Backing out of parking space resulting to damage to both vehicles . Brake\gas pedals. Position of driver ( body turned) relative to pedals while backing car can allow drivers foot to be in contact with both pedals. Increased pressure on the brake can allow increased pressure on the gas pedal allowing the vehicle to continu…
Read full complaint
Backing out of parking space resulting to damage to both vehicles . Brake\gas pedals. Position of driver ( body turned) relative to pedals while backing car can allow drivers foot to be in contact with both pedals. Increased pressure on the brake can allow increased pressure on the gas pedal allowing the vehicle to continue in a reversed direction . Can strike a person or object resulting in injury or damage. Subject car is a station wagon and appears to have lower seating \configuration than a sedan .
NHTSA ODI #11704207
Mileage unknown · Dec 11, 2020
Service BrakesSuspension
TL* THE CONTACT OWNS A 2002 FORD TAURUS. THE CONTACT STATED THAT THE BRAKE LIGHT STARTED TO FLASH WHILE DRIVING HOWEVER, THERE WAS NO BRAKE MALFUNCTION. THE VEHICLE WAS TAKEN TO AUBURN AUTOMOTIVE (500 S. OPDYKE RD, WATERFORD, MI 48328, (248) 332-9300) TO BE DIAGNOSED. THE CONTACT WAS INFORMED THAT THE UNDERCARRIAGE OF THE VEHICL…
Read full complaint
TL* THE CONTACT OWNS A 2002 FORD TAURUS. THE CONTACT STATED THAT THE BRAKE LIGHT STARTED TO FLASH WHILE DRIVING HOWEVER, THERE WAS NO BRAKE MALFUNCTION. THE VEHICLE WAS TAKEN TO AUBURN AUTOMOTIVE (500 S. OPDYKE RD, WATERFORD, MI 48328, (248) 332-9300) TO BE DIAGNOSED. THE CONTACT WAS INFORMED THAT THE UNDERCARRIAGE OF THE VEHICLE WAS EXTREMELY RUSTED AND THAT THE VEHICLE WAS UNSAFE TO DRIVE. THE MANUFACTURER WAS CONTACTED AND INFORMED OF THE FAILURE. THE FAILURE MILEAGE WAS UNKNOWN. *BF
NHTSA ODI #11383037
146,000 miles · Feb 1, 2018
Electrical SystemExterior LightingService Brakes
MY 2002 FORD TAURUS SUDDENLY WOULD NOT SHIFT OUT OF PARK. MY BACK DRIVER SIDE BRAKE LIGHT WON'T WORK. I LOOK IT UP AND SAW A RECALL BUT WHEN I CALLED THE DEALERSHIP THEY SAID THERE WASN'T A RECALL ON MY CAR. PLEASE HELP
NHTSA ODI #11066448
Mileage unknown · Jan 19, 2017
Service Brakes
THE BOSCH CO. HAS NOT GOT BACK TO ME ABOUT ITS BRAKE PAD RECALL (RECALL NOTICE 16E026) ON PADS PGD598. I CALLED STARTING IN OCTOBER OF LAST YEAR AND THEN TWO OR THREE MORE TIMES AND STILL NO RESPONSE.
NHTSA ODI #10946467
62,782 miles · Nov 18, 2016
Service Brakes
LATE SEPTEMBER EARLY OCTOBER I RECEIVED A LETTER FROM BOSCH ABOUT A RECALL ON BRAKE PADS I HAD GOTTEN FROM PEPBOYS. I WORK FOR A SCHOOL DISTRICT IN UTAH AND WE DO MOST OF THE WORK OUR SELF. SO I CALLED THEM AND THEY TOLD ME THEY WOULD CALL BACK TO TELL ME WHAT I NEED TO DO FOR THIS RECALL. AFTER 2 WEEKS AND NO CALL, I CALLED THE…
Read full complaint
LATE SEPTEMBER EARLY OCTOBER I RECEIVED A LETTER FROM BOSCH ABOUT A RECALL ON BRAKE PADS I HAD GOTTEN FROM PEPBOYS. I WORK FOR A SCHOOL DISTRICT IN UTAH AND WE DO MOST OF THE WORK OUR SELF. SO I CALLED THEM AND THEY TOLD ME THEY WOULD CALL BACK TO TELL ME WHAT I NEED TO DO FOR THIS RECALL. AFTER 2 WEEKS AND NO CALL, I CALLED THEM, THEY PUT ME ON HOLD AND NEVER GOT BACK. I CALLED AGAIN A FEW DAYS LATER AND WAS TRANSFERED TO A VOICE MAIL BOX THAT WAS FULL AND NOT TAKING MESSAGES. THIS CAR IS SITTING HERE FOR A MONTH AND WE ARE NOT ABLE TO USE IT BECAUSE OF THIS RECALL. THE SHIMS ON THE BACK OF THE PADS COMES OFF AND CUTS INTO THE ROTORS. ONE SIDE HAS DONE THIS AND THE OTHER IS JUST STARTING TO CUT INTO THE ROTOR. WHAT I WOULD LIKE TO KNOW IS THERE ANYTHING I CAN DO TO GET THEM TO SPEED UP WITH THIS.
NHTSA ODI #10927001
115,000 miles · Jul 6, 2016
Service Brakes
TL* THE CONTACT OWNS A 2002 FORD TAURUS. WHILE ATTEMPTING TO STOP THE VEHICLE, THE BRAKE PEDAL EXTENDED TO THE FLOORBOARD, BUT THE VEHICLE WOULD NOT IMMEDIATELY SLOW DOWN OR STOP. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHO DIAGNOSED THAT THE BRAKING SYSTEM WAS FAULTY. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS …
Read full complaint
TL* THE CONTACT OWNS A 2002 FORD TAURUS. WHILE ATTEMPTING TO STOP THE VEHICLE, THE BRAKE PEDAL EXTENDED TO THE FLOORBOARD, BUT THE VEHICLE WOULD NOT IMMEDIATELY SLOW DOWN OR STOP. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHO DIAGNOSED THAT THE BRAKING SYSTEM WAS FAULTY. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 115,000.
NHTSA ODI #10883047
116,500 miles · Sep 8, 2013
EngineService BrakesVehicle Speed Control
1ST MAJOR INCIDENT- ON SEPTEMBER 12TH -TRAVELING AT APPROX 50 MPH AND WHEN I TRIED TO BRAKE THE CAR WOULD NOT SLOW DOWN BUT STAYED OR EVEN ACCELERATED ITS SPEED.I EVENTUALLY WAS ABLE TO GET CONTROL OF THE CAR AND CONTINUED TO MY DESTINATION. MY WIFE CALLED THE SANDY SPRINGS FORD DEALERSHIP AND WE MADE AN APPOINTMENT TO DROP OFF …
Read full complaint
1ST MAJOR INCIDENT- ON SEPTEMBER 12TH -TRAVELING AT APPROX 50 MPH AND WHEN I TRIED TO BRAKE THE CAR WOULD NOT SLOW DOWN BUT STAYED OR EVEN ACCELERATED ITS SPEED.I EVENTUALLY WAS ABLE TO GET CONTROL OF THE CAR AND CONTINUED TO MY DESTINATION. MY WIFE CALLED THE SANDY SPRINGS FORD DEALERSHIP AND WE MADE AN APPOINTMENT TO DROP OFF THE CAR THE NEXT EVENING FOR SERVICE ON WEDNESDAY, AUGUST 14TH. THE FORD REP TOOK DOWN ALL OF MY INFORMATION BUT NEVER MENTIONED THE RECALL OR THE REPERCUSSIONS OF DRIVING THIS CAR AFTER THIS REPORTED INCIDENT. 2ND INCIDENT- ON SEPTEMBER 13TH - TRAVELING APPROX 50 MPH AND THEN ALL OF A SUDDEN I LOST COMPLETE CONTROL OF THE CAR AND FOR A FEW SECONDS I THOUGHT I WOULD NOT ONLY KILL MYSELF BUT OTHER INNOCENT PEOPLE ON THE FREEWAY. I MANAGED TO PULL THE CAR INTO AN APARTMENT COMPLEX PARKING LOT. I CALLED AAA AND THEY DELIVERED THE CAR TO THE SANDY SPRINGS FORD DEALERSHIP. MY WIFE CALLED THE CUSTOMER SERVICE THE NEXT DAY - SPOKE WITH KAREN. WHY WERE WE NOT TOLD ABOUT THE RECALL (DID RESEARCH ON THE INTERNET)? HER RESPONSE: THEY JUST FOUND OUT ABOUT IT THAT VERY SAME DAY. WE JUST RETURNED FROM VACATION AND OUR NEIGHBOR JUST DELIVERED OUR MAIL, WELL THERE WAS A LETTER FROM FORD ABOUT THE RECALL. THEN, ON FRIDAY SEPTEMBER 16TH WE RECEIVED AN AUTOMATED CALL FROM SANDY SPRINGS FORD ABOUT THE RECALL. DOES FORD HAVE ANY IDEA IN THE ACT OF NEGLIGENCE THEY HAVE CREATED? THERE COULD HAVE BEEN FATALITIES. OUR CAR IS STILL AT THE FORD DEALERSHIP - IT IS STALLING OUT AND THE BRAKES WERE NOT THE SAME (CHARGED US TO FIX THEM). FORD SAID THE SPEED CONTROL CABLE WAS COMPLETELY BROKEN OFF AND THEY WERE REQUIRED TO REPORT IT AND MAIL YOU THE PART. WAS THIS DONE? FOR THE LIFE OF ME, I CAN NOT FATHOM THAT A CAR MANUFACTURER WOULD NOT HAVE ALERTED THEIR DEALERS ABOUT THIS RECALL. I SHOULD HAVE BEEN ALERTED AND WARNED ON MONDAY EVENING AND TOLD DO NOT DRIVE THE CAR.
NHTSA ODI #10542506
109,930 miles · Jun 10, 2013
Service BrakesVehicle Speed ControlInjury
WAS COMING OFF US 501 IN CONWAY SC AND HEARD A LOAD POP SOUND PUT BRAKES ON AND CAR KEEP ON GOING IT WOULD NOT STOP THE BRAKES WOULD NOT STOP THE CAR IT KEEP RACING UP. HAD NO WERE TO GO BUT THE BACK END OF A GMC TRUCK. CAR WAS TOWED TO CONWAY FORD. ON 6/10/2013 TALK TO SERVICE AND THEY SAID THEY TRIED TO DRIVE THE CAR ON THE …
Read full complaint
WAS COMING OFF US 501 IN CONWAY SC AND HEARD A LOAD POP SOUND PUT BRAKES ON AND CAR KEEP ON GOING IT WOULD NOT STOP THE BRAKES WOULD NOT STOP THE CAR IT KEEP RACING UP. HAD NO WERE TO GO BUT THE BACK END OF A GMC TRUCK. CAR WAS TOWED TO CONWAY FORD. ON 6/10/2013 TALK TO SERVICE AND THEY SAID THEY TRIED TO DRIVE THE CAR ON THE LOT AND IT DID IT TO THEM.. THE DIAG. WAS CRUISE CONTROL BROKE PLUS THE ACTUATOR ASY. ON THIS YEAR CRUISE CONTROL CABLE AND ACCELERATOR CABLE ARE CONNECTED TO THROTTLE BODY ON THE SAME LINKAGE. WHEN CRUISE CABLE BROKE IT CAUSED THE THROTTLE BODY LINKAGE TO NOT RETURN TO IDLE POSITION. CRUISE CONTROL WAS NOT ON WHEN THIS HAPPENED. *TR
NHTSA ODI #10516101
165,000 miles · Apr 30, 2013
Electrical SystemService BrakesSuspension
I LOOKED UP MY CAR RECALLS AND THERE WHERE 3 AND WHEN I CALLED FORD THEY TOLD ME THAT THIS WEBSITE IS WRONG AND THERE IS NO RECALLS. EVEN WHEN EVERYTHING THAT IS WRONG WITH MY CAR IS ON THE RECALLS. I JUST NEED TO KNOWN WHAT TO DO NOW. *TR
NHTSA ODI #10510054
12,500 miles · Oct 3, 2012
Service Brakes
TL* THE CONTACT OWNS A 2002 FORD TAURUS. THE CONTACT STATED THAT WHILE STOPPED AT A TRAFFIC LIGHT WITH THE BRAKE PEDAL DEPRESSED THE ENGINE BEGAN TO REV UP. THE CONTACT HEARD A GROWLING AND RUMBLING NOISE COMING FROM THE ENGINE. AS A RESULT, THE CONTACT SHIFTED THE VEHICLE IN PARK AND TURNED THE ENGINE OFF. AFTER RESTARTING THE …
Read full complaint
TL* THE CONTACT OWNS A 2002 FORD TAURUS. THE CONTACT STATED THAT WHILE STOPPED AT A TRAFFIC LIGHT WITH THE BRAKE PEDAL DEPRESSED THE ENGINE BEGAN TO REV UP. THE CONTACT HEARD A GROWLING AND RUMBLING NOISE COMING FROM THE ENGINE. AS A RESULT, THE CONTACT SHIFTED THE VEHICLE IN PARK AND TURNED THE ENGINE OFF. AFTER RESTARTING THE VEHICLE THE FAILURE DID NOT RECURRED. THE FAILURE OCCURRED FOUR DIFFERENT TIMES INTERMITTENTLY. THE VEHICLE WAS NOT TAKEN TO THE DEALER. THERE WAS A RECALL UNDER NHTSA CAMPAIGN ID NUMBER: 02V266000 (SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES) THAT MAY BE RELATED TO THE FAILURE. THE MANUFACTURER WAS CONTACTED PRIOR TO THE FAILURE AND STATED THE VEHICLE WAS NOT INCLUDED IN ANY RECALL. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 12,500.
CERTAIN PASSENGER VEHICLES ARE BEING RECALLED TO CORRECT A PROBLEM WITH A MALFUNCTIONING STOP LAMP SWITCH AND/OR ASSOCIATED WIRING. THIS MALFUNCTIONING COULD RENDER THE STOP LAMPS INOPERABLE OR CAUSE THEM TO STAY ON ALL THE TIME. THIS COULD CAUSE CONFUSION TO A FOLLOWING DRIVER, WHICH COULD LEAD TO A CRASH.
Consequence & remedy
Consequence: IN ADDITION, IF THE SWITCH AND/OR ASSOCIATED WIRING FAIL IN THE OPEN POSITION, THE BRAKE LIGHTS WILL NOT ACTUATE AND THE DRIVER WILL NOT BE ABLE TO SHIFT THE VEHICLE OUT OF "PARK" IF THEY FAIL IN THE CLOSED POSITION, THE BRAKE LIGHTS WILL REMAIN ON, WHICH WILL NOT ALLOW THE SPEED CONTROL TO BE ACTIVATED. THIS COULD ALSO CAUSE THE BATTERY TO DISCHARGE.
Remedy: DEALERS WILL REMOVE THE STOP LAMP SWITCH AND ASSOCIATED WIRING ASSEMBLY AND INSTALL A NEWLY DESIGNED STOP LAMP SWITCH AND WIRE ASSEMBLY. OWNER NOTIFICATION IS EXPECTED TO BEGIN ON APRIL 5, 2004. OWNERS SHOULD CONTACT FORD AT 1-800-392-3673.
CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, "WINDSHIELD MOUNTING." THE WINDSHIELDS MAY POTENTIALLY EXHIBIT INCREASED WIND NOISE, WATER LEAKAGE, AND SQUEAKS AND RATTLES.
Consequence & remedy
Consequence: POTENTIAL LOSS OF WINDSHIELD RETENTION MAY ALSO REDUCE OCCUPANT PROTECTION IN THE EVENT OF A CRASH.
Remedy: DEALERS WILL REPLACE THESE WINDSHIELDS. OWNER NOTIFICATION BEGAN ON MARCH 31, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD/MERCURY AT 1-800-392-3673.
CERTAIN PASSENGER VEHICLES EQUIPPED WITH ADJUSTABLE PADELS ARE BEING RECALLED IN ORDER TO ADJUST THE BRAKE AND ACCELERATOR PEDALS TO A MINIMUM OF 50 MM OF LATERAL SEPARATION. SIMULTANEOUS APPLICATION OF BOTH THE BRAKE AND ACCELERATOR PEDALS COULD RESULT IN AN INCREASE IN ENGINE RPM.
Consequence & remedy
Consequence: THIS COULD RESULT IN A CUSTOMER EXPERIENCING AN "UNINTENDED VEHICLE SPEED INCREASE" OR A PERCEIVED "UNABLE TO STOP" CONDITION.
Remedy: OWNERS WILL BE INSTRUCTED AS TO THE PROPER WAY TO SET THE POSITION OF THE PEDALS AND TO TAKE THEIR VEHICLES TO A DEALER TO HAVE THE SPACING BETWEEN THE BRAKE AND ACCELERATOR PEDALS MEASURED. IF THE SPACING IS FOUND TO BE LESS THAN 50 MM, THE DEALER WILL ADJUST THE PEDALS TO INCREASE THE DISTANCE BETWEEN THEM TO GREATER THAN 50 MM. OWNER NOTIFICATION BEGAN OCTOBER 28, 2002. OWNERS WHO DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4
PE12033 · Speed Control Cable Damage
Opened Oct 24, 2012 · Closed Jun 26, 2013
Status: closed (inferred from source dates) · Vehicle Speed Control; Vehicle Speed Control:cables; Vehicle Speed Control:cruise Control
On June 21, 2013, Ford initiated Customer Satisfaction Program 13B04 to address a concern with Speed Control Cable damage in certain model year (MY) 2000 through 2003 Taurus and Sable vehicles equipped with 3.0L 4V Duratec engines and built at the Chicago assembly plant.In the dealer letter for the program, Ford indicates that the Speed Control Cables on affected vehicles may be susceptible to damage or becoming partially disconnected during under hood vehicle maintenance (e.g., replacing a battery or changing the air filter) and that a damaged Speed Control Cable could interfere with the throttle's full return to idle when the accelerator pedal is released.Ford's program instructs dealers to inspect the Speed Control Cables and replace any with any portion of either collar retention tab missing.Dealers will install a Collar Reinforcement Clip at the Speed Control Cable collar in all vehicles. Figure 1 shows the location of the Speed Control Cable in the engine compartment and the proximity of the battery and air filter.The failure mode of the cable assembly is associated with the plastic collar used to secure the cable to a bracket near the throttle body (Figure 2).Damage to one or both retention tabs used to secure the cable ferrule within the collar may allow the ferrule to become disconnected from the collar when the throttle is opened during accelerator pedal application.Additional examples of Speed Control Cables with damaged collar retention tabs and partial ferrule displacement are shown in Figures 3 through 5.If the displacement pulls the ferrule completely out of the collar, the ferrule end may contact the face of the collar when the accelerator pedal is released and the throttle is returning to idle (Figure 6).This results in a throttle stuck at approximately 26-29% open.Testing conducted at NHTSA's Vehicle Research and Test Center found that brake booster vacuum may become depleted, resulting in reduced brake effectiveness, if the brake is applied repeatedly when the throttle is stuck at this position.Drivers who experienced this condition have reported being surprised that the engine speed did not drop as expected and in some cases misjudged the degree of braking required to slow the vehicle.Some drivers reported difficulty in braking the vehicle and responded by shifting to neutral or turning the engine off.One minor crash occurred when the vehicle contacted a roadside fence post after the driver responded to the stuck throttle by shifting the car to neutral, turning the engine off and coasting to the side of a roadway with no shoulder, resulting in approximately $400 damage to the vehicle.There were four crashes reported which were attributed to increased stopping distance caused by the increased engine power and/or reduced brake effectiveness, including two of the complaints to ODI.In one crash reported to ODI (VOQ 10516101), the subject vehicle allegedly hit the back end of a truck at approximately 40 mph causing about $2000 damage.In the other crash complaint to ODI (VOQ 10501834), the subject vehicle side-swiped a vehicle as the driver was unable to stop in time and attempted to maneuver around a line of vehicles stopped at a traffic light.When the tow truck driver subsequently started the incident vehicle, the engine was still racing and it was verified that the Speed Control Cable ferrule was stuck on the collar.After further investigation, ODI does not consider the crashes reported in VOQs 10456249 and 10159399 to be related to the Speed Control Cable problem.
Additional source detail variants (3)
Vehicle Speed Control:cables
On June 21, 2013, Ford initiated Customer Satisfaction Program 13B04 to address a concern with Speed Control Cable damage in certain model year (MY) 2000 through 2003 Taurus and Sable vehicles equipped with 3.0L 4V Duratec engines and built at the Chicago assembly plant.In the dealer letter for the program, Ford indicates that the Speed Control Cables on affected vehicles may be susceptible to damage or becoming partially disconnected during under hood vehicle maintenance (e.g., replacing a battery or changing the air filter) and that a damaged Speed Control Cable could interfere with the throttle's full return to idle when the accelerator pedal is released.Ford's program instructs dealers to inspect the Speed Control Cables and replace any with any portion of either collar retention tab missing.Dealers will install a Collar Reinforcement Clip at the Speed Control Cable collar in all vehicles. Figure 1 shows the location of the Speed Control Cable in the engine compartment and the proximity of the battery and air filter.The failure mode of the cable assembly is associated with the plastic collar used to secure the cable to a bracket near the throttle body (Figure 2).Damage to one or both retention tabs used to secure the cable ferrule within the collar may allow the ferrule to become disconnected from the collar when the throttle is opened during accelerator pedal application.Additional examples of Speed Control Cables with damaged collar retention tabs and partial ferrule displacement are shown in Figures 3 through 5.If the displacement pulls the ferrule completely out of the collar, the ferrule end may contact the face of the collar when the accelerator pedal is released and the throttle is returning to idle (Figure 6).This results in a throttle stuck at approximately 26-29% open.Testing conducted at NHTSA's Vehicle Research and Test Center found that brake booster vacuum may become depleted, resulting in reduced brake effectiveness, if the brake is applied repeatedly when the throttle is stuck at this position.Drivers who experienced this condition have reported being surprised that the engine speed did not drop as expected and in some cases misjudged the degree of braking required to slow the vehicle.Some drivers reported difficulty in braking the vehicle and responded by shifting to neutral or turning the engine off.One minor crash occurred when the vehicle contacted a roadside fence post after the driver responded to the stuck throttle by shifting the car to neutral, turning the engine off and coasting to the side of a roadway with no shoulder, resulting in approximately $400 damage to the vehicle.There were four crashes reported which were attributed to increased stopping distance caused by the increased engine power and/or reduced brake effectiveness, including two of the complaints to ODI.In one crash reported to ODI (VOQ 10516101), the subject vehicle allegedly hit the back end of a truck at approximately 40 mph causing about $2000 damage.In the other crash complaint to ODI (VOQ 10501834), the subject vehicle side-swiped a vehicle as the driver was unable to stop in time and attempted to maneuver around a line of vehicles stopped at a traffic light.When the tow truck driver subsequently started the incident vehicle, the engine was still racing and it was verified that the Speed Control Cable ferrule was stuck on the collar.After further investigation, ODI does not consider the crashes reported in VOQs 10456249 and 10159399 to be related to the Speed Control Cable problem.
Vehicle Speed Control:cruise Control
On June 21, 2013, Ford initiated Customer Satisfaction Program 13B04 to address a concern with Speed Control Cable damage in certain model year (MY) 2000 through 2003 Taurus and Sable vehicles equipped with 3.0L 4V Duratec engines and built at the Chicago assembly plant.In the dealer letter for the program, Ford indicates that the Speed Control Cables on affected vehicles may be susceptible to damage or becoming partially disconnected during under hood vehicle maintenance (e.g., replacing a battery or changing the air filter) and that a damaged Speed Control Cable could interfere with the throttle's full return to idle when the accelerator pedal is released.Ford's program instructs dealers to inspect the Speed Control Cables and replace any with any portion of either collar retention tab missing.Dealers will install a Collar Reinforcement Clip at the Speed Control Cable collar in all vehicles. Figure 1 shows the location of the Speed Control Cable in the engine compartment and the proximity of the battery and air filter.The failure mode of the cable assembly is associated with the plastic collar used to secure the cable to a bracket near the throttle body (Figure 2).Damage to one or both retention tabs used to secure the cable ferrule within the collar may allow the ferrule to become disconnected from the collar when the throttle is opened during accelerator pedal application.Additional examples of Speed Control Cables with damaged collar retention tabs and partial ferrule displacement are shown in Figures 3 through 5.If the displacement pulls the ferrule completely out of the collar, the ferrule end may contact the face of the collar when the accelerator pedal is released and the throttle is returning to idle (Figure 6).This results in a throttle stuck at approximately 26-29% open.Testing conducted at NHTSA's Vehicle Research and Test Center found that brake booster vacuum may become depleted, resulting in reduced brake effectiveness, if the brake is applied repeatedly when the throttle is stuck at this position.Drivers who experienced this condition have reported being surprised that the engine speed did not drop as expected and in some cases misjudged the degree of braking required to slow the vehicle.Some drivers reported difficulty in braking the vehicle and responded by shifting to neutral or turning the engine off.One minor crash occurred when the vehicle contacted a roadside fence post after the driver responded to the stuck throttle by shifting the car to neutral, turning the engine off and coasting to the side of a roadway with no shoulder, resulting in approximately $400 damage to the vehicle.There were four crashes reported which were attributed to increased stopping distance caused by the increased engine power and/or reduced brake effectiveness, including two of the complaints to ODI.In one crash reported to ODI (VOQ 10516101), the subject vehicle allegedly hit the back end of a truck at approximately 40 mph causing about $2000 damage.In the other crash complaint to ODI (VOQ 10501834), the subject vehicle side-swiped a vehicle as the driver was unable to stop in time and attempted to maneuver around a line of vehicles stopped at a traffic light.When the tow truck driver subsequently started the incident vehicle, the engine was still racing and it was verified that the Speed Control Cable ferrule was stuck on the collar.After further investigation, ODI does not consider the crashes reported in VOQs 10456249 and 10159399 to be related to the Speed Control Cable problem.
Vehicle Speed Control
On June 21, 2013, Ford initiated Customer Satisfaction Program 13B04 to address a concern with Speed Control Cable damage in certain model year (MY) 2000 through 2003 Taurus and Sable vehicles equipped with 3.0L 4V Duratec engines and built at the Chicago assembly plant.In the dealer letter for the program, Ford indicates that the Speed Control Cables on affected vehicles may be susceptible to damage or becoming partially disconnected during under hood vehicle maintenance (e.g., replacing a battery or changing the air filter) and that a damaged Speed Control Cable could interfere with the throttle's full return to idle when the accelerator pedal is released.Ford's program instructs dealers to inspect the Speed Control Cables and replace any with any portion of either collar retention tab missing.Dealers will install a Collar Reinforcement Clip at the Speed Control Cable collar in all vehicles. Figure 1 shows the location of the Speed Control Cable in the engine compartment and the proximity of the battery and air filter.The failure mode of the cable assembly is associated with the plastic collar used to secure the cable to a bracket near the throttle body (Figure 2).Damage to one or both retention tabs used to secure the cable ferrule within the collar may allow the ferrule to become disconnected from the collar when the throttle is opened during accelerator pedal application.Additional examples of Speed Control Cables with damaged collar retention tabs and partial ferrule displacement are shown in Figures 3 through 5.If the displacement pulls the ferrule completely out of the collar, the ferrule end may contact the face of the collar when the accelerator pedal is released and the throttle is returning to idle (Figure 6).This results in a throttle stuck at approximately 26-29% open.Testing conducted at NHTSA's Vehicle Research and Test Center found that brake booster vacuum may become depleted, resulting in reduced brake effectiveness, if the brake is applied repeatedly when the throttle is stuck at this position.Drivers who experienced this condition have reported being surprised that the engine speed did not drop as expected and in some cases misjudged the degree of braking required to slow the vehicle.Some drivers reported difficulty in braking the vehicle and responded by shifting to neutral or turning the engine off.One minor crash occurred when the vehicle contacted a roadside fence post after the driver responded to the stuck throttle by shifting the car to neutral, turning the engine off and coasting to the side of a roadway with no shoulder, resulting in approximately $400 damage to the vehicle.There were four crashes reported which were attributed to increased stopping distance caused by the increased engine power and/or reduced brake effectiveness, including two of the complaints to ODI.In one crash reported to ODI (VOQ 10516101), the subject vehicle allegedly hit the back end of a truck at approximately 40 mph causing about $2000 damage.In the other crash complaint to ODI (VOQ 10501834), the subject vehicle side-swiped a vehicle as the driver was unable to stop in time and attempted to maneuver around a line of vehicles stopped at a traffic light.When the tow truck driver subsequently started the incident vehicle, the engine was still racing and it was verified that the Speed Control Cable ferrule was stuck on the collar.After further investigation, ODI does not consider the crashes reported in VOQs 10456249 and 10159399 to be related to the Speed Control Cable problem.
EA08018 · Front Suspension Coil Spring Fracture
Opened Aug 28, 2008 · Closed Jun 30, 2011
Status: closed (inferred from source dates) · Suspension:front:springs:coil Springs
To date, ODI is aware of 2,401 non-duplicative complaints related to the alleged defect. In addition, ODI is aware of 1,411 subject vehicles with one or more warranty claims related to the alleged defect. In total, ODI is aware of 3,645 unique subject vehicles that have experienced one or more front suspension coil spring fractures. ODI is also aware of four minor crashes related to the alleged defect resulting in one minor injury.With greater than eight years of exposure, a large subject vehicle population and approximately 2,052 reported front tire punctures caused by fractured coil springs (at all speeds), there have been no reported severe crashes, deaths or injuries related to the alleged defect. The real world consequences of these defective coil springs have been a small number of minor control problems that resulted in minor damage; suggesting that the effect of the defect on vehicle control is minor.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted. Accordingly, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency will continue to monitor this issue and will take further action if warranted by the circumstances. See the EA08-018 Engineering Analysis Closing Report for more details.
RP03001 · Brake/accelerator Pedal Application
Opened Oct 31, 2003 · Closed Mar 23, 2004
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:pedals And Linkages
MS. RODMAN REPORTED THAT AFTER HER VEHICLE WAS INSPECTED FOR THE RECALL, HER MOTHER EXPERIENCED A SUDDEN ACCELERATION AND CRASHED THE SABLE INTO A LIGHT POLE.PREVIOUSLY NHTSA HAD CONDUCTED AN INVESTIGATION FOR THIS ISSUE (PE02-035) THAT RESULTED IN THE RECALL (02V-266) OF 369,000 MY 2000-2002 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE BRAKE AND ACCELERATOR PEDALS TO INSURE THAT THE SEPARATION BETWEEN THE PEDALS WAS AT LEAST 50MM..A REVIEW OF ODI'S DATABASE FOR COMPLAINTS REGARDING RECALL 02V-266 DID NOT IDENTIFY ANY RECALL REMEDY COMPLAINTS OTHER THAN THE PETITIONER'S.MS. RODMAN?S VEHICLE WAS INSPECTED BY ODI USING FORD?S SPECIAL TOOL AND HER VEHICLE WAS FOUND TO EXCEED 50MM.ALSO, THE LATERAL MOVEMENT OF THE PEDALS WAS FOUND NOT TO BE EXCESSIVE RELATIVE TO OTHER COMPARABLE TAURUS AND SABLE VEHICLES.THEREFORE, IT IS UNLIKELY THAT NHTSA WOULD ISSUE AN ORDER REQUIRING FORD TO PROVIDE A DIFFERENT REMEDY FOR THIS DEFECT.IN VIEW OF THE NEED TO ALLOCATE AND PRIORITIZE NHTSA?S LIMITED RESOURCES TO BEST ACCOMPLISH THE AGENCY?S SAFETY MISSION, THE PETITION IS DENIED.FOR ADDITIONAL INFORMATION CONCERNING THIS ANALYSIS, PLEASE REFER TO THE FEDERAL REGISTER NOTICE DATED MARCH 23, 2004 (VOL 69, NO 56, PAGES 13619-13620).
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Additional source detail variants (5)
Exterior Lighting:brake Lights
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Exterior Lighting:brake Lights:switch
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Exterior Lighting
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Exterior Lighting:tail Lights
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Exterior Lighting:tail Lights:switch
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
2002 Ford Taurus Problems, Complaints & Recalls | Skip That Year
Illustration