IllustrationPROBLEMS DUE TO RUST. STATEMENT FROM KEY HYUNDAI SERVICE ON 12/11/06 INDICATES EXCESSIVE RUST CAUSED REAR BRAKE PADS TO STICK AND WEAR DOWN PREMATURELY. I HAD TO PAY TO HAVE THEM REPLACED. *TR
2003 Hyundai Sonata
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2003 Hyundai Sonata do not stand out strongly from the model-year median of 161.
About this comparison →How this year compares
Owner complaints by model year
Compare all Sonata years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
310–25K
2525–50K
2850–75K
2175–100K
31100–150K
13150K+
149 reports with mileage · 50 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 43 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 38 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 19 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
17 crash reports2 fire reports28 injury reports
Structure complaints
38 reportsPROBLEMS DUE TO RUST. SERVICE AT COLUMBIA HYUNDAI ON 8/4/08 TO REPLACE POWER STEERING LINE AFTER POWER STEERING FAILED DUE TO LINE RUSTING OUT. *TR
TWO OF THE INSIDE DOOR HANDLES HAVE A SILVER METALLIC FOIL THAT HAS SPLIT AND COME LOOSE. MY SON CUT HIS FINGER OPENING THE DOOR. NOW THE DRIVER DOOR INSIDE HANDLE ALSO HAS THE SILVER FOIL COMING LOOSE. WE HAVE HAD TO PUT TAPE ON IT TO PREVENT GETTING ANOTHER CUT FINGER. *TR
I TOOK MY 2003 HYUNDAI SONATA IN FOR A ROUTINE INSPECTION AND FOUND OUT THAT THE ENGINE CRADLE HAD RUSTED THROUGH AND WAS NO LONGER DRIVABLE. THE ENGINE CRADLE HAD TO BE REPLACED, WHICH IS NO SMALL FEAT ON THIS VEHICLE. I HAVE READ SEVERAL OTHER COMPLAINTS OF THIS AND KNOW IT'S UNDER INVESTIGATION, BUT WANTED TO LOG MY COMPLAI…
Read full complaint
I TOOK MY 2003 HYUNDAI SONATA IN FOR A ROUTINE INSPECTION AND FOUND OUT THAT THE ENGINE CRADLE HAD RUSTED THROUGH AND WAS NO LONGER DRIVABLE. THE ENGINE CRADLE HAD TO BE REPLACED, WHICH IS NO SMALL FEAT ON THIS VEHICLE. I HAVE READ SEVERAL OTHER COMPLAINTS OF THIS AND KNOW IT'S UNDER INVESTIGATION, BUT WANTED TO LOG MY COMPLAINT AS WELL. *TR
WITHIN ONE YEAR OF BUYING MY HYUNDAI 2003 SONNTA, I CUT MY FINGER ON THE SILVER COATED INSIDE DOOR HANDLE ON THE DRIVER SIDE. THE SILVER COATING OF THE DOOR HANDLE SOMEHOW SPLINTERED AND CUT MY FINGER LIKE A STRAIGHT RAZOR BLADE. THE CUT WAS VERY DEEP AND MY FINGER BLED PROFUSELY FOR ABOUT 10 OR 15 MINUTES. I CONTACTED THE DE…
Read full complaint
WITHIN ONE YEAR OF BUYING MY HYUNDAI 2003 SONNTA, I CUT MY FINGER ON THE SILVER COATED INSIDE DOOR HANDLE ON THE DRIVER SIDE. THE SILVER COATING OF THE DOOR HANDLE SOMEHOW SPLINTERED AND CUT MY FINGER LIKE A STRAIGHT RAZOR BLADE. THE CUT WAS VERY DEEP AND MY FINGER BLED PROFUSELY FOR ABOUT 10 OR 15 MINUTES. I CONTACTED THE DEALER AND THE HANDLE WAS REPLACED. A SHORT TIME AFTER, MY HUSBAND SLICED HIS FINGER ON THE PASSENGER SIDE INSIDE DOOR HANDLE. AGAIN THE CUT WAS VERY DEEP; IT WAS LIKE A STRAIGHT RAZOR CUT. HIS FINGER BLED PROFUSELY FOR 10 - 15 MINUTES. AGAIN THE DEALER REPLACED THE HANDLE. BACK IN NOVEMBER OF 2007, SOMEONE WAS GETTING OUT OF THE BACK SEAT, AND THEN THIS PERSON CUT HER FINGER ON THE SILVER COATED INSIDE DOOR HANDLE. THIS TIME I CONTACTED HYUNDAI HEADQUARTERS AND TOLD THEM ABOUT THE PROBLEM..THE REP. I SPOKE TO SAID SHE DID NOT HEAR OF ANY SIMILIAR PROBLEMS. THEY CONTACTED THE CAR DEALER AND THE HANDLE WAS REPLACED. NOW A COUPLE OF WEEKS AGO, I CUT MY HAND ON THE PASSENGER DOOR HANDLE (THIS WAS A HANDLE THAT HAD PREVIOUSLY BEEN REPLACED). I CONTACTED HYUNDAI AGAIN AND AM AWAITING DISPOSITION ON THIS. THERE IS SOMETHING VERY WRONG WITH THESE DOOR HANDLES. THE CUT IT CAUSES IS LIKE A STRAIGHT RAZOR CUT. IT SLICES DEEP AND IT BLEEDS VERY BADLY. I TOLD HYUNDAI THAT I AM SURE I AM NOT THE ONLY PERSON TO EXPERIENCE THIS SERIOUS PROBLEM. IN FACT, I SEARCHED THE INTERNET AND FOUND THERE ARE OTHER PEOPLE THAT HAVE THE SAME PROBLEM WITH THESE DOOR HANDLES. THIS IS A VERY SERIOUS PROBLEM THAT I THINK THE GOV. NEEDS TO GET INVOLVED WITH. THANK YOU MARIA FACCHIN THANK YOU MARIA FACCHIN *TR
CUT FINGERS ON SHARP CHROME LAMINATION ON DOOR HANDLES. *TR
HAD PROBLEMS WITH THE BRAKES FOR OVER A YEAR NOW. HAD BOTH FRONT BRAKES REPLACED COSTING ABOUT $200. THEY STILL SQUEAK WHEN TURNING THE WHEEL , AND SOMETIMES WHEN DRIVING. ALSO, PANT HAS COMPLETELY COME OFF THE DOOR HANDLES, AND THERE WAS RUST ON DIFFERENT SPOTS OF THE CAR HOOD. I HAD THE DOOR HANDLES REPLACED INSIDE T…
Read full complaint
HAD PROBLEMS WITH THE BRAKES FOR OVER A YEAR NOW. HAD BOTH FRONT BRAKES REPLACED COSTING ABOUT $200. THEY STILL SQUEAK WHEN TURNING THE WHEEL , AND SOMETIMES WHEN DRIVING. ALSO, PANT HAS COMPLETELY COME OFF THE DOOR HANDLES, AND THERE WAS RUST ON DIFFERENT SPOTS OF THE CAR HOOD. I HAD THE DOOR HANDLES REPLACED INSIDE THE CAR BECAUSE THE SILVER WAS PEELING, CAUSING US TO CUT OUR HANDS, BUT THAT DIDN'T COST ME ANYTHING. *AK
DRIVER DOOR ALARM KEEPS ALARMING. I TOOK IT IN TO THE DEALER ONCE ALREADY TO BE REPAIRED. THE SERVICE MANAGER AT THIS TIME TOLD ME THAT ON THIS MODEL THE DOOR NEEDS TO BE TIGHTENED/ADJUSTED. NOW 2 MONTHS LATER THE SAME THING IS HAPPENING ONLY WORSE. NOW THE DOOR LIGHT IS COMING ON AND THE LIGHT ON THE DASH BOARD IS COMING ON.…
Read full complaint
DRIVER DOOR ALARM KEEPS ALARMING. I TOOK IT IN TO THE DEALER ONCE ALREADY TO BE REPAIRED. THE SERVICE MANAGER AT THIS TIME TOLD ME THAT ON THIS MODEL THE DOOR NEEDS TO BE TIGHTENED/ADJUSTED. NOW 2 MONTHS LATER THE SAME THING IS HAPPENING ONLY WORSE. NOW THE DOOR LIGHT IS COMING ON AND THE LIGHT ON THE DASH BOARD IS COMING ON. MAYBE THE DOOR IS DEFECTIVE AND GOING TO FALL OFF. *NM
Official recalls
609V317000 · Latches/locks/linkages:doors:latch
Aug 7, 2009
HYUNDAI IS RECALLING 82 MODEL YEAR 2002-2003 SONATA VEHICLES. REPEATED USE OF THE INTERIOR DOOR HANDLE MAY CAUSE WEAR OF THE CHROME PLATING. IF THE TOP EDGE OF THE HANDLE HAS VERY THIN CHROME PLATING THAT PORTION OF THE PLATING MAY WEAR AWAY MORE EASILY THAN MORE THICKLY PLATED AREAS AS THE DOOR HANDLE IS USED. THE WORN CHROME PLATING ON THE UPPER EDGE OF THE HANDLE MAY RESULT IN A CRACK OR SEPARATION BETWEEN THE CHROME PLATING ON THE INBOARD AND OUTBOARD SURFACES OF THE HANDLE, WHICH MAY FORM A SHARP EDGE.
Consequence & remedy
Consequence: A SHARP EDGE COULD LACERATE OR OTHERWISE INJURE A VEHICLE OCCUPANT.
Remedy: DEALERS WILL REPAIR THE CHROME PLATED INTERIOR DOOR HANDLE FREE OF CHARGE. THE RECALL BEGAN ON SEPTEMBER 16, 2009. OWNERS MAY CONTACT HYUNDAI OF PUERTO RICO AT 1-787-999-3333.
09V171000 · Latches/locks/linkages:doors:latch
May 21, 2009
HYUNDAI IS RECALLING 91,350 MY 2002-2003 HYUNDAI SONATA VEHICLES. REPEATED USE OF THE INTERIOR DOOR HANDLE MAY CAUSE WEAR OF THE CHROME PLATE. IF THE TOP EDGE OF THE HANDLE HAS VERY THIN CHROME PLATING, THAT PORTION OF THE PLATING MAY WEAR AWAY MORE EASILY THAN MORE THICKLY PLATED AREAS AS THE DOOR HANDLE IS USED. THE WORN CHROME PLATING ON THE UPPER EDGE OF THE HANDLE MAY RESULT IN A CRACK OR SEPARATION BETWEEN THE CHROME PLATING ON THE INBOARD AND OUTBOARD SURFACES OF THE HANDLE, WHICH MAY FORM A SHARP EDGE.
Consequence & remedy
Consequence: THIS MAY INFLICT LACERATION INJURIES TO ANYONE USING THE DOOR HANDLE.
Remedy: DEALERS WILL REPAIR THE CHROME PLATED INTERIOR DOOR HANDLE FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING JUNE 2009. OWNERS MAY CONTACT HYUNDAI CUSTOMER ASSISTANCE CENTER AT 1-800-633-5151.
09V124000 · Suspension
Apr 16, 2009
HYUNDAI IS RECALLING 188,282 MY 2001-2004 SONATA AND MY 2001-2004 XG300 AND XG350 VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA. ROAD SALT APPLIED IN THESE JURISDICTIONS DURING THE WINTER MONTHS MAY RESULT IN PROGRESSIVE, INTERNAL CORROSION OF THE FRONT SUB-FRAME ON THE VEHICLES, AND MAY RESULT IN THINNING OR PERFORATION OF THE SUB-FRAME STEEL. THE CORROSION IS FREQUENTLY VISIBLE AND OFTEN DISCOVERED DURING INSPECTION OR ROUTINE MAINTENANCE, AND OWNERS MAY ALSO HEAR NOISES OR NOTICE TIRE MISALIGNMENT AND STEERING PULL. IF THESE SIGNALS ARE UNDETECTED OR UNHEEDED, THE CORROSION MAY PROGRESS AND THE FORWARD MOUNTING OF THE LOWER CONTROL ARM MAY DETACH FROM THE SUB-FRAME.
Consequence & remedy
Consequence: IF THAT HAPPENS, THE VEHICLE MAY LOSE DRIVE POWER TO THE WHEELS, AND THE FRONT WHEEL MAY MAKE CONTACT WITH THE FENDER OR WHEEL WELL, THEREBY INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL MEASURE THE THICKNESS OF THE FRONT SUB-FRAME AND INSPECT THE FRONT SUB-FRAME FOR CORROSION DAMAGE AND, IF NECESSARY, THE FRONT SUB-FRAME WILL BE REPLACED WITH A NEW SUB-FRAME THAT INCORPORATES ADDITIONAL HOLES IN THE UPPER AND LOWER PANELS. IF THE FRONT SUB-FRAME DOES NOT REQUIRE REPLACEMENT, THE DEALER WILL ADD DRAINAGE HOLES TO THE SUB-FRAME AND WILL TREAT THE SUB-FRAME WITH RUST-PROOFING MATERIAL TO STOP THE CORROSION PROCESS. THIS PROCEDURE WILL BE PERFORMED FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING APRIL 2009. OWNERS MAY CONTACT THE HYUNDAI CUSTOMER ASSISTANCE CENTER AT 1-800-633-5151.
04V369000 · Fuel System, Gasoline:storage
Jul 26, 2004
CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, "FUEL SYSTEM INTEGRITY" A VALVE ON THE FUEL TANK ASSEMBLY MAY NOT CLOSE PROPERLY. IF A VEHICLE ROLLS OVER AND THE FUEL TANK ASSEMBLY VALVE IS NOT PROPERLY CLOSED, FUEL SPILLAGE MAY OCCUR.
Consequence & remedy
Consequence: FUEL SPILLAGE IN THE PRESENCE OF AN IGNITION SOURCE MAY RESULT IN A FIRE.
Remedy: DEALERS WILL INSTALL AN ADDITIONAL FUEL TANK ASSEMBLY VALVE. THE RECALL BEGAN ON OCTOBER 5, 2004. OWNERS SHOULD CONTACT HYUNDAI DE PUERTO RICO AT 1-800-981-0188.
04V178000 · Fuel System, Gasoline:storage:tank Assembly
Apr 9, 2004
SOME PASSENGER VEHICLES CONTAIN A FUEL TANK ASSEMBLY VALVE THAT MAY NOT CLOSE PROPERLY. IF A VEHICLE WITH A FUEL TANK ASSEMBLY VALVE THAT IS NOT PROPERLY CLOSED WERE TO ROLL OVER, FUEL SPILLAGE MAY OCCUR.
Consequence & remedy
Consequence: FUEL SPILLAGE IN THE PRESENCE OF AN IGNITION SOURCE MAY RESULT IN A FIRE.
Remedy: DEALERS WILL INSTALL AN ADDITIONAL FUEL TANK ASSEMBLY VALVE. OWNER NOTIFICATION BEGAN ON JUNE 30, 2004. OWNERS SHOULD CONTACT HYUNDAI AT 1-800-633-5151.
03V097000 · Tires:temporary/emergency Spare Tire
Mar 17, 2003
ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A TRACTION CONTROL SYSTEM (TCS), IF THE T125/70D-15 COMPACT SPARE TIRE IS INSTALLED ON A FRONT WHEEL POSITION, THE TCS MAY INADVERTENTLY ACTIVATE BEGINNING AT SPEEDS OF 20 MPH.
Consequence & remedy
Consequence: INADVERTENT ACTIVATION OF THE TCS WILL CAUSE AUTOMATIC APPLICATION OF THE BRAKE AT THE WHEEL WHERE THE COMPACT SPARE TIRE IS INSTALLED. INADVERTENT BRAKE APPLICATION COULD CAUSE OVERHEATING AND DAMAGE TO THE BRAKE, AND MAY PREVENT THE VEHICLE FROM BEING DRIVEN AT SPEEDS ABOVE 20 MPH, WHICH COULD RESULT IN A CRASH.
Remedy: DEALERS WILL REPLACE THE SPARE TIRE WITH A NEW LARGER DIAMETER T125/80R-15 COMPACT SPARE TIRE AND A NEW TIRE PRESSURE LABEL WILL BE INSTALLED ON THE DRIVER'S DOOR TO PROVIDE INFORMATION APPLICABLE TO THE T125/80R-15 COMPACT SPARE TIRE. VEHICLES PRODUCED FROM NOVEMBER 15, 2002 THROUGH DECEMBER 16 2002, ALREADY CONTAIN T125/80R-15 COMPACT SPARE TIRES, WILL ONLY REQUIRE NEW TIRE PRESSURE LABELS. OWNER NOTIFICATION BEGAN JUNE 30, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT HYUNDAI AT 1-800-633-5151.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3PE08071 · Interior Door Handle Laceration Hazard
Opened Dec 15, 2008 · Closed May 29, 2009
Status: closed (inferred from source dates) · Latches/locks/linkages:doors:latch
THE MANUFACTURER HAS ISSUED A SAFETY RECALL NOTIFICATION AS A RESULT OF THIS INVESTIGATION.THE RECALL AFFECTS 91,202 MY 2002-2003 SUBJECT VEHICLES PRODUCED FROM JANUARY 28, 2002, THROUGH MARCH 22, 2003.THE VEHICLE RECALL POPULATION WAS DEFINED BY THE MANUFACTURER'S USE OF A NEW SUPPLIER FOR THE CHROME PLATING PROCESS BEGINNING IN JANUARY 2002, AND A PRODUCTION CHANGE IN MARCH 2003 TO IMPROVE ADHESION OF THE PLATING TO THE DOOR HANDLE.VEHICLES BEING RECALLED REPRESENT 59 PERCENT OF THE TOTAL MY 2002-2003 PRODUCTION, BUT ACCOUNT FOR 91 PERCENT OF THE CONSUMER COMPLAINTS RECEIVED.THE PROCESS CHANGE FOR MY 2002 VEHICLES RESULTED IN A DRAMATIC INCREASE IN COMPLAINTS (1200 PERCENT ON A PER UNIT RATE BASIS).MY 2003 VEHICLES BUILT AFTER MARCH 2003 PRODUCTION CHANGE SHOWED A SIMILAR DECLINE IN THE COMPLAINT RATE.BASED ON THE MANUFACTURER'S ACTION, THIS INVESTIGATION HAS BEEN CLOSED.
EA08016 · Front SUB-FRAME Corrosion
Opened Aug 21, 2008 · Closed Apr 20, 2009
Status: closed (inferred from source dates) · Structure; Structure:frame And Members; Suspension; Suspension:front; Suspension:front:control Arm
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Additional source detail variants (5)
Structure:frame And Members
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Structure
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Suspension:front:control Arm
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Suspension:front
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
Suspension
IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.
PE05059 · Tire Valve Stem Failures
Opened Nov 7, 2005 · Closed May 11, 2006
Status: closed (inferred from source dates) · Tires; Tires:valve; Wheels:hub
THE OFFICE OF DEFECTS INVESTIGATION (ODI) OPENED A PRELIMINARY EVALUATION (PE), PE05-059, BASED ON NINE CONSUMER COMPLAINTS OF TIRE VALVE STEM FAILURES.THE ALLEGED VALVE STEM FAILURES OCCURRED ONLY AFTER TIRE REPLACEMENT FROM THE ORIGINAL EQUIPMENT (OE) TIRE (MICHELIN 205/65R15 ENERGY MXV4 PLUS) TO A NON-OE? AFTERMARKET TIRE.NINETY-EIGHT PERCENT OF THE AFTERMARKET TIRES ALLEGED TO BE ASSOCIATED WITH THE TIRE VALVE STEM FAILURES WERE DETERMINED TO BE AFTERMARKET TIRES PRODUCED BY BRANDS OF MICHELIN GROUP (BF GOODRICH AND UNIROYAL).MICHELIN ISSUED A TECHNICAL BULLETIN ON SEPTEMBER 15, 2005 MAKING RETAILERS AWARE OF A POTENTIAL WHEEL COVER INCOMPATIBILITY WITH BF GOODRICH TRACTION T/AAND TOURING T/A PRO SERIES TIRES THAT COULD CAUSE WHEEL COVER MOVEMENT AND IN EXTREME CASES TIRE VALVE DAMAGE. MICHELIN HAS, ADDITIONALLY, REDESIGNED THE BF GOODRICH AND UNIROYAL TIRES ALLEGEDLY ASSOCIATED WITH THE VALVE STEM FAILURES, AS OF THE FIRST QUARTER OF CALENDAR YEAR 2006. THE PREVIOUS DESIGN VERSION OF BOTH TIRES IS NO LONGER AVAILABLE.NO COMPLAINTS HAVE BEEN SUBMITTED TO ODI FOR TIRES MANUFACTURED AFTER THE INTRODUCTION OF THE REDESIGNED TIRES.THERE HAVE BEEN NO ACCIDENTS, INJURIES OR LOSS OF VEHICLE CONTROL ATTRIBUTED TO THE ALLEGED DEFECT.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL CONTINUE TO MONITOR COMPLAINTS AND OTHER INFORMATION RELATING TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES AND TAKE FURTHER ACTION IN THE FUTURE IF WARRANTED.
Additional source detail variants (3)
Tires
THE OFFICE OF DEFECTS INVESTIGATION (ODI) OPENED A PRELIMINARY EVALUATION (PE), PE05-059, BASED ON NINE CONSUMER COMPLAINTS OF TIRE VALVE STEM FAILURES.THE ALLEGED VALVE STEM FAILURES OCCURRED ONLY AFTER TIRE REPLACEMENT FROM THE ORIGINAL EQUIPMENT (OE) TIRE (MICHELIN 205/65R15 ENERGY MXV4 PLUS) TO A NON-OE? AFTERMARKET TIRE.NINETY-EIGHT PERCENT OF THE AFTERMARKET TIRES ALLEGED TO BE ASSOCIATED WITH THE TIRE VALVE STEM FAILURES WERE DETERMINED TO BE AFTERMARKET TIRES PRODUCED BY BRANDS OF MICHELIN GROUP (BF GOODRICH AND UNIROYAL).MICHELIN ISSUED A TECHNICAL BULLETIN ON SEPTEMBER 15, 2005 MAKING RETAILERS AWARE OF A POTENTIAL WHEEL COVER INCOMPATIBILITY WITH BF GOODRICH TRACTION T/AAND TOURING T/A PRO SERIES TIRES THAT COULD CAUSE WHEEL COVER MOVEMENT AND IN EXTREME CASES TIRE VALVE DAMAGE. MICHELIN HAS, ADDITIONALLY, REDESIGNED THE BF GOODRICH AND UNIROYAL TIRES ALLEGEDLY ASSOCIATED WITH THE VALVE STEM FAILURES, AS OF THE FIRST QUARTER OF CALENDAR YEAR 2006. THE PREVIOUS DESIGN VERSION OF BOTH TIRES IS NO LONGER AVAILABLE.NO COMPLAINTS HAVE BEEN SUBMITTED TO ODI FOR TIRES MANUFACTURED AFTER THE INTRODUCTION OF THE REDESIGNED TIRES.THERE HAVE BEEN NO ACCIDENTS, INJURIES OR LOSS OF VEHICLE CONTROL ATTRIBUTED TO THE ALLEGED DEFECT.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL CONTINUE TO MONITOR COMPLAINTS AND OTHER INFORMATION RELATING TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES AND TAKE FURTHER ACTION IN THE FUTURE IF WARRANTED.
Tires:valve
THE OFFICE OF DEFECTS INVESTIGATION (ODI) OPENED A PRELIMINARY EVALUATION (PE), PE05-059, BASED ON NINE CONSUMER COMPLAINTS OF TIRE VALVE STEM FAILURES.THE ALLEGED VALVE STEM FAILURES OCCURRED ONLY AFTER TIRE REPLACEMENT FROM THE ORIGINAL EQUIPMENT (OE) TIRE (MICHELIN 205/65R15 ENERGY MXV4 PLUS) TO A NON-OE? AFTERMARKET TIRE.NINETY-EIGHT PERCENT OF THE AFTERMARKET TIRES ALLEGED TO BE ASSOCIATED WITH THE TIRE VALVE STEM FAILURES WERE DETERMINED TO BE AFTERMARKET TIRES PRODUCED BY BRANDS OF MICHELIN GROUP (BF GOODRICH AND UNIROYAL).MICHELIN ISSUED A TECHNICAL BULLETIN ON SEPTEMBER 15, 2005 MAKING RETAILERS AWARE OF A POTENTIAL WHEEL COVER INCOMPATIBILITY WITH BF GOODRICH TRACTION T/AAND TOURING T/A PRO SERIES TIRES THAT COULD CAUSE WHEEL COVER MOVEMENT AND IN EXTREME CASES TIRE VALVE DAMAGE. MICHELIN HAS, ADDITIONALLY, REDESIGNED THE BF GOODRICH AND UNIROYAL TIRES ALLEGEDLY ASSOCIATED WITH THE VALVE STEM FAILURES, AS OF THE FIRST QUARTER OF CALENDAR YEAR 2006. THE PREVIOUS DESIGN VERSION OF BOTH TIRES IS NO LONGER AVAILABLE.NO COMPLAINTS HAVE BEEN SUBMITTED TO ODI FOR TIRES MANUFACTURED AFTER THE INTRODUCTION OF THE REDESIGNED TIRES.THERE HAVE BEEN NO ACCIDENTS, INJURIES OR LOSS OF VEHICLE CONTROL ATTRIBUTED TO THE ALLEGED DEFECT.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL CONTINUE TO MONITOR COMPLAINTS AND OTHER INFORMATION RELATING TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES AND TAKE FURTHER ACTION IN THE FUTURE IF WARRANTED.
Wheels:hub
THE OFFICE OF DEFECTS INVESTIGATION (ODI) OPENED A PRELIMINARY EVALUATION (PE), PE05-059, BASED ON NINE CONSUMER COMPLAINTS OF TIRE VALVE STEM FAILURES.THE ALLEGED VALVE STEM FAILURES OCCURRED ONLY AFTER TIRE REPLACEMENT FROM THE ORIGINAL EQUIPMENT (OE) TIRE (MICHELIN 205/65R15 ENERGY MXV4 PLUS) TO A NON-OE? AFTERMARKET TIRE.NINETY-EIGHT PERCENT OF THE AFTERMARKET TIRES ALLEGED TO BE ASSOCIATED WITH THE TIRE VALVE STEM FAILURES WERE DETERMINED TO BE AFTERMARKET TIRES PRODUCED BY BRANDS OF MICHELIN GROUP (BF GOODRICH AND UNIROYAL).MICHELIN ISSUED A TECHNICAL BULLETIN ON SEPTEMBER 15, 2005 MAKING RETAILERS AWARE OF A POTENTIAL WHEEL COVER INCOMPATIBILITY WITH BF GOODRICH TRACTION T/AAND TOURING T/A PRO SERIES TIRES THAT COULD CAUSE WHEEL COVER MOVEMENT AND IN EXTREME CASES TIRE VALVE DAMAGE. MICHELIN HAS, ADDITIONALLY, REDESIGNED THE BF GOODRICH AND UNIROYAL TIRES ALLEGEDLY ASSOCIATED WITH THE VALVE STEM FAILURES, AS OF THE FIRST QUARTER OF CALENDAR YEAR 2006. THE PREVIOUS DESIGN VERSION OF BOTH TIRES IS NO LONGER AVAILABLE.NO COMPLAINTS HAVE BEEN SUBMITTED TO ODI FOR TIRES MANUFACTURED AFTER THE INTRODUCTION OF THE REDESIGNED TIRES.THERE HAVE BEEN NO ACCIDENTS, INJURIES OR LOSS OF VEHICLE CONTROL ATTRIBUTED TO THE ALLEGED DEFECT.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL CONTINUE TO MONITOR COMPLAINTS AND OTHER INFORMATION RELATING TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES AND TAKE FURTHER ACTION IN THE FUTURE IF WARRANTED.