IllustrationThe catalytic converter failed at 93,000 miles, and 64 months. GM says it is out of warranty.
2020 GMC Sierra 2500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2020 GMC Sierra 2500 do not stand out strongly from the model-year median of 46.
About this comparison →How this year compares
Owner complaints by model year
Compare all Sierra 2500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
110–25K
225–50K
250–75K
075–100K
8100–150K
1150K+
24 reports with mileage · 50 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 13 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 12 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
1 crash reports3 fire reports1 injury reports
What owners actually said
74 reportsThe contact owns a 2020 GMC Sierra 2500. The contact stated that while driving approximately 70-80 MPH, the transmission downshifted, and the rear wheels locked up. The contact was able to coast to the side of the road. The contact was unsure if a warning light had illuminated. The vehicle was towed to the dealer, where it was d…
Read full complaint
The contact owns a 2020 GMC Sierra 2500. The contact stated that while driving approximately 70-80 MPH, the transmission downshifted, and the rear wheels locked up. The contact was able to coast to the side of the road. The contact was unsure if a warning light had illuminated. The vehicle was towed to the dealer, where it was diagnosed and determined that the transmission had failed and needed to be replaced. There were metal shavings found mixed in with the transmission fluid; however, the vehicle remained with the dealer unrepaired. The contact was informed by the dealer that the warranty had expired, and the vehicle could not be repaired. The manufacturer was notified of the failure but declined to assist in covering the cost of the repair. The failure mileage was approximately 166,000.
The contact owns a 2020 GMC Sierra 2500. The contact stated that while her husband was driving 30 MPH, the rear wheels locked up and the vehicle skidded to a complete stop. No warning lights were illuminated. The vehicle was towed to the dealer, who diagnosed a failure with the transmission. The contact was informed that the tra…
Read full complaint
The contact owns a 2020 GMC Sierra 2500. The contact stated that while her husband was driving 30 MPH, the rear wheels locked up and the vehicle skidded to a complete stop. No warning lights were illuminated. The vehicle was towed to the dealer, who diagnosed a failure with the transmission. The contact was informed that the transmission had imploded and needed to be replaced. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 24V797000 (Power Train); the VIN was included but the vehicle had not been repaired. The manufacturer was not notified of the failure. The failure mileage was 125,000.
What component or system failed or malfunctioned, and is it available for inspection upon request? - Transmission Valve Body resulting in a P0700 & P0747 code. Yes currently installed in vehicle. How was your safety or the safety of others put at risk? - When the vehicle goes into a limp mode to protect the transmission and rea…
Read full complaint
What component or system failed or malfunctioned, and is it available for inspection upon request? - Transmission Valve Body resulting in a P0700 & P0747 code. Yes currently installed in vehicle. How was your safety or the safety of others put at risk? - When the vehicle goes into a limp mode to protect the transmission and rear-wheel lock up, the truck shuttered and hard downshifted. Speed limit is restricted to 5th gear only. I've been instructed by GM to continue driving and using the vehicle until the problem happens again, knowingly putting myself and others at risk on a second failure that could happen at any time. Has the problem been reproduced or confirmed by a dealer or independent service center? Yes this is a common problem with a recall #N242454440, NHTSA 24V-797. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? Mine has been rejected by GM. Although I documented and photographed the failure codes, I cleared them from the vehicle in order to attempt to safely get to the dealer and prevent further damages. Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? At the time of failure yes, check engine light and codes from an engine monitor coinciding with the known problems. Engine speed / power was reduced to allow only 5th gear.
After the transmission recall was completed, I’m now having erratic shifting. Having the recall adding software monitoring for a hardware issue is inadequate. Now that I am out of warrentee, gm has not resolved the issue and now I am having shifting problems.
Cracks in the rear sliding window plastic upper rail glass guide causing Rear window leaking water and causing mold from water leaking. GMC has a service bulletin number 18-NA-383 knowing of this issue and not telling customers purchasing the GMC vehicle. The service bulletin was released in 2019 before purchasing the truck an…
Read full complaint
Cracks in the rear sliding window plastic upper rail glass guide causing Rear window leaking water and causing mold from water leaking. GMC has a service bulletin number 18-NA-383 knowing of this issue and not telling customers purchasing the GMC vehicle. The service bulletin was released in 2019 before purchasing the truck and they still didn't inform the customers. My child rides in the back in a car seat and now has been breathing in this mold and mildew for how long. I have had my vehicle in with Titus will Gmc in olympia multiple times for service and inspection of various recalls and still didn't inform me of this issue.
Tailgate unlatches unexpectedly. Has happened while parked and while driving. Almost caused accident to others.
The contact owns a 2020 GMC Sierra 2500. The contact received notification of NHTSA Campaign Number: 24V797000 (Power Train); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. Th…
Read full complaint
The contact owns a 2020 GMC Sierra 2500. The contact received notification of NHTSA Campaign Number: 24V797000 (Power Train); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
The contact owns a 2020 GMC Sierra 2500. The contact stated that the vehicle was under NHTSA Campaign Number: 24V797000 (Power Train) and the vehicle was repaired. The contact stated that after the recall repair, the transmission started shifting hard. The vehicle was taken to the dealer, and the contact was informed that the tr…
Read full complaint
The contact owns a 2020 GMC Sierra 2500. The contact stated that the vehicle was under NHTSA Campaign Number: 24V797000 (Power Train) and the vehicle was repaired. The contact stated that after the recall repair, the transmission started shifting hard. The vehicle was taken to the dealer, and the contact was informed that the transmission module would reprogram and adjust independently. The contact stated that a week later, while driving approximately 45 MPH, the vehicle started to run rough, and the message engine power reduced was displayed. The transmission fault, parking brake system alert, service parking brake, and the check engine warning light illuminated. The vehicle was towed to the dealer, who diagnosed the vehicle and determined that the fuel injector was open, causing high resistance in the connector for cylinder #4. The transmission could not be diagnosed until the injector was repaired. The manufacturer was informed of the failure and opened a case. The failure mileage was 125,000.
I have a notice of a recall for the transmission control module and I took it to a GMC dealership and they are refusing to fix it. The transmission will not shift so I am unable to drive it
Official recalls
926V083000 · Power Train:automatic Transmission:control Module:software; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
Feb 12, 2026
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence & remedy
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
Additional source detail variants (2)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
Power Train:automatic Transmission:control Module:software
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
24V797000 · Power Train:automatic Transmission:control Module:software; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
Oct 24, 2024
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence & remedy
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
Additional source detail variants (2)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
Power Train:automatic Transmission:control Module:software
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
24V060000 · Latches/locks/linkages:tailgate:latch
Feb 1, 2024
General Motors, LLC (GM) is recalling certain 2020-2024 Chevrolet Silverado 2500, 3500, GMC Sierra 2500 and 3500 vehicles equipped with power-unlatching tailgates. The tailgate's electronic gate-release switch may short circuit due to water intrusion, which can result in the tailgate inadvertently unlatching while the vehicle is in park.
Consequence & remedy
Consequence: An unlatched tailgate may open while driving and result in a loss of unsecured cargo, creating a road hazard and increasing the risk of a crash.
Remedy: Owners are advised to check that the tailgate is closed and latched before driving. Dealers will replace the exterior touchpad switch assemblies, free of charge. Owner notification letters were mailed May 17, 2024. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is N232426400.
21V578000 · Tires:temporary/emergency Spare Tire
Jul 29, 2021
General Motors, LLC. (GM) is recalling certain 2020-2021 Chevrolet Silverado 2500 and GMC Sierra 2500 vehicles equipped with a 17" spare tire (RPO ZHQ or ZXT) and either the 20" accessory road tire (RPO REM) or the 18" accessory road tire (RPO Q2V). Operating the spare tire with other 20" or 18" tires can prevent the Anti-Lock Braking System (ABS) from engaging.
Consequence & remedy
Consequence: An ABS system that cannot control the rear wheels independently increases the risk of a crash.
Remedy: Dealers will provide the appropriate spare tire and apply a new spare tire information label, free of charge. Owner notification letters were mailed on October 18, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; GMC customer service at 1-800-462-8782. GM's number for this recall is N212329780.
20V792000 · Seat Belts; Seat Belts:critical Fasteners
Dec 17, 2020
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence & remedy
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
Additional source detail variants (2)
Seat Belts:critical Fasteners
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
Seat Belts
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
20V446000 · Air Bags:side/window:curtain:inflator
Jul 30, 2020
General Motors, LLC. (GM) is recalling certain 2020 Buick Enclave, Cadillac XT5 and XT6, Chevrolet Blazer, Silverado 1500, 2500 and 3500 and Traverse and GMC Acadia and Sierra 1500, 2500 and 3500 vehicles. The diffuser component of the Roof-Rail Air Bag (RRAB) inflator may not have been properly crimped to the inflator and could separate from the inflator during air bag deployment.
Consequence & remedy
Consequence: If the diffuser separates from the inflator during deployment, RRAB performance may be degraded, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will replace the suspect RRAB modules, free of charge. The recall began September 3, 2020. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-333-4223, or Buick customer service at 1-800-521-7300. GM's number for this recall is N202305380.
20V324000 · Latches/locks/linkages:hood:latch; Structure:body:hood
Jun 4, 2020
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles previously recalled under 20V-142. Some of the vehicles in 20V-324 were not part of Recall 20V-142 but received defect parts during another service (typically during collision repair). The hood-latch striker wires on replacement hoods installed for Safety Recall 20V-142 may not have been heat-treated properly, possibly causing them to fracture.
Consequence & remedy
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. For hoods sold over the counter, dealers will contact customers with instructions for hood replacement. The recall began July 7, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N202306490.
Additional source detail variants (2)
Latches/locks/linkages:hood:latch
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles previously recalled under 20V-142. Some of the vehicles in 20V-324 were not part of Recall 20V-142 but received defect parts during another service (typically during collision repair). The hood-latch striker wires on replacement hoods installed for Safety Recall 20V-142 may not have been heat-treated properly, possibly causing them to fracture.
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. For hoods sold over the counter, dealers will contact customers with instructions for hood replacement. The recall began July 7, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N202306490.
Structure:body:hood
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles previously recalled under 20V-142. Some of the vehicles in 20V-324 were not part of Recall 20V-142 but received defect parts during another service (typically during collision repair). The hood-latch striker wires on replacement hoods installed for Safety Recall 20V-142 may not have been heat-treated properly, possibly causing them to fracture.
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. For hoods sold over the counter, dealers will contact customers with instructions for hood replacement. The recall began July 7, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N202306490.
20V142000 · Latches/locks/linkages:hood:latch
Mar 12, 2020
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The hood-latch striker wires may not have been heat-treated properly, possibly causing them to fracture.
Consequence & remedy
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. The recall began April 13, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N192284960.
19V814000 · Seat Belts:pretensioner
Nov 14, 2019
General Motors LLC (GM) is recalling certain 2019-2020 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2020 Silverado 2500, Silverado 3500, Sierra 2500, and Sierra 3500 vehicles equipped with carpet floor covering. When the front seat belt pretensioners deploy, hot gas may vent through an opening in the pretensioner bracket, possibly igniting the carpet.
Consequence & remedy
Consequence: A vehicle fire could result if materials ignite inside the vehicle.
Remedy: GM will notify owners, and dealers will close off the opening in the pretensioner bracket, free of charge. The recall began December 13, 2019. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N192270600.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE21010 · Air Bag Malfunction
Opened Apr 9, 2021 · Closed Aug 24, 2023
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:srs Malfunction Warning Lamp/light
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Additional source detail variants (4)
Air Bags:frontal:driver Side:inflator Module
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags:frontal
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags:srs Malfunction Warning Lamp/light
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.