IllustrationI WAS BACKING OUT OF THE DRIVEWAY ON 12/4/07 IN ,Y 2002 FORD TAURUS SES WHEN I HEARD A LOUD BANG UNDER THE CAR. THE DRIVER SIDE FRONT TIRE BLEW OUT. WHEN I REMOVED IT, I SAW THAT THE COIL SPRING HAD BROKEN AND CUT INTO THE TIRE. *TR
2002 Ford Taurus
Owner reports · Recalls · Investigations
More warning signs than most Taurus years
Owner complaints for the 2002 Ford Taurus are substantially higher than the model-year median of 318.
About this comparison →How this year compares
Owner complaints by model year
Compare all Taurus years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
600–25K
16525–50K
29950–75K
31175–100K
321100–150K
73150K+
1,229 reports with mileage · 197 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Suspension. Review the 962 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Visibility. Review the 98 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Vehicle Speed Control. Review the 76 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
75 crash reports11 fire reports40 injury reports
Tires complaints
38 reportsDRIVER FRONT SHOCK AND STRUT BROKE AND BLEW THE TIRE. LUCKILY I WAS IN DRIVEWAY JUST LEAVING FOR WORK HAD TO CALL TOW TRUCK TO BRING TO GARAGE FOR REPAIR BEING IT WAS A 2002 VEHICLE THE SCHROAD WAS SUPPOSE TO BE PUT ON THE 2002 VEHICLE AND NEWER, BUT THIS DID NOT HAVE ANYTHING ON IT. SO TIRE BLEW, BUT LUCKILY I WAS NOT GOING …
Read full complaint
DRIVER FRONT SHOCK AND STRUT BROKE AND BLEW THE TIRE. LUCKILY I WAS IN DRIVEWAY JUST LEAVING FOR WORK HAD TO CALL TOW TRUCK TO BRING TO GARAGE FOR REPAIR BEING IT WAS A 2002 VEHICLE THE SCHROAD WAS SUPPOSE TO BE PUT ON THE 2002 VEHICLE AND NEWER, BUT THIS DID NOT HAVE ANYTHING ON IT. SO TIRE BLEW, BUT LUCKILY I WAS NOT GOING 60 MILES A HOUR DOWN THE HWY. WE STILL HAVE THE OLD PARTS FOR PROOF OF DAMAGE. *TR
2002 FORD TAURUS WITH BROKEN REAR COIL SPRINGS AND OTHER PROBLEMS. CONSUMER STATES THE COILS SPRINGS BROKE, TIRES ARE WOBBLING, AND THE BELT TENSIONER LOST POWER STEERING. *KB
2002 FORD TAURUS SE FRONT DRIVERS SIDE SPRING SNAPPED. THIS WAS RECALLED IN 1999-2001 FORD TAURUS'S WITH THE SAME PROBLEM BUT NOT THE 2002. I HAVE SEEN MANY COMPLAINTS ABOUT THIS WHEN I GOOGLED THE PROBLEM. PLEASE HELP!! *I COULDN'T FIND FORD ON THE MANUFACTURE SECTION, SO I SELECTED CHRYSLER TO PROCEED. *JB
I PURCHASE 4 KUMHO 215/60/16 TIRES IN MAY OF 2004 AND HAVE PUT LEAST THAN 20,000 MILES ON THEM WHEN I WENT OUT GET MY CAR INSPECTED THEY SAID THAT THE TIRES WERE "JUNK" EXTREMELY DANGEROUS TO BE ON THE ROAD BECAUSE THEY WERE CRACKED AND ONE BELT WAS BROKEN ON THE RIGHT FRONT TIRE- I FEEL THESE TIRES SHOULD BE ADDED TO THE RECALL…
Read full complaint
I PURCHASE 4 KUMHO 215/60/16 TIRES IN MAY OF 2004 AND HAVE PUT LEAST THAN 20,000 MILES ON THEM WHEN I WENT OUT GET MY CAR INSPECTED THEY SAID THAT THE TIRES WERE "JUNK" EXTREMELY DANGEROUS TO BE ON THE ROAD BECAUSE THEY WERE CRACKED AND ONE BELT WAS BROKEN ON THE RIGHT FRONT TIRE- I FEEL THESE TIRES SHOULD BE ADDED TO THE RECALL LIST AND ANYONE WHO PURCHASED THEM SHOULD BE REIMBURSED FOR THERE EXPENSES. *TR
MY WIFE STARTED TO BACK OUT OF THE DRIVEWAY IN THE 2002 FORD TAURUS AND HEARD A BANG FOLLOWED BY HISSING. SHE SAW THE FLAT TIRE AND CALLED HER BROTHER TO COME HELP SINCE I WAS OUT OF TOWN ,AND AFTER HE JACKED THE CAR UP THEY SAW THE SPRING HAD BROKEN AND PUNCTURED THE DRIVER'S SIDE FRONT TIRE. THE SPRING WAS STICKING FAR ENOUG…
Read full complaint
MY WIFE STARTED TO BACK OUT OF THE DRIVEWAY IN THE 2002 FORD TAURUS AND HEARD A BANG FOLLOWED BY HISSING. SHE SAW THE FLAT TIRE AND CALLED HER BROTHER TO COME HELP SINCE I WAS OUT OF TOWN ,AND AFTER HE JACKED THE CAR UP THEY SAW THE SPRING HAD BROKEN AND PUNCTURED THE DRIVER'S SIDE FRONT TIRE. THE SPRING WAS STICKING FAR ENOUGH OUT THAT WE COULD NOT PUT A NEW TIRE ON, SO WE PUT THE DOUGHNUT SPARE TIRE ON AND CALLED A TOW TRUCK. THE CAR WAS TOWED TO A FORD DEALER ,WHERE THEY REPLACED THE TWO FRONT SPRINGS, TWO FRONT STABILIZER LINKS, AND A NEW TIRE. TOTAL COST WAS $843.83. *AK
EVENTS LEADING UP TO THE FAILURE WAS A APPROXIMATELY 100 MILE ROUND TRIP ON THE INTERSTATE TRAVELING 65 MPH, THE EVENING PRIOR TO THE INCIDENT. THE FAILURE CONSISTED OF THE DRIVER'S SIDE COIL SPRING BREAKING AND SEVERLY DAMAGING THE FRONT DIVER'S SIDE TIRE AND SWAY BAR. THE INCIDENT OCCURRED WHILE THE VEHICLE WAS PARKED IN A PA…
Read full complaint
EVENTS LEADING UP TO THE FAILURE WAS A APPROXIMATELY 100 MILE ROUND TRIP ON THE INTERSTATE TRAVELING 65 MPH, THE EVENING PRIOR TO THE INCIDENT. THE FAILURE CONSISTED OF THE DRIVER'S SIDE COIL SPRING BREAKING AND SEVERLY DAMAGING THE FRONT DIVER'S SIDE TIRE AND SWAY BAR. THE INCIDENT OCCURRED WHILE THE VEHICLE WAS PARKED IN A PARKING LOT AND NOT BEING DRIVEN. THE MAKE AND MODEL OF THE CAR WAS A 2002 FORD TAURUS SE. THE DEALERSHIP HAD TO REPLACE BOTH FRONT COIL SPRINGS, REPLACE THE DRIVER SIDE SWAY BAR, REPLACE THE TIRE, AND REALIGN THE SUSPENSION.*AK
MY 2002 FORD TAURUS SE WAS PARKED WHEN I WENT TO PULL OUT OF THE SPACE, THE CAR MADE LOUD SNAPPING SOUNDS AND WAS JOLTED, THEN WOULD NOT MOVE PROPERLY. I GOT OUT TO CHECK AND THE DRIVER' S SIDE FRONT TIRE WAS FLAT. PUT ON THE SPARE TIRE, AND FOUND A LARGE GASH CUT INTO THE INNER WALL OF THE FLAT TIRE. FOUND OUT THAT A BROKEN CO…
Read full complaint
MY 2002 FORD TAURUS SE WAS PARKED WHEN I WENT TO PULL OUT OF THE SPACE, THE CAR MADE LOUD SNAPPING SOUNDS AND WAS JOLTED, THEN WOULD NOT MOVE PROPERLY. I GOT OUT TO CHECK AND THE DRIVER' S SIDE FRONT TIRE WAS FLAT. PUT ON THE SPARE TIRE, AND FOUND A LARGE GASH CUT INTO THE INNER WALL OF THE FLAT TIRE. FOUND OUT THAT A BROKEN COIL SPRING DESTROYED THE TIRE. CONTACTED TWO FORD DEALERS AS WELL AS THEIR NATIONAL CUSTOMER SERVICE CENTER, AND WAS TOLD THAT THERE WAS NO RECALL ON THE 2002 TAURUS, AND THEY WOULD NOT DO ANYTHING TO COMPENSATE ME FOR THE REPAIRS, ALTHOUGH I STATED SEVERAL TIMES THAT THIS WAS A COMMON AND TOO WELL-KNOWN PROBLEM WITH THE TAURUS. I HAVE YET TO PAY THE REPAIR BILL, BUT KNOW IT WILL BE AROUND $400.00 FOR THE REPLACEMENT OF COIL SPRINGS AND TIRE. I AM SAVING MY RECEIPTS AND THE DEFECTIVE COIL IN THE HOPE THAT A RECALL WILL BE ORDERED. THANK GOODNESS THIS DID NOT HAPPEN ON THE HIGHWAY. *AK
I BACKED OUT OF A PARKING SPACE AND HEARD A GRINDING SOUND. I CHECKED THE FRONT END BUT COULD NOT SEE ANY PROBLEMS. I DROVE FORWARD APPROXIMATELY 10 FEET AND HEARD A BANG AS THE RIGHT FRONT PASSENGER SIDE TIRE BLEW OUT. WHEN I CHANGED THE TIRE I FOUND THE RIGHT FRONT COIL SPRING IMPALED IN THE TIRE'S SIDEWALL. THE SPRING …
Read full complaint
I BACKED OUT OF A PARKING SPACE AND HEARD A GRINDING SOUND. I CHECKED THE FRONT END BUT COULD NOT SEE ANY PROBLEMS. I DROVE FORWARD APPROXIMATELY 10 FEET AND HEARD A BANG AS THE RIGHT FRONT PASSENGER SIDE TIRE BLEW OUT. WHEN I CHANGED THE TIRE I FOUND THE RIGHT FRONT COIL SPRING IMPALED IN THE TIRE'S SIDEWALL. THE SPRING BROKE AND THE SHARP END ROTATED INTO THE TIRE. FIFTEEN MINUTES EARLIER, I HAD BEEN DRIVING AT 70 MPH ON I-80 BEFORE EXITING AT MISHAWAKA. I HAD THE CAR TOWED TO A LOCAL GARAGE , AND THE SPRING/STRUT ASSEMBLY WAS VREPLACED. THE TOW TRUCK DRIVER COMMENTED HE HAD SEEN APPROXIMATELY 20 OF THESE INCIDENTS OVER THE PAST 12 MONTHS.*AK
FRONT END HAS HAD VIBRATION SINCE I BOUGHT THE CAR. HAVE HAD CONTINENTAL ORIGINAL TIRES REPLACED UNDER WARRANTY 3 TIMES BECAUSE DEALERSHIP SAID VIBRATION WAS DUE TO TIRE FAILURE "EXCESSIVE RUNOUT". VIBRATION IS RETURNING AGAIN.
Official recalls
304V106000 · Exterior Lighting:brake Lights:switch
Mar 2, 2004
CERTAIN PASSENGER VEHICLES ARE BEING RECALLED TO CORRECT A PROBLEM WITH A MALFUNCTIONING STOP LAMP SWITCH AND/OR ASSOCIATED WIRING. THIS MALFUNCTIONING COULD RENDER THE STOP LAMPS INOPERABLE OR CAUSE THEM TO STAY ON ALL THE TIME. THIS COULD CAUSE CONFUSION TO A FOLLOWING DRIVER, WHICH COULD LEAD TO A CRASH.
Consequence & remedy
Consequence: IN ADDITION, IF THE SWITCH AND/OR ASSOCIATED WIRING FAIL IN THE OPEN POSITION, THE BRAKE LIGHTS WILL NOT ACTUATE AND THE DRIVER WILL NOT BE ABLE TO SHIFT THE VEHICLE OUT OF "PARK" IF THEY FAIL IN THE CLOSED POSITION, THE BRAKE LIGHTS WILL REMAIN ON, WHICH WILL NOT ALLOW THE SPEED CONTROL TO BE ACTIVATED. THIS COULD ALSO CAUSE THE BATTERY TO DISCHARGE.
Remedy: DEALERS WILL REMOVE THE STOP LAMP SWITCH AND ASSOCIATED WIRING ASSEMBLY AND INSTALL A NEWLY DESIGNED STOP LAMP SWITCH AND WIRE ASSEMBLY. OWNER NOTIFICATION IS EXPECTED TO BEGIN ON APRIL 5, 2004. OWNERS SHOULD CONTACT FORD AT 1-800-392-3673.
03V087000 · Visibility:windshield
Mar 10, 2003
CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, "WINDSHIELD MOUNTING." THE WINDSHIELDS MAY POTENTIALLY EXHIBIT INCREASED WIND NOISE, WATER LEAKAGE, AND SQUEAKS AND RATTLES.
Consequence & remedy
Consequence: POTENTIAL LOSS OF WINDSHIELD RETENTION MAY ALSO REDUCE OCCUPANT PROTECTION IN THE EVENT OF A CRASH.
Remedy: DEALERS WILL REPLACE THESE WINDSHIELDS. OWNER NOTIFICATION BEGAN ON MARCH 31, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD/MERCURY AT 1-800-392-3673.
02V266000 · Service Brakes, Hydraulic:pedals And Linkages
Oct 2, 2002
CERTAIN PASSENGER VEHICLES EQUIPPED WITH ADJUSTABLE PADELS ARE BEING RECALLED IN ORDER TO ADJUST THE BRAKE AND ACCELERATOR PEDALS TO A MINIMUM OF 50 MM OF LATERAL SEPARATION. SIMULTANEOUS APPLICATION OF BOTH THE BRAKE AND ACCELERATOR PEDALS COULD RESULT IN AN INCREASE IN ENGINE RPM.
Consequence & remedy
Consequence: THIS COULD RESULT IN A CUSTOMER EXPERIENCING AN "UNINTENDED VEHICLE SPEED INCREASE" OR A PERCEIVED "UNABLE TO STOP" CONDITION.
Remedy: OWNERS WILL BE INSTRUCTED AS TO THE PROPER WAY TO SET THE POSITION OF THE PEDALS AND TO TAKE THEIR VEHICLES TO A DEALER TO HAVE THE SPACING BETWEEN THE BRAKE AND ACCELERATOR PEDALS MEASURED. IF THE SPACING IS FOUND TO BE LESS THAN 50 MM, THE DEALER WILL ADJUST THE PEDALS TO INCREASE THE DISTANCE BETWEEN THEM TO GREATER THAN 50 MM. OWNER NOTIFICATION BEGAN OCTOBER 28, 2002. OWNERS WHO DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4PE12033 · Speed Control Cable Damage
Opened Oct 24, 2012 · Closed Jun 26, 2013
Status: closed (inferred from source dates) · Vehicle Speed Control; Vehicle Speed Control:cables; Vehicle Speed Control:cruise Control
On June 21, 2013, Ford initiated Customer Satisfaction Program 13B04 to address a concern with Speed Control Cable damage in certain model year (MY) 2000 through 2003 Taurus and Sable vehicles equipped with 3.0L 4V Duratec engines and built at the Chicago assembly plant.In the dealer letter for the program, Ford indicates that the Speed Control Cables on affected vehicles may be susceptible to damage or becoming partially disconnected during under hood vehicle maintenance (e.g., replacing a battery or changing the air filter) and that a damaged Speed Control Cable could interfere with the throttle's full return to idle when the accelerator pedal is released.Ford's program instructs dealers to inspect the Speed Control Cables and replace any with any portion of either collar retention tab missing.Dealers will install a Collar Reinforcement Clip at the Speed Control Cable collar in all vehicles. Figure 1 shows the location of the Speed Control Cable in the engine compartment and the proximity of the battery and air filter.The failure mode of the cable assembly is associated with the plastic collar used to secure the cable to a bracket near the throttle body (Figure 2).Damage to one or both retention tabs used to secure the cable ferrule within the collar may allow the ferrule to become disconnected from the collar when the throttle is opened during accelerator pedal application.Additional examples of Speed Control Cables with damaged collar retention tabs and partial ferrule displacement are shown in Figures 3 through 5.If the displacement pulls the ferrule completely out of the collar, the ferrule end may contact the face of the collar when the accelerator pedal is released and the throttle is returning to idle (Figure 6).This results in a throttle stuck at approximately 26-29% open.Testing conducted at NHTSA's Vehicle Research and Test Center found that brake booster vacuum may become depleted, resulting in reduced brake effectiveness, if the brake is applied repeatedly when the throttle is stuck at this position.Drivers who experienced this condition have reported being surprised that the engine speed did not drop as expected and in some cases misjudged the degree of braking required to slow the vehicle.Some drivers reported difficulty in braking the vehicle and responded by shifting to neutral or turning the engine off.One minor crash occurred when the vehicle contacted a roadside fence post after the driver responded to the stuck throttle by shifting the car to neutral, turning the engine off and coasting to the side of a roadway with no shoulder, resulting in approximately $400 damage to the vehicle.There were four crashes reported which were attributed to increased stopping distance caused by the increased engine power and/or reduced brake effectiveness, including two of the complaints to ODI.In one crash reported to ODI (VOQ 10516101), the subject vehicle allegedly hit the back end of a truck at approximately 40 mph causing about $2000 damage.In the other crash complaint to ODI (VOQ 10501834), the subject vehicle side-swiped a vehicle as the driver was unable to stop in time and attempted to maneuver around a line of vehicles stopped at a traffic light.When the tow truck driver subsequently started the incident vehicle, the engine was still racing and it was verified that the Speed Control Cable ferrule was stuck on the collar.After further investigation, ODI does not consider the crashes reported in VOQs 10456249 and 10159399 to be related to the Speed Control Cable problem.
Additional source detail variants (3)
Vehicle Speed Control:cables
On June 21, 2013, Ford initiated Customer Satisfaction Program 13B04 to address a concern with Speed Control Cable damage in certain model year (MY) 2000 through 2003 Taurus and Sable vehicles equipped with 3.0L 4V Duratec engines and built at the Chicago assembly plant.In the dealer letter for the program, Ford indicates that the Speed Control Cables on affected vehicles may be susceptible to damage or becoming partially disconnected during under hood vehicle maintenance (e.g., replacing a battery or changing the air filter) and that a damaged Speed Control Cable could interfere with the throttle's full return to idle when the accelerator pedal is released.Ford's program instructs dealers to inspect the Speed Control Cables and replace any with any portion of either collar retention tab missing.Dealers will install a Collar Reinforcement Clip at the Speed Control Cable collar in all vehicles. Figure 1 shows the location of the Speed Control Cable in the engine compartment and the proximity of the battery and air filter.The failure mode of the cable assembly is associated with the plastic collar used to secure the cable to a bracket near the throttle body (Figure 2).Damage to one or both retention tabs used to secure the cable ferrule within the collar may allow the ferrule to become disconnected from the collar when the throttle is opened during accelerator pedal application.Additional examples of Speed Control Cables with damaged collar retention tabs and partial ferrule displacement are shown in Figures 3 through 5.If the displacement pulls the ferrule completely out of the collar, the ferrule end may contact the face of the collar when the accelerator pedal is released and the throttle is returning to idle (Figure 6).This results in a throttle stuck at approximately 26-29% open.Testing conducted at NHTSA's Vehicle Research and Test Center found that brake booster vacuum may become depleted, resulting in reduced brake effectiveness, if the brake is applied repeatedly when the throttle is stuck at this position.Drivers who experienced this condition have reported being surprised that the engine speed did not drop as expected and in some cases misjudged the degree of braking required to slow the vehicle.Some drivers reported difficulty in braking the vehicle and responded by shifting to neutral or turning the engine off.One minor crash occurred when the vehicle contacted a roadside fence post after the driver responded to the stuck throttle by shifting the car to neutral, turning the engine off and coasting to the side of a roadway with no shoulder, resulting in approximately $400 damage to the vehicle.There were four crashes reported which were attributed to increased stopping distance caused by the increased engine power and/or reduced brake effectiveness, including two of the complaints to ODI.In one crash reported to ODI (VOQ 10516101), the subject vehicle allegedly hit the back end of a truck at approximately 40 mph causing about $2000 damage.In the other crash complaint to ODI (VOQ 10501834), the subject vehicle side-swiped a vehicle as the driver was unable to stop in time and attempted to maneuver around a line of vehicles stopped at a traffic light.When the tow truck driver subsequently started the incident vehicle, the engine was still racing and it was verified that the Speed Control Cable ferrule was stuck on the collar.After further investigation, ODI does not consider the crashes reported in VOQs 10456249 and 10159399 to be related to the Speed Control Cable problem.
Vehicle Speed Control:cruise Control
On June 21, 2013, Ford initiated Customer Satisfaction Program 13B04 to address a concern with Speed Control Cable damage in certain model year (MY) 2000 through 2003 Taurus and Sable vehicles equipped with 3.0L 4V Duratec engines and built at the Chicago assembly plant.In the dealer letter for the program, Ford indicates that the Speed Control Cables on affected vehicles may be susceptible to damage or becoming partially disconnected during under hood vehicle maintenance (e.g., replacing a battery or changing the air filter) and that a damaged Speed Control Cable could interfere with the throttle's full return to idle when the accelerator pedal is released.Ford's program instructs dealers to inspect the Speed Control Cables and replace any with any portion of either collar retention tab missing.Dealers will install a Collar Reinforcement Clip at the Speed Control Cable collar in all vehicles. Figure 1 shows the location of the Speed Control Cable in the engine compartment and the proximity of the battery and air filter.The failure mode of the cable assembly is associated with the plastic collar used to secure the cable to a bracket near the throttle body (Figure 2).Damage to one or both retention tabs used to secure the cable ferrule within the collar may allow the ferrule to become disconnected from the collar when the throttle is opened during accelerator pedal application.Additional examples of Speed Control Cables with damaged collar retention tabs and partial ferrule displacement are shown in Figures 3 through 5.If the displacement pulls the ferrule completely out of the collar, the ferrule end may contact the face of the collar when the accelerator pedal is released and the throttle is returning to idle (Figure 6).This results in a throttle stuck at approximately 26-29% open.Testing conducted at NHTSA's Vehicle Research and Test Center found that brake booster vacuum may become depleted, resulting in reduced brake effectiveness, if the brake is applied repeatedly when the throttle is stuck at this position.Drivers who experienced this condition have reported being surprised that the engine speed did not drop as expected and in some cases misjudged the degree of braking required to slow the vehicle.Some drivers reported difficulty in braking the vehicle and responded by shifting to neutral or turning the engine off.One minor crash occurred when the vehicle contacted a roadside fence post after the driver responded to the stuck throttle by shifting the car to neutral, turning the engine off and coasting to the side of a roadway with no shoulder, resulting in approximately $400 damage to the vehicle.There were four crashes reported which were attributed to increased stopping distance caused by the increased engine power and/or reduced brake effectiveness, including two of the complaints to ODI.In one crash reported to ODI (VOQ 10516101), the subject vehicle allegedly hit the back end of a truck at approximately 40 mph causing about $2000 damage.In the other crash complaint to ODI (VOQ 10501834), the subject vehicle side-swiped a vehicle as the driver was unable to stop in time and attempted to maneuver around a line of vehicles stopped at a traffic light.When the tow truck driver subsequently started the incident vehicle, the engine was still racing and it was verified that the Speed Control Cable ferrule was stuck on the collar.After further investigation, ODI does not consider the crashes reported in VOQs 10456249 and 10159399 to be related to the Speed Control Cable problem.
Vehicle Speed Control
On June 21, 2013, Ford initiated Customer Satisfaction Program 13B04 to address a concern with Speed Control Cable damage in certain model year (MY) 2000 through 2003 Taurus and Sable vehicles equipped with 3.0L 4V Duratec engines and built at the Chicago assembly plant.In the dealer letter for the program, Ford indicates that the Speed Control Cables on affected vehicles may be susceptible to damage or becoming partially disconnected during under hood vehicle maintenance (e.g., replacing a battery or changing the air filter) and that a damaged Speed Control Cable could interfere with the throttle's full return to idle when the accelerator pedal is released.Ford's program instructs dealers to inspect the Speed Control Cables and replace any with any portion of either collar retention tab missing.Dealers will install a Collar Reinforcement Clip at the Speed Control Cable collar in all vehicles. Figure 1 shows the location of the Speed Control Cable in the engine compartment and the proximity of the battery and air filter.The failure mode of the cable assembly is associated with the plastic collar used to secure the cable to a bracket near the throttle body (Figure 2).Damage to one or both retention tabs used to secure the cable ferrule within the collar may allow the ferrule to become disconnected from the collar when the throttle is opened during accelerator pedal application.Additional examples of Speed Control Cables with damaged collar retention tabs and partial ferrule displacement are shown in Figures 3 through 5.If the displacement pulls the ferrule completely out of the collar, the ferrule end may contact the face of the collar when the accelerator pedal is released and the throttle is returning to idle (Figure 6).This results in a throttle stuck at approximately 26-29% open.Testing conducted at NHTSA's Vehicle Research and Test Center found that brake booster vacuum may become depleted, resulting in reduced brake effectiveness, if the brake is applied repeatedly when the throttle is stuck at this position.Drivers who experienced this condition have reported being surprised that the engine speed did not drop as expected and in some cases misjudged the degree of braking required to slow the vehicle.Some drivers reported difficulty in braking the vehicle and responded by shifting to neutral or turning the engine off.One minor crash occurred when the vehicle contacted a roadside fence post after the driver responded to the stuck throttle by shifting the car to neutral, turning the engine off and coasting to the side of a roadway with no shoulder, resulting in approximately $400 damage to the vehicle.There were four crashes reported which were attributed to increased stopping distance caused by the increased engine power and/or reduced brake effectiveness, including two of the complaints to ODI.In one crash reported to ODI (VOQ 10516101), the subject vehicle allegedly hit the back end of a truck at approximately 40 mph causing about $2000 damage.In the other crash complaint to ODI (VOQ 10501834), the subject vehicle side-swiped a vehicle as the driver was unable to stop in time and attempted to maneuver around a line of vehicles stopped at a traffic light.When the tow truck driver subsequently started the incident vehicle, the engine was still racing and it was verified that the Speed Control Cable ferrule was stuck on the collar.After further investigation, ODI does not consider the crashes reported in VOQs 10456249 and 10159399 to be related to the Speed Control Cable problem.
EA08018 · Front Suspension Coil Spring Fracture
Opened Aug 28, 2008 · Closed Jun 30, 2011
Status: closed (inferred from source dates) · Suspension:front:springs:coil Springs
To date, ODI is aware of 2,401 non-duplicative complaints related to the alleged defect. In addition, ODI is aware of 1,411 subject vehicles with one or more warranty claims related to the alleged defect. In total, ODI is aware of 3,645 unique subject vehicles that have experienced one or more front suspension coil spring fractures. ODI is also aware of four minor crashes related to the alleged defect resulting in one minor injury.With greater than eight years of exposure, a large subject vehicle population and approximately 2,052 reported front tire punctures caused by fractured coil springs (at all speeds), there have been no reported severe crashes, deaths or injuries related to the alleged defect. The real world consequences of these defective coil springs have been a small number of minor control problems that resulted in minor damage; suggesting that the effect of the defect on vehicle control is minor.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted. Accordingly, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency will continue to monitor this issue and will take further action if warranted by the circumstances. See the EA08-018 Engineering Analysis Closing Report for more details.
RP03001 · Brake/accelerator Pedal Application
Opened Oct 31, 2003 · Closed Mar 23, 2004
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:pedals And Linkages
MS. RODMAN REPORTED THAT AFTER HER VEHICLE WAS INSPECTED FOR THE RECALL, HER MOTHER EXPERIENCED A SUDDEN ACCELERATION AND CRASHED THE SABLE INTO A LIGHT POLE.PREVIOUSLY NHTSA HAD CONDUCTED AN INVESTIGATION FOR THIS ISSUE (PE02-035) THAT RESULTED IN THE RECALL (02V-266) OF 369,000 MY 2000-2002 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE BRAKE AND ACCELERATOR PEDALS TO INSURE THAT THE SEPARATION BETWEEN THE PEDALS WAS AT LEAST 50MM..A REVIEW OF ODI'S DATABASE FOR COMPLAINTS REGARDING RECALL 02V-266 DID NOT IDENTIFY ANY RECALL REMEDY COMPLAINTS OTHER THAN THE PETITIONER'S.MS. RODMAN?S VEHICLE WAS INSPECTED BY ODI USING FORD?S SPECIAL TOOL AND HER VEHICLE WAS FOUND TO EXCEED 50MM.ALSO, THE LATERAL MOVEMENT OF THE PEDALS WAS FOUND NOT TO BE EXCESSIVE RELATIVE TO OTHER COMPARABLE TAURUS AND SABLE VEHICLES.THEREFORE, IT IS UNLIKELY THAT NHTSA WOULD ISSUE AN ORDER REQUIRING FORD TO PROVIDE A DIFFERENT REMEDY FOR THIS DEFECT.IN VIEW OF THE NEED TO ALLOCATE AND PRIORITIZE NHTSA?S LIMITED RESOURCES TO BEST ACCOMPLISH THE AGENCY?S SAFETY MISSION, THE PETITION IS DENIED.FOR ADDITIONAL INFORMATION CONCERNING THIS ANALYSIS, PLEASE REFER TO THE FEDERAL REGISTER NOTICE DATED MARCH 23, 2004 (VOL 69, NO 56, PAGES 13619-13620).
RQ03008 · Brake Light Switch Failure
Opened Oct 23, 2003 · Closed Mar 5, 2004
Status: closed (inferred from source dates) · Exterior Lighting; Exterior Lighting:brake Lights; Exterior Lighting:brake Lights:switch; Exterior Lighting:tail Lights; Exterior Lighting:tail Lights:switch
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Additional source detail variants (5)
Exterior Lighting:brake Lights
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Exterior Lighting:brake Lights:switch
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Exterior Lighting
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Exterior Lighting:tail Lights
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Exterior Lighting:tail Lights:switch
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.