Service Brakes. Review the 39 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Engine. Review the 32 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Electrical System. Review the 27 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

6 crash reports3 fire reports3 injury reports

Service Brakes complaints

39 reports

Clear category filter

Mileage unknown · Aug 28, 2026

Service Brakes

Unknown there were no incidents But the recall is almost 1 year old I received the notice September 2025 regarding a possible brake hose defect waiting almost 1 year for a Fix is Rediclous there had been no updates from Ford/Lincoln motor company brake issue should be taken more Seriously

NHTSA ODI #11760452

52,000 miles · Aug 24, 2026

Back Over PreventionService BrakesService Brakes, Hydraulic

Read full complaint

The contact owns a 2016 Lincoln MKX. The contact stated that while operating the vehicle and depressing the brake pedal, the vehicle failed to immediately stop with the message “Low Brake Fluid” displayed. Brake fluid was later added to the brake reservoir, and the vehicle was driven to the local mechanic, who diagnosed that the brake hoses were faulty and needed to be replaced. The brake hoses were replaced, and the vehicle was repaired. The contact previously received notification of NHTSA Campaign Number: 20V469000 (SERVICE BRAKES, SERVICE BRAKES, HYDRAULIC). Additionally, the contact stated that the back over prevention camera had intermittently failed. The cause of the failure was not yet determined. The manufacturer and local dealer were not yet contacted. The failure mileage was approximately 52,000.

NHTSA ODI #11759040

Mileage unknown · Aug 14, 2026

Service Brakes

It has been almost a year since this recall came out and there is not a remedy available. the manufacturer has failed to provide a remedy for it since it came out on August 25, 2026

NHTSA ODI #11756997

Mileage unknown · Jun 16, 2026

Service Brakes

Read full complaint

I am writing to file a formal safety complaint regarding the extreme delay in the recall remedy for my vehicle. Despite the recall being issued months ago, Ford Motor Company/Lincoln has failed to resolve this critical safety issue in a timely manner. Here are my vehicle details: Year/Make/Model: 2016 Lincoln MKX VIN [XXX] NHTSA Recall Number: 25V544 Manufacturer Recall Number: 25S87 Component Affected: Rear Flexible Brake Hoses Description of the Safety Concern: The recall notice explicitly states that a failure in the rear flexible brake hoses can lead to a loss of brake fluid, resulting in increased brake pedal travel and significantly increased stopping distances, which greatly elevates the risk of a crash. Recently, I have started experiencing a noticeable softening in the brake pedal ("increased pedal travel"), which makes driving the vehicle extremely hazardous. When I contacted my local Lincoln dealership, I was informed that they do not have the necessary parts in stock and could not provide a definitive timeline for the repair. As a consumer, I am being forced to drive a vehicle with a known, severe braking defect because the manufacturer has failed to supply the remedy parts. This is a direct threat to my life, my family’s safety, and the safety of others on the road. Furthermore, this prolonged delay is causing me significant financial hardship and stress. I urgently request NHTSA to intervene and hold Ford Motor Company accountable for expediting the parts distribution for this critical safety recall. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ODI #11744532

Mileage unknown · Jun 12, 2026

Service Brakes

My vehicle is very hard to stop . The recall was in August of2025 for my back break hoses, as of today Ford/Lincoln doesn't have the part . This is very Dangerous. I'm financing my vehicle therefore I don't have funds to repair it myself. I'm at risk of crashing and I take my kids to school daily, I'm putting my family life in …

Read full complaint

NHTSA ODI #11743642

Mileage unknown · Jun 10, 2026

Service Brakes

See attached document for complaint.

NHTSA ODI #11743209

Mileage unknown · Mar 27, 2026

Service Brakes

Unknown Still waiting for solution for possible brake failure. Not comfortable just waiting for an accident to happen while driving.

NHTSA ODI #11727413

Mileage unknown · Mar 1, 2026

Service Brakes

2 recalls, saftey notice,#25S87,25E02,first is from September 25,secons,December 25,no update or any information.

NHTSA ODI #11721263

Mileage unknown · Feb 8, 2026

Service BrakesUnknown Or Other

Read full complaint

While driving home from work during rush hour, a warning light illuminated on my dashboard and my vehicle suddenly lost braking ability. When I pressed the brake pedal, the vehicle did not slow or stop. I was forced to pull onto the shoulder of the road and pump the brake pedal extremely hard multiple times before the vehicle finally came to a stop. This occurred in heavy traffic and created an immediate and severe safety risk. The vehicle was towed to a dealership for inspection. I was informed that only a “temporary fix” could be performed, and I was required to pay approximately $500 for this repair in order to regain use of the vehicle. The vehicle has not received a permanent repair, and the dealership has taken several months without completing a permanent fix. I have also been waiting several months for reimbursement of the almost $500 paid for the temporary repair, with no resolution. I am concerned that I was charged for a temporary repair related to a serious safety failure and that continued delays in both reimbursement and permanent repair place me at ongoing risk. I am filing this complaint due to the dangerous nature of the brake failure, the lack of a permanent repair, the extended delay in resolving a critical safety issue, and the financial burden placed on me for a temporary solution.

NHTSA ODI #11716544

Mileage unknown · Dec 11, 2025

Electrical SystemForward Collision AvoidanceService BrakesCrash

Read full complaint

My car is currently under two recall notices however only one of the issues has been communicated to me of resolution. One being emissions control 25E02 and second being Recall 25S87 REAR BRAKE FLEXIBLE HOSE LEAK. Recall 1- emissions has been a problem for about 2 years now. Emissions are connected to my engine thus having my check engine light come on. My car failed an emissions test but was only 4 years old and the catalytic converters are not broken, have hole, anything leading to failed test, car repair fees and non-registered vehicle. The second recall is not being fixed, and I have had to replace my brake house, line and rear right brake twice this year. Lastly, I have collision warning however it does not work properly if at all. I was in a minor fender bender when I went to push on brakes the sound to warn me of a collision did not go off until after the crash! I am unsure of the process but if connected to my braking system it failed and if it is a preventative measure it sucks.

NHTSA ODI #11704531

Official recalls

25V544000 · Service Brakes, Hydraulic:foundation Components:hoses, Lines/piping, And Fittings

Aug 22, 2025

Ford Motor Company (Ford) is recalling certain 2016-2018 Lincoln MKX and 2015-2018 Edge vehicles. The rear brake jounce hose may rupture and leak brake fluid.

Consequence & remedy

Consequence: A brake fluid leak can extend the distance required to stop the vehicle, increasing the risk of a crash.

Remedy: Dealers will inspect and replace the brake jounce hoses and adjust brake jounce hoses with no damage present, free of charge. Interim owner letters notifying owners of the safety risk were mailed September 8, 2025. Additional letters will be sent once the remedy is available, anticipated August 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S87.

20V469000 · Service Brakes; Service Brakes, Hydraulic:foundation Components:hoses, Lines/piping, And Fittings

Aug 10, 2020

Ford Motor Company (Ford) is recalling certain 2015-2018 Ford Edge and 2016-2018 Lincoln MKX vehicles. The front brake hoses may rupture prematurely.

Consequence & remedy

Consequence: A ruptured front brake hose will cause a brake fluid leak, lengthening the distance needed to stop the vehicle, increasing the risk of a crash.

Remedy: Ford will notify owners, and dealers will replace the front brake hoses with the new hoses that have a revised braid material, free of charge. Owner notification letters were mailed on May 13, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S42.

Additional source detail variants (2)

Service Brakes

Ford Motor Company (Ford) is recalling certain 2015-2018 Ford Edge and 2016-2018 Lincoln MKX vehicles. The front brake hoses may rupture prematurely.

Consequence: A ruptured front brake hose will cause a brake fluid leak, lengthening the distance needed to stop the vehicle, increasing the risk of a crash.

Remedy: Ford will notify owners, and dealers will replace the front brake hoses with the new hoses that have a revised braid material, free of charge. Owner notification letters were mailed on May 13, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S42.

Service Brakes, Hydraulic:foundation Components:hoses, Lines/piping, And Fittings

Ford Motor Company (Ford) is recalling certain 2015-2018 Ford Edge and 2016-2018 Lincoln MKX vehicles. The front brake hoses may rupture prematurely.

Consequence: A ruptured front brake hose will cause a brake fluid leak, lengthening the distance needed to stop the vehicle, increasing the risk of a crash.

20V414000 · Air Bags; Electrical System:wiring:interior/under Dash; Seats:front Assembly:power Adjust

Jul 17, 2020

Ford Motor Company, Inc. (Ford) is recalling certain 2016-2018 Lincoln MKX and 2019-2020 Nautilus vehicles equipped with 16-way electric tilt seats. The seat cushion frame edge may contact the wire harness when the seat occupant uses the tilt function of the seat, potentially damaging one or more wires within the harness, which can result in either inadvertent deployment of the air bag or nondeployment of the air bag in the event of a crash.

Consequence & remedy

Consequence: An air bag that deploys inadvertently increases the risk of a crash. An air bag that does not deploy in the event of a crash increases the risk of injury.

Remedy: Ford will notify owners, and dealers will install protective flocking tape onto the exposed edge of the 16-way seat cushion frames, and inspect the wire harness for damage, and repair or replace it as needed, free of charge. This recall began August 12, 2020. Owners may contact Ford/Lincoln customer service at 1-866-436-7332. Ford's number for this recall is 20S37.

Additional source detail variants (3)

Seats:front Assembly:power Adjust

Consequence: An air bag that deploys inadvertently increases the risk of a crash. An air bag that does not deploy in the event of a crash increases the risk of injury.

Remedy: Ford will notify owners, and dealers will install protective flocking tape onto the exposed edge of the 16-way seat cushion frames, and inspect the wire harness for damage, and repair or replace it as needed, free of charge. This recall began August 12, 2020. Owners may contact Ford/Lincoln customer service at 1-866-436-7332. Ford's number for this recall is 20S37.

Air Bags

Consequence: An air bag that deploys inadvertently increases the risk of a crash. An air bag that does not deploy in the event of a crash increases the risk of injury.

Electrical System:wiring:interior/under Dash

Consequence: An air bag that deploys inadvertently increases the risk of a crash. An air bag that does not deploy in the event of a crash increases the risk of injury.

19V809000 · Electrical SYSTEM:12V/24V/48V Battery:cables

Nov 12, 2019

Ford Motor Company (Ford) is recalling certain 2016-2017 Lincoln MKX vehicles equipped with 3.7L engines. The battery positive cable harness may contact the transmission shifter cable bracket resulting in a short circuit.

Consequence & remedy

Consequence: An electrical short increases the risk of a fire.

Remedy: Ford will notify owners, and dealers will remove the battery harness clips and elbow guide, and install a wire channel shield and protective sleeve to the battery cable harness, free of charge. Interim notices informing owners of the safety risk were mailed on December 2, 2019. Owners will receive a second notice when the remedy becomes available, currently expected to be the end of April 2020. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S41.

19V632000 · Steering:electric Power Assist System

Aug 29, 2019

Ford Motor Company (Ford) is recalling certain 2013-2016 Ford Fusion and Lincoln MKZ, 2015-2016 Ford Edge, and 2016 Lincoln MKX vehicles originally sold, or currently registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, and Wisconsin. Road salt or other contaminants may corrode the electric power steering gear motor attachment bolts.

Consequence & remedy

Consequence: If the bolts corrode, the steering gear motor may detach from the gear housing resulting in a loss of power steering assist, requiring a greater steering effort, especially at lower speeds, and increasing the risk of a crash.

Remedy: Ford will notify owners, and dealers will replace the steering gear motor bolts and apply a wax sealer. If any of the steering gear motor attachment bolts are broken or missing, a new steering gear will be installed in the vehicle. These repairs will be performed free of charge. The recall began October 18, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S26.

17V123000 · Air Bags:frontal:driver Side:inflator Module

Feb 27, 2017

Ford Motor Company (Ford) is recalling certain 2016-2017 Ford Edge and Lincoln MKX vehicles and 2017 Lincoln Continental vehicles. In the event of a crash, the driver's frontal air bag may not fully inflate or the air bag cushion may detach from the air bag module. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection."

Consequence & remedy

Consequence: During deployment, if the air bag does not fully inflate or the cushion detaches, there is an increased risk of injury in the event of a crash.

Remedy: Ford will notify owners, and dealers will replace the driver frontal air bag module, free of charge. The recall began June 16, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17C02.

16V343000 · Child Seat:tether: Connector/clip

May 24, 2016

Ford Motor Company (Ford) is recalling certain model year 2016 Lincoln MKX vehicles manufactured September 24, 2015. An incorrect seat back trim cover was installed on the affected vehicles, blocking the child seat tether anchors in the second row center seating position. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 225, "Child restraint anchorage systems."

Consequence & remedy

Consequence: An improperly anchored child seat can increase the risk of injury in a crash.

Remedy: Ford will notify owners, and dealers will replace the seat back trim cover and tether cover bezel on the second row, free of charge. The recall began on June 16, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C09.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

Air Bags:frontal:passenger Side:inflator Module