IllustrationBRAKE PEDAL DEPRESSES ALL THE WAY TO THE FLOOR. REPLACED BRAKE MASTER CYLINDER AND FLUSHED BRAKE FLUID. BRAKE PEDAL STILL DEPRESSES TO THE FLOOR. CAR HAS 46,000 MILES ON IT. ABS CENSOR IS FAULTY. NEED NEW MODULE.
2009 Hyundai Genesis
Owner reports · Recalls · Investigations
More warning signs than most Genesis years
Owner complaints for the 2009 Hyundai Genesis are substantially higher than the model-year median of 109.
About this comparison →How this year compares
Owner complaints by model year
Compare all Genesis years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
290–25K
4725–50K
6050–75K
3675–100K
27100–150K
8150K+
207 reports with mileage · 27 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Service Brakes. Review the 110 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 28 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Exterior Lighting. Review the 24 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
15 crash reports2 fire reports3 injury reports
What owners actually said
234 reportsTHE TRUNK CLOSES HARD, AND WON'T STAY UP WHEN RAISED..ALMOST LOST SOME FINGERS VEHICLE WAS OFF AND PARKED IN MY GARAGE
TL* THE CONTACT OWNS A 2009 HYUNDAI GENESIS. WHILE APPROACHING A STOP, THE ENGINE REVVED AND THE BRAKE PEDAL DEPRESSED SLIGHTLY. THE CONTACT PLACED THE GEAR IN NEUTRAL AND WAS ABLE TO CONTROL THE VEHICLE. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE FAILURE RECURRED THREE TIMES. THE VEHICLE WAS TAKEN TO THE DEALER (KEY HYUN…
Read full complaint
TL* THE CONTACT OWNS A 2009 HYUNDAI GENESIS. WHILE APPROACHING A STOP, THE ENGINE REVVED AND THE BRAKE PEDAL DEPRESSED SLIGHTLY. THE CONTACT PLACED THE GEAR IN NEUTRAL AND WAS ABLE TO CONTROL THE VEHICLE. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE FAILURE RECURRED THREE TIMES. THE VEHICLE WAS TAKEN TO THE DEALER (KEY HYUNDAI IN JACKSONVILLE, FL, 904-642-6060), BUT THE FAILURE WAS NOT DUPLICATED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND SENT AN INVESTIGATOR WHO WAS UNABLE TO DUPLICATE THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS APPROXIMATELY 26,350. *TT CONSUMER STATED THERE WERE NEVER ANY CRASHES OR INJURIES AS I WAS ABLE TO MAINTAIN CONTROL BY SHIFTING INTO NEUTRAL. UPDATED 9/18/18*JB
TL* THE CONTACT OWNS A 2009 HYUNDAI GENESIS. THE CONTACT STATED THAT THE BRAKE PEDAL FELT ABNORMAL WHEN DEPRESSED AND THE STOPPING DISTANCE WAS INCREASED. THE VEHICLE WAS TAKEN TO PARAMUS HYUNDAI DEALER LOCATED AT 234 NJ4, PARAMUS, NJ FOR DIAGNOSTIC TESTING. THE MANUFACTURER WAS NOT NOTIFIED. THE VIN WAS NOT PROVIDED. THE FAILUR…
Read full complaint
TL* THE CONTACT OWNS A 2009 HYUNDAI GENESIS. THE CONTACT STATED THAT THE BRAKE PEDAL FELT ABNORMAL WHEN DEPRESSED AND THE STOPPING DISTANCE WAS INCREASED. THE VEHICLE WAS TAKEN TO PARAMUS HYUNDAI DEALER LOCATED AT 234 NJ4, PARAMUS, NJ FOR DIAGNOSTIC TESTING. THE MANUFACTURER WAS NOT NOTIFIED. THE VIN WAS NOT PROVIDED. THE FAILURE MILEAGE WAS APPROXIMATELY 100,151.
TRUNK CLOSES HARD, ALMOST TOOK MY HAND......RADIO.CD DECK HAS ALWAYS HAD A WIRING PROBLEM, AND THEY SAY THEY FIXED IT
CAR DRIVING ON HIGH AND WHEN TRY TO STOP THROUGH TOLL BOOTH IT WAS NO BRAKE AND HIT TO THE FLOOR. IT GOT SOME BRAKE AFTER HIT TO THE FLOOR, AND AFTER THAT I PUMPED THE BRAKE COUPLE TIMES AND AFTER ABOUT HIT TO THE FLOOR 4 TIMES, IT FINALLY CAME BACK WITH NORMAL. THIS HAPPENED TWICE IN THE PAST MONTH. DOES NOT HAPPEN ALL THE T…
Read full complaint
CAR DRIVING ON HIGH AND WHEN TRY TO STOP THROUGH TOLL BOOTH IT WAS NO BRAKE AND HIT TO THE FLOOR. IT GOT SOME BRAKE AFTER HIT TO THE FLOOR, AND AFTER THAT I PUMPED THE BRAKE COUPLE TIMES AND AFTER ABOUT HIT TO THE FLOOR 4 TIMES, IT FINALLY CAME BACK WITH NORMAL. THIS HAPPENED TWICE IN THE PAST MONTH. DOES NOT HAPPEN ALL THE TIME. I HAD THE RECALL 114 DONE 4 YEARS AGO BUT WAS JUST REPLACED BRAKE FLUID, THE HECU WAS NOT REPLACED.
WIPER MOTOR SUDDENLY STOPPED WORKING. NO PRIOR ISSUES, JUST SUDDENLY STOPPED WORKING. HAVE READ ON INTERNET THIS HAS BEEN REPORTED AND TYPICALLY BLADES WILL OPERATE IF PUT IN LO POSITION BUT IT'S NOT WORKING IN MY INCIDENT! THEY WON'T WORK AT ALL.
THE ISSUE IS THAT THIS VEHICLE LOSSES ACCELERATION AND CANNOT BE OPERATOR CORRECTED WHILE DRIVING. THIS IS A MAJOR SAFETY ISSUE
MY BRAKE LIGHTS WILL NOT COME ON WHEN I PRESS THE BRAKE PEDAL. I HAVE HAD THE FUSES CHECKED AND THEY ARE ALL WORKING. I CONTACTED MY LOCAL HYUNDAI DEALERSHIP AFTER RESEARCHING THE RECALL ON THE BRAKE LIGHT SWITCH. THEY WILL NOT PERFORM THE RECALL BECAUSE THEY SAID IT WAS ALREADY DONE TWICE. BUT THERE IS OBVIOUSLY A PROBLE IF ITS…
Read full complaint
MY BRAKE LIGHTS WILL NOT COME ON WHEN I PRESS THE BRAKE PEDAL. I HAVE HAD THE FUSES CHECKED AND THEY ARE ALL WORKING. I CONTACTED MY LOCAL HYUNDAI DEALERSHIP AFTER RESEARCHING THE RECALL ON THE BRAKE LIGHT SWITCH. THEY WILL NOT PERFORM THE RECALL BECAUSE THEY SAID IT WAS ALREADY DONE TWICE. BUT THERE IS OBVIOUSLY A PROBLE IF ITS HAPPENING AGAIN.
TL* THE CONTACT OWNS A 2009 HYUNDAI GENESIS. WHILE THE VEHICLE WAS STOPPED AT A TRAFFIC LIGHT, THE ENGINE STALLED WITHOUT WARNING. THE VEHICLE WAS ABLE TO RESTART. THE FAILURE OCCURRED TWICE. THE VEHICLE WAS TAKEN TO A LOCAL DEALER (GOSCH HYUNDAI 100 CARRIAGE CIRCLE, HEMET, CA, 92545), BUT THE CAUSE OF THE FAILURE COULD NOT BE D…
Read full complaint
TL* THE CONTACT OWNS A 2009 HYUNDAI GENESIS. WHILE THE VEHICLE WAS STOPPED AT A TRAFFIC LIGHT, THE ENGINE STALLED WITHOUT WARNING. THE VEHICLE WAS ABLE TO RESTART. THE FAILURE OCCURRED TWICE. THE VEHICLE WAS TAKEN TO A LOCAL DEALER (GOSCH HYUNDAI 100 CARRIAGE CIRCLE, HEMET, CA, 92545), BUT THE CAUSE OF THE FAILURE COULD NOT BE DETERMINED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED AND ADVISED THE CONTACT TO SCHEDULE AN APPOINTMENT WITH THE LOCAL DEALER FOR DIAGNOSTIC TESTING. THE FAILURE MILEAGE WAS APPROXIMATELY 40,000. THE VIN WAS NOT AVAILABLE.
Official recalls
314V713000 · Exterior Lighting:brake Lights:switch
Nov 7, 2014
Hyundai Motor America (Hyundai) is recalling certain 2009-2011 Hyundai Genesis vehicles manufactured April 30, 2008, to November 21, 2010, and 2011 Hyundai Equus vehicles manufactured July 31, 2010, to November 21, 2010. Due to a circuit failure, the stop lamps in the affected vehicles may not illuminate.
Consequence & remedy
Consequence: A following vehicle may not recognize that the vehicle is slowing or coming to a stop if the stop lamps on the vehicle do not illuminate as expected. There is an increased risk of a rear-end crash as a result.
Remedy: Hyundai will notify owners, and dealers will repair the stop lamp switch circuit, free of charge. Hyundai issued an interim notification to owners on January 6, 2015. The recall began on March 23, 2015. Owners may contact Hyundai customer service at 1-855-671-3059. Hyundai's number for this recall is 125.
13V489000 · Service Brakes, Hydraulic:fluid
Oct 29, 2013
Hyundai is recalling certain model year 2009-2012 Genesis vehicles manufactured April 30, 2008, through March 28, 2012. The vehicles may contain brake fluid which does not protect against corrosion of the Hydraulic Electronic Control Unit (HECU).
Consequence & remedy
Consequence: If the module corrodes, reduced brake effectiveness may result, increasing the risk of a crash.
Remedy: Hyundai will notify owners and instruct them to bring their vehicle to a dealer for service. Hyundai will inspect the HECU module for proper operation, and will replace the modules as necessary. Hyundai will replace the factory brake fluid in those vehicles that have not previously had the factory brake fluid replaced. These repairs will be done free of charge. The recall began on December 24, 2013. Owners may contact Hyundai at 1-800-633-5151 or by email at consumeraffairs@hmausa.com. Hyundai's recall number is 114.
13V113000 · Exterior Lighting:brake Lights:switch
Apr 1, 2013
Hyundai Motor Company (Hyundai) is recalling certain model year 2006-2009 Accent, model year 2007-2011 Azera, Sonata and Sante Fe,2006-2011 Tucson, 2009-2011 Elantra Touring, 2007-2010 Elantra, 2008-2011 Veracruz, 2009-2011 Genesis, 2010-2011 Genesis Coupe, 2007-2008 Entourage, and 2006-2008 Tiburon vehicles. Originally, in April 2013, Hyundai recalled 1,059,824 model year 2007-2009 Accent and Tucson, model year 2007-2010 Elantra, model year 2007-2011 Santa Fe, model year 2008-2009 Veracruz, model year 2010-2011 Genesis Coupe, and model year 2011 Sonata vehicles. In September 2013, Hyundai informed the agency that it was adding more vehicles to this campaign, representing an additional 652,512 units. The total number of vehicles being recalled is now 1,712,336. In the affected vehicles, the stop lamp switch may malfunction. A malfunctioning stop lamp switch may cause the brake lights to not illuminate when the brake pedal is depressed or may cause an inability to deactivate the cruise control by depressing the brake pedal. Additionally, a malfunctioning stop lamp switch may also result in intermittent operation of the push-button start feature, affect the operation of the brake transmission shift interlock feature, preventing the shifter from being moved out of the PARK position and cause the Electronic Stability Control (ESC) malfunction light to illuminate.
Consequence & remedy
Consequence: Failure to illuminate the stop lamps during braking or inability to disengage the cruise control could increase the risk of a crash. Additionally, when the ignition is in the 'ON' position, the transmission shifter may be able to be moved out of Park without first applying the brake. This may lead to unintentional movement of the car which may increase the risk of a crash.
Remedy: Hyundai will notify owners, and dealers will replace the stop lamp switch, free of charge. The safety recall began on April 22, 2013. Owners may contact Hyundai at 1-800-633-5151. Hyundai's recall campaign number is 110.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE13033 · Brake Hydraulic Control Module Failure
Opened Oct 17, 2013 · Closed Apr 4, 2014
Status: closed (inferred from source dates) · Service Brakes, Hydraulic; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Additional source detail variants (3)
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Service Brakes, Hydraulic
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354