NHTSA owner reports · September 18, 2026 snapshot.
Electrical System complaints
190 reportsClear category filter56,000 miles · Dec 9, 2019
Electrical SystemEngineUnknown Or Other
THE CAR STOPPED WORKING WHILE IN MOTION IN THE MIDDLE OF THE STREET WHILE TURNING TOWARDS MY APARTMENT COMPLEX. I HAD MY DAUGHTER INSIDE THE CAR WITH ME AND I WAS AFRAID CARS WILL COME SINCE I WAS IN THE MIDDLE OF THE STREET WERE CARS PASS BY TO ENTER THE APARTMENT COMPLEX. I WAS ABLE TO PUSH THE CAR AFTER CALLING MY DAD WHO HEL…
Read full complaint
THE CAR STOPPED WORKING WHILE IN MOTION IN THE MIDDLE OF THE STREET WHILE TURNING TOWARDS MY APARTMENT COMPLEX. I HAD MY DAUGHTER INSIDE THE CAR WITH ME AND I WAS AFRAID CARS WILL COME SINCE I WAS IN THE MIDDLE OF THE STREET WERE CARS PASS BY TO ENTER THE APARTMENT COMPLEX. I WAS ABLE TO PUSH THE CAR AFTER CALLING MY DAD WHO HELPED ME TAKE IT TO A SAFE SPOT AND JUMP START THE CAR. THE CAR WORKED AFTER DOING A JUMP START AND I WAS ABLE TO PARK IT AT MY PARKING SPOT. THE NEXT DAY I WAS LEAVING TO DROP OFF MY DAUGHTER TO SCHOOL AND SAME THING HAPPENED AGAIN. I WAS INSIDE THE CAR COMING OUT (IN MOTION) AND THE CAR STOPPED SUDDENLY AND WOULDN'T TURN. I CALLED ROAD ASSISTANCE THIS TIME. THEY SENT ME A TOWING COMPANY TO TAKE IT TO THE CLOSEST JEEP DEALERSHIP. SINCE THE CAR WAS NOT ABLE TO TURN ON AT ALL, THEY WERE NOT ABLE TO TAKE IT. THEY SAID THE CAR NEED IT A FLAT BED TOW TRUCK SINCE IT DIDN'T START AT ALL. THEY WERE ABLE TO TOW THE CAR 3 DAYS LATER ON SATURDAY 12/07/19 BY A TOWING COMPANY THAT HAD A FLAT BED TOW TRUCK AND TOOK IT TO THE CLOSEST JEEP DEALERSHIP. THE CAR IS CURRENTLY AT ORLANDO DODGE JEEP DEALERSHIP AND THEY SAID THE WIN MODULE NEEDS TO BE REPLACED, THE BATTERY NEEDS TO BE RECHARGE AND GET NEW KEYS. I BOUGHT THIS CAR BRAND NEW WITH 0 MILEAGES FROM JEEP DEALERSHIP ONLY 1 YEAR AND 6 MONTHS OLD. I DECIDED TO BUY A NEW CAR IN ORDER TO AVOID RISKS LIKE THESE ONE OF BEING LEFT IN THE MIDDLE OF THE STREET/ROAD WITH MY DAUGHTER INSIDE THE CAR. THANKFULLY THIS DID NOT HAPPEN IN THE MIDDLE OF ROUTE I-4 WERE I NORMALLY DRIVE.
NHTSA ODI #11287938
19,900 miles · Dec 6, 2019
Electrical SystemEngineFuel/propulsion System
VEHICLE HAS STALLED APPROXIMATELY 10 TIMES IN THE LAST 2 WEEKS. SOME ON THE STREETS AND 3 TIMES ON THE FREEWAY. HALF THE TIME I WAS WITH MY CHILDREN. YOU HAVE TO PUT IT BACK ON PARK, WAIT ABOUT 10-15 SECONDS, THEN SWITCH IT ON AN OFF THREE TIMES BEFORE IT STARTS AGAIN.
NHTSA ODI #11287402
52,295 miles · Dec 2, 2019
Electrical SystemUnknown Or Other
ON 11/24/19 @ APPROXIMATELY 5:30PM LIGHTS ILLUMINATED SAYING SERVICE SERVICE SHIFT ADJUSTOR. THEN ON 11/29/19 WENT TO DRIVE THE CAR MADE IT A BLOCK FROM THE HOUSE AND CAR TURNED OFF. DRIVING IT TO THE DEALERSHIP TODAY (12/2) WHICH IS APPROXIMATELY HALF MILE AWAY DIED TWICE. AFTER A FEW SECONDS IT STARTS AGAIN.
NHTSA ODI #11286516
58,000 miles · Nov 28, 2019
Electrical SystemPower Train
WARNING APPEARS ABOUT THE SHIFTER AND ALL THE LIGHTS COME ON. I READ A FORUM WHERE DOZENS OF PEOPLE ARE HAVING THIS PROBLEM AND HAVING TO REPLACE THEIR HARNESS AND WIRING KIT. I'VE ALSO BEEN TOLD THERE'S SOMETHING ABOUT THIS MODELS CRUISE CONTROL BUT WHEN I SEARCH ON HERE NOTHING COMES UP.
NHTSA ODI #11282787
43,250 miles · Nov 25, 2019
Electrical System
WHEN ATTEMPTING TO START THE VEHICLE, THE ELECTRICAL SYSTEM WILL SHUT COMPLETELY DOWN AND A CREATE A NO START SITUATION. IT MAY TAKE SEVERAL ATTEMPTS WITH THE SAME RESULT, A PARTIAL ROTATION OF THE ENGINE BEFORE THE SYSTEM RESETS. I CHECKED THE BATTERY VOLTAGE WHICH WAS READING ABOUT 11.5 VOLTS, WHEN I ATTEMPTED TO JUMP THE VEHI…
Read full complaint
WHEN ATTEMPTING TO START THE VEHICLE, THE ELECTRICAL SYSTEM WILL SHUT COMPLETELY DOWN AND A CREATE A NO START SITUATION. IT MAY TAKE SEVERAL ATTEMPTS WITH THE SAME RESULT, A PARTIAL ROTATION OF THE ENGINE BEFORE THE SYSTEM RESETS. I CHECKED THE BATTERY VOLTAGE WHICH WAS READING ABOUT 11.5 VOLTS, WHEN I ATTEMPTED TO JUMP THE VEHICLE, I GOT THE SAME RESULT. IT FINALLY STARTED AFTER MORE THAN 5 ATTEMPTS WITH JUMPER CABLES CONNECTED. MOST OTHER TIMES, IT WILL START AFTER ABOUT 2 ATTEMPTS WITHOUT ATTACHING ANY JUMPER CABLES. THIS IS ALSO AFTER THE AUTO START STOP SYSTEM STOPPED WORKING A COUPLE OF WEEKS BACK STATING THE BATTERY IS CHARGING EVEN THOUGH IT WAS FULLY CHARGED.
NHTSA ODI #11282109
34,300 miles · Nov 16, 2019
Electrical SystemPower TrainService Brakes
ELECTRICAL WARNING SYSTEM CAN NOT BE REMEDIED. EMERGENCY BRAKE SYSTEM IS MALFUNCTIONING AND SETTING WHEN CAR IS IN DRIVE. ELECTRICAL SYSTEM COMPLETELY WENT DEAD ON THE FREEWAY CAUSING THE CAR TO STALL, WHEN CAR WAS RESTARTED AND NURSED OFF OF THE FREEWAY THE ELECTRICAL SYSTEM COMPLETELY WENT DEAD, THE TRANSMISSION LOCKED UP PR…
Read full complaint
ELECTRICAL WARNING SYSTEM CAN NOT BE REMEDIED. EMERGENCY BRAKE SYSTEM IS MALFUNCTIONING AND SETTING WHEN CAR IS IN DRIVE. ELECTRICAL SYSTEM COMPLETELY WENT DEAD ON THE FREEWAY CAUSING THE CAR TO STALL, WHEN CAR WAS RESTARTED AND NURSED OFF OF THE FREEWAY THE ELECTRICAL SYSTEM COMPLETELY WENT DEAD, THE TRANSMISSION LOCKED UP PREVENTING THE TOW COMPANY FROM LOADING THE CAR ONTO THE TOW TRUCK, THE CAR WAS MANUALLY MANIPULATED TO RELEASE THE SYSTEM INTO NEUTRAL. THE CARS ELECTRONIC DASH BOARD COMPLETELY GOES DEAD WHILE ON THE FREEWAY. THE CAR HAS BEEN IN 3 DEALERSHIPS OVER MORE THAN 1 MONTH, THE DEALERSHIPS CLAIM THEY HAVE REPLACED COMPUTER COMPONENTS, CAN'T FIND ANYTHING WRONG, OR 'JIGGLE THE WIRES'. THE CARS WARRANTY IS NEARLY UP, AND WE HAVE BEEN PRESSURED TO BUY AN EXTENDED WARRANTY. THE DEALERSHIP HAS PROVIDED US WITH A RENTAL CAR, AND CLAIMED TO HAVE FIXED THE PROBLEM, THAT IS WHEN THE CARS ELECTRICAL SYSTEM FAILED ON THE FREEWAY. THE CAR IS A COMPLETE HAZARD. MY HUSBAND HAS THE REPAIR RECORDS ON FILE.
NHTSA ODI #11280560
28,000 miles · Nov 14, 2019
Electrical System
WHILE DRIVING SERVICE SHIFTER WARNING MESSAGE TURNS ON FOR NO REASON. RESETS WITH POWER CYCLE.
NHTSA ODI #11279996
12,200 miles · Oct 20, 2019
Electrical SystemSteeringUnknown Or Other
WE PURCHASED A USED 2018 JEEP CHEROKEE LATITUDE (LESS THAN 13,000 MILES) FROM A DEALERSHIP IN COLORADO SPRINGS ON 10/17. ON THE WAY HOME, ABOUT 100 MILES, THE STOP /START WARNING LIGHT AND BATTERY LIGHT WENT ON ABOUT 8 MILES FROM HOME GOING APPROX. 50 MPH. WE DECIDED TO GET IT HOME. AT THE BOTTOM OF THE DRIVEWAY, WE PLACED THE …
Read full complaint
WE PURCHASED A USED 2018 JEEP CHEROKEE LATITUDE (LESS THAN 13,000 MILES) FROM A DEALERSHIP IN COLORADO SPRINGS ON 10/17. ON THE WAY HOME, ABOUT 100 MILES, THE STOP /START WARNING LIGHT AND BATTERY LIGHT WENT ON ABOUT 8 MILES FROM HOME GOING APPROX. 50 MPH. WE DECIDED TO GET IT HOME. AT THE BOTTOM OF THE DRIVEWAY, WE PLACED THE CAR IN REVERSE AND NOTICED THAT POWER STEERING WAS NOT WORKING. WE TURNED OFF THE VEHICLE AND AT RESTART, THE WARNING LIGHTS WERE RESET. WE NOTIFIED THE DEALERSHIP IMMEDIATELY AND THEY RECOMMENDED CHANGING OUT BATTERY. WE DROVE ABOUT 15 MILES TO AN AUTO PARTS STORE AND BOUGHT THE BEST BATTERY THEY HAD FOR THAT VEHICLE. WE DID NOT USE THE JEEP FOR THE NEXT DAY (FRIDAY). SATURDAY 10/19 WE DROVE IT DOWN TO DENVER (ABOUT 60 MILES) WITH NO PROBLEM. ON THE WAY HOME, AGAIN THE STOP /START WARNING LIGHT AND BATTERY LIGHT WENT ON GOING APPROX. 60 MPH. WE DROVE TO A PARKING LOT AND MADE A TURN INTO A PARKING SPOT. AT THAT POINT POWER STEERING WAS OPERABLE. I PLACED THE CAR IN PARK AND THEN IN REVERSE AND THEN NOTICED NO POWER STEERING, I PLACED THE CAR IN DRIVE AND AGAIN NO POWER STEERING. WE STOPPED AND RESTARTED THE VEHICLE AND THE WARNING LIGHTS WERE RESET. ABOUT 2 MINUTES LATER WHILE DRIVING, I NOTICED THAT THE DRIVER'S SIDE SEAT WARMER AND REAR DEFROST HAD BOTH BEEN SWITCHED ON AUTOMATICALLY.
NHTSA ODI #11269737
30,000 miles · Oct 19, 2019
Electrical SystemEnginePower Train
SERVICE SHIFTER LIGHT ALWAYS ON IN MOTION AND IN PARK. BURNS 1 QT OF OIL EVERY 2000 MILES VEHICLES JERKS WHEN TRYING TO ACCELERATE IN MOTION
NHTSA ODI #11269508
40,029 miles · Oct 17, 2019
Electrical SystemElectronic Stability Control (esc)Unknown Or Other
WHILE DRIVING MY 2018 JEEP CHEROKEE A MESSAGE APPEARED ON THE DASH 'SERVICE SHIFTER' ALL LIGHTS ON THE SHIFTER THEN LIGHT UP RED THE 'PRNDL' THIS HAS HAPPENED MULTIPLE TIMES. THE VEHICLE SEEMS TO NOT SHIFT GEARS PROPERLY WHEN THIS HAPPENS. IT HAS BEEN CHECKED BY THE DEALER AND THE SHIFTER/ WIRING HARNESS NEED TO BE REPLACED. I W…
Read full complaint
WHILE DRIVING MY 2018 JEEP CHEROKEE A MESSAGE APPEARED ON THE DASH 'SERVICE SHIFTER' ALL LIGHTS ON THE SHIFTER THEN LIGHT UP RED THE 'PRNDL' THIS HAS HAPPENED MULTIPLE TIMES. THE VEHICLE SEEMS TO NOT SHIFT GEARS PROPERLY WHEN THIS HAPPENS. IT HAS BEEN CHECKED BY THE DEALER AND THE SHIFTER/ WIRING HARNESS NEED TO BE REPLACED. I WAS INFORMED THIS IS AN ONGOING ISSUE WITH MOST JEEPS IN THE LAST FEW YEARS AND NO RECALL HAS YET BEEN MADE, I HAVE ONLY OWNED THIS VEHICLE FOR 7 MONTHS AND AM VERY DISAPPOINTED THUS FAR. THIS BEING AN ONGOING ISSUE THAT JEEP IS AWARE OF I FEEL THAT SOME ACTION SHOULD BE MADE FOR THE CUSTOMER. I AM A LOYAL JEEP CUSTOMER BUT AFTER THIS ISSUE NOT BEING RESOLVED FOR YEARS I MAY NOT CONTINUE TO BE A LOYAL CUSTOMER AND GO ELSEWHERE TO PURCHASE MY NEXT VEHICLE. THIS FIRST OCCURRED ON SEPTEMBER 25,2019 AND HAS HAPPENED MULTIPLE TIMES SINCE THE FIRST OCCURRENCE.
NHTSA ODI #11269119
Official recalls
7Apr 29, 2025
Chrysler (FCA US, LLC) is recalling certain 2017-2019 Jeep Cherokee vehicles. The power transfer unit (PTU) may become damaged and disengage the transmission and differential, resulting in a loss of drive power and/or loss of park function.
Consequence & remedy
Consequence: A loss of drive power can increase the risk of a crash. A loss of park function can cause an unintended vehicle rollaway, which can increase the risk of a crash or injury.
Remedy: Dealers will update the drivetrain control module and PTU software and replace the PTU, as necessary free of charge. Owner notification letters were mailed beginning February 19, 2026. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 01C.
Aug 9, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Renegade, Compass and Grand Cherokee, RAM 1500 and Promaster, Fiat 500x, Dodge Journey, Challenger, Charger and Durango and Chrysler 300x vehicles, 2017-2018 Jeep Wrangler, Dodge Grand Caravan and Chrysler Town and Country vehicles and 2018-2019 Jeep Cherokee and 2018 Chrysler Pacifica and Pacifica Hybrid vehicles. The powertrain control module may be equipped with a voltage regulator chip in the circuit board that may fail, causing a stall or a no start condition.
Consequence & remedy
Consequence: A vehicle stall can increase the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the powertrain control module, free of charge. The recall began October 2, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U87.
Jul 26, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Cherokee all-wheel-drive vehicles. The bearing cage for the right front halfshaft assembly may not have been properly heat treated, possibly resulting in the bearing cage breaking and a potential halfshaft assembly failure.
Consequence & remedy
Consequence: If the halfshaft bearing cage breaks, the halfshaft may not be able to transmit engine power, causing a loss of drive or it can allow the vehicle to move while in the "Park" position. Either condition may increase the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the front right halfshaft assemblies, free of charge. The recall began September 20, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U78.
May 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence & remedy
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Additional source detail variants (3)
Electrical System:software
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Vehicle Speed Control:cruise Control
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Electrical System:wiring
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
May 1, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Cherokee vehicles equipped with a 2.4L engine. These vehicles may have been manufactured with a fuel tube that may leak fuel into the engine compartment.
Consequence & remedy
Consequence: A fuel leak in the presence of the ignition source can increase the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will inspect the fuel tube, replacing it as necessary, free of charge. The recall began May 24, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U39.
Oct 24, 2017
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Cherokee and Compass vehicles equipped with 2.4L engines. The engines may have a cracked oil pump housing that can result in oil pump failure.
Consequence & remedy
Consequence: If the oil pump fails, the engine will stall, increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the oil pump, replacing it as necessary, free of charge. The recall began December 5, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T65.
Aug 31, 2017
Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.
Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.
Additional source detail variants (2)
Equipment:other:labels
Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.
Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.
Wheels:rim
Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.
Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration