IllustrationI HAVE TWO CRACKS ON MY DASH ONE AT THE PASSENGER SIDE AIR BAG IT IS ABOUT ONE INCH LONG.THE OTHER CRACKS IS MUCH LONGER.IF IS ON THE DRIVERS SIDE NEAR THE AREA THAT IS HUMPED UP AT THE STEERING WHEEL. WHEN I BOUGHT THIS CAR THE CRACKS WERE VERY SMALL THE ONE NEAR THE STEERING WHEEL JUST KEEPS GETTING BIGGER!
2011 GMC Yukon
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2011 GMC Yukon do not stand out strongly from the model-year median of 103.
About this comparison →How this year compares
Owner complaints by model year
Compare all Yukon years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
40–25K
2025–50K
1950–75K
1675–100K
20100–150K
6150K+
85 reports with mileage · 73 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 79 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 27 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 13 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
2 crash reports0 fire reports2 injury reports
Structure complaints
27 reportsTL* THE CONTACT OWNS A 2011 GMC YUKON. THE CONTACT STATED THAT THE DASHBOARD WAS CRACKED AROUND THE PASSENGER SIDE AIR BAG AREA THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 47,000. UPDATED 06/02/17*LJ THE CONSUMER STATED THE MANUFACTURER WAS…
Read full complaint
TL* THE CONTACT OWNS A 2011 GMC YUKON. THE CONTACT STATED THAT THE DASHBOARD WAS CRACKED AROUND THE PASSENGER SIDE AIR BAG AREA THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 47,000. UPDATED 06/02/17*LJ THE CONSUMER STATED THE MANUFACTURER WAS NOTIFIED AND OFFERED TO PAY HALF OF THE REPAIR COSTS. THE CONSUMER ACCEPTED. UPDATED 10/19/2017*JS
TL* THE CONTACT OWNS A 2011 GMC YUKON. UPON ENTERING THE VEHICLE, THE CONTACT NOTICED TWO CRACKS IN THE DASHBOARD ON THE DRIVER SIDE BEHIND THE STEERING WHEEL. THE CRACKS EXPANDED OVER TIME. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIFIED. THE FAILURE MILEAGE WAS APPROXIMATELY 130,000. UPDATED 02/22/2017…
Read full complaint
TL* THE CONTACT OWNS A 2011 GMC YUKON. UPON ENTERING THE VEHICLE, THE CONTACT NOTICED TWO CRACKS IN THE DASHBOARD ON THE DRIVER SIDE BEHIND THE STEERING WHEEL. THE CRACKS EXPANDED OVER TIME. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIFIED. THE FAILURE MILEAGE WAS APPROXIMATELY 130,000. UPDATED 02/22/2017*CT
I FIRST NOTICED A CRACK ON THE DASH IN FRONT ON THE DRIVERS SIDE. SINCE NOTICING THE FIRST CRACK, OTHER CRACKS HAVE DEVELOPED.
2011 GMC YUKON. CONSUMER WRITES IN REGARDS TO REPLACEMENT PARTS NOT AVAILABLE TO REPAIR FRONT PASSENGER AIRBAG RECALL, DEALERSHIP REFUSES TO REPAIR MULTIPLE CRACKS IN DASHBOARD. *SMD
2 CRACKS IN THE DASHBOARD. ONE CRACK IS LEADING TO THE PASSENGER SIDE AIRBAG - CAUSING A SAFETY RISK.
THE DASH COVER IS CRACKING AND IS BROKEN. THIS IS HAPPENING CLOSE TO THE PASSENGER AIRBAG. I'M JUST WAITING FOR THE AIRBAG TO EXPLODE WHILE I AM DRIVING. THIS IS SO UNSAFE!! MY KIDS ARE IN DANGER.
I'M A 2011GMC YUKON OWNER THAT HAS A CRACKED DASH THAT IN ONLY A MATTER OF TIME IS GOING TO AFFECT THE AIR BAG. WHEN I REACHED OUT TO GMC, THEY TOLD THAT I WOULD HAVE TO WAIT FOR AN ACCIDENT TO HAPPEN BEFORE THEY WOULD LOOK INTO THE PROBLEM.
OUR DASHBOARD CRACKED ON A 3 YEAR OLD CAR - THE LOCAL DEALER "REPAIRED" IT AND THE REPAIR LASTED ALL OF A DAY. THE CRACK GOT PROGRESSIVELY BIGGER AND GM REFUSED TO COVER ANY OF THE COST TO REPLACE, TELLING US OUR ONLY OPTION WAS TO REPLACE THE ENTIRE DASH AT A COST OF OVER $1200. WE HAVE HAD IT PATCHED BY A LOCAL REPAIR PLACE …
Read full complaint
OUR DASHBOARD CRACKED ON A 3 YEAR OLD CAR - THE LOCAL DEALER "REPAIRED" IT AND THE REPAIR LASTED ALL OF A DAY. THE CRACK GOT PROGRESSIVELY BIGGER AND GM REFUSED TO COVER ANY OF THE COST TO REPLACE, TELLING US OUR ONLY OPTION WAS TO REPLACE THE ENTIRE DASH AT A COST OF OVER $1200. WE HAVE HAD IT PATCHED BY A LOCAL REPAIR PLACE WHO DID A BETTER JOB THAN THE DEALER, BUT THE DASH STILL VIBRATES TO THE POINT OF SHAKING AND THE PATCH IS NOW COMING APART AGAIN. THE ACTUAL CRACK IS NOW OVER A 1/2" BIG. WE ARE WORRIED ABOUT THE AIRBAGS DEPLOYING AND THE SHARP PLASTIC CAUSING SERIOUS INJURY.
TL* THE CONTACT OWNS A 2011 GMC YUKON. WHILE ATTEMPTING TO OPEN THE REAR PASSENGER SIDE DOOR, THE DOOR HANDLE DETACHED FROM THE DOOR. THE VEHICLE WAS TAKEN TO A DEALER WHERE IT WAS DIAGNOSED THAT THE DOOR HANDLE NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAI…
Read full complaint
TL* THE CONTACT OWNS A 2011 GMC YUKON. WHILE ATTEMPTING TO OPEN THE REAR PASSENGER SIDE DOOR, THE DOOR HANDLE DETACHED FROM THE DOOR. THE VEHICLE WAS TAKEN TO A DEALER WHERE IT WAS DIAGNOSED THAT THE DOOR HANDLE NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 24,000.
Official recalls
521V050000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2007-2011 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL, and 2009-2011 Chevrolet Silverado 2500, Silverado 3500, GMC Sierra 2500 and Sierra 3500 vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 22, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on March 1, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328760.
21V054000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally GM is recalling certain 2011-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, Yukon XL and 2011-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Additionally, GM is recalling certain 2010-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL and 2010-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 25, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed to 40 VIN owners on May 11, 2021. A second owner notification letter was mailed to all other owners on January 24, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328800.
14V827000 · Electrical System:ignition
Dec 30, 2014
General Motors LLC (GM) is recalling certain model year 2011-2012 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado HD, Silverado LD, Suburban, Tahoe, GMC Sierra LD, Sierra HD, Yukon, and Yukon XL vehicles. In the affected vehicles, the ignition lock actuator may bind, making turning the key difficult or causing the ignition to get stuck in the "Start" position.
Consequence & remedy
Consequence: If stuck in the "Start" position, the ignition may suddenly snap back into the "Accessory" position, causing a loss of engine, steering, and braking power, increasing the risk of a vehicle crash. If the vehicle is in a crash, the air bags may not deploy, increasing the risk of occupant injury.
Remedy: GM will notify owners, and dealers will inspect and replace the ignition lock housing, as necessary, free of charge. The recall began on February 12, 2015. Owners may contact GM customer service at 1-800-458-8006 (Cadillac), 1-800-222-1020 (Chevrolet), or 1-800-462-8782 (GMC). GM's number for this recall is 14696 for the original equipment, and 14912 for the service replacement parts.
11V339000 · Steering:linkages
Jun 28, 2011
GM IS RECALLING CERTAIN MODEL YEAR 2011CADILLAC ESCALADE, ESCALADE ESV; CHEVROLET SILVERADO HD, SILVERADO LD, SUBURBAN, TAHOE; AND GMC SIERRA HD, SIERRA LD, YUKON, AND YUKON XL VEHICLES. THE INTERMEDIATE STEERING SHAFT ATTACHING BOLTS MAY NOT HAVE BEEN TIGHTENED TO THE PROPER SPECIFICATION.
Consequence & remedy
Consequence: THIS COULD ALLOW THE JOINTS TO SEPARATE, AND THE DRIVER COULD EXPERIENCE LOSS OF STEERING INCREASING THE RISK OF A CRASH.
Remedy: GM DEALERS WILL INSPECT AND ENSURE THAT THE INTERMEDIATE STEERING SHAFT BOLTS ARE TIGHTENED TO THE PROPER SPECIFICATION. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR ABOUT JULY 13, 2011. OWNERS MAY CONTACT CADILLAC AT 1-800-458-8006, CHEVROLET AT 1-800-630-2438 AND GMC AT 1-866-996-9463.
11V007000 · Suspension:rear:axle:spindle
Jan 6, 2011
GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2011 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT; CHEVROLET AVALANCHE, COLORADO, EXPRESS, SILVERADO, SUBURBAN, TAHOE; AND GMC CANYON, SIERRA, SAVANA, YUKON AND YUKON XL VEHICLES. THE REAR AXLE CROSS PINS WERE NOT PROPERLY HEAT TREATED AND COULD FRACTURE AND BECOME DISPLACED WITHIN THE REAR AXLE. SHOULD THE PIN SHIFT OUT OF POSITION, IT COULD CREATE AN INTERFERENCE CONDITION AND CAUSE THE REAR AXLE TO LOCK.
Consequence & remedy
Consequence: THE DRIVER MAY NOT BE ABLE TO MAINTAIN DIRECTIONAL CONTROL OF THE VEHICLE AND A CRASH COULD OCCUR WITHOUT WARNING.
Remedy: DEALERS WILL INSTALL A NEW REAR AXLE CROSS PIN FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 11, 2011. OWNERS MAY CONTACT CADILLAC AT 1-866-982-2339, CHEVROLET AT 1-800-630-2438, GMC AT 1-866-996-9463 AND AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.