IllustrationWHEN THE HEADLIGHTS ARE IN THE "ON" POSITION THEY TURN OFF WHEN THE TURN SIGNAL IS USED. THIS HAPPENS CONSISTENTLY AND IS REPRODUCIBLE.
2012 Hyundai Genesis
Owner reports · Recalls · Investigations
More warning signs than most Genesis years
Owner complaints for the 2012 Hyundai Genesis are substantially higher than the model-year median of 109.
About this comparison →How this year compares
Owner complaints by model year
Compare all Genesis years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
340–25K
5925–50K
5350–75K
4375–100K
13100–150K
8150K+
210 reports with mileage · 49 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine. Review the 68 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 49 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 39 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
8 crash reports1 fire reports5 injury reports
What owners actually said
259 reportsTROUBLE WITH PUSHING DOWN HARD ON THE BRAKE PEDAL AND CONCERNED WITH BRAKE EFFECTIVENESS. AND SAFETY. FORCED TO PUSH BRAKE ALL THE WAY TO THE FLOOR IN ORDER TO STOP.
TL* THE CONTACT OWNS A 2012 HYUNDAI GENESIS. WHILE DRIVING VARIOUS SPEEDS, THE VEHICLE SUDDENLY SHUT COMPLETELY OFF. THE VEHICLE WAS TAKEN TO THE DEALER, BUT THE CAUSE OF THE FAILURE COULD NOT BE DIAGNOSED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE VIN WAS NOT VALID. THE FAILURE MILEAGE WAS 52,000.
TL* THE CONTACT OWNS A 2012 HYUNDAI GENESIS. WHILE DRIVING AT ANY SPEED, THE PARKING SENSOR INDICATOR ILLUMINATED. THE VEHICLE WAS TAKEN TO A DEALER WHERE IT WAS DIAGNOSED THAT THE PARKING SENSOR WAS FRACTURED AND NEEDED TO BE REPLACED. THE TECHNICIAN STATED THAT THE WARRANTY EXPIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILU…
Read full complaint
TL* THE CONTACT OWNS A 2012 HYUNDAI GENESIS. WHILE DRIVING AT ANY SPEED, THE PARKING SENSOR INDICATOR ILLUMINATED. THE VEHICLE WAS TAKEN TO A DEALER WHERE IT WAS DIAGNOSED THAT THE PARKING SENSOR WAS FRACTURED AND NEEDED TO BE REPLACED. THE TECHNICIAN STATED THAT THE WARRANTY EXPIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND STATED THAT THE CONTACT WAS RESPONSIBLE FOR THE REPAIRS. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS 5,025.
BOUGHT NEW IN JULY 2012. CAR HAS AROUND 46K ON IT. I HAVE HAD TO REPLACE 2 OF THE 4 MICHELIN ENERGY SAVER A/S TIRES BECAUSE OF CRACKING IN THE SIDEWALLS. BOTH HAD CHUNKS MISSING AND THE CRACKING/ROT WAS SPREADING. I DROVE ON THEM FOR MONTHS LIKE THAT, LUCKILY WITHOUT INCIDENT. I BOUGHT A PAIR USED TO REPLACE THEM SO I COULD…
Read full complaint
BOUGHT NEW IN JULY 2012. CAR HAS AROUND 46K ON IT. I HAVE HAD TO REPLACE 2 OF THE 4 MICHELIN ENERGY SAVER A/S TIRES BECAUSE OF CRACKING IN THE SIDEWALLS. BOTH HAD CHUNKS MISSING AND THE CRACKING/ROT WAS SPREADING. I DROVE ON THEM FOR MONTHS LIKE THAT, LUCKILY WITHOUT INCIDENT. I BOUGHT A PAIR USED TO REPLACE THEM SO I COULD GET FULL WEAR OUT OF THE REMAINING TOO, BUT I AM WARY OF BUYING MICHELINS FOR MY NEXT SET.
INTERMITTENT BRAKE FAILURES. SEEMS THERE HAS BEEN A RECALL FOR BAD BRAKE FLUID ON THIS MODEL YEAR HYUNDAI GENESIS SEDAN. HYUNDAI WOULD NOT COVER THIS VEHICLE UNDER THE RECALL WHEN CONTACTED. THE VEHICLE HAS AN INTERMITTENT SOFT BRAKE PEDAL WHICH GOES ALL THE WAY TO THE FLOOR UNDER HARD AND SOFT BRAKING CONDITIONS, WHETHER MOV…
Read full complaint
INTERMITTENT BRAKE FAILURES. SEEMS THERE HAS BEEN A RECALL FOR BAD BRAKE FLUID ON THIS MODEL YEAR HYUNDAI GENESIS SEDAN. HYUNDAI WOULD NOT COVER THIS VEHICLE UNDER THE RECALL WHEN CONTACTED. THE VEHICLE HAS AN INTERMITTENT SOFT BRAKE PEDAL WHICH GOES ALL THE WAY TO THE FLOOR UNDER HARD AND SOFT BRAKING CONDITIONS, WHETHER MOVING FAST OR SLOW AND IN ALL WEATHER CONDITIONS. THE BRAKE PADS AND ALL 4 ROTORS ARE IN GOOD REPAIR. THERE IS NO AIR IN THE BRAKE LINES. IT APPEARS TO BE THE ABS MODULE THAT IS FAILING AND CAUSING UNSAFE BRAKING CONDITIONS WITHOUT WARNING. THERE ARE NUMEROUS ONLINE FORUM COMPLAINTS ABOUT THIS MODULE WHICH SEEMS TO BE A FAULT IN DESIGN BY HYUNDAI. MY HOPE IS THAT NHTSA CAN INFORM OTHER OWNERS OF THIS MODEL YEAR THAT UNSAFE BRAKING CONDITIONS CAN HAPPEN AT ANY TIME FROM FAILURE OF THIS ABS MODULE. *TR
THE BRAKE PEDAL GOES COMPLETELY TO THE FLOOR. BRAKES ACT AS IF FAILING. DEALER DIAGNOSED BRAKE MASTER CYLINDER DEFECT, REQUIRING REPLACEMENT OF THE MASTER CYLINDER. MILEAGE ONLY 67,000 MILES.
TL* THE CONTACT OWNS A 2012 HYUNDAI GENESIS. WHILE DRIVING 20 MPH, THE VEHICLE STALLED AND THE CHECK ENGINE WARNING INDICATOR ILLUMINATED. THE VEHICLE WAS ABLE TO RESTART ON THE FIRST ATTEMPT, BUT THE FAILURE RECURRED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILE…
Read full complaint
TL* THE CONTACT OWNS A 2012 HYUNDAI GENESIS. WHILE DRIVING 20 MPH, THE VEHICLE STALLED AND THE CHECK ENGINE WARNING INDICATOR ILLUMINATED. THE VEHICLE WAS ABLE TO RESTART ON THE FIRST ATTEMPT, BUT THE FAILURE RECURRED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 93,000.
SPORADICALLY THE BRAKE PEDAL GOES ALL THE WAY TO FLOOR. PEDAL HAS TO BE PUMPED 2-3 TIMES BEFORE BRAKES ENGAGE. THIS HAS HAPPENED ON 3 DRIVING OCCASIONS OVER 10 DAYS. TOOK IT TO DEALER THIS MORNING WHO SAID UNLESS HE COULD REPLICATE ISSUE, HE WILL NOT REPAIR DESPITE PRIOR RECALL FOR SAME ISSUE. YESTERDAY ON PHONE, HE SAID HE …
Read full complaint
SPORADICALLY THE BRAKE PEDAL GOES ALL THE WAY TO FLOOR. PEDAL HAS TO BE PUMPED 2-3 TIMES BEFORE BRAKES ENGAGE. THIS HAS HAPPENED ON 3 DRIVING OCCASIONS OVER 10 DAYS. TOOK IT TO DEALER THIS MORNING WHO SAID UNLESS HE COULD REPLICATE ISSUE, HE WILL NOT REPAIR DESPITE PRIOR RECALL FOR SAME ISSUE. YESTERDAY ON PHONE, HE SAID HE WOULD INSPECT AND FILE CLAIM WITH HYUNDAI. APPARENTLY BRAKE FLUID WAS REPLACED IN 2013 DUE TO RECALL BY PRIOR OWNER. NOW SAME THING IS HAPPENING. PROBLEM OCCURS UNTIL ENGINE IS TURNED OFF. 3 TIMES IN 10 DAYS IS FRIGHTENING. FORTUNATELY, I WAS FAR ENOUGH BEHIND CAR IN FRONT TO HAVE TIME TO PUMP BRAKES. *TR
HEADLIGHTS BLINK ON/OFF WHEN USING TURN SIGNAL. DOING RESEARCH, I SEE THAT MANY PEOPLE HAVE COMPLAINED ABOUT THIS AND THE FIX IS TO REPLACE THE TURN SIGNAL STALK ($400).
Official recalls
216V117000 · Visibility:windshield Wiper/washer:motor
Feb 29, 2016
Hyundai Motor America (Hyundai) is recalling certain model year 2012 Genesis vehicles manufactured August 1, 2011, to April 30, 2012, and 2011-2013 Equus vehicles manufactured July 10, 2011, to June 12, 2012. The windshield wiper motor cover seal on the affected vehicles may degrade allowing corrosion on the wiper motor's circuit board. The corrosion can cause intermittent or total loss of wiper function.
Consequence & remedy
Consequence: Inoperative wipers during inclement weather can decrease driver visibility, increasing the risk of a crash.
Remedy: Hyundai will notify owners, and dealers will replace the wiper motor cover and seal, free of charge. The recall began on April 22, 2016. Owners may contact Hyundai customer service at 1-800-633-5151. Hyundai's number for this recall is 140.
13V489000 · Service Brakes, Hydraulic:fluid
Oct 29, 2013
Hyundai is recalling certain model year 2009-2012 Genesis vehicles manufactured April 30, 2008, through March 28, 2012. The vehicles may contain brake fluid which does not protect against corrosion of the Hydraulic Electronic Control Unit (HECU).
Consequence & remedy
Consequence: If the module corrodes, reduced brake effectiveness may result, increasing the risk of a crash.
Remedy: Hyundai will notify owners and instruct them to bring their vehicle to a dealer for service. Hyundai will inspect the HECU module for proper operation, and will replace the modules as necessary. Hyundai will replace the factory brake fluid in those vehicles that have not previously had the factory brake fluid replaced. These repairs will be done free of charge. The recall began on December 24, 2013. Owners may contact Hyundai at 1-800-633-5151 or by email at consumeraffairs@hmausa.com. Hyundai's recall number is 114.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE13033 · Brake Hydraulic Control Module Failure
Opened Oct 17, 2013 · Closed Apr 4, 2014
Status: closed (inferred from source dates) · Service Brakes, Hydraulic; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Additional source detail variants (3)
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Service Brakes, Hydraulic
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354