IllustrationWHEN I DRIVE IN THE RAIN AND GO THROUGH STANDING WATER THE STEERING COLUMN FREEZES MAKING IT VIRTUALLY IMPOSSIBLE TO MOVE.
2004 Hyundai Sonata
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2004 Hyundai Sonata do not stand out strongly from the model-year median of 161.
About this comparison →How this year compares
Owner complaints by model year
Compare all Sonata years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
190–25K
1825–50K
2850–75K
2875–100K
45100–150K
17150K+
155 reports with mileage · 47 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Suspension. Review the 56 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 47 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 46 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
22 crash reports2 fire reports23 injury reports
What owners actually said
202 reportsMY FOOT SLIDE OFF THE BREAK, AND HIT MY VAN IN THE BACK BUMPER IN MY DRIVEWAY AND TWO WEEKS LATER MY AIR BAG LIGHT CAME ON AND NEVER WENT OFF. AT MY HOME, NO REPORTS, OR DAMAGE OTHER THEM CUT ON MY BUMPER DUE TO THE HAUL ON THE VAN.
TL* THE CONTACT OWNS A 2004 HYUNDAI SONATA. WHILE THE VEHICLE WAS UNDERGOING ROUTINE SERVICE, THE TECHNICIAN NOTICED THAT UNDERNEATH THE FRONT OF THE VEHICLE WAS SEVERE CORROSION AND PERFORATION THAT NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE VIN WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 09V124000 (SUSPENSION). TH…
Read full complaint
TL* THE CONTACT OWNS A 2004 HYUNDAI SONATA. WHILE THE VEHICLE WAS UNDERGOING ROUTINE SERVICE, THE TECHNICIAN NOTICED THAT UNDERNEATH THE FRONT OF THE VEHICLE WAS SEVERE CORROSION AND PERFORATION THAT NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE VIN WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 09V124000 (SUSPENSION). THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 143,000.
TL* THE CONTACT OWNS A 2004 HYUNDAI SONATA. THE CONTACT STATED THAT THE VEHICLE HAD SEVERE RUST ON THE SUBFRAME. THE VIN WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 09V124000 (SUSPENSION). AFTER CONTACTING THE DEALER AND THE MANUFACTURER ON MULTIPLE OCCASIONS, THE CONTACT WAS INFORMED THAT THE REMEDY NEEDED TO REPAIR THE VEHICLE …
Read full complaint
TL* THE CONTACT OWNS A 2004 HYUNDAI SONATA. THE CONTACT STATED THAT THE VEHICLE HAD SEVERE RUST ON THE SUBFRAME. THE VIN WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 09V124000 (SUSPENSION). AFTER CONTACTING THE DEALER AND THE MANUFACTURER ON MULTIPLE OCCASIONS, THE CONTACT WAS INFORMED THAT THE REMEDY NEEDED TO REPAIR THE VEHICLE HAD NOT YET BEEN DETERMINED. THE CONTACT INDICATED THAT THE MANUFACTURER TOOK TOO LONG TO PROVIDE THE REMEDY. THE CONTACT EXPERIENCED THE FAILURE LISTED IN THE RECALL. THE FAILURE MILEAGE WAS 75,000. PARTS DISTRIBUTION DISCONNECT. *TR
THIS IS MY SECOND ATTEMPT SUBMITTING THE SAME COMPLAINT. THE HYUNDAI CORP HAS NOT FIXED MY CAR NOR GIVEN ME A LOANER NOR CONTACTED ME AND IT'S BEEN 3 MONTHS.
FRONT LOWER CONTROL ARM BROKE DUE TO RUST WHILE BEING DRIVEN. PULLED OFF THE ROAD AND CALLED TOW TRUCK. OPERATOR TOLD ME TO LOOK UP SONATA RECALLS BECAUSE IT LOOKED LIKE ONE. IT WAS RECALL # 09V124000. CALLED LOCAL DEALERSHIP 6 TIMES IN TWO DAYS ALWAYS GOING TO ANSWERING MACHINE. THIRD DAY DROVE TO DEALERSHIP. THEY TOLD ME TO BR…
Read full complaint
FRONT LOWER CONTROL ARM BROKE DUE TO RUST WHILE BEING DRIVEN. PULLED OFF THE ROAD AND CALLED TOW TRUCK. OPERATOR TOLD ME TO LOOK UP SONATA RECALLS BECAUSE IT LOOKED LIKE ONE. IT WAS RECALL # 09V124000. CALLED LOCAL DEALERSHIP 6 TIMES IN TWO DAYS ALWAYS GOING TO ANSWERING MACHINE. THIRD DAY DROVE TO DEALERSHIP. THEY TOLD ME TO BRING IT IN AND THEY WOULD LOOK AT IT. TOW GUY SAID EVERY TIME IT IT WAS MOVED MORE DAMAGE WOULD BE DONE. HE DIDN'T WANT THE RESPONSIBILITY. DEALERSHIP WOULDN'T PICK IT UP. TOW GUY CALLED ANOTHER DEALERSHIP AND HE BROUGHT IT THERE (8/20/16) FIVE DAYS AFTER THE BREAKDOWN. AFTER 5 DAYS SECOND DEALERSHIP SAID IT WAS A RECALL ITEM AND SAID TO CALL HYUNDAI AMERICA. BEGAN DISCUSSIONS WITH HYUNDAI AMERICA- MANY CALLS- AND AFTER OVER 60 DAYS THEY DECIDED IT WAS BETWEEN THE DEALERSHIP AND SOME OTHER DEPARTMENT OF HYUNDAI AMERICA AND THEY COULDN'T DO ANYTHING. DEALERSHIP GAVE ME ANOTHER # TO CALL BUT THAT # HAD NO KNOWLEDGE OF MY CASE. THE EXPENSE OF BEING WITHOUT THE CAR HAS BEEN QUITE DRAINING. CASE # WITH HYUNDAI AMERICA IS 9566309. I WOULD LIKE THE CAR COMPLETELY REPAIRED BUT CAN'T GET ANYONE TO DO ANYTHING. THANKS
10-01-2016 AIR BAG LIGHT CAME ON,WHILE STATIONARY AND STAYED ON WHILE DRIVING.
TL* THE CONTACT OWNS A 2004 HYUNDAI SONATA. WHILE DRIVING 10 MPH, SUBFRAME FRACTURED. THE FAILURE CAUSED THE FRONT AXLE TO FRACTURE AND SEPARATE FROM THE VEHICLE. THE FRONT AXLE WAS CUT AWAY FROM THE SUBFRAME TO HAVE THE VEHICLE TOWED. THE VEHICLE WAS TOWED TO THE DEALER TO BE DIAGNOSED, BUT WAS NOT REPAIRED. THE VEHICLE WAS INC…
Read full complaint
TL* THE CONTACT OWNS A 2004 HYUNDAI SONATA. WHILE DRIVING 10 MPH, SUBFRAME FRACTURED. THE FAILURE CAUSED THE FRONT AXLE TO FRACTURE AND SEPARATE FROM THE VEHICLE. THE FRONT AXLE WAS CUT AWAY FROM THE SUBFRAME TO HAVE THE VEHICLE TOWED. THE VEHICLE WAS TOWED TO THE DEALER TO BE DIAGNOSED, BUT WAS NOT REPAIRED. THE VEHICLE WAS INCLUDED IN NHTSA CAMPAIGN NUMBER: 09V124000 (SUSPENSION). THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 164,000.
TAKATA RECALL. AIR BAG LIGHT WILL NOT GO OFF. I AM TOLD THAT IN ORDER TO CORRECT THE PROBLEM, IT WILL COST NEARLY 2300 DOLLARS SINCE THE PASSENGER SEAT MUST BE REPLACED
TL* THE CONTACT OWNS A 2004 HYUNDAI SONATA. WHILE DRIVING 55 MPH, THE VEHICLE SHOOK. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHO DIAGNOSED THAT BOTH FRONT CV AXLES WERE CORRODED. THE VEHICLE WAS NOT REPAIRED. THE CONTACT ALSO STATED THAT THE REAR PASSENGER SIDE HUB ASSEMBLY WAS BENT AND RUBBED AGAINST THE TIRE, WHICH CA…
Read full complaint
TL* THE CONTACT OWNS A 2004 HYUNDAI SONATA. WHILE DRIVING 55 MPH, THE VEHICLE SHOOK. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHO DIAGNOSED THAT BOTH FRONT CV AXLES WERE CORRODED. THE VEHICLE WAS NOT REPAIRED. THE CONTACT ALSO STATED THAT THE REAR PASSENGER SIDE HUB ASSEMBLY WAS BENT AND RUBBED AGAINST THE TIRE, WHICH CAUSED THE TIRE TO BLOW OUT. THE MANUFACTURER WAS MADE AWARE OF THE FAILURES. THE VIN WAS UNKNOWN. THE APPROXIMATE FAILURE MILEAGE WAS 150,000.
Official recalls
109V124000 · Suspension
Apr 16, 2009
HYUNDAI IS RECALLING 188,282 MY 2001-2004 SONATA AND MY 2001-2004 XG300 AND XG350 VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA. ROAD SALT APPLIED IN THESE JURISDICTIONS DURING THE WINTER MONTHS MAY RESULT IN PROGRESSIVE, INTERNAL CORROSION OF THE FRONT SUB-FRAME ON THE VEHICLES, AND MAY RESULT IN THINNING OR PERFORATION OF THE SUB-FRAME STEEL. THE CORROSION IS FREQUENTLY VISIBLE AND OFTEN DISCOVERED DURING INSPECTION OR ROUTINE MAINTENANCE, AND OWNERS MAY ALSO HEAR NOISES OR NOTICE TIRE MISALIGNMENT AND STEERING PULL. IF THESE SIGNALS ARE UNDETECTED OR UNHEEDED, THE CORROSION MAY PROGRESS AND THE FORWARD MOUNTING OF THE LOWER CONTROL ARM MAY DETACH FROM THE SUB-FRAME.
Consequence & remedy
Consequence: IF THAT HAPPENS, THE VEHICLE MAY LOSE DRIVE POWER TO THE WHEELS, AND THE FRONT WHEEL MAY MAKE CONTACT WITH THE FENDER OR WHEEL WELL, THEREBY INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL MEASURE THE THICKNESS OF THE FRONT SUB-FRAME AND INSPECT THE FRONT SUB-FRAME FOR CORROSION DAMAGE AND, IF NECESSARY, THE FRONT SUB-FRAME WILL BE REPLACED WITH A NEW SUB-FRAME THAT INCORPORATES ADDITIONAL HOLES IN THE UPPER AND LOWER PANELS. IF THE FRONT SUB-FRAME DOES NOT REQUIRE REPLACEMENT, THE DEALER WILL ADD DRAINAGE HOLES TO THE SUB-FRAME AND WILL TREAT THE SUB-FRAME WITH RUST-PROOFING MATERIAL TO STOP THE CORROSION PROCESS. THIS PROCEDURE WILL BE PERFORMED FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING APRIL 2009. OWNERS MAY CONTACT THE HYUNDAI CUSTOMER ASSISTANCE CENTER AT 1-800-633-5151.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA08016 · Front SUB-FRAME Corrosion
Opened Aug 21, 2008 · Closed Apr 20, 2009
Status: closed (inferred from source dates) · Structure; Structure:frame And Members; Suspension; Suspension:front; Suspension:front:control Arm
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Additional source detail variants (5)
Structure:frame And Members
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Structure
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Suspension:front:control Arm
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Suspension:front
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Suspension
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.