IllustrationTHE FRAME TO THE CAR HAS A HOLE RUSTED THRU THE LOWER CONTROL ARM BOLT AND IS NO LONGER DRIVABLE. THE CAR WAS STRANDED ON THE HIGHWAY AND SOMEONE COULD HAVE BEEN KILLED HYUNDAI SAYS ITS NOT COVERED UNDER THE RECALL BUT ITS THE EXACT SAME PROBLEM AS ALL THE REST. *TR
2004 Hyundai Sonata
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2004 Hyundai Sonata do not stand out strongly from the model-year median of 161.
About this comparison →How this year compares
Owner complaints by model year
Compare all Sonata years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
190–25K
1825–50K
2850–75K
2875–100K
45100–150K
17150K+
155 reports with mileage · 47 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Suspension. Review the 56 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 47 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 46 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
22 crash reports2 fire reports23 injury reports
Structure complaints
47 reportsTL* THE CONTACT OWNS A 2004 HYUNDAI SONATA. THE CONTACT STATED THAT HE DISCOVERED INTERNAL CORROSION OF THE FRONT SUB-FRAME ON THE VEHICLE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC FOR DIAGNOSIS BUT THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED BUT OFFERED NO ASSISTANCE. THE VEHICLE HAD NOT BEEN REPAIRED. T…
Read full complaint
TL* THE CONTACT OWNS A 2004 HYUNDAI SONATA. THE CONTACT STATED THAT HE DISCOVERED INTERNAL CORROSION OF THE FRONT SUB-FRAME ON THE VEHICLE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC FOR DIAGNOSIS BUT THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED BUT OFFERED NO ASSISTANCE. THE VEHICLE HAD NOT BEEN REPAIRED. THE FAILURE AND CURRENT MILEAGES WERE 124,000.
THE CHROME ON THE INSIDE DOOR HANDLES ARE CRACKING & PEELING. I HAVE CUT MY FINGER TWICE NOW ON THE SHARP EDGES. ALSO, THE PAINT IS COMING OFF THE MOLDING AROUND THE OUTSIDE DOOR HANDLE ON THE REAR DRIVER SIDE. *TR *JS
+THE INTERIOR DOOR LEVERS CHROME IS PEELING OFF CAUSING THE LEVERS TO HAVE SHARP EDGES WHICH CUT YOUR FINGERS. *TR
THE INTERNAL FLOOR ON DRIVER SIDE SHOWS OBVIOUS EROSION FROM NORMAL SALT EXPOSURE IN THE WINTER. DEALER IGNORED MY COMPLAINT OF THE EROSION WHEN I WENT TO ADDRESS ANOTHER RECALL REGARDING SALT EROSION. ME AND A FAMILY MEMBER RECEIVED CUTS ON THE FINGER FROM PEELING COVERING ON INTERIOR DOOR HANDLE. PAINT NEAR EXTERIOR HANDL…
Read full complaint
THE INTERNAL FLOOR ON DRIVER SIDE SHOWS OBVIOUS EROSION FROM NORMAL SALT EXPOSURE IN THE WINTER. DEALER IGNORED MY COMPLAINT OF THE EROSION WHEN I WENT TO ADDRESS ANOTHER RECALL REGARDING SALT EROSION. ME AND A FAMILY MEMBER RECEIVED CUTS ON THE FINGER FROM PEELING COVERING ON INTERIOR DOOR HANDLE. PAINT NEAR EXTERIOR HANDLES SCRATCHES EASILY AND EVENTUALLY REVEALS THE COLOR OF THE SECOND LAYER OF PAINT WHICH IS A DRASTICALLY DIFFERENT COLOR FROM THE CAR'S EXTERIOR PAINT COLOR. *TR
INTERIOR CHROME DOOR HANDLE CRACK, CAUSING THE CHROME PLATING TO SEPARATE. AFTER SEPARATION THE HANDLE BECOMES EXTREMELY SHARP AND CUT MY HAND.
TL*THE CONTACT OWNS A 2004 HYUNDAI SONATA. THE VEHICLE HAD WATER DAMAGED DUE TO A DEFECTIVE AIR CONDITIONING HOSE SEALANT THAT ALLOWED WATER TO PENETRATE WHICH CAUSED MILDEW TO FORM ON THE INTERIOR OF THE VEHICLE. THE DEALER STATED THAT THE INSTRUMENTAL PANEL WILL NEED TO BE REMOVED IN ORDER TO REPLACE THE DAMAGED WIRING AND SEA…
Read full complaint
TL*THE CONTACT OWNS A 2004 HYUNDAI SONATA. THE VEHICLE HAD WATER DAMAGED DUE TO A DEFECTIVE AIR CONDITIONING HOSE SEALANT THAT ALLOWED WATER TO PENETRATE WHICH CAUSED MILDEW TO FORM ON THE INTERIOR OF THE VEHICLE. THE DEALER STATED THAT THE INSTRUMENTAL PANEL WILL NEED TO BE REMOVED IN ORDER TO REPLACE THE DAMAGED WIRING AND SEALANT. THE CONTACT STATED THAT A YEAR AGO WATER PENETRATED THE INTERIOR OF THE VEHICLE DUE TO THE SEALANT AROUND THE BRAKE LIGHTS. THE VIN INFORMATION WASN'T AVAILABLE. THE MANUFACTURER WILL BE CONTACTED. THE FAILURE MILEAGE WAS 39,000 AND THE CURRENT MILEAGE WAS 69,000.
INTERIOR DOOR HANDLE CHROME PEELING OFF CAUSING SHARP METAL THAT CAN CUT FINGERS OR HANDS. *TR
INSIDE DOOR HANDLES THIN COVERING (APPEARS TO BE ALUMINUM) IS PEELING APART AND I HAVE CUT MY HAND ON THE SHARP EDGE WHICH CAME APART. DEALER WILL NOT REPLACE THE HANDLE BECAUSE HYUNDAI HAS NOT RECALLED THE 2004 MODELS WHICH HAS THE ***SAME PROBLEM**AS THE 2003 MODEL. *TR
CHROME IS PEELING OFF THE INTERIOR DOOR HANDLES CAUSING CUTS TO HANDS/FINGERS ON MY 2004 HYUNDAI SONATA. *TR
Official recalls
109V124000 · Suspension
Apr 16, 2009
HYUNDAI IS RECALLING 188,282 MY 2001-2004 SONATA AND MY 2001-2004 XG300 AND XG350 VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA. ROAD SALT APPLIED IN THESE JURISDICTIONS DURING THE WINTER MONTHS MAY RESULT IN PROGRESSIVE, INTERNAL CORROSION OF THE FRONT SUB-FRAME ON THE VEHICLES, AND MAY RESULT IN THINNING OR PERFORATION OF THE SUB-FRAME STEEL. THE CORROSION IS FREQUENTLY VISIBLE AND OFTEN DISCOVERED DURING INSPECTION OR ROUTINE MAINTENANCE, AND OWNERS MAY ALSO HEAR NOISES OR NOTICE TIRE MISALIGNMENT AND STEERING PULL. IF THESE SIGNALS ARE UNDETECTED OR UNHEEDED, THE CORROSION MAY PROGRESS AND THE FORWARD MOUNTING OF THE LOWER CONTROL ARM MAY DETACH FROM THE SUB-FRAME.
Consequence & remedy
Consequence: IF THAT HAPPENS, THE VEHICLE MAY LOSE DRIVE POWER TO THE WHEELS, AND THE FRONT WHEEL MAY MAKE CONTACT WITH THE FENDER OR WHEEL WELL, THEREBY INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL MEASURE THE THICKNESS OF THE FRONT SUB-FRAME AND INSPECT THE FRONT SUB-FRAME FOR CORROSION DAMAGE AND, IF NECESSARY, THE FRONT SUB-FRAME WILL BE REPLACED WITH A NEW SUB-FRAME THAT INCORPORATES ADDITIONAL HOLES IN THE UPPER AND LOWER PANELS. IF THE FRONT SUB-FRAME DOES NOT REQUIRE REPLACEMENT, THE DEALER WILL ADD DRAINAGE HOLES TO THE SUB-FRAME AND WILL TREAT THE SUB-FRAME WITH RUST-PROOFING MATERIAL TO STOP THE CORROSION PROCESS. THIS PROCEDURE WILL BE PERFORMED FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING APRIL 2009. OWNERS MAY CONTACT THE HYUNDAI CUSTOMER ASSISTANCE CENTER AT 1-800-633-5151.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA08016 · Front SUB-FRAME Corrosion
Opened Aug 21, 2008 · Closed Apr 20, 2009
Status: closed (inferred from source dates) · Structure; Structure:frame And Members; Suspension; Suspension:front; Suspension:front:control Arm
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Additional source detail variants (5)
Structure:frame And Members
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Structure
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Suspension:front:control Arm
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Suspension:front
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Suspension
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.