Ford issued a notice in 2018 TSB 18-2256 stating that they knew evaporator cores were leaking refrigerant into the cabin of the cars but did not issue a recall. I know this issue may not lead directly lead to an injury from an accident but the system failure does release toxic chemicals that should not be in the cabin of a vehi…
Read full complaint
Ford issued a notice in 2018 TSB 18-2256 stating that they knew evaporator cores were leaking refrigerant into the cabin of the cars but did not issue a recall. I know this issue may not lead directly lead to an injury from an accident but the system failure does release toxic chemicals that should not be in the cabin of a vehicle. Because this is a health risk to the occupants of the affected vehicles there should be a recall. I have had my 2016 Ford Mustang in to the Ford mechanic no less than 4 times since I bought it in late 2016 and each time they came up with some new cause for my AC not working and each time the system failed again in less than 2 years. Each time the problem was a supposed refrigerant leak in some other component of the AC system. Now that they've run out of things to replace they have speculated that the most likely cause is a bad evaporator core. My suspicion is that the evaporator core has been the issue from the beginning. Since Ford didn't issue a recall I have been subjected to years of exposure to dangerous chemicals due to this issue. Please make for recall these vehicles for the safety of the occupants of the affected vehicles
NHTSA ODI #11625502
Mileage unknown · Oct 3, 2024
Back Over PreventionUnknown Or Other
In March 2023 safety recall 22V082000 (Ford Number 22S06) was performed to fix a rear view camera malfunction. During the March 2023 work, only the wiring harness was replaced. My belief was that the actual camera should have been replaced as well. Replacing the wiring harness in March 2023 fixed the issue for 13 months, and …
Read full complaint
In March 2023 safety recall 22V082000 (Ford Number 22S06) was performed to fix a rear view camera malfunction. During the March 2023 work, only the wiring harness was replaced. My belief was that the actual camera should have been replaced as well. Replacing the wiring harness in March 2023 fixed the issue for 13 months, and then the issue re-occurred. Dealership charged $230 diagnosis fee to tell me that the issue was the camera and now the replacement of the camera cost me the $230 diagnostic fee; The $75 part fee for the camera; and the labor to replace the camera - Total bill out of pocket $530. I was informed after calling the Main Ford Customer service number that my 2016 mustang was not part of the camera recall (only the wiring harness). Camera was only covered with 2015 mustang. Seems odd to me that they make that distinction between model years but it is the same camera and obviously failed on my vehicle. As a major safety concern I believe Ford has failed to support their customers regarding this issue, and a second recall is warranted for the camera portion on 2016 models as well.
NHTSA ODI #11617845
Mileage unknown · Sep 23, 2024
Unknown Or Other
The rearview can result in a blank or have distorted image. As in NHTSA Campaign Number: 22V082000
NHTSA ODI #11616058
Mileage unknown · Jul 14, 2024
Electrical SystemUnknown Or Other
Backup camera fails after recall repair is performed
NHTSA ODI #11601845
Mileage unknown · Jun 1, 2024
Unknown Or Other
Leaking evaporator core, seems to be very common with ‘15-‘17 Mustangs and Ford has done nothing about it.
NHTSA ODI #11591865
Mileage unknown · May 25, 2024
Unknown Or Other
Passenger door suddenly opens while driving even with doors locked . It’s all over in forums online. Ford won’t cover and sometimes won’t even fix the issue. Has happened on a few occasions already
NHTSA ODI #11590716
Mileage unknown · Mar 17, 2024
Electrical SystemUnknown Or OtherVisibility/wiper
Back up camera recall was unresolved by previous owner. I’ve tried fixing the issue myself but cannot find it. The camera displays blue and black screens while in reverse.
NHTSA ODI #11577894
Mileage unknown · Feb 28, 2024
Unknown Or Other
UNKNOWN
NHTSA ODI #11574494
Mileage unknown · Oct 25, 2023
StructureUnknown Or Other
The passenger door opens on it's own while in motion. I am afraid my passenger will fall out of the car. The dealership will do nothing since they can not spontaneously make it happen in the short ride they take it on. This happens on a weekly basis. Been happening now for at least 2 years
NHTSA ODI #11551864
Mileage unknown · Oct 19, 2023
Latches/locks/linkagesUnknown Or Other
While driving the doors will open to the secondary latch.
Ford Motor Company (Ford) is recalling certain 2015-2017 Mustang vehicles. Water and road salt may corrode the front seat belt anchor pretensioner cables.
Consequence & remedy
Consequence: A corroded cable can break, preventing the seat belt from properly restraining an occupant, and increasing the risk of injury during a crash.
Remedy: Dealers will inspect and replace both front seat belt anchor pretensioner assemblies, as necessary. In addition, dealers will remove sections of the carpet and underlayment that contact the cables. Dealers will also inspect the A-pillar sealing patches, and as necessary, install A-pillar body plugs, and/or inspect and replace the front outboard seat bolts. Repairs will be performed free of charge. Interim letters, notifying owners of the safety risk, were mailed October 20, 2025. Additional letters will be sent once the final remedy is available, anticipated December 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S92. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov September 17, 2025.
Ford Motor Company (Ford) is recalling certain 2015-2019 Lincoln MKC, Mustang, F-350 SD, F-250 SD, F-450 SD, 2015-2017 Lincoln Navigator, Expedition, 2015-2018 Edge, Transit Connect, 2016-2019 F-550 SD, Transit, 2017-2019 Econoline, and 2019 Ranger vehicles. The rearview camera may display a distorted, inverted, or blank image when the vehicle is in reverse.
Consequence & remedy
Consequence: A rearview camera that displays an inverted, distorted, or blank image can reduce the driver’s view behind the vehicle, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the rearview camera as necessary, free of charge. Owner notification letters were mailed January 13, 2026. Ford owners will receive letters in phases, beginning January 2026 and June 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S89. This recall expands previous NHTSA recall number 25V270. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning September 8, 2025.
Ford Motor Company (Ford) is recalling certain 2015-2017 Mustang vehicles. The rearview camera wiring may be loose or damaged, which can result in a blank or distorted image.
Consequence & remedy
Consequence: A rearview camera that displays a blank or distorted image can reduce the driver's rear view, increasing the risk of a crash.
Remedy: Dealers will inspect and repair the decklid wiring harness and/or replace the rearview camera, as necessary, free of charge. Owner notification letters were mailed December 23, 2022 and June 26, 2023. Remedy parts are expected to become available in the 4th Quarter of 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S06.
Ford Motor Company (Ford) is recalling certain model year 2015-2017 Mustang vehicles manufactured February 24, 2015, to August 30, 2016. A hose may separate from the engine oil cooler tube assembly causing an oil leak.
Consequence & remedy
Consequence: A sudden loss of engine oil may cause engine failure, increasing the risk of a crash. Additionally, an oil leak, in the presence of an ignition source, increases the risk of a fire.
Remedy: Ford will notify owners, and dealers will replace the engine oil cooler tube assembly, free of charge. The recall began on March 23, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S40.
Ford Motor Company (Ford) is recalling certain model year 2016 Ford Mustang vehicles manufactured September 26, 2015, to October 1, 2015. The front and rear seat belts and child seat tether anchors may have been damaged in shipping from the supplier to the vehicle assembly plant and may not adequately restrain the occupant in a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 208, "Occupant Crash Protection," and 225, "Child restraint anchorage systems."
Consequence & remedy
Consequence: If the restraint components do not function as intended, the occupants may not be properly restrained in the event of a crash, increasing their risk of injury.
Remedy: Ford will notify owners, and dealers will replace the front and rear seat belt assemblies and the child seat tether anchors, free of charge. The recall began on December 18, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15C13.
Additional source detail variants (2)
Child Seat:tether: Connector/clip
Ford Motor Company (Ford) is recalling certain model year 2016 Ford Mustang vehicles manufactured September 26, 2015, to October 1, 2015. The front and rear seat belts and child seat tether anchors may have been damaged in shipping from the supplier to the vehicle assembly plant and may not adequately restrain the occupant in a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 208, "Occupant Crash Protection," and 225, "Child restraint anchorage systems."
Consequence: If the restraint components do not function as intended, the occupants may not be properly restrained in the event of a crash, increasing their risk of injury.
Remedy: Ford will notify owners, and dealers will replace the front and rear seat belt assemblies and the child seat tether anchors, free of charge. The recall began on December 18, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15C13.
Seat Belts
Ford Motor Company (Ford) is recalling certain model year 2016 Ford Mustang vehicles manufactured September 26, 2015, to October 1, 2015. The front and rear seat belts and child seat tether anchors may have been damaged in shipping from the supplier to the vehicle assembly plant and may not adequately restrain the occupant in a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 208, "Occupant Crash Protection," and 225, "Child restraint anchorage systems."
Consequence: If the restraint components do not function as intended, the occupants may not be properly restrained in the event of a crash, increasing their risk of injury.
Remedy: Ford will notify owners, and dealers will replace the front and rear seat belt assemblies and the child seat tether anchors, free of charge. The recall began on December 18, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15C13.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
2016 Ford Mustang Problems, Complaints & Recalls | Skip That Year
Illustration