IllustrationTAKATA AIR BAG RECALL
2008 GMC Yukon Xl
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2008 GMC Yukon Xl do not stand out strongly from the model-year median of 68.
About this comparison →How this year compares
Owner complaints by model year
Compare all Yukon Xl years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
40–25K
825–50K
250–75K
375–100K
5100–150K
13150K+
35 reports with mileage · 34 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 42 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 11 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 8 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
2 crash reports1 fire reports5 injury reports
Air Bags complaints
42 reportsTL* THE CONTACT OWNS A 2008 GMC YUKON XL. WHILE DRIVING 65 MPH, THE CONTACT NOTICED THAT ANOTHER VEHICLE WAS SWERVING TOWARDS HER VEHICLE. THE CONTACT HAD TO DEPRESS THE ACCELERATOR PEDAL TO INCREASE SPEED AND AVOID A COLLISION; HOWEVER, THE OTHER VEHICLE LOST CONTROL AND CRASHED INTO THE CONTACT'S VEHICLE. THE FRONT FRAME, FRON…
Read full complaint
TL* THE CONTACT OWNS A 2008 GMC YUKON XL. WHILE DRIVING 65 MPH, THE CONTACT NOTICED THAT ANOTHER VEHICLE WAS SWERVING TOWARDS HER VEHICLE. THE CONTACT HAD TO DEPRESS THE ACCELERATOR PEDAL TO INCREASE SPEED AND AVOID A COLLISION; HOWEVER, THE OTHER VEHICLE LOST CONTROL AND CRASHED INTO THE CONTACT'S VEHICLE. THE FRONT FRAME, FRONT PASSENGER SIDE, AND REAR FRAME OF THE CONTACT'S VEHICLE WERE DAMAGED. THE AIR BAGS FAILED TO DEPLOY. THE CONTACT WAS KNOCKED UNCONSCIOUS AND REQUIRED MEDICAL ATTENTION. A POLICE REPORT WAS FILED. THE VEHICLE WAS TOWED FROM THE SCENE. THE CONTACT STATED THAT THE VEHICLE WAS INSPECTED BY A MECHANIC FRIEND WHO CONFIRMED THE AIR BAGS FAILED TO DEPLOY. THE VEHICLE WAS NOT REPAIRED. THE DEALER WAS NOT CONTACTED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE AND A CASE WAS OPENED. THE CONTACT STATED THAT THE CASE HAD CLOSED. THE APPROXIMATE FAILURE MILEAGE WAS 150,000.
TL* TAKATA RECALL. THE CONTACT OWNS A 2008 GMC YUKON XL. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V383000 (AIR BAGS); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE DEALER WAS NOT CONTACTED. THE MA…
Read full complaint
TL* TAKATA RECALL. THE CONTACT OWNS A 2008 GMC YUKON XL. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V383000 (AIR BAGS); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE DEALER WAS NOT CONTACTED. THE MANUFACTURER WAS NOTIFIED ON SEVERAL OCCASIONS AND WAS NOT ABLE TO CONFIRM WHEN THE PARTS WERE TO BECOME AVAILABLE. THE CONTACT WAS PROVIDED CASE NUMBER: 8-3322063945. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.
TL* TAKATA RECALL. THE CONTACT OWNS A 2008 GMC YUKON XL. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V381000 (AIR BAGS). THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE CONTACT CALLED FIKES CHEVROLET AT (205) 9…
Read full complaint
TL* TAKATA RECALL. THE CONTACT OWNS A 2008 GMC YUKON XL. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V381000 (AIR BAGS). THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE CONTACT CALLED FIKES CHEVROLET AT (205) 921-2197 (LOCATED AT 771 MILITARY ST N, HAMILTON, AL 35570) AND WAS INFORMED THAT THE RECALL HAD NOT STARTED AND THE CONTACT WOULD HAVE TO WAIT FOR A NOTICE. THE MANUFACTURER WAS NOT NOTIFIED. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.
TAKATA RECALL I HAVE REQUESTED THE DEALER TO CHANGE THE AIRBAG BECAUSE OF THE RECALL FOR A LONG TIME AND THE ANSWER IS THAT PARTS ARE NOT AVAILABLE FROM GMC. I AM CONCERNED FOR MY SAFETY AND MY FAMILY. NHTSA RECALL #16V381. MANUFACTURER RECALL NUMBER:2049151 LAST SERVICE AND REQUEST WAS AROUND NOVEMBER TIME FRAM.
WE WERE NOTIFIED, AS WE WERE GETTING SERVICE DONE ON OUR VEHICLE, THAT THERE WAS AN AIRBAG RECALL ON THE PASSENGER SIDE. WE WERE NEVER INFORMED ABOUT ANY IMPENDING RECALL. WE THEN CONTACTED OUR DEALER, AND WE WERE TOLD THAT AS OF MAY 2016, GMC DID NOT YET HAVE A SOLUTION TO THE PROBLEM. NO FURTHER WORD ON ANY CORRECTIVE ACTIO…
Read full complaint
WE WERE NOTIFIED, AS WE WERE GETTING SERVICE DONE ON OUR VEHICLE, THAT THERE WAS AN AIRBAG RECALL ON THE PASSENGER SIDE. WE WERE NEVER INFORMED ABOUT ANY IMPENDING RECALL. WE THEN CONTACTED OUR DEALER, AND WE WERE TOLD THAT AS OF MAY 2016, GMC DID NOT YET HAVE A SOLUTION TO THE PROBLEM. NO FURTHER WORD ON ANY CORRECTIVE ACTION TO DATE.
TAKATA RECALL INCOMPLETE - NO PARTS AVAILABLE
TL* TAKATA RECALL. THE CONTACT OWNS A 2008 GMC YUKON XL. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V383000 (AIR BAGS). THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. DAVE SINCLAIR BUICK GMC (5655 SOUTH LINDBERGH…
Read full complaint
TL* TAKATA RECALL. THE CONTACT OWNS A 2008 GMC YUKON XL. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V383000 (AIR BAGS). THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. DAVE SINCLAIR BUICK GMC (5655 SOUTH LINDBERGH BLVD, ST LOUIS, MO 63123, 314-842-4200) WAS CONTACTED AND CONFIRMED THAT THE PARTS WERE NOT AVAILABLE FOR THE RECALL REMEDY. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE AND WAS NOT ABLE TO CONFIRM WHEN THE PARTS WOULD BE AVAILABLE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE. THE FAILURE MILEAGE WAS 155,000.
TAKATA RECALL REPLACEMENT PART NOT AVAILABLE.
DEALERSHIP IS REFUSING TO REPAIR THE RECALL AIR BAG PARTS. THEY SAY THEY DON'T HAVE THEM TO DO THE REPAIR.
Official recalls
421V050000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2007-2011 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL, and 2009-2011 Chevrolet Silverado 2500, Silverado 3500, GMC Sierra 2500 and Sierra 3500 vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 22, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on March 1, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328760.
21V052000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2009 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 23, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on September 20, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, Cadillac customer service at 1-800-458-8006, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328780.
10V240000 · Electrical System
Jun 4, 2010
GM IS RECALLING CERTAIN MODEL YEAR 2006-2009 BUICK, LUCERNE; CADILLAC DTS; HUMMER H2; MODEL YEAR 2008-2009 BUICK ENCLAVE; CADILLAC CTS; MODEL YEAR 2007-2009 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT; CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE; GMC ACADIA, SIERRA, YUKON, YUKON XL; SATURN OUTLOOK; AND MODEL YEAR 2009 CHEVROLET TRAVERSE VEHICLES EQUIPPED WITH A HEATED WASHER FLUID SYSTEM (HWFS). A RECALL WAS IMPLEMENTED IN 2008 TO ADD A FUSE TO THE CONTROL CIRCUIT HARNESS TO ADDRESS THE POTENTIAL CONSEQUENCES OF A PRINTED CIRCUIT BOARD (PCB) ELECTRICAL SHORT. HOWEVER, THERE HAVE BEEN NEW REPORTS OF THERMAL INCIDENTS ON HWFS MODULES AFTER THIS IMPROVEMENT WAS INSTALLED. THESE INCIDENTS RESULTED FROM A NEW FAILURE MODE ATTRIBUTED TO THE DEVICE'S THERMAL PROTECTION FEATURE. THE SIGNIFICANCE VARIES FROM MINOR DISTORTION TO CONSIDERABLE MELTING OF THE PLASTIC AROUND THE HWFS FLUID CHAMBER.
Consequence & remedy
Consequence: IT IS POSSIBLE FOR THE HEATED WASHER MODULE TO IGNITE AND A FIRE MAY OCCUR.
Remedy: DEALERS WILL PERMANENTLY DISABLE AND REMOVE THE HEATED WASHER FLUID MODULE. AN UPDATED PAGE FOR THE OWNER MANUAL WILL BE PROVIDED AND INSERTED IN THE OWNER MANUAL TO DOCUMENT THAT THE FEATURE HAS BEEN PERMANENTLY DISABLED AND REMOVED FROM THE VEHICLE. THE SAFETY RECALL BEGAN ON JUNE 11, 2010. OWNERS MAY CONTACT BUICK AT 1-866-608-8080, CADILLAC AT 1-866-982-2339, CHEVROLET AT 1-800-630-2438, SATURN AT 1-800-972-8876, GMC AT 1-866-996-9463 AND HUMMER AT 1-800-732-5493 OR AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.
08V441000 · Electrical System
Aug 28, 2008
GM IS RECALLING 857,735 MY 2006-2008 BUICK LUCERNE; CADILLAC DTS; HUMMER H2; MY 2007-2008 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT; CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE; GMC ACADIA, SIERRA, YUKON, YUKON XL, SATURN OUTLOOK; AND MY 2008 BUICK ENCLAVE VEHICLES EQUIPPED WITH A HEATED WIPER WASHER FLUID SYSTEM. A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WASHER FLUID HEATER MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE.
Consequence & remedy
Consequence: THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR, OR CAUSE SMOKE INCREASING THE RISK OF A FIRE.
Remedy: DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE FREE OF CHARGE. THE RECALL BEGAN ON SEPTEMBER 12, 2008. OWNERS MAY CONTACT BUICK AT 1-866-608-8080; CADILLAC AT 1-800-982-2339 OR HTTP://WWW.CADILLAC.COM; CHEVROLET AT 1-800-630-2438; SATURN AT 1-800-972-8876 OR HTTP://WWW.SATURN.COM, GMC AT 1-866-996-9436; OR HUMMER AT 1-800-732-5493; OR THROUGH THEIR WEBSITE AT <A HREF=HTTP://WWW.GMOWNERCENTER.COM>HTTP://WWW.GMOWNERCENTER.COM</A> .
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.