Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 4 of 6 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
Steering. Review the 3 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Electronic Stability Control (esc). Review the 2 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Service Brakes. Review the 2 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
6L80 transmission has failed @ 109,000 miles. At a stop light, in drive, vehicle would not move in drive or reverse. After switching back and forth transmission finally started to work and was able to limp to a dealership. Did not realize how big this issue is with this transmission until mine failed prematurely. I thank God tha…
Read full complaint
6L80 transmission has failed @ 109,000 miles. At a stop light, in drive, vehicle would not move in drive or reverse. After switching back and forth transmission finally started to work and was able to limp to a dealership. Did not realize how big this issue is with this transmission until mine failed prematurely. I thank God that mine happened at a stop light and not when trying to accelerate at a say a stop sign where I need to cross multiple lanes of traffic. I would have been a sitting duck in the middle of oncoming traffic.
General Motors, LLC (GM) is recalling certain 2003-2023 Chevrolet Express Cutaway and GMC Savana Cutaway incomplete vehicles equipped with wiring for an optional rear heating, ventilation, and air-conditioning (HVAC) system. When the HVAC blower motor circuit is left unused with exposed connectors and wiring, the circuit can corrode and overheat.
Consequence & remedy
Consequence: An overheated electrical circuit increases the risk of a fire.
Remedy: Dealers will properly seal the rear HVAC blower motor circuits at the left side B-pillar, free of charge. Owner notification letters were mailed May 2, 2023. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GMC's number for this recall is N222386050.
General Motors LLC (GM) is recalling certain 2016-2019 Chevrolet Express and GMC Savana vehicles. One or both of the rear-quarter windows may be tempered glass instead of laminated glass. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 226, "Ejection Mitigation."
Consequence & remedy
Consequence: Tempered glass increases the risk of injury in the event of a side impact or rollover crash.
Remedy: GM will notify owners, and dealers will replace the tempered glass windows with laminated glass windows, as necessary, free of charge. The recall began July 5, 2019. Owners may contact GM customer service at 1-586-596-1733. GM's number for this recall is N192218960.
General Motors LLC (GM) is recalling certain 2016-2018 Chevrolet Express and GMC Sierra vehicles equipped with a single, manual, rear climate control module (CCM). If the temperature is set to maximum heat or the mode knob is set to maximum floor vent and an electrical short occurs, components within the CCM may overheat.
Consequence & remedy
Consequence: If the CCM overheats, there is an increased risk of a fire in the vehicle's headliner.
Remedy: GM will notify owners, and dealers will remove the electrical insulation from a wiring connector within the CCM to remove the fire risk, free of charge. The recall began November 6, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is 18299.
General Motors LLC (GM) is recalling certain 2014-2017 Chevrolet Express and GMC Savana vehicles equipped with power windows. Liquid may leak into the driver's power window switch and cause corrosion, resulting in high electrical resistance.
Consequence & remedy
Consequence: High electrical resistance can increase the risk of a fire.
Remedy: GM will notify owners, and dealers will replace the driver side window switch, free of charge. The recall began August 10, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is 18155.
General Motors LLC (GM) is recalling certain 2009-2014 Chevrolet Silverado HD and GMC Sierra HD, 2009 GMC Topkick 5000, 6000, 7000 and 8000 Series and Isuzu F Series, and 2009-2018 Chevrolet Express, and GMC Savana vehicles, equipped with certain Plastic-Handle Fire Extinguishers or Push Button 'Pindicator' Fire Extinguishers. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.
Remedy: GM will notify owners, instructing them to contact Kidde to get a replacement fire extinguisher, free of charge. The recall began June 11, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020, GMC customer service at 1-800-462-8782, and Isuzu customer service at 1-866-441-9638. GM's number for this recall is 18146.
General Motors LLC (GM) is recalling certain model year 2016-2017 Chevrolet Express manufactured September 25, 2015, to August 22, 2016, and 2016 GMC Savana cargo and cutaway vans manufactured January 28, 2016, to May 18, 2016. The affected vehicles were manufactured without an inside rearview mirror and with a right-hand convex exterior review mirror. These vehicles are required to have either an inside rearview mirror or both left and right-hand flat exterior rearview mirrors. Thus, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rearview Mirrors."
Consequence & remedy
Consequence: If the driver does not have a clear unobstructed view to the back of the vehicle, it can increase the risk of a crash.
Remedy: GM will notify owners, and dealers will instal a right-hand flat rearview mirror, free of charge. The recall began on November 8, 2016. Owners may contact Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16036.
General Motors LLC (GM) is recalling certain model year 2014-2016 Chevrolet Express and GMC Savana incomplete vehicles equipped with a 159 inch wheel base manufactured August 2, 2013, to January 30, 2016. The affected vehicles were shipped to final stage manufacturers without a tire pressure monitoring system (TPMS). As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 138, "Tire Pressure Monitoring Systems."
Consequence & remedy
Consequence: Without a TPMS, the driver would not be alerted if one or more tires became under inflated. Driving with under inflated tires increases the risk of a crash.
Remedy: GM will notify owners, and dealers will install the hardware and software necessary to equip the vehicles with a TPMS, free of charge. The recall began on May 25, 2016. Owners may contact Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 15819.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
PE23016 · 6L90 Transmission Failure
Opened Sep 27, 2023 · Closed Jan 10, 2025
Status: closed (inferred from source dates) · Power Train; Power Train:automatic Transmission; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
The Office of Defects Investigation (ODI) opened this Preliminary Evaluation (PE) after receiving one Vehicle Owner Questionnaire (VOQ) complaint related to four school buses built on General Motors (GM) van chassis. The VOQ alleged transmission failure resulting in a loss of all forward gear. In ODI's pre-investigative discussions with GM, ODI learned that valve body separator plates had been machined out of tolerance during production periods between October 2016 to April 2017 and February 2021 to April 2021. This out of tolerance machining may create excessive wear to the valve body check balls, possibly resulting in an inability to engage drive or reverse. The potential loss of drivability only begins when shifting from a park or neutral transmission selection and does not occur during a functional drive cycle. The average failure mileage of vehicles which experienced this condition is within warranty and related claims or complaints did not include any accidents, injuries, or fatalities. After discussions with GM, Technical Service Bulletin (TSB) 23-NA-142 (NHTSA ID number 10243753) was released in September 2023. This technical service bulletin provides a procedure for technicians to replace the forward check ball and separator plate if found to be the cause of a customer's concern. During the course of the investigation, GM also released a Customer Satisfaction Program (CSP) N232428780 (NHTSA ID 10253316) in February 2024, to notify school bus and ambulance fleets of the concern and to proactively mitigate the risk in these essential-operation vehicles. Recently, ODI contacted multiple school bus fleets, verifying that there have not been any stranded buses mid-route from this condition. Additionally, ODI has not received any additional VOQ complaints since the opening of this investigation. Based on the available information, including GM's TSB and CSP, this PE is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI report cited in the Closing Resume ODI Report Identification Numbers document, go to NHTSA.gov.
Additional source detail variants (3)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
The Office of Defects Investigation (ODI) opened this Preliminary Evaluation (PE) after receiving one Vehicle Owner Questionnaire (VOQ) complaint related to four school buses built on General Motors (GM) van chassis. The VOQ alleged transmission failure resulting in a loss of all forward gear. In ODI's pre-investigative discussions with GM, ODI learned that valve body separator plates had been machined out of tolerance during production periods between October 2016 to April 2017 and February 2021 to April 2021. This out of tolerance machining may create excessive wear to the valve body check balls, possibly resulting in an inability to engage drive or reverse. The potential loss of drivability only begins when shifting from a park or neutral transmission selection and does not occur during a functional drive cycle. The average failure mileage of vehicles which experienced this condition is within warranty and related claims or complaints did not include any accidents, injuries, or fatalities. After discussions with GM, Technical Service Bulletin (TSB) 23-NA-142 (NHTSA ID number 10243753) was released in September 2023. This technical service bulletin provides a procedure for technicians to replace the forward check ball and separator plate if found to be the cause of a customer's concern. During the course of the investigation, GM also released a Customer Satisfaction Program (CSP) N232428780 (NHTSA ID 10253316) in February 2024, to notify school bus and ambulance fleets of the concern and to proactively mitigate the risk in these essential-operation vehicles. Recently, ODI contacted multiple school bus fleets, verifying that there have not been any stranded buses mid-route from this condition. Additionally, ODI has not received any additional VOQ complaints since the opening of this investigation. Based on the available information, including GM's TSB and CSP, this PE is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI report cited in the Closing Resume ODI Report Identification Numbers document, go to NHTSA.gov.
Power Train:automatic Transmission
The Office of Defects Investigation (ODI) opened this Preliminary Evaluation (PE) after receiving one Vehicle Owner Questionnaire (VOQ) complaint related to four school buses built on General Motors (GM) van chassis. The VOQ alleged transmission failure resulting in a loss of all forward gear. In ODI's pre-investigative discussions with GM, ODI learned that valve body separator plates had been machined out of tolerance during production periods between October 2016 to April 2017 and February 2021 to April 2021. This out of tolerance machining may create excessive wear to the valve body check balls, possibly resulting in an inability to engage drive or reverse. The potential loss of drivability only begins when shifting from a park or neutral transmission selection and does not occur during a functional drive cycle. The average failure mileage of vehicles which experienced this condition is within warranty and related claims or complaints did not include any accidents, injuries, or fatalities. After discussions with GM, Technical Service Bulletin (TSB) 23-NA-142 (NHTSA ID number 10243753) was released in September 2023. This technical service bulletin provides a procedure for technicians to replace the forward check ball and separator plate if found to be the cause of a customer's concern. During the course of the investigation, GM also released a Customer Satisfaction Program (CSP) N232428780 (NHTSA ID 10253316) in February 2024, to notify school bus and ambulance fleets of the concern and to proactively mitigate the risk in these essential-operation vehicles. Recently, ODI contacted multiple school bus fleets, verifying that there have not been any stranded buses mid-route from this condition. Additionally, ODI has not received any additional VOQ complaints since the opening of this investigation. Based on the available information, including GM's TSB and CSP, this PE is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI report cited in the Closing Resume ODI Report Identification Numbers document, go to NHTSA.gov.
Power Train
The Office of Defects Investigation (ODI) opened this Preliminary Evaluation (PE) after receiving one Vehicle Owner Questionnaire (VOQ) complaint related to four school buses built on General Motors (GM) van chassis. The VOQ alleged transmission failure resulting in a loss of all forward gear. In ODI's pre-investigative discussions with GM, ODI learned that valve body separator plates had been machined out of tolerance during production periods between October 2016 to April 2017 and February 2021 to April 2021. This out of tolerance machining may create excessive wear to the valve body check balls, possibly resulting in an inability to engage drive or reverse. The potential loss of drivability only begins when shifting from a park or neutral transmission selection and does not occur during a functional drive cycle. The average failure mileage of vehicles which experienced this condition is within warranty and related claims or complaints did not include any accidents, injuries, or fatalities. After discussions with GM, Technical Service Bulletin (TSB) 23-NA-142 (NHTSA ID number 10243753) was released in September 2023. This technical service bulletin provides a procedure for technicians to replace the forward check ball and separator plate if found to be the cause of a customer's concern. During the course of the investigation, GM also released a Customer Satisfaction Program (CSP) N232428780 (NHTSA ID 10253316) in February 2024, to notify school bus and ambulance fleets of the concern and to proactively mitigate the risk in these essential-operation vehicles. Recently, ODI contacted multiple school bus fleets, verifying that there have not been any stranded buses mid-route from this condition. Additionally, ODI has not received any additional VOQ complaints since the opening of this investigation. Based on the available information, including GM's TSB and CSP, this PE is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI report cited in the Closing Resume ODI Report Identification Numbers document, go to NHTSA.gov.
2016 GMC Savana Problems, Complaints & Recalls | Skip That Year
Illustration