← New search

2018 Jeep Cherokee

Owner reports · Recalls · Investigations

More warning signs than most Cherokee years

Owner complaints for the 2018 Jeep Cherokee are substantially higher than the model-year median of 113.

About this comparison →

When problems were reported

Mileage at the reported incident

359 reports with mileage · 324 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Power Train. Review the 292 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 190 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 155 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

11 crash reports5 fire reports3 injury reports

What owners actually said

683 reports
20,103 miles · Dec 27, 2019
Power Train

I TURNED MY JEEP ON, PUT IT INTO DRIVE AND THE SCREEN SAYS SERVICE SHIFTER. ALL LIGHTS ON SHORTER ARE ON.

NHTSA ODI #11291531

30,000 miles · Dec 26, 2019
Power Train

WHILE DRIVING AND STATIONARY THE SERVICE SHIFTER LIGHT ILLUMINATES ON THE DASH AND ALL THE LIGHTS ON THE FLOOR SHIFTER ILLUMINATE ALL GEAR POSITIONS. ALSO, AT LOW SPEED, WHEN ADDING POWER, THE TRANSMISSION HAS A "BUMP" AS IT TRIES TO SHIFT INTO THE NEXT GEAR. MAKES IT JERK/CLUNK INTO GEAR.

NHTSA ODI #11291396

47,000 miles · Dec 22, 2019
Power Train

SERVICE SHIFTER APPEARS ON SCREEN, ALL SELECTIONS ON SHIFTER LIGHT UP RED. 40,000 MILES. HUNDREDS OF OTHERS WITH THE SAME PROBLEM ON THE FORUMS. VEHICLE STATIONARY. JUST STARTED UP. TURN OFF AND RESTART- IT GOES AWAY

NHTSA ODI #11290694

34,000 miles · Dec 20, 2019
Engine

MAKING A RIGHT TURN, ENGINE SHUT OFF NO POWER, LIGHTS STATED I MUST BE IN PARK TO SHIFT WARNING LIGHTS. THE JEEP WOULD NOT START. I HAD EXPERIENCED NO PRIOR ISSUES BEFORE THIS HAPPENED. I CALLED MY HUSBAND WHO ARRIVED AND DROVE IT HOME. I CALLED THE DEALERSHIP AND THEY BASICALLY TOLD ME THIS WAS A KNOWN ISSUE WITH THIS MOTOR AND…

Read full complaint

MAKING A RIGHT TURN, ENGINE SHUT OFF NO POWER, LIGHTS STATED I MUST BE IN PARK TO SHIFT WARNING LIGHTS. THE JEEP WOULD NOT START. I HAD EXPERIENCED NO PRIOR ISSUES BEFORE THIS HAPPENED. I CALLED MY HUSBAND WHO ARRIVED AND DROVE IT HOME. I CALLED THE DEALERSHIP AND THEY BASICALLY TOLD ME THIS WAS A KNOWN ISSUE WITH THIS MOTOR AND TO CHECK THE OIL. UPON CHECKING THE OIL THERE WAS VERY LITTLE ON THE DIPSTICK. ONCE AGAIN I CONTACTED THE DEALERSHIP AND WAS TOLD I BASICALLY NEED TO KEEP A CHECK ON THE OIL. THIS IS A SAFETY HAZARD!

NHTSA ODI #11290266

22,425 miles · Dec 18, 2019
Electrical SystemEngineUnknown Or Other

"SERVICE SHIFTER" LIGHTS UP.

NHTSA ODI #11289985

50,000 miles · Dec 18, 2019
Unknown Or Other

SERVICE SHIFTER LIGHT CAME ON AND ALL THE LIGHTS ON SHIFTER CAME ON AND WON'T GO OFF. P R N D, ETC. WAS DRIVING DOWN INTERSTATE, TOOK EXIT AND WHEN I WAS COMING TO STOP AT STOP SIGN A WARNING BEEP SOUNDED AND LIGHTS CAME ON SHIFTER AND DASH SAYING SERVICE SHIFTER. CANNOT FIND ANYTHING ABOUT SERVICING A SHIFTER.

NHTSA ODI #11289949

24,834 miles · Dec 14, 2019
Unknown Or Other

2018 CHEROKEE 24,834 MILES. PUT IN REVERSE WHILE BACKING OUT OF DRIVE. SERVICE SHIFTER LIGHT APPEARED AND ALL GEAR LIGHT INDICATORS ILLUMINATED RED.

NHTSA ODI #11289011

38,000 miles · Dec 12, 2019
Unknown Or Other

WHILE DRIVING ON THE HIGHWAY, A "SERVICE SHIFTER" NOTICE COMES UP ON MY SH. ALL THE LIGHTS NEXT TO EACH GEAR LIGHT UP ON MY SHIFTER. THE NOTICE WON'T GO AWAY UNLESS I TURN THE CAR OFF FOR AT LEAST 5 MINUTES. IT COMES BACK ANYWHERE BETWEEN IMMEDIATELY AND 10 DAYS LATER. USUALLY DAILY. DEALER SAYS THEY'VE NEVER HEARD OF IT BUT THE…

Read full complaint

WHILE DRIVING ON THE HIGHWAY, A "SERVICE SHIFTER" NOTICE COMES UP ON MY SH. ALL THE LIGHTS NEXT TO EACH GEAR LIGHT UP ON MY SHIFTER. THE NOTICE WON'T GO AWAY UNLESS I TURN THE CAR OFF FOR AT LEAST 5 MINUTES. IT COMES BACK ANYWHERE BETWEEN IMMEDIATELY AND 10 DAYS LATER. USUALLY DAILY. DEALER SAYS THEY'VE NEVER HEARD OF IT BUT THERE ARE REPORTS ALL OVER THE INTERNET. SOME WAY THE CAR WILL EVENTUALLY STALL OR YOU CANNOT PUT IT IN PARK.

NHTSA ODI #11288697

53,000 miles · Dec 10, 2019
Power Train

THREE TIMES OVER A PERIOD OF FOUR DAYS WHILE DRIVING ALL LIGHTS ON THE GEAR SHIFT (PARK, NEUTRAL, REVERSE, AND DRIVING) LIT UP AND A MESSAGE CAME ON THE DASHBOARD THAT READ "SERVICE SHIFTER". EACH TIME THE VEHICLE WAS IN MOTION, TWICE WHILE ON CITY STREETS AND ONCE WHILE ENTRY A HIGHWAY. ALL THREE TIMES THE VEHICLE WAS TURNING…

Read full complaint

THREE TIMES OVER A PERIOD OF FOUR DAYS WHILE DRIVING ALL LIGHTS ON THE GEAR SHIFT (PARK, NEUTRAL, REVERSE, AND DRIVING) LIT UP AND A MESSAGE CAME ON THE DASHBOARD THAT READ "SERVICE SHIFTER". EACH TIME THE VEHICLE WAS IN MOTION, TWICE WHILE ON CITY STREETS AND ONCE WHILE ENTRY A HIGHWAY. ALL THREE TIMES THE VEHICLE WAS TURNING LEFT.

NHTSA ODI #11288158

56,000 miles · Dec 9, 2019
Electrical SystemEngineUnknown Or Other

THE CAR STOPPED WORKING WHILE IN MOTION IN THE MIDDLE OF THE STREET WHILE TURNING TOWARDS MY APARTMENT COMPLEX. I HAD MY DAUGHTER INSIDE THE CAR WITH ME AND I WAS AFRAID CARS WILL COME SINCE I WAS IN THE MIDDLE OF THE STREET WERE CARS PASS BY TO ENTER THE APARTMENT COMPLEX. I WAS ABLE TO PUSH THE CAR AFTER CALLING MY DAD WHO HEL…

Read full complaint

THE CAR STOPPED WORKING WHILE IN MOTION IN THE MIDDLE OF THE STREET WHILE TURNING TOWARDS MY APARTMENT COMPLEX. I HAD MY DAUGHTER INSIDE THE CAR WITH ME AND I WAS AFRAID CARS WILL COME SINCE I WAS IN THE MIDDLE OF THE STREET WERE CARS PASS BY TO ENTER THE APARTMENT COMPLEX. I WAS ABLE TO PUSH THE CAR AFTER CALLING MY DAD WHO HELPED ME TAKE IT TO A SAFE SPOT AND JUMP START THE CAR. THE CAR WORKED AFTER DOING A JUMP START AND I WAS ABLE TO PARK IT AT MY PARKING SPOT. THE NEXT DAY I WAS LEAVING TO DROP OFF MY DAUGHTER TO SCHOOL AND SAME THING HAPPENED AGAIN. I WAS INSIDE THE CAR COMING OUT (IN MOTION) AND THE CAR STOPPED SUDDENLY AND WOULDN'T TURN. I CALLED ROAD ASSISTANCE THIS TIME. THEY SENT ME A TOWING COMPANY TO TAKE IT TO THE CLOSEST JEEP DEALERSHIP. SINCE THE CAR WAS NOT ABLE TO TURN ON AT ALL, THEY WERE NOT ABLE TO TAKE IT. THEY SAID THE CAR NEED IT A FLAT BED TOW TRUCK SINCE IT DIDN'T START AT ALL. THEY WERE ABLE TO TOW THE CAR 3 DAYS LATER ON SATURDAY 12/07/19 BY A TOWING COMPANY THAT HAD A FLAT BED TOW TRUCK AND TOOK IT TO THE CLOSEST JEEP DEALERSHIP. THE CAR IS CURRENTLY AT ORLANDO DODGE JEEP DEALERSHIP AND THEY SAID THE WIN MODULE NEEDS TO BE REPLACED, THE BATTERY NEEDS TO BE RECHARGE AND GET NEW KEYS. I BOUGHT THIS CAR BRAND NEW WITH 0 MILEAGES FROM JEEP DEALERSHIP ONLY 1 YEAR AND 6 MONTHS OLD. I DECIDED TO BUY A NEW CAR IN ORDER TO AVOID RISKS LIKE THESE ONE OF BEING LEFT IN THE MIDDLE OF THE STREET/ROAD WITH MY DAUGHTER INSIDE THE CAR. THANKFULLY THIS DID NOT HAPPEN IN THE MIDDLE OF ROUTE I-4 WERE I NORMALLY DRIVE.

NHTSA ODI #11287938

Official recalls

7

25V011000 · Power Train

Apr 29, 2025

Chrysler (FCA US, LLC) is recalling certain 2017-2019 Jeep Cherokee vehicles. The power transfer unit (PTU) may become damaged and disengage the transmission and differential, resulting in a loss of drive power and/or loss of park function.

Consequence & remedy

Consequence: A loss of drive power can increase the risk of a crash. A loss of park function can cause an unintended vehicle rollaway, which can increase the risk of a crash or injury.

Remedy: Dealers will update the drivetrain control module and PTU software and replace the PTU, as necessary free of charge. Owner notification letters were mailed beginning February 19, 2026. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 01C.

18V524000 · Electrical System:wiring:front Underhood

Aug 9, 2018

Chrysler (FCA US LLC) is recalling certain 2018 Jeep Renegade, Compass and Grand Cherokee, RAM 1500 and Promaster, Fiat 500x, Dodge Journey, Challenger, Charger and Durango and Chrysler 300x vehicles, 2017-2018 Jeep Wrangler, Dodge Grand Caravan and Chrysler Town and Country vehicles and 2018-2019 Jeep Cherokee and 2018 Chrysler Pacifica and Pacifica Hybrid vehicles. The powertrain control module may be equipped with a voltage regulator chip in the circuit board that may fail, causing a stall or a no start condition.

Consequence & remedy

Consequence: A vehicle stall can increase the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the powertrain control module, free of charge. The recall began October 2, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U87.

18V494000 · Power Train:axle Assembly:axle Shaft

Jul 26, 2018

Chrysler (FCA US LLC) is recalling certain 2018 Jeep Cherokee all-wheel-drive vehicles. The bearing cage for the right front halfshaft assembly may not have been properly heat treated, possibly resulting in the bearing cage breaking and a potential halfshaft assembly failure.

Consequence & remedy

Consequence: If the halfshaft bearing cage breaks, the halfshaft may not be able to transmit engine power, causing a loss of drive or it can allow the vehicle to move while in the "Park" position. Either condition may increase the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the front right halfshaft assemblies, free of charge. The recall began September 20, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U78.

18V332000 · Electrical System:software; Electrical System:wiring; Vehicle Speed Control:cruise Control

May 17, 2018

Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

Consequence & remedy

Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

Additional source detail variants (3)

Electrical System:software

Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

Vehicle Speed Control:cruise Control

Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

Electrical System:wiring

Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

18V282000 · Fuel System, Gasoline:delivery:hoses, Lines/piping, And Fittings

May 1, 2018

Chrysler (FCA US LLC) is recalling certain 2018 Jeep Cherokee vehicles equipped with a 2.4L engine. These vehicles may have been manufactured with a fuel tube that may leak fuel into the engine compartment.

Consequence & remedy

Consequence: A fuel leak in the presence of the ignition source can increase the risk of a fire.

Remedy: Chrysler will notify owners, and dealers will inspect the fuel tube, replacing it as necessary, free of charge. The recall began May 24, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U39.

17V670000 · Engine And Engine Cooling:engine

Oct 24, 2017

Chrysler (FCA US LLC) is recalling certain 2018 Jeep Cherokee and Compass vehicles equipped with 2.4L engines. The engines may have a cracked oil pump housing that can result in oil pump failure.

Consequence & remedy

Consequence: If the oil pump fails, the engine will stall, increasing the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the oil pump, replacing it as necessary, free of charge. The recall began December 5, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T65.

17V543000 · Equipment:other:labels; Wheels:rim

Aug 31, 2017

Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."

Consequence & remedy

Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.

Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.

Additional source detail variants (2)

Equipment:other:labels

Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."

Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.

Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.

Wheels:rim

Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."

Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.

Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.