TL* THE CONTACT OWNS A 2016 LINCOLN MKX. THE CONTACT NOTICED AN ABNORMAL TOXIC ODOR OF STRONG FUMES INSIDE THE VEHICLE WEEKS AFTER PURCHASING THE VEHICLE. THE VEHICLE WAS TAKEN TO MORE THAN TWO DEALERS (FIRST DEALER: WALLACE LINCOLN, 5555 US-1, FORT PIERCE, FL 34982, (772) 461-6060 AND SECOND DEALER: PARADISE FORD, 1360 W KING S…
Read full complaint
TL* THE CONTACT OWNS A 2016 LINCOLN MKX. THE CONTACT NOTICED AN ABNORMAL TOXIC ODOR OF STRONG FUMES INSIDE THE VEHICLE WEEKS AFTER PURCHASING THE VEHICLE. THE VEHICLE WAS TAKEN TO MORE THAN TWO DEALERS (FIRST DEALER: WALLACE LINCOLN, 5555 US-1, FORT PIERCE, FL 34982, (772) 461-6060 AND SECOND DEALER: PARADISE FORD, 1360 W KING ST, COCOA, FL 32922, (321) 632-2222), BUT THE ODOR ISSUE WAS NOT RESOLVED. THE CONTACT CONTINUED TO INHALE THE TOXIC FUMES. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE AND DID NOT PROVIDE ANY FURTHER DIAGNOSTIC TESTING. THE CONTACT RECEIVED NO SOLUTION AND WAS UNCERTAIN OF A REPAIR REMEDY. THE APPROXIMATE FAILURE MILEAGE WAS LESS THAN 250. UPDATED 08/24/17*LJ *JS
NHTSA ODI #11000401
5,107 miles · Apr 22, 2017
Electrical SystemEngineFire
AFTER START AND SHORT DRIVE INCLUDING A LEFT THAN RIGHT TURN. AT STOP SIGN, VEHICLE DASHBOARD LIT UP WITH SAFETY WARNINGS, STARTED SHAKING, LOST POWER, AND STARTED ON FIRE. SMOKE BEGAN IN DRIVERS SIDE ENGINE COMPARTMENT AND ENGULFED WHOLE ENGINE. VEHICLE WAS SERVICED TWO DAYS PRIOR.
NHTSA ODI #10979889
12,000 miles · Sep 19, 2016
Electrical SystemEngine
ON 3 SEPARATE OCCASIONS (MOST RECENT ON 9/16/16) POWER TO VEHICLE SIMPLY CUTS OUT - ON TWO OCCASIONS IT HAS OCCURRED AT HIGH SPEEDS ON BUSY INTERSTATE WITH HEAVY TRAFFIC. EXTREME DANGER, AS UNABLE TO TIMELY PULL TO SIDE OF THE ROAD CAUSING TRAFFIC JAMS AND POTENTIAL ACCIDENTS/REAR-ENDS. SELLING DEALER HAS BEEN UNABLE TO RESOLV…
Read full complaint
ON 3 SEPARATE OCCASIONS (MOST RECENT ON 9/16/16) POWER TO VEHICLE SIMPLY CUTS OUT - ON TWO OCCASIONS IT HAS OCCURRED AT HIGH SPEEDS ON BUSY INTERSTATE WITH HEAVY TRAFFIC. EXTREME DANGER, AS UNABLE TO TIMELY PULL TO SIDE OF THE ROAD CAUSING TRAFFIC JAMS AND POTENTIAL ACCIDENTS/REAR-ENDS. SELLING DEALER HAS BEEN UNABLE TO RESOLVE OR FIX PROBLEM.
NHTSA ODI #10907519
365 miles · Sep 8, 2016
Electrical SystemExterior Lighting
TL* THE CONTACT OWNS A 2016 LINCOLN MKX. THE CONTACT STATED THAT THE WARNING INDICATOR ILLUMINATED TO CHECK THE HEAD LAMP SYSTEM AND "SEE MANUAL ON THE DISPLAY" DISPLAYED ON THE MESSAGE BOARD. THE VEHICLE WAS TAKEN TO THE DEALER TWICE, BUT THEY WERE UNABLE TO REPLICATE AND DIAGNOSE THE FAILURE. THE DEALER REPROGRAMMED THE HCM, B…
Read full complaint
TL* THE CONTACT OWNS A 2016 LINCOLN MKX. THE CONTACT STATED THAT THE WARNING INDICATOR ILLUMINATED TO CHECK THE HEAD LAMP SYSTEM AND "SEE MANUAL ON THE DISPLAY" DISPLAYED ON THE MESSAGE BOARD. THE VEHICLE WAS TAKEN TO THE DEALER TWICE, BUT THEY WERE UNABLE TO REPLICATE AND DIAGNOSE THE FAILURE. THE DEALER REPROGRAMMED THE HCM, BUT THE WARNING INDICATOR FLASHED SEVERAL TIMES AGAIN MONTHS LATER. THE VEHICLE WAS TAKEN BACK TO THE DEALER A THIRD TIME FOR FURTHER TESTING AGAIN AND THEY LATER TOLD THE CONTACT TO PICK UP THE VEHICLE. THE VEHICLE WAS NOT DIAGNOSED. THE MANUFACTURER WAS NOTIFIED. THE CONTACT WAS WAITING FOR A RESPONSE FROM THE MANUFACTURER. THE APPROXIMATE FAILURE MILEAGE WAS 365.
NHTSA ODI #10904708
4,500 miles · Sep 8, 2016
Electrical System
TL* THE CONTACT OWNS A 2016 LINCOLN MKX. WHILE DRIVING APPROXIMATELY 55 MPH, THE VEHICLE LOST POWER AND FAILED TO RESTART. THE ALL WHEEL DRIVE INDICATOR ILLUMINATED. THE CONTACT CALLED FOR ROADSIDE ASSISTANCE, BUT THE VEHICLE RESTARTED BEFORE THEY ARRIVED. THE FAILURE RECURRED ON THE WAY TO THE DEALER, BUT THE VEHICLE RESTARTED.…
Read full complaint
TL* THE CONTACT OWNS A 2016 LINCOLN MKX. WHILE DRIVING APPROXIMATELY 55 MPH, THE VEHICLE LOST POWER AND FAILED TO RESTART. THE ALL WHEEL DRIVE INDICATOR ILLUMINATED. THE CONTACT CALLED FOR ROADSIDE ASSISTANCE, BUT THE VEHICLE RESTARTED BEFORE THEY ARRIVED. THE FAILURE RECURRED ON THE WAY TO THE DEALER, BUT THE VEHICLE RESTARTED. THE DEALER WAS UNABLE TO DUPLICATE THE FAILURE. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND INFORMED THE CONTACT TO DOCUMENT WHAT HAPPENED. THE FAILURE MILEAGE WAS 4,500.
NHTSA ODI #10904632
6,700 miles · Jul 22, 2016
Electrical SystemEngineFuel/propulsion System
2016 LINCOLN MKX HAS STALLED NUMEROUS TIMES. WE LEFT HOME AND HAD DRIVEN ABOUT A MILE IN OUR SUBDIVISION WHEN I SLOWED FOR AND STOPPED AT STOP SIGN. THE ENGINE SHUDDERED AND SHOOK, ENGINE REVOLUTIONS SLOWED DOWN. SPED UP, SLOWED DOWN AND ENGINE QUIT. THE MESSAGE, "FULL ACCESSORY POWER ACTIVE' DISPLAYED ON THE DASH AND MY WIFE GO…
Read full complaint
2016 LINCOLN MKX HAS STALLED NUMEROUS TIMES. WE LEFT HOME AND HAD DRIVEN ABOUT A MILE IN OUR SUBDIVISION WHEN I SLOWED FOR AND STOPPED AT STOP SIGN. THE ENGINE SHUDDERED AND SHOOK, ENGINE REVOLUTIONS SLOWED DOWN. SPED UP, SLOWED DOWN AND ENGINE QUIT. THE MESSAGE, "FULL ACCESSORY POWER ACTIVE' DISPLAYED ON THE DASH AND MY WIFE GOT A PAD AND PENCIL AND COPIED IT DOWN FOR ME. THIS WAS THE SECOND TIME THAT HAS HAPPENED AND EVIDENTLY WAS THE SAME MESSAGE DISPLAYED WHEN THE ENGINE QUIT WHILE WE WERE ON VACATION IN NEW ORLEANS. CHECKED THE INTERNET AND FOUND SEVERAL INSTANCES TO THIS HAPPENING DUE TO A COMPUTER GLITCH. FORD HAS KNOWN ABOUT THIS PROBLEM FOR SOME TIME. DO WE HAVE TO GET KILLED BEFORE FORD CORRECTS THEIR FAULTY COMPUTERS? TO MAKE MATTERS WORSE, I HAD SCHEDULED AND APPOINTMENT WITH MY DEALER, DROVE 31 MILES, ONLY TO FIND OUT THE SERVICE DEPARTMENT HAD NO KNOWLEDGE OF MY APPOINTMENT. SPOKE WITH THE SERVICE MANAGER ON 21 JULY AND HE TOLD ME HE WOULD SEND ME AN EMAIL BY THE END OF THE WEEK. WELL THE END OF THE WEEK IS HERE AND I'VE NOT HEARD ANYTHING YET. IT IS MY UNDERSTANDING THAT THE MKX IS A GLORIFIED FORD EDGE AND THAT THE STALLING PROBLEMS WERE ON-GOING FOR SEVERAL YEARS.
NHTSA ODI #10887833
290 miles · Apr 3, 2016
Electrical System
SYNC 3 NAVIGATION UNIT FAULTED OUT FREEZING SOME OF THE CONTROLS ON THE CENTER STACK. PHONE FUNCTIONS (INCLUDING 911 ASSIST BECAME INOPERATIVE. HAS HAPPENED SEVERAL TIMES WITH VARYING DEGREES OF SEVERITY. UNIT WILL AUTOMATICALLY RESET WHEN CAR IS TURNED OFF AND DOOR OPENED AND CLOSED. LINCOLN'S POSITION: NO FAULT CODE, NO PR…
Read full complaint
SYNC 3 NAVIGATION UNIT FAULTED OUT FREEZING SOME OF THE CONTROLS ON THE CENTER STACK. PHONE FUNCTIONS (INCLUDING 911 ASSIST BECAME INOPERATIVE. HAS HAPPENED SEVERAL TIMES WITH VARYING DEGREES OF SEVERITY. UNIT WILL AUTOMATICALLY RESET WHEN CAR IS TURNED OFF AND DOOR OPENED AND CLOSED. LINCOLN'S POSITION: NO FAULT CODE, NO PROBLEM.
Ford Motor Company (Ford) is recalling certain 2016-2018 Lincoln MKX and 2015-2018 Edge vehicles. The rear brake jounce hose may rupture and leak brake fluid.
Consequence & remedy
Consequence: A brake fluid leak can extend the distance required to stop the vehicle, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the brake jounce hoses and adjust brake jounce hoses with no damage present, free of charge. Interim owner letters notifying owners of the safety risk were mailed September 8, 2025. Additional letters will be sent once the remedy is available, anticipated August 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S87.
Ford Motor Company (Ford) is recalling certain 2015-2018 Ford Edge and 2016-2018 Lincoln MKX vehicles. The front brake hoses may rupture prematurely.
Consequence & remedy
Consequence: A ruptured front brake hose will cause a brake fluid leak, lengthening the distance needed to stop the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will replace the front brake hoses with the new hoses that have a revised braid material, free of charge. Owner notification letters were mailed on May 13, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S42.
Additional source detail variants (2)
Service Brakes
Ford Motor Company (Ford) is recalling certain 2015-2018 Ford Edge and 2016-2018 Lincoln MKX vehicles. The front brake hoses may rupture prematurely.
Consequence: A ruptured front brake hose will cause a brake fluid leak, lengthening the distance needed to stop the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will replace the front brake hoses with the new hoses that have a revised braid material, free of charge. Owner notification letters were mailed on May 13, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S42.
Service Brakes, Hydraulic:foundation Components:hoses, Lines/piping, And Fittings
Ford Motor Company (Ford) is recalling certain 2015-2018 Ford Edge and 2016-2018 Lincoln MKX vehicles. The front brake hoses may rupture prematurely.
Consequence: A ruptured front brake hose will cause a brake fluid leak, lengthening the distance needed to stop the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will replace the front brake hoses with the new hoses that have a revised braid material, free of charge. Owner notification letters were mailed on May 13, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S42.
Ford Motor Company, Inc. (Ford) is recalling certain 2016-2018 Lincoln MKX and 2019-2020 Nautilus vehicles equipped with 16-way electric tilt seats. The seat cushion frame edge may contact the wire harness when the seat occupant uses the tilt function of the seat, potentially damaging one or more wires within the harness, which can result in either inadvertent deployment of the air bag or nondeployment of the air bag in the event of a crash.
Consequence & remedy
Consequence: An air bag that deploys inadvertently increases the risk of a crash. An air bag that does not deploy in the event of a crash increases the risk of injury.
Remedy: Ford will notify owners, and dealers will install protective flocking tape onto the exposed edge of the 16-way seat cushion frames, and inspect the wire harness for damage, and repair or replace it as needed, free of charge. This recall began August 12, 2020. Owners may contact Ford/Lincoln customer service at 1-866-436-7332. Ford's number for this recall is 20S37.
Additional source detail variants (3)
Seats:front Assembly:power Adjust
Ford Motor Company, Inc. (Ford) is recalling certain 2016-2018 Lincoln MKX and 2019-2020 Nautilus vehicles equipped with 16-way electric tilt seats. The seat cushion frame edge may contact the wire harness when the seat occupant uses the tilt function of the seat, potentially damaging one or more wires within the harness, which can result in either inadvertent deployment of the air bag or nondeployment of the air bag in the event of a crash.
Consequence: An air bag that deploys inadvertently increases the risk of a crash. An air bag that does not deploy in the event of a crash increases the risk of injury.
Remedy: Ford will notify owners, and dealers will install protective flocking tape onto the exposed edge of the 16-way seat cushion frames, and inspect the wire harness for damage, and repair or replace it as needed, free of charge. This recall began August 12, 2020. Owners may contact Ford/Lincoln customer service at 1-866-436-7332. Ford's number for this recall is 20S37.
Air Bags
Ford Motor Company, Inc. (Ford) is recalling certain 2016-2018 Lincoln MKX and 2019-2020 Nautilus vehicles equipped with 16-way electric tilt seats. The seat cushion frame edge may contact the wire harness when the seat occupant uses the tilt function of the seat, potentially damaging one or more wires within the harness, which can result in either inadvertent deployment of the air bag or nondeployment of the air bag in the event of a crash.
Consequence: An air bag that deploys inadvertently increases the risk of a crash. An air bag that does not deploy in the event of a crash increases the risk of injury.
Remedy: Ford will notify owners, and dealers will install protective flocking tape onto the exposed edge of the 16-way seat cushion frames, and inspect the wire harness for damage, and repair or replace it as needed, free of charge. This recall began August 12, 2020. Owners may contact Ford/Lincoln customer service at 1-866-436-7332. Ford's number for this recall is 20S37.
Electrical System:wiring:interior/under Dash
Ford Motor Company, Inc. (Ford) is recalling certain 2016-2018 Lincoln MKX and 2019-2020 Nautilus vehicles equipped with 16-way electric tilt seats. The seat cushion frame edge may contact the wire harness when the seat occupant uses the tilt function of the seat, potentially damaging one or more wires within the harness, which can result in either inadvertent deployment of the air bag or nondeployment of the air bag in the event of a crash.
Consequence: An air bag that deploys inadvertently increases the risk of a crash. An air bag that does not deploy in the event of a crash increases the risk of injury.
Remedy: Ford will notify owners, and dealers will install protective flocking tape onto the exposed edge of the 16-way seat cushion frames, and inspect the wire harness for damage, and repair or replace it as needed, free of charge. This recall began August 12, 2020. Owners may contact Ford/Lincoln customer service at 1-866-436-7332. Ford's number for this recall is 20S37.
Ford Motor Company (Ford) is recalling certain 2016-2017 Lincoln MKX vehicles equipped with 3.7L engines. The battery positive cable harness may contact the transmission shifter cable bracket resulting in a short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Ford will notify owners, and dealers will remove the battery harness clips and elbow guide, and install a wire channel shield and protective sleeve to the battery cable harness, free of charge. Interim notices informing owners of the safety risk were mailed on December 2, 2019. Owners will receive a second notice when the remedy becomes available, currently expected to be the end of April 2020. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S41.
Ford Motor Company (Ford) is recalling certain 2013-2016 Ford Fusion and Lincoln MKZ, 2015-2016 Ford Edge, and 2016 Lincoln MKX vehicles originally sold, or currently registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, and Wisconsin. Road salt or other contaminants may corrode the electric power steering gear motor attachment bolts.
Consequence & remedy
Consequence: If the bolts corrode, the steering gear motor may detach from the gear housing resulting in a loss of power steering assist, requiring a greater steering effort, especially at lower speeds, and increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will replace the steering gear motor bolts and apply a wax sealer. If any of the steering gear motor attachment bolts are broken or missing, a new steering gear will be installed in the vehicle. These repairs will be performed free of charge. The recall began October 18, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S26.
Ford Motor Company (Ford) is recalling certain 2016-2017 Ford Edge and Lincoln MKX vehicles and 2017 Lincoln Continental vehicles. In the event of a crash, the driver's frontal air bag may not fully inflate or the air bag cushion may detach from the air bag module. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection."
Consequence & remedy
Consequence: During deployment, if the air bag does not fully inflate or the cushion detaches, there is an increased risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will replace the driver frontal air bag module, free of charge. The recall began June 16, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17C02.
Ford Motor Company (Ford) is recalling certain model year 2016 Lincoln MKX vehicles manufactured September 24, 2015. An incorrect seat back trim cover was installed on the affected vehicles, blocking the child seat tether anchors in the second row center seating position. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 225, "Child restraint anchorage systems."
Consequence & remedy
Consequence: An improperly anchored child seat can increase the risk of injury in a crash.
Remedy: Ford will notify owners, and dealers will replace the seat back trim cover and tether cover bezel on the second row, free of charge. The recall began on June 16, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C09.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
2016 Lincoln Mkx Problems, Complaints & Recalls | Skip That Year
Illustration