IllustrationMY TAIL LIGHTS AND BRAKE LIGHTS STOPPED WORKING. REPLACED TAIL LIGHT SWITCH.DIDN'T SOLVE THE PROBLEM.
2011 Hyundai Genesis
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2011 Hyundai Genesis do not stand out strongly from the model-year median of 109.
About this comparison →How this year compares
Owner complaints by model year
Compare all Genesis years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
150–25K
1825–50K
2750–75K
2475–100K
13100–150K
2150K+
99 reports with mileage · 23 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 19 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Vehicle Speed Control. Review the 16 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 15 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
12 crash reports3 fire reports6 injury reports
Exterior Lighting complaints
11 reportsHEADLIGHTS WILL GO OUT WHEN ENGAGING THE TURN SIGNAL WHEN ON THE ON POSITION ONLY ( NOT THE AUTO POSITION) LIGHT WILL REMAIN OFF FOR BETWEEN 1 AND 10 SECONDS. THIS CAN HAPPEN WHEN MOVING OR STOPPED. THERE IS A DEAD SPOT IN THE SWITCH AND JUST TOUCHING IT CAN CAUSE THE HEADLIGHTS TO GO OUT.
TL* THE CONTACT OWNS A 2011 HYUNDAI GENESIS. WHILE DEPRESSING THE BRAKE PEDAL, THE BRAKE LIGHTS FAILED TO ILLUMINATE. THE CAUSE OF THE FAILURE WAS NOT DIAGNOSED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED. THE VIN WAS NOT AVAILABLE. THE FAILURE MILEAGE WAS 33,000.
WHEN USING THE TURN INDICATOR, THE HEADLIGHTS WILL FLASH OFF. SOMETIMES IT IS JUST FOR A MOMENT AND OTHER TIMES FOR A SECOND OR TWO. THIS LEAVES ME IN COMPLETE DARKNESS AND OPPOSING DRIVERS GETTING UPSET THAT MY LIGHTS ARE FLASHING ON AND OFF. THIS OCCURS WHETHER I AM IN MOTION, STOPPED TO MAKE A TURN, OR AT ANY TIME WHEN THE TU…
Read full complaint
WHEN USING THE TURN INDICATOR, THE HEADLIGHTS WILL FLASH OFF. SOMETIMES IT IS JUST FOR A MOMENT AND OTHER TIMES FOR A SECOND OR TWO. THIS LEAVES ME IN COMPLETE DARKNESS AND OPPOSING DRIVERS GETTING UPSET THAT MY LIGHTS ARE FLASHING ON AND OFF. THIS OCCURS WHETHER I AM IN MOTION, STOPPED TO MAKE A TURN, OR AT ANY TIME WHEN THE TURN SIGNAL IS USED AND THE HEADLIGHTS ARE ON. THIS ALSO HAPPENS WHEN JUST "TAPPING" THE 3-BLINK LANE CHANGE OPTION FOR THE TURN SIGNALS.
WHEN ENGAGING THE TURN SIGNAL, THE HEADLIGHTS WILL FLASH OFF AND BACK ON QUICKLY. THIS ONLY HAPPENS WHEN THE HEADLIGHTS ARE SET TO "ON" (AS OPPOSED TO "AUTO"). IT DOES NOT HAPPEN EVERY TIME THE TURN SIGNAL IS ENGAGED, BUT IT HAPPENS 15-20% OF THE TIME. IT IS DISTRACTING TO THE DRIVER OF THE VEHICLE AS WELL AS OTHER DRIVERS AR…
Read full complaint
WHEN ENGAGING THE TURN SIGNAL, THE HEADLIGHTS WILL FLASH OFF AND BACK ON QUICKLY. THIS ONLY HAPPENS WHEN THE HEADLIGHTS ARE SET TO "ON" (AS OPPOSED TO "AUTO"). IT DOES NOT HAPPEN EVERY TIME THE TURN SIGNAL IS ENGAGED, BUT IT HAPPENS 15-20% OF THE TIME. IT IS DISTRACTING TO THE DRIVER OF THE VEHICLE AS WELL AS OTHER DRIVERS AROUND THE VEHICLE. I'VE RESEARCHED THIS AND FOUND IT IS NOT AN ISOLATED CASE: HTTP://GENESISOWNERS.COM/HYUNDAI-GENESIS-FORUM/SHOWTHREAD.PHP?S=15515FE08925ADEB2371411165FE2C76&T=12026&PAGE=2. *TR
TL*THE CONTACT OWNS A 2011 HYUNDAI GENESIS. THE CONTACT STATED THAT THE BRAKE LIGHTS FAILED. THE VEHICLE WAS NOT TAKEN TO THE DEALER TO BE DIAGNOSED. THE MANUFACTURER STATED THAT THE VEHICLE WAS NOT INCLUDED IN NHTSA RECALL CAMPAIGN NUMBER: 13V113000 (EXTERIOR LIGHTING). THE FAILURE MILEAGE WAS 52,000.
TL* THE CONTACT OWNS A 2011 HYUNDAI GENESIS. THE CONTACT RECEIVED A NOTIFICATION FOR NHTSA CAMPAIGN NUMBER: 14V713000 (EXTERIOR LIGHTING) AND STATED THAT THE PART NEEDED WAS UNAVAILABLE TO REPAIR THE VEHICLE. THE DEALER WAS UNABLE TO INFORM WHEN THE PART WOULD BECOME AVAILABLE. THE MANUFACTURER WAS NOTIFIED OF THE ISSUE. THE CON…
Read full complaint
TL* THE CONTACT OWNS A 2011 HYUNDAI GENESIS. THE CONTACT RECEIVED A NOTIFICATION FOR NHTSA CAMPAIGN NUMBER: 14V713000 (EXTERIOR LIGHTING) AND STATED THAT THE PART NEEDED WAS UNAVAILABLE TO REPAIR THE VEHICLE. THE DEALER WAS UNABLE TO INFORM WHEN THE PART WOULD BECOME AVAILABLE. THE MANUFACTURER WAS NOTIFIED OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE.
I WAS PULLED OVER BY A POLICEMAN WHO NOTICED THAT ALL OF MY REAR BRAKE LIGHTS WERE NOT WORKING. THERE WAS NO WARNING LIGHT ON MY DASH TO NOTIFY ME OF THIS PROBLEM. I TOOK MY CAR TO THE SERVICE DEPARTMENT OF A HYUNDAI DEALERSHIP AND THEY SAID A DIODE HAD FAILED. I WAS PULLED OVER BY A POLICEMAN ABOUT 2 YEARS AGO FOR THE SAME I…
Read full complaint
I WAS PULLED OVER BY A POLICEMAN WHO NOTICED THAT ALL OF MY REAR BRAKE LIGHTS WERE NOT WORKING. THERE WAS NO WARNING LIGHT ON MY DASH TO NOTIFY ME OF THIS PROBLEM. I TOOK MY CAR TO THE SERVICE DEPARTMENT OF A HYUNDAI DEALERSHIP AND THEY SAID A DIODE HAD FAILED. I WAS PULLED OVER BY A POLICEMAN ABOUT 2 YEARS AGO FOR THE SAME ISSUE (THERE WAS NO INDICATION ON MY DASH OF THE NON-WORKING BRAKE LIGHTS AT THAT TIME EITHER). SO, THIS PROBLEM HAS HAPPENED TWICE IN THE FOUR YEARS THAT I'VE DRIVEN THIS CAR. THIS IS A SAFETY PROBLEM BECAUSE WHEN NO REAR BRAKE LIGHTS ILLUMINATE THEN I'M AT RISK FOR A REAR-END COLLISION. THERE SHOULD BE AN INDICATOR LIGHT ON THE DASH THAT INFORMS THE DRIVER OF NON-WORKING REAR BRAKE LIGHTS. ESPECIALLY WHEN NO REAR BREAK LIGHTS ILLUMINATE (AS WAS MY SITUATION). *TR
NOTICED THAT THE HEAD LIGHTS SHUT OFF FOR A COUPLE OF SECONDS WHEN MAKING A TURN ONTO A RAMP ON AN INTERSTATE. SEEMED TO HAPPEN WHEN THE TURN SIGNAL WAS OPERATED AND HAS REPEATED A DOZEN OR SO TIMES SINCE THE FIRST OCCURRENCE, BUT CAN GO WEEKS TO MONTHS BETWEEN INCIDENTS. I THINK THAT THE HEAD LIGHT SELECTIONS SWITCH WAS SET T…
Read full complaint
NOTICED THAT THE HEAD LIGHTS SHUT OFF FOR A COUPLE OF SECONDS WHEN MAKING A TURN ONTO A RAMP ON AN INTERSTATE. SEEMED TO HAPPEN WHEN THE TURN SIGNAL WAS OPERATED AND HAS REPEATED A DOZEN OR SO TIMES SINCE THE FIRST OCCURRENCE, BUT CAN GO WEEKS TO MONTHS BETWEEN INCIDENTS. I THINK THAT THE HEAD LIGHT SELECTIONS SWITCH WAS SET TO "ON" AT THE TIME AS I HAVE NOT NOTICED THIS TO OCCUR WHEN SET TO "AUTO." *TR
WHEN USING TURN SIGNAL AT NIGHT THE HEADLIGHTS TURN OFF FOR A FEW SECONDS. ITS DONE IT SINCE ALMOST NEW INTERMITTENTLY. *TR
Official recalls
314V713000 · Exterior Lighting:brake Lights:switch
Nov 7, 2014
Hyundai Motor America (Hyundai) is recalling certain 2009-2011 Hyundai Genesis vehicles manufactured April 30, 2008, to November 21, 2010, and 2011 Hyundai Equus vehicles manufactured July 31, 2010, to November 21, 2010. Due to a circuit failure, the stop lamps in the affected vehicles may not illuminate.
Consequence & remedy
Consequence: A following vehicle may not recognize that the vehicle is slowing or coming to a stop if the stop lamps on the vehicle do not illuminate as expected. There is an increased risk of a rear-end crash as a result.
Remedy: Hyundai will notify owners, and dealers will repair the stop lamp switch circuit, free of charge. Hyundai issued an interim notification to owners on January 6, 2015. The recall began on March 23, 2015. Owners may contact Hyundai customer service at 1-855-671-3059. Hyundai's number for this recall is 125.
13V489000 · Service Brakes, Hydraulic:fluid
Oct 29, 2013
Hyundai is recalling certain model year 2009-2012 Genesis vehicles manufactured April 30, 2008, through March 28, 2012. The vehicles may contain brake fluid which does not protect against corrosion of the Hydraulic Electronic Control Unit (HECU).
Consequence & remedy
Consequence: If the module corrodes, reduced brake effectiveness may result, increasing the risk of a crash.
Remedy: Hyundai will notify owners and instruct them to bring their vehicle to a dealer for service. Hyundai will inspect the HECU module for proper operation, and will replace the modules as necessary. Hyundai will replace the factory brake fluid in those vehicles that have not previously had the factory brake fluid replaced. These repairs will be done free of charge. The recall began on December 24, 2013. Owners may contact Hyundai at 1-800-633-5151 or by email at consumeraffairs@hmausa.com. Hyundai's recall number is 114.
13V113000 · Exterior Lighting:brake Lights:switch
Apr 1, 2013
Hyundai Motor Company (Hyundai) is recalling certain model year 2006-2009 Accent, model year 2007-2011 Azera, Sonata and Sante Fe,2006-2011 Tucson, 2009-2011 Elantra Touring, 2007-2010 Elantra, 2008-2011 Veracruz, 2009-2011 Genesis, 2010-2011 Genesis Coupe, 2007-2008 Entourage, and 2006-2008 Tiburon vehicles. Originally, in April 2013, Hyundai recalled 1,059,824 model year 2007-2009 Accent and Tucson, model year 2007-2010 Elantra, model year 2007-2011 Santa Fe, model year 2008-2009 Veracruz, model year 2010-2011 Genesis Coupe, and model year 2011 Sonata vehicles. In September 2013, Hyundai informed the agency that it was adding more vehicles to this campaign, representing an additional 652,512 units. The total number of vehicles being recalled is now 1,712,336. In the affected vehicles, the stop lamp switch may malfunction. A malfunctioning stop lamp switch may cause the brake lights to not illuminate when the brake pedal is depressed or may cause an inability to deactivate the cruise control by depressing the brake pedal. Additionally, a malfunctioning stop lamp switch may also result in intermittent operation of the push-button start feature, affect the operation of the brake transmission shift interlock feature, preventing the shifter from being moved out of the PARK position and cause the Electronic Stability Control (ESC) malfunction light to illuminate.
Consequence & remedy
Consequence: Failure to illuminate the stop lamps during braking or inability to disengage the cruise control could increase the risk of a crash. Additionally, when the ignition is in the 'ON' position, the transmission shifter may be able to be moved out of Park without first applying the brake. This may lead to unintentional movement of the car which may increase the risk of a crash.
Remedy: Hyundai will notify owners, and dealers will replace the stop lamp switch, free of charge. The safety recall began on April 22, 2013. Owners may contact Hyundai at 1-800-633-5151. Hyundai's recall campaign number is 110.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE13033 · Brake Hydraulic Control Module Failure
Opened Oct 17, 2013 · Closed Apr 4, 2014
Status: closed (inferred from source dates) · Service Brakes, Hydraulic; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Additional source detail variants (3)
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Service Brakes, Hydraulic
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354