IllustrationI have a complaint about the recall response from both nasal and gm. I feel the cure is substandard. Why not just put new transmission control modules in to correct this problem. Very disappointed
2020 GMC Sierra 3500
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all Sierra 3500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 10 of 51 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 19 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 9 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 7 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
4 crash reports2 fire reports1 injury reports
What owners actually said
51 reportsThere is a current safety recall N232426400 on GMC pickups including the year of my truck. GMC is saying that my VIN is not covered by the recall. However, I have the multi-pro tailgate and it came open about 6 months ago on its own as i was backing up and it caused me to run into my trailer with the tailgate. I put my tai…
Read full complaint
There is a current safety recall N232426400 on GMC pickups including the year of my truck. GMC is saying that my VIN is not covered by the recall. However, I have the multi-pro tailgate and it came open about 6 months ago on its own as i was backing up and it caused me to run into my trailer with the tailgate. I put my tailgate up after moving my truck from under my trailer and then when i went to back up somehow the tailgate popped open and i didnt know and it contacted the top of tailgate while it was down.
driving 65mph on interstate, attempted to change lanes to pass slower vehicle and pressed upon accelerator pedal...truck violently skidded to a stop and sent me onto shoulder, many vehicles behind me swerved to avoid my vehicle. GM wont repair and says since they cant replicate its not really happening. this has happened twice…
Read full complaint
driving 65mph on interstate, attempted to change lanes to pass slower vehicle and pressed upon accelerator pedal...truck violently skidded to a stop and sent me onto shoulder, many vehicles behind me swerved to avoid my vehicle. GM wont repair and says since they cant replicate its not really happening. this has happened twice in last 2 weeks.
driving approximately 50 mph when vehicle suddenly made loud bang and locked up rear brakes for 25' coming to a stop in road side ditch, numerous vehicles had to make evasive actions to avoid me and other vehicles. flat spotted tire abut no visible physical damage. sat on side of road for transmission temp to cool down then dro…
Read full complaint
driving approximately 50 mph when vehicle suddenly made loud bang and locked up rear brakes for 25' coming to a stop in road side ditch, numerous vehicles had to make evasive actions to avoid me and other vehicles. flat spotted tire abut no visible physical damage. sat on side of road for transmission temp to cool down then drove to shop without repeat. called dealer was told the earliest appt was a month away. have not been able to repeat incident so far. this has happened a few times and is becoming more frequent, mfg has tsb issued but indicates they cant assist because my warranty has expired so i will have to pay 225 per hour diagnostic fee. this is untenable and dangerous. this needs a recall and repair ASAP.
driving 45 mph westbound i70 at eisenhower tunnel, vefhicle made loud bang, brakes locked up momentarily slowing vehicle to around 25mph. multiple vehicles had to make evasive manuevers to avoid collision. vehicle released after a 15FT skid. pulled over to safety and inspect for damage, tires were falt spotted but no damage was …
Read full complaint
driving 45 mph westbound i70 at eisenhower tunnel, vefhicle made loud bang, brakes locked up momentarily slowing vehicle to around 25mph. multiple vehicles had to make evasive manuevers to avoid collision. vehicle released after a 15FT skid. pulled over to safety and inspect for damage, tires were falt spotted but no damage was visible. called dealer servcei and was told to make appt and set for diagnostic. service could not replicate or find damage so I was sent on my way and told if it does it again let us know. I am scared to drive this vehicle its unsafe
driving 65mph when vehicle attempted to downshift itself for no reason when instead the rear axles locked up and made a massively loud bang as if axle fell off, let off gas, smoke pouring from rear tires, skidded about 8 feet, it released then locked up 2 more times within 30 secs before I could get off road out of traffic flow.…
Read full complaint
driving 65mph when vehicle attempted to downshift itself for no reason when instead the rear axles locked up and made a massively loud bang as if axle fell off, let off gas, smoke pouring from rear tires, skidded about 8 feet, it released then locked up 2 more times within 30 secs before I could get off road out of traffic flow. mfd has a tsb for this issue(#21-NA-275 GM) not sure if its transmission or braking system Dealer service could not replicate and told me it was probably my trailer(wasnt traveling with trailer) no warnings, no codes occurred initially at 56000 mile, has happened 10 or 12 times since then. very scary, im afraid to drive or tow now that dealer mentioned trailer brakes.
Fuel Pump Driver Module
I was driving approximately 60mph pulling a trailer when the back tires locked up for approximately 2 seconds. This happened 3 times within 30 minutes. I've taken it to the GM repair shop. They have seen this happen to 3 or 4 vehicles. Due to not being able to replicate the fault it has been difficult to diagnose. They are going…
Read full complaint
I was driving approximately 60mph pulling a trailer when the back tires locked up for approximately 2 seconds. This happened 3 times within 30 minutes. I've taken it to the GM repair shop. They have seen this happen to 3 or 4 vehicles. Due to not being able to replicate the fault it has been difficult to diagnose. They are going to replace the transmission valve body hoping that will take care of the issue. This is extremely dangerous to everyone on the road when this happens. There are many forums out there that I've read and have been close to deadly accidents involving cars, trucks, RV's, and semis as they've ran off the roads. This seems to be something worth looking into and ensuring GM puts out a recall for. In my case, I am going through an extended warrant for my 2020 3500 with 112,000 miles. The warranty company wants the GM technician to replicate the fault... which isn't possible without hooking up a trailer... also very dangerous which I refuse to do until the issue if resolved. In any case, I will have to hook up a trailer once the part is replaced... praying that it won't happen again.
Vehicle will not start due to known GM issues. This failure left my family stranded in cold dark unsafe area once already. If we were in the flow of traffic or had to leave an area immediately we would have been unable too. Known GM issue, engine fault code P12A6 fault code. Bulletin: PIP5719A discusses this issue. I am being …
Read full complaint
Vehicle will not start due to known GM issues. This failure left my family stranded in cold dark unsafe area once already. If we were in the flow of traffic or had to leave an area immediately we would have been unable too. Known GM issue, engine fault code P12A6 fault code. Bulletin: PIP5719A discusses this issue. I am being told by the dealer there is a newer bulletin which advises ECM update. GM dealer is stating ECM software upgrade is required to resolve at owners expense. Owner is responsible for diagnostic fee in addition to repair costs. If the issue is not resolved vehicle may continue to experience starting failure and or other electrical problems. The night the vehicle left us stranded instrumentation was erratic and not reading properly on the instrument cluster. Very unsafe and GM should reach out to customers to inform them a software update is needed and it should not be at the expense to the consumer if the consumer is out of the bumper to bumper warranty.
Rear sliding window is leaking water into the cabin
Official recalls
826V083000 · Power Train:automatic Transmission:control Module:software; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
Feb 12, 2026
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence & remedy
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
Additional source detail variants (2)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
Power Train:automatic Transmission:control Module:software
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
24V797000 · Power Train:automatic Transmission:control Module:software; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
Oct 24, 2024
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence & remedy
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
Additional source detail variants (2)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
Power Train:automatic Transmission:control Module:software
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
24V060000 · Latches/locks/linkages:tailgate:latch
Feb 1, 2024
General Motors, LLC (GM) is recalling certain 2020-2024 Chevrolet Silverado 2500, 3500, GMC Sierra 2500 and 3500 vehicles equipped with power-unlatching tailgates. The tailgate's electronic gate-release switch may short circuit due to water intrusion, which can result in the tailgate inadvertently unlatching while the vehicle is in park.
Consequence & remedy
Consequence: An unlatched tailgate may open while driving and result in a loss of unsecured cargo, creating a road hazard and increasing the risk of a crash.
Remedy: Owners are advised to check that the tailgate is closed and latched before driving. Dealers will replace the exterior touchpad switch assemblies, free of charge. Owner notification letters were mailed May 17, 2024. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is N232426400.
20V792000 · Seat Belts; Seat Belts:critical Fasteners
Dec 17, 2020
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence & remedy
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
Additional source detail variants (2)
Seat Belts:critical Fasteners
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
Seat Belts
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
20V446000 · Air Bags:side/window:curtain:inflator
Jul 30, 2020
General Motors, LLC. (GM) is recalling certain 2020 Buick Enclave, Cadillac XT5 and XT6, Chevrolet Blazer, Silverado 1500, 2500 and 3500 and Traverse and GMC Acadia and Sierra 1500, 2500 and 3500 vehicles. The diffuser component of the Roof-Rail Air Bag (RRAB) inflator may not have been properly crimped to the inflator and could separate from the inflator during air bag deployment.
Consequence & remedy
Consequence: If the diffuser separates from the inflator during deployment, RRAB performance may be degraded, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will replace the suspect RRAB modules, free of charge. The recall began September 3, 2020. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-333-4223, or Buick customer service at 1-800-521-7300. GM's number for this recall is N202305380.
20V324000 · Latches/locks/linkages:hood:latch; Structure:body:hood
Jun 4, 2020
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles previously recalled under 20V-142. Some of the vehicles in 20V-324 were not part of Recall 20V-142 but received defect parts during another service (typically during collision repair). The hood-latch striker wires on replacement hoods installed for Safety Recall 20V-142 may not have been heat-treated properly, possibly causing them to fracture.
Consequence & remedy
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. For hoods sold over the counter, dealers will contact customers with instructions for hood replacement. The recall began July 7, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N202306490.
Additional source detail variants (2)
Latches/locks/linkages:hood:latch
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles previously recalled under 20V-142. Some of the vehicles in 20V-324 were not part of Recall 20V-142 but received defect parts during another service (typically during collision repair). The hood-latch striker wires on replacement hoods installed for Safety Recall 20V-142 may not have been heat-treated properly, possibly causing them to fracture.
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. For hoods sold over the counter, dealers will contact customers with instructions for hood replacement. The recall began July 7, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N202306490.
Structure:body:hood
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles previously recalled under 20V-142. Some of the vehicles in 20V-324 were not part of Recall 20V-142 but received defect parts during another service (typically during collision repair). The hood-latch striker wires on replacement hoods installed for Safety Recall 20V-142 may not have been heat-treated properly, possibly causing them to fracture.
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. For hoods sold over the counter, dealers will contact customers with instructions for hood replacement. The recall began July 7, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N202306490.
20V142000 · Latches/locks/linkages:hood:latch
Mar 12, 2020
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The hood-latch striker wires may not have been heat-treated properly, possibly causing them to fracture.
Consequence & remedy
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. The recall began April 13, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N192284960.
19V814000 · Seat Belts:pretensioner
Nov 14, 2019
General Motors LLC (GM) is recalling certain 2019-2020 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2020 Silverado 2500, Silverado 3500, Sierra 2500, and Sierra 3500 vehicles equipped with carpet floor covering. When the front seat belt pretensioners deploy, hot gas may vent through an opening in the pretensioner bracket, possibly igniting the carpet.
Consequence & remedy
Consequence: A vehicle fire could result if materials ignite inside the vehicle.
Remedy: GM will notify owners, and dealers will close off the opening in the pretensioner bracket, free of charge. The recall began December 13, 2019. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N192270600.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE21010 · Air Bag Malfunction
Opened Apr 9, 2021 · Closed Aug 24, 2023
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:srs Malfunction Warning Lamp/light
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Additional source detail variants (4)
Air Bags:frontal:driver Side:inflator Module
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags:frontal
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags:srs Malfunction Warning Lamp/light
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.