR MAKE AND MODEL FOR 2007. I BOUGHT THE VEHICLE OCTOBER 2013 SO THERE'S NO WAY MAZDA COULD'VE SENT ME INFORMATION PERTAINING TO THE RECALL AND THE DEALERSHIP DID NOT INFORM ME OF THIS EITHER. *TR
UPON STOPPING AT A RED LIGHT MY CAR STARTED SHAKING REALLY BADLY AND THEN SHUT OFF. THIS HAS HAPPENED ON NUMEROUS OCCASIONS SINCE THE INITIAL INCIDENT. WHEN THE BRAKES ARE NOT APPLIED, THE ENGINE WILL NOT SHAKE, BUT OBVIOUSLY FOR SAFETY REASONS, THE BREAKS MUST BE APPLIED WHILE STOPPED AT A TRAFFIC LIGHT. ON 3 OTHER OCCASIONS TH…
Read full complaint
UPON STOPPING AT A RED LIGHT MY CAR STARTED SHAKING REALLY BADLY AND THEN SHUT OFF. THIS HAS HAPPENED ON NUMEROUS OCCASIONS SINCE THE INITIAL INCIDENT. WHEN THE BRAKES ARE NOT APPLIED, THE ENGINE WILL NOT SHAKE, BUT OBVIOUSLY FOR SAFETY REASONS, THE BREAKS MUST BE APPLIED WHILE STOPPED AT A TRAFFIC LIGHT. ON 3 OTHER OCCASIONS THE CAR TURNED OFF JUST AS I WAS GIVING IT GAS TO START GOING AGAIN, RESULTING IN ME HAVING TO COAST OVER TO THE SHOULDER (WITH THE CAR BEING OFF AND NO POWER STEERING TO ASSIST) IN ORDER TO GET MY CAR STARTED AGAIN. THIS IS A DANGEROUS FAULT THAT I HAVE SEEN SO MANY PEOPLE COMPLAIN OF. I HAVE READ IT IS DUE TO A FAULTY PURGE SOLENOID VALVE ALONG WITH OTHER THINGS, BUT NO ONE AT MAZDA SEEMS TO KNOW OR CARE MUCH ABOUT IT. *TR
CRACKED ENGINE MOUNTS. COMMON PROBLEM IN THE VEHICLE YEAR AND MODEL. SHOULD BE LOOKED AT FOR RECALL. *TR
THERE IS AN ISSUE WITH THE REAR BRAKE LIGHT ASSEMBLY, THE RED PLASTIC ASSEMBLY MELTED INTO THE BREAK LIGHT BULBS CAUSING BOTH REAR BRAKE LIGHTS TO BURN OUT. CURRENTLY, BOTH ASSEMBLY HAVE HOLES WHERE THE RED PLASTIC MELTED, THIS IS A POTENTIAL FIRE HAZARD. THERE IS AN ISSUE WITH THE FRONT PASSENGER SIDE ENGINE MOUNT, IT HAS BEEN …
Read full complaint
THERE IS AN ISSUE WITH THE REAR BRAKE LIGHT ASSEMBLY, THE RED PLASTIC ASSEMBLY MELTED INTO THE BREAK LIGHT BULBS CAUSING BOTH REAR BRAKE LIGHTS TO BURN OUT. CURRENTLY, BOTH ASSEMBLY HAVE HOLES WHERE THE RED PLASTIC MELTED, THIS IS A POTENTIAL FIRE HAZARD. THERE IS AN ISSUE WITH THE FRONT PASSENGER SIDE ENGINE MOUNT, IT HAS BEEN REPLACED THREE TIMES AND CONTINUES TO FAIL, MIGHT AN ENGINEERING DEFECT ON THE ENGINE MOUNT. FINALLY, DASHBOARD AIRBAG INDICATOR HAS TURNED ON UNEXPECTEDLY AND HAS REMAINED ON EVER SINCE, MIGHT BE DEFECTIVE PART IN THE SRS AIRBAG SYSTEM. *TR
TL* THE CONTACT OWNS A 2007 MAZDA 3. THE CONTACT STATED THAT THE VEHICLE FAILED TO START WHEN THE FUEL TANK WAS FILLED. THE DEALER PERFORMED A DIAGNOSTIC, WHICH LOCATED A FAILURE CODE AT THE PURGE VALVE. THE VALVE WAS REPLACED, BUT THE VEHICLE EXPERIENCED ADDITIONAL FAILURES. THE FRONT END VIBRATED AND THE ENGINE STALLED WHILE D…
Read full complaint
TL* THE CONTACT OWNS A 2007 MAZDA 3. THE CONTACT STATED THAT THE VEHICLE FAILED TO START WHEN THE FUEL TANK WAS FILLED. THE DEALER PERFORMED A DIAGNOSTIC, WHICH LOCATED A FAILURE CODE AT THE PURGE VALVE. THE VALVE WAS REPLACED, BUT THE VEHICLE EXPERIENCED ADDITIONAL FAILURES. THE FRONT END VIBRATED AND THE ENGINE STALLED WHILE DRIVING 65 MPH. THE DEALER PERFORMED DIAGNOSTIC TESTING, WHICH INDICATED THAT THE ENGINE MOUNT WAS WORN, THE STRUTS LEAKED, AND THE EVAP SYSTEM FAILED. HOWEVER, THE VALVES WERE REPLACED. THE ENGINE MOUNT, STRUTS, AND EVAPORATING SYSTEM WERE NOT REPLACED. THE ROTOR ALSO WORE PREMATURELY AND COULD NOT BE RESURFACED. THE FRONT BUMPER CLIPS FAILED DUE TO DEFECTIVE PLASTIC. THE CLIPS WERE REPLACED SEVERAL TIMES; HOWEVER, THE FAILURE WAS NOT CORRECTED. THE MANUFACTURER STATED THAT THE VEHICLE WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 07V295000 (ENGINE AND ENGINE COOLING). THE FAILURE MILEAGE WAS 50,000.
WHILE DRIVING MY CAR TO TURN INTO THE SHOPPING CENTER PARKING LOT, THE STEERING WHEEL LOCKED UP AND WAS VERY STIFF. AT THE SAME TIME THE ENGINE SHUT OFF AND ESSENTIALLY CAUSING MY CAR TO STOP IN THE MIDDLE OF THE PARKING LOT. ALL ENGINE, POWER, AND BATTERY LIGHTS FLASHED ON AND OFF AT THE SAME TIME. I ENDED UP PUTTING THE CAR I…
Read full complaint
WHILE DRIVING MY CAR TO TURN INTO THE SHOPPING CENTER PARKING LOT, THE STEERING WHEEL LOCKED UP AND WAS VERY STIFF. AT THE SAME TIME THE ENGINE SHUT OFF AND ESSENTIALLY CAUSING MY CAR TO STOP IN THE MIDDLE OF THE PARKING LOT. ALL ENGINE, POWER, AND BATTERY LIGHTS FLASHED ON AND OFF AT THE SAME TIME. I ENDED UP PUTTING THE CAR IN PARK TURN OFF THE CAR WITH MY KEY AND THEN RESTARTING IT AGAIN. AFTER RESEARCHING I SAW THERE WAS A RECALL FOR MY MODEL AND YEAR, WHEN I CALLED THE CUSTOMER SERVICE DEPARTMENT THE REP NOT HAVING ANY NOTICE FOR A RECALL FOR MY TYPE OF MODEL AND DID NOT HONOR THE RECALL THAT I HAD MENTIONED TO HIM. I AM NOW HAVING TO LOOK OUTSIDE OF MY MEANS IN ORDER TO PAY FOR THIS ISSUE. *TR
VEHICLE WAS TRAVELING ALONG ON 30 MPH ROAD WITH 'STOP' SIGN AHEAD. AS VEHICLE SLOWED DOWN TO ABOUT 15 MPH, TRANSMISSION STARTED TO SHAKE, SEVERAL WARNING LIGHTS CAME ON AND OFF, INCLUDING OIL AND POWER STEERING, RPM FELL VERY CLOSE TO 0 (ZERO) AND CAR DIED. VEHICLE WAS ABLE TO STOP AT THE 'STOP' SIGN. EVEN THOUGH THE VEHICLE WAS…
Read full complaint
VEHICLE WAS TRAVELING ALONG ON 30 MPH ROAD WITH 'STOP' SIGN AHEAD. AS VEHICLE SLOWED DOWN TO ABOUT 15 MPH, TRANSMISSION STARTED TO SHAKE, SEVERAL WARNING LIGHTS CAME ON AND OFF, INCLUDING OIL AND POWER STEERING, RPM FELL VERY CLOSE TO 0 (ZERO) AND CAR DIED. VEHICLE WAS ABLE TO STOP AT THE 'STOP' SIGN. EVEN THOUGH THE VEHICLE WAS STILL ON, ANY PRESSURE ON THE GAS PEDAL DID NOT PROVIDE POWER OR INPUT TO THE TRANSMISSION, NOW IN 1ST GEAR, TO MOVE THE CAR. CAR NEEDED TO BE COMPLETELY TURNED OFF AND THEN TURNED ON BEFORE IT COULD MOVE AGAIN. THIS ISSUE HAS BEEN ONGOING FOR 4 YEARS REGARDLESS OF SPEED. THE CAR HAS ALSO DECIDED TO STOP PROVIDING POWER WHILE IN MOTION WHILE IN MOVING TRAFFIC OR ON THE HIGHWAY, WHICH COULD HAVE RESULTED IN MULTIPLE CAR CRASHES OR WORSE. MAZDA REFUSES TO ACKNOWLEDGE THAT ANYTHING IS WRONG WITH THE CAR SINCE THEY "CANNOT REPLICATE THE PROBLEM". THIS ISSUE IS SPORADIC AND OCCURS REGARDLESS OF SPEED (USUALLY AROUND 30 MPG OR LESS), WEATHER, DISTANCE TRAVELED, AMOUNT OF TIME CAR HAS BEEN IN CONSISTENT USE, ETC. MAZDA HAS EVEN HOOKED THIS CAR UP TO THEIR COMPUTER SYSTEM AND NO ERROR CODE HAS BEEN FOUND. THIS ISSUE HAS BEEN EXTENSIVELY DOCUMENTED WITH OUR LOCAL MAZDA DEALER AND PAPERWORK IS AVAILABLE FOR REVIEW. THIS CAR HAS BEEN A TRUE LEMON SINCE WE BOUGHT IT. IT ONLY HAS ROUGHLY 55K MILES ON IT. *TR
I WAS NOTIFIED BY THE MAZDA DEALERSHIP THAT AN INTEGRAL HYDRAULIC ENGINE MOUNT WAS CRACKING AND NEEDED REPLACEMENT. I WAS JUST PAST MY CAR'S WARRANTY SO I DROVE ON IT SINCE THEY SAID IT WAS SAFE. ON NOVEMBER 8TH 2013 DURING A SERVICE I WAS TOLD THE INTEGRAL MOUNT WAS ABOUT TO BREAK AND NEEDED IMMEDIATE REPLACEMENT. THEY SAID …
Read full complaint
I WAS NOTIFIED BY THE MAZDA DEALERSHIP THAT AN INTEGRAL HYDRAULIC ENGINE MOUNT WAS CRACKING AND NEEDED REPLACEMENT. I WAS JUST PAST MY CAR'S WARRANTY SO I DROVE ON IT SINCE THEY SAID IT WAS SAFE. ON NOVEMBER 8TH 2013 DURING A SERVICE I WAS TOLD THE INTEGRAL MOUNT WAS ABOUT TO BREAK AND NEEDED IMMEDIATE REPLACEMENT. THEY SAID IF THE MOUNT HAD BROKEN WHILE DRIVING IT COULD CAUSE AN ACCIDENT, NOT TO MENTION DESTROY THE MOTOR. I HAD THEM REPLACE IT BUT HAD TO PAY OUT OF POCKET SINCE IT WAS PAST WARRANTY AND NOT A RECALL. I RESEARCHED ONLINE AND FOUND NUMEROUS COMPLAINTS FROM OTHER OWNERS OF THE SAME SERIES CAR AND WITHIN ADJACENT YEARS OF THE SAME MOTOR MOUNT CRACKING AND NEEDING REPLACEMENT UNDER 50,000 MILES. SOME COMPLAINED ABOUT HAVING TO REPLACE THE REPLACEMENT LATER AFTER PUTTING SOME MORE MILEAGE ON IT. THIS IS AN OBVIOUSLY INHERENTLY DEFECTIVE PART THAT SHOULD BE RECALLED. PLEASE LOOK INTO THIS AND FORCE MAZDA TO RECALL THIS DEFECT AS IT IS A DANGER TO PUBLIC SAFETY IF ONE WERE TO BREAK WHILE DRIVING. THANK YOU SO MUCH FOR YOUR TIME AND SERVICE. *TR
Official recalls
221V494000 · Air Bags:frontal
Jul 1, 2021
Mazda North American Operations (Mazda) is recalling certain 2004-2007 Mazda3 vehicles. During air bag deployment, the plastic emblem on the steering wheel air bag module cover may shatter, and project plastic fragments into the vehicle.
Consequence & remedy
Consequence: Plastic fragments can hit occupants during air bag deployment, increasing the risk of injury.
Remedy: Dealers will replace the air bag module cover, free of charge. Owner letters were mailed between August 28, 2021 and October 28, 2021. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 4921G.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.