Service shifter indicator lights on console & display. Comes on while driving & scared to drive due to not knowing if it will fail & cause an accident and/or fatality
2017 Jeep Cherokee
Owner reports · Recalls · Investigations
More warning signs than most Cherokee years
Owner complaints for the 2017 Jeep Cherokee are substantially higher than the model-year median of 113.
About this comparison →How this year compares
Owner complaints by model year
Compare all Cherokee years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
834 reports with mileage · 499 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 646 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 342 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 258 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
1,333 reportsSERVICE SHIFTER - I RESEARCHED THE PROPBLEM AND APPRENTLY THERE IS A FAULTY ERROR WITH A LOT OF JEEP CHEROKEE IN REGARDS OF THIS MATTER PLEASE INVISTIGATE. THANK YOU
Service shifter warning. Car stalled twice. It has 45 k miles only. Won't start on first try.
My service shifter light came on and all the lights on the shifter console came on (PRND21). At first, I could turn the car off to reset it. This was dangerous because I had to pull over wherever I was. As time has gone on it pretty much stays on. My car has 33000 miles on it but is past the 3-year mark. I took it to the de…
Read full complaint
My service shifter light came on and all the lights on the shifter console came on (PRND21). At first, I could turn the car off to reset it. This was dangerous because I had to pull over wherever I was. As time has gone on it pretty much stays on. My car has 33000 miles on it but is past the 3-year mark. I took it to the dealership and they told me the previous years had this problem but was recalled. It cost me $500.00 to replace a plastic bezel. I have saved all dealership repair paperwork. The dealership confirmed this is a very common problem.
My car completely cut off while driving it on 2 separate occasions on 6/14 & 6/29. I was going 15-20 mph and slowing down for a stop light both times. The car just cut off without any warning. Once I put it in park I was able to start it back up without a problem. I took it to get serviced and the shop said there were multiple f…
Read full complaint
My car completely cut off while driving it on 2 separate occasions on 6/14 & 6/29. I was going 15-20 mph and slowing down for a stop light both times. The car just cut off without any warning. Once I put it in park I was able to start it back up without a problem. I took it to get serviced and the shop said there were multiple faulty computer codes so they reset the system. They advised me to call the dealership to see if there is a recall. I called a dealership and there is not a recall. They told me to bring it in so they could do a diagnostic test and check the fuel system. The earliest appointment at 2 dealerships I called is a month out and if I scheduled a drop-off appointment that could be done in about 7-10 days.
While driving the Service Shifter prompt came on and all the lights on the gear box turned red. The safety risk when this prompt came on is huge as you are driving and trying not to panic as you don't know if the car will stall or stop suddenly. MANY other people with Jeeps have experienced this problem. There should be a recall…
Read full complaint
While driving the Service Shifter prompt came on and all the lights on the gear box turned red. The safety risk when this prompt came on is huge as you are driving and trying not to panic as you don't know if the car will stall or stop suddenly. MANY other people with Jeeps have experienced this problem. There should be a recall for this issue. This vehicle has under 25,000 miles. I went to the dealership and was informed the parts are not covered under warranty. It was confirmed the Bezel and Wire Harness will have to be replaced which the dealership did on 6/24/2021. The vehicle was only inspected by the dealership. No other warnings or dashboard messages prior to 6/23/2021.
I received an engine shutoff signal which disabled the car immediately without prior warning. It was due to the protection signal for low oil. The vehicle had a oil change 5,000 miles prior with synthetic oil. Over the course of 5,000 miles it "burned" the oil to the point of low level. Upon discovery, I noted many customer comp…
Read full complaint
I received an engine shutoff signal which disabled the car immediately without prior warning. It was due to the protection signal for low oil. The vehicle had a oil change 5,000 miles prior with synthetic oil. Over the course of 5,000 miles it "burned" the oil to the point of low level. Upon discovery, I noted many customer complaints (online) of this issue. There was no prior warning to the low oil level (no low pressure light or indicator.) I purchased this vehicle for my daughter and had she been driving on a busy highway, it would have disabled her car without any power to safely navigate this from the road, probably leading to a major accident. A newer vehicle with no mechanical issues does not "burn" oil excessively, this is a major engine issue. Some oil loss is understood and normal (in older cars), this newer vehicle used over 3 quarts of oil in the span of one oil change. Had I known about this issue, I would have been vigilant in monitoring this issue. Not knowing about this issue led to a very unsafe shutdown of the vehicle.
The vehicle didn’t have any warning lights or messages on dashboard. Someone ran a red light and hit my car while we were both going over 40mph and my airbags didn’t deploy but there’s did.. my car got towed as it wasn’t drivable anymore and was told the airbags where suppose to deploy but they didn’t.
The Jeep is used as a flat tow vehicle with our 2004 Monaco RV. On June 8, we left Ducket Mill Campground in Dawsonville GA to return home to Cincinnati OH. The vehicle was attached to the RV with the Blue Ox Flat Tow system. The four tires on the Jeep were checked and were all rolling. We followed the instructions in the man…
Read full complaint
The Jeep is used as a flat tow vehicle with our 2004 Monaco RV. On June 8, we left Ducket Mill Campground in Dawsonville GA to return home to Cincinnati OH. The vehicle was attached to the RV with the Blue Ox Flat Tow system. The four tires on the Jeep were checked and were all rolling. We followed the instructions in the manual, which were also the instructions given to us by the RV dealer who did the installation. One hour and a half after we left, the Jeep started smoking. A truck driver who passed our vehicle pulled off the side of the road yelled that the parking brake was on and needed to be turned off. Upon checking, there were two flat, chewed up tires. We were towed to a tire dealer in Ellijay GA to have repaired. We have one of the tires. That night, we found a Jeep salesman from 2017 on YouTube explaining the parking brake had to be disengaged to make sure there were no problems in flat towing. This was the first we had heard of this problem. We checked in the manual, and the only mention was that the electronic parking brake can be disengaged. No other warning. When we got home, we had the Jeep into the dealer. They could find nothing wrong with the parking brake system. They DROVE the car, but dd not flat tow it. The person at the tire store showed us how the tire was worn and torn up in a small area, probably caused by the parking brake engaging. Since we were not in the car and the car worked fine for an hour and 1/2 (not to mention the entire way down from Cincinnati to Dawsonville), we believe the parking brake engaged by itself as we drove through the mountains.
My daughter was driving her car. It started "jerking". She pulled into a parking lot because she was worried. Her granddad went to pick it up and it drove fine for him. He said the parking brake was on- she did NOT put the parking brake on. I drove it down the street the next day- it jerked then also- and then stopped in the mid…
Read full complaint
My daughter was driving her car. It started "jerking". She pulled into a parking lot because she was worried. Her granddad went to pick it up and it drove fine for him. He said the parking brake was on- she did NOT put the parking brake on. I drove it down the street the next day- it jerked then also- and then stopped in the middle of the road. I was able to get it started back up and pull into my driveway. The next day my husband got it towed to a repair shop. It wouldn't work at all! The shop says it needs the transmission rebuilt or a new one. I feel my daughter's safety was at risk, because she is a newly turned 16 year old driver. If she had been driving it when it completely stopped it could have been bad. There were no warning lamps or messages beforehand- except that the parking brake was on- when it was not.
Official recalls
625V011000 · Power Train
Apr 29, 2025
Chrysler (FCA US, LLC) is recalling certain 2017-2019 Jeep Cherokee vehicles. The power transfer unit (PTU) may become damaged and disengage the transmission and differential, resulting in a loss of drive power and/or loss of park function.
Consequence & remedy
Consequence: A loss of drive power can increase the risk of a crash. A loss of park function can cause an unintended vehicle rollaway, which can increase the risk of a crash or injury.
Remedy: Dealers will update the drivetrain control module and PTU software and replace the PTU, as necessary free of charge. Owner notification letters were mailed beginning February 19, 2026. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 01C.
23V302000 · Power Train:automatic Transmission
Apr 27, 2023
Chrysler (FCA US, LLC) is recalling certain 2016-2017 Jeep Cherokee vehicles. The power transfer unit (PTU) may become damaged and disengage the transmission and differential, resulting in a loss of drive power or loss of park function.
Consequence & remedy
Consequence: A loss of drive power can increase the risk of a crash. A loss of park function can cause an unintended vehicle rollaway which can increase the risk of a crash or injury.
Remedy: FCA US LLC will notify owners, and dealers will perform a software update, free of charge. Owner notification letters were mailed May 11, 2023. Owners may contact FCA USA LLC customer service at 1-800-853-1403. FCA's number for this recall is 45A. This recall expands previous recall number 20V-343.
20V343000 · Power Train:automatic Transmission; Power Train:driveline:differential Unit
Jun 11, 2020
Chrysler (FCA US LLC) is recalling certain 2014-2017 Jeep Cherokee vehicles equipped with a two-speed Power Transfer Unit (PTU). Relative movement in the Power Transfer Unit (PTU) between the differential input splines and the transmission output shaft may cause some input spline teeth to wear off, which may eventually cause a loss of engagement between the transmission and the differential inside the PTU. If this occurs, power cannot be transferred between the front wheels and the transmission which results in a loss of drive while the vehicle is in motion and a loss of the Park function while stationary.
Consequence & remedy
Consequence: A loss of drive can cause a vehicle crash without prior warning. A loss of the Park function can cause unintended vehicle rollaway which can increase the risk of a crash or injury.
Remedy: FCA US LLC will notify owners, and dealers will perform a software update that will maintain vehicle propulsion by engaging rear wheel drive and prevent rolling in Park by activating the electronic parking brake if a failed input spline occurs. This recall began July 14, 2020. Owners may contact FCA USA LLC customer service at 1-800-853-1403. FCA's number for this recall is W47.
Additional source detail variants (2)
Power Train:driveline:differential Unit
Chrysler (FCA US LLC) is recalling certain 2014-2017 Jeep Cherokee vehicles equipped with a two-speed Power Transfer Unit (PTU). Relative movement in the Power Transfer Unit (PTU) between the differential input splines and the transmission output shaft may cause some input spline teeth to wear off, which may eventually cause a loss of engagement between the transmission and the differential inside the PTU. If this occurs, power cannot be transferred between the front wheels and the transmission which results in a loss of drive while the vehicle is in motion and a loss of the Park function while stationary.
Consequence: A loss of drive can cause a vehicle crash without prior warning. A loss of the Park function can cause unintended vehicle rollaway which can increase the risk of a crash or injury.
Remedy: FCA US LLC will notify owners, and dealers will perform a software update that will maintain vehicle propulsion by engaging rear wheel drive and prevent rolling in Park by activating the electronic parking brake if a failed input spline occurs. This recall began July 14, 2020. Owners may contact FCA USA LLC customer service at 1-800-853-1403. FCA's number for this recall is W47.
Power Train:automatic Transmission
Chrysler (FCA US LLC) is recalling certain 2014-2017 Jeep Cherokee vehicles equipped with a two-speed Power Transfer Unit (PTU). Relative movement in the Power Transfer Unit (PTU) between the differential input splines and the transmission output shaft may cause some input spline teeth to wear off, which may eventually cause a loss of engagement between the transmission and the differential inside the PTU. If this occurs, power cannot be transferred between the front wheels and the transmission which results in a loss of drive while the vehicle is in motion and a loss of the Park function while stationary.
Consequence: A loss of drive can cause a vehicle crash without prior warning. A loss of the Park function can cause unintended vehicle rollaway which can increase the risk of a crash or injury.
Remedy: FCA US LLC will notify owners, and dealers will perform a software update that will maintain vehicle propulsion by engaging rear wheel drive and prevent rolling in Park by activating the electronic parking brake if a failed input spline occurs. This recall began July 14, 2020. Owners may contact FCA USA LLC customer service at 1-800-853-1403. FCA's number for this recall is W47.
18V332000 · Electrical System:software; Electrical System:wiring; Vehicle Speed Control:cruise Control
May 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence & remedy
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Additional source detail variants (3)
Electrical System:software
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Vehicle Speed Control:cruise Control
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Electrical System:wiring
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
17V543000 · Equipment:other:labels; Wheels:rim
Aug 31, 2017
Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.
Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.
Additional source detail variants (2)
Equipment:other:labels
Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.
Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.
Wheels:rim
Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.
Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.
16V799000 · Air Bags:knee Bolster
Nov 2, 2016
Chrysler (FCA US LLC) is recalling certain model year 2017 Jeep Cherokee vehicles manufactured October 13, 2016, to October 17, 2016. Improper welds on the driver's knee air bag inflator may prevent the air bag from properly inflating.
Consequence & remedy
Consequence: If the driver's knee air bag does not properly inflate, there is an increased risk of injury in the event of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the driver's knee air bag module, free of charge. The recall began November 9, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S84.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration