IllustrationSTEERING AND FRONT SUSPENSION WANDERS SUDDENLY AND ALMOST UNCONTROLLABLY WHEN VEHICLE TRANSITIONS FROM A SMOOTH TO SEMI-ROUGH ROAD SURFACE AT 50-65 MILES PER HOUR. *TR
2007 Infiniti M35
Owner reports · Recalls · Investigations
More warning signs than most M35 years
Owner complaints for the 2007 Infiniti M35 are substantially higher than the model-year median of 60.
About this comparison →How this year compares
Owner complaints by model year
Compare all M35 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
120–25K
1325–50K
2050–75K
1575–100K
27100–150K
3150K+
90 reports with mileage · 65 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 45 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Seats. Review the 40 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Steering. Review the 26 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
5 crash reports0 fire reports5 injury reports
Steering complaints
26 reportsIN NOVEMBER 2007 I PURCHASED A NEW 2007 INFINITI M35. SINCE THAT TIME, WHENEVER I DRIVE OVER ROUGH SURFACES, THE CAR JERKS TO THE LEFT AND RIGHT, REQUIRING A VERY FIRM GRIP ON THE STEERING WHEEL AT ALL TIMES. THE LOCAL INFINITI SERVICE CONSULTANT SAID THIS WAS A COMMON PROBLEM FOR THIS TYPE VEHICLE. AFTER SOME RESEARCH, I DIS…
Read full complaint
IN NOVEMBER 2007 I PURCHASED A NEW 2007 INFINITI M35. SINCE THAT TIME, WHENEVER I DRIVE OVER ROUGH SURFACES, THE CAR JERKS TO THE LEFT AND RIGHT, REQUIRING A VERY FIRM GRIP ON THE STEERING WHEEL AT ALL TIMES. THE LOCAL INFINITI SERVICE CONSULTANT SAID THIS WAS A COMMON PROBLEM FOR THIS TYPE VEHICLE. AFTER SOME RESEARCH, I DISCOVERED THERE ARE OTHER 2007 M35 OWNERS WITH THE SAME PROBLEM. THEY DEFINE THEIR PROBLEM AS 'TRAMLINING' AND I BELIEVE MY ISSUES ARE THE SAME AND THIS PROBLEM PRESENTS SERIOUS SAFETY ISSUES. PLEASE LET ME KNOW IF OR WHEN INFINITI PROVIDES SOMETHING TO CORRECT THIS PROBLEM. *TR
1 - PROBLEM HAS OCCURRED SINCE I PURCHASED THE CAR NEW IN FEB 2007.1 - WHEN I DRIVE ON ROADS WITH TRUCK RUTS THE CAR PULLS ONE SIDE OR ANOTHER, OFTEN FORCING ME INTO THE OTHER TRAFFIC LANE (IF I DO NOT CATCH IT SOON ENOUGH). 3 - NO RECALL TO FIX THIS PROBLEM TO DATE. I DO NOT HAVE AN ALIGNMENT PROBLEM NOR A TIRE PROBLEM. *TR
CAR HAS VERY IRREGULAR STEERING ESPECIALLY ON GROOVED PAVEMENT. PULLS SHARPLY IN EITHER DIRECTION FROM TIME TO TIME. I BELIEVE THIS IS CALLED TRAMLINING. I HAD A 2006INFINITI M35X SEDAN WHICH HAD THIS PROBLEM AND I NOW HAVE A 2007 MODEL OF THE SAME CAR AND THE PROBLEM IS EVEN WORSE. MY WIFE REFUSES TO DRIVE THE CAR THINKING IT I…
Read full complaint
CAR HAS VERY IRREGULAR STEERING ESPECIALLY ON GROOVED PAVEMENT. PULLS SHARPLY IN EITHER DIRECTION FROM TIME TO TIME. I BELIEVE THIS IS CALLED TRAMLINING. I HAD A 2006INFINITI M35X SEDAN WHICH HAD THIS PROBLEM AND I NOW HAVE A 2007 MODEL OF THE SAME CAR AND THE PROBLEM IS EVEN WORSE. MY WIFE REFUSES TO DRIVE THE CAR THINKING IT IS UNSAFE. I HAVE NEW TIRES ON THE CAR. *TR
I OWN A 2007 INFINITI M35X AND IT PULLS OR IT HAS TRAMLINING ISSUES. THE CAR PULLS WILDLY TO THE RIGHT OR LEFT INDISCRIMINATE ON VARIOUS ROADS. THE CAR FEELS LIKE IT IS GOING TO LOOSE CONTROL AND GO INTO THE DITCH OR ONE COMING TRAFFIC! SOMETHING IS WRONG WITH THE TIRES, STEERING RACK OR BOTH. RECALL IS IN ORDER. *TR
ON MILDLY RUTTED HIGHWAY SURFACES, SUCH AS I-5 AND I405, VEHICLE JERKS TO THE LEFT AND RIGHT, REQUIRING AGGRESSIVE STEERING WHEEL MANAGEMENT TO KEEP THE CAR IN THE PROPER LANE OF TRAVEL. ON HEAVILY WORN SURFACES, LIKE I-90 IN SPOKANE, THE CAR WILL JERK HARD ENOUGH TO THE LEFT AND RIGHT TO SWERVE INTO THE NEXT LANE ON EITHER SID…
Read full complaint
ON MILDLY RUTTED HIGHWAY SURFACES, SUCH AS I-5 AND I405, VEHICLE JERKS TO THE LEFT AND RIGHT, REQUIRING AGGRESSIVE STEERING WHEEL MANAGEMENT TO KEEP THE CAR IN THE PROPER LANE OF TRAVEL. ON HEAVILY WORN SURFACES, LIKE I-90 IN SPOKANE, THE CAR WILL JERK HARD ENOUGH TO THE LEFT AND RIGHT TO SWERVE INTO THE NEXT LANE ON EITHER SIDE. DEALER SAYS THIS IS A COMMON COMPLAINT ON M35X (ALL WHEEL DRIVE) ONLY. WAS ADVISED BY INFINITI DEALER TO INCREASE TIRE AIR PRESSURE TO 37PSI FRONT AND 33PSI REAR. THIS HELPED BUT NOT SUBSTATIONALLY THIS IS A DANGEROUS VEHICLE! NO ACCIDENT, YET! THERE NEEDS TO BE A DESIGN CHANGE BEFORE I GET KILLED OF KILL SOMEONE ELSE. *TR
Official recalls
420V008000 · Air Bags:frontal:passenger Side:inflator Module
Jan 9, 2020
Nissan North America, Inc. (Nissan) is recalling certain 2001-2003 Maxima, 2002-2006 Sentra, 2002-2004 Pathfinder, 2007-2011 Versa Sedan and Versa Hatchback, 2001-2004 Infiniti I30 and I35, 2002-2003 Inifiniti QX4, 2003-2008 Infiniti FX35 and FX45 and 2006-2010 M35 and M45 vehicles. The vehicles are equipped with non-desiccated, frontal passenger air bag inflators containing phase stabilized ammonium nitrate (PSAN) propellant that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the front passenger air bag inflators with alternate desiccated inflators, free of charge. The recall began February 12, 2020. Owners may contact Nissan customer service at 888-737-9511 or Infiniti customer service at 888-810-3715.
17V028000 · Air Bags:frontal:passenger Side:inflator Module
Jan 10, 2017
Nissan North America, Inc. (Nissan) is recalling certain 2012 Nissan Versa hatchbacks originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan) and the U.S. Virgin Islands, or "Zone A". Additionally, if not included in "Zone A" above, Nissan is recalling certain 2009-2010 Infiniti M35 and M45 and 2009 Nissan Versa sedans and hatchbacks originally sold, or ever registered, in Arizona, Arkansas, Delaware, the District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B". Additionally, if not included in "Zone A" or "Zone B" above, Nissan is recalling certain 2005-2008 Infiniti FX35 and FX45, 2006-2010 Infiniti M35 and M45, and 2007-2008 Nissan Versa vehicles originally sold, or ever registered, in Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the front passenger air bag inflators, free of charge. The recall began on June 8, 2017. Owners will receive a second notice when remedy parts become available. Owners may contact Nissan customer service at 1-800-647-7261.
16V349000 · Air Bags:frontal:passenger Side:inflator Module
May 24, 2016
Nissan North America, Inc. (Nissan) is recalling certain model year 2003-2008 Infiniti FX35 and FX45, 2003-2004 Infiniti I35, 2006-2010 Infiniti M35 and M45, and 2007-2011 Nissan Versa vehicles, originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Nissan is recalling certain model year 2005-2008 Infiniti FX35 and FX45, 2003-2004 Infiniti I35, 2006-2008 Infiniti M35 and M45, and 2007-2008 Nissan Versa vehicles, originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Nissan is recalling certain model year 2003-2004 Infiniti I35 vehicles originally sold, or registered, in Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began December 21, 2017. All owners should receive a second notice by May 15, 2017. Owners may contact Nissan customer service at 1-800-647-7261.
13V430000 · Vehicle Speed Control:accelerator Pedal
Sep 26, 2013
Nissan North America, Inc. (Nissan) is recalling certain model year 2006-2010 Infiniti M35 and M45 vehicles manufactured April 4, 2004, through October 5, 2010. Over time, the accelerator pedal sensor signal may deteriorate resulting in the output of an incorrect signal causing the engine to go into fail-safe (limp home) mode.
Consequence & remedy
Consequence: In this fail-safe mode, throttle valve deposits may cause the engine to stall when the vehicle is coming to a stop or at idle, increasing the risk of a crash.
Remedy: Nissan will notify owners, and dealers will replace the accelerator pedal assembly and reprogram the engine control module, free of charge. The recall is expected to begin during November 2013. Owners may contact Nissan at 1-800-647-7261.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.