NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
135 reportsMileage unknown · Aug 21, 2023
Electrical SystemEngineFuel/propulsion System
I bought a 2022 mustang Mach e. Which was supposedly fixed at the factory in regards to the HVBJB issue. However, in mid 2023, my vehicle suffered a limp mode/warning about reduced power while on the interstate, was limited to about 60mph with very poor acceleration. Was diagnosed by ford tech as a failure of the recalled part a…
Read full complaint
I bought a 2022 mustang Mach e. Which was supposedly fixed at the factory in regards to the HVBJB issue. However, in mid 2023, my vehicle suffered a limp mode/warning about reduced power while on the interstate, was limited to about 60mph with very poor acceleration. Was diagnosed by ford tech as a failure of the recalled part and required HVBJB and BECM replacement, similar to 22V-412 recall. I think this should be added to RQ23004 investigation, as these vehicles had both the new hardware and software and were supposed to be “fixed”.
NHTSA ODI #11539783
Mileage unknown · Aug 14, 2023
Suspension
The stock suspension is dangerously defective. Both front and rear suspension do zero dampening and rebound necessary to keep the vehicle tires in contact with the road. When driving 50 to 70miles an hour on the highway, whenever I encountered a regular dip on an overpass, the front and rear wheels go slightly airborne. On sev…
Read full complaint
The stock suspension is dangerously defective. Both front and rear suspension do zero dampening and rebound necessary to keep the vehicle tires in contact with the road. When driving 50 to 70miles an hour on the highway, whenever I encountered a regular dip on an overpass, the front and rear wheels go slightly airborne. On several occasions driving on I-69 in Houston area, at one of the curved overpasses near Hilcroft Rd, slightly rainy wet and slick highway road, at 55 mph, my Mach E went airborne for a split second after passing thru one of the normal dips or seams on the concrete highways. I felt the vehicle was out of control going airborne for a split second and then regaining control after the up and down bounce subsided. I complained to my dealer (Helfman Ford). Their response was... they couldn't do much about the suspension because there were no recalls nor TSBs. However, they were able to log the complaint directly to Ford. I don't know the exact date of occurence, but one of the instances was sometime in the month of April 2023.
NHTSA ODI #11538480
Mileage unknown · Aug 14, 2023
Electrical SystemPower TrainUnknown Or Other
Was driving home, and all of a sudden I got a "Service Vehicle Soon" on the screen. and Got the following errors on FordPass App: 1- Powertrain Malfunction / Reduced Power 2- High-Voltage Battery Warning The time was around 8:30pm, the weather wasn't too hot not too cold. Was driving around 50 mph IIRC.
NHTSA ODI #11538373
Mileage unknown · Aug 2, 2023
Power Train
The vehicle stopped moving in the middle of travel. There was no indicator or warning. The car was towed to a service center and diagnosed that the back motor of the car was broken. Ford did not have any updates nor fixing the problem.
NHTSA ODI #11536062
Mileage unknown · Aug 1, 2023
Unknown Or Other
They Crystal of they roof is broken i Made a complaint at they Ford dealership but they denied they claim because they said something hit on they roof anda i'm sure that nothing hit
NHTSA ODI #11535695
Mileage unknown · Jul 21, 2023
Forward Collision Avoidance
Vehicle adaptive cruise control was set at 35mph in a 35mph speed zone as I approached a stop light I tapped the breaks which should have disengaged the cruise control but instead the vehicle speed accelerated. Warning light stated cruise control was disengaged with gray line through speed indicator. I stepped on the brakes hard…
Read full complaint
Vehicle adaptive cruise control was set at 35mph in a 35mph speed zone as I approached a stop light I tapped the breaks which should have disengaged the cruise control but instead the vehicle speed accelerated. Warning light stated cruise control was disengaged with gray line through speed indicator. I stepped on the brakes hard and the vehicle did stop and accelerator stopped. At no time was my foot on the accelerator pedal as well floor mats were not touching the pedal. Outside vehicle was clean and camera unobstructed. This just started after update 4.2.5.
NHTSA ODI #11533641
Mileage unknown · Jun 30, 2023
Forward Collision AvoidanceVehicle Speed Control
On 3 occasions in the past month I have been driving down the road and, without any action from me, cruise control has turned itself on, with a speed set above the speed limit. I noticed it because the car accelerated to reach the target speed (which was an unsafe speed). I immediately braked and turned off the cruise control.…
Read full complaint
On 3 occasions in the past month I have been driving down the road and, without any action from me, cruise control has turned itself on, with a speed set above the speed limit. I noticed it because the car accelerated to reach the target speed (which was an unsafe speed). I immediately braked and turned off the cruise control. The first two times it happened, I was pretty sure I had not accidentally activated cruise control by touching the button on the steering wheel. The third time, I was on a straight stretch of highway and was 100% sure I had done nothing to activate cruise control I had not used cruise control at any point from the time I turned on the car until the time this happened. I was between 10 and 15 minutes into my trip when this occurred.
NHTSA ODI #11529784
Mileage unknown · Jun 6, 2023
Electrical SystemFuel/propulsion System
After charging for the first time at a DC fast charge station to 80%, I resumed my trip and drove about 3 miles to merge onto the expressway, my screen panel said "safely stop now", with a turtle logo and battery icon coming on. my car then came to a complete stop within a few seconds in the middle of the on-ramp leaving me stra…
Read full complaint
After charging for the first time at a DC fast charge station to 80%, I resumed my trip and drove about 3 miles to merge onto the expressway, my screen panel said "safely stop now", with a turtle logo and battery icon coming on. my car then came to a complete stop within a few seconds in the middle of the on-ramp leaving me stranded. I repeatedly tried to turn the car on and off to see if i could get it to accelerate again but to no avail. I was stuck in the middle of the merge lane where my car would not move. After trying several attempts to rebooting, locking, turning off the car completely for 10-30 minutes, nothing worked. Although the accessory power said it was active there was no AC. After a couple of hours of waiting for a tow truck that would actually work with an EV, I locked the car again and tried to start. There were no warning lights so I tried to go to get off the expressway. After 3 miles at 70mph, the same warning lights came on and the car started to decelerate and then stopped. Luckily I was able to get over to the side of the interstate. After still waiting on tow truck for another 2 hours, lights inside the car started blinking, a loud banging sound started coming from the car and then nothing would work. Screens were black, doors were locked, windows wouldn’t roll up. No accessory power at all. It was 95° in Florida sun and I was completely stuck in the middle of nowhere at the mercy of any tow truck that would come help. It took 6 hours to get someone to come. He jumped the 12V battery and the car turned on and we loaded it onto the flatbed and took it to the dealership. Waiting now to see what is happening.
NHTSA ODI #11525550
Mileage unknown · May 31, 2023
Forward Collision AvoidanceVehicle Speed Control
On at least 8 occasions the car unintentionally shifted into cruise control and accelerated immediately. This usually happened while driving under 30 mph and rapidly accelerated to a much higher speed, sometimes set as high as 70 mph. On 3 occasions this happened in a parking lot and 2 occasions in a bank drive thru with a vehic…
Read full complaint
On at least 8 occasions the car unintentionally shifted into cruise control and accelerated immediately. This usually happened while driving under 30 mph and rapidly accelerated to a much higher speed, sometimes set as high as 70 mph. On 3 occasions this happened in a parking lot and 2 occasions in a bank drive thru with a vehicle only a few feet in front of me. Immediate emergency braking was required to avoid an accident with two very close calls within 1-3 feet of vehicle in front of me. This experience has been reported by numerous persons on the Mach E Forum (similarly complaining of near accidents) and the general conclusion is that the button that activates cruise control is both unnecessarily super sensitive and poorly located so that it is engaged by the lightest touch of your left palm, base of your left thumb, or another finger as you move it across the steering wheel. Please note that the form below does not allow for numerous occurrences.
NHTSA ODI #11524686
Mileage unknown · May 13, 2023
Electrical System
Car went into deep sleep mode after 12 volt battery malfunctioned. Car was completely disabled although it was fully charged. Ford dealership I took to had no knowledge of this ever happening, had no knowledge of vehicle having a 12 v battery, and claimed to of baver heard of any vehicle going into deep sleep mode.
NHTSA ODI #11521870
Official recalls
9Jun 30, 2026
Ford Motor Company (Ford) is recalling certain 2021-2023 Mustang Mach E vehicles. The rear differential pinion shaft may fracture.
Consequence & remedy
Consequence: Differential pinion shaft fracture may result in a loss of drive power, or unintended vehicle movement if the vehicle is in park without the parking brake applied, increasing the risk of a crash.
Remedy: Dealers will repair or replace the rear differential assembly as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed July 13, 2026. Additional letters will be sent once the remedy is available, anticipated in late December 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S50.
Jun 27, 2025
Ford Motor Company (Ford) is recalling certain 2022 Mustang Mach E vehicles equipped with an extended range battery. The high voltage battery main contactors may overheat.
Consequence & remedy
Consequence: An overheated high voltage battery contactor can result in a loss of drive power, increasing the risk of a crash.
Remedy: Dealers will replace the high voltage battery junction box, free of charge. Owner notification letters were mailed July 10, 2025. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 23S56. This recall is an expansion of previous NHTSA recall number 23V687.
Jun 13, 2025
Ford Motor Company (Ford) is recalling certain 2021-2025 Mustang Mach E vehicles. In the event of a low battery charge, the electronic door latches may remain locked once the driver or front passenger exits and shuts the door, possibly trapping someone who is unable to use the inside door release handles, such as a child in the back seat.
Consequence & remedy
Consequence: The inability to enter or exit the vehicle in an emergency increases the risk of injury.
Remedy: Dealers will update the Powertrain Control Module (PCM) and the Secondary On-Board Diagnostic Control Module C (SOBDMC) software, free of charge. Owner notification letters were mailed to 2021-2025 Mustang Mach-E owners September 12, 2025. Additionally, Owner notification letters were mailed to 2024-2025 Mustang Mach-E owners July 10, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S65.
Additional source detail variants (2)
Electrical System:body Control Module:software
Ford Motor Company (Ford) is recalling certain 2021-2025 Mustang Mach E vehicles. In the event of a low battery charge, the electronic door latches may remain locked once the driver or front passenger exits and shuts the door, possibly trapping someone who is unable to use the inside door release handles, such as a child in the back seat.
Consequence: The inability to enter or exit the vehicle in an emergency increases the risk of injury.
Remedy: Dealers will update the Powertrain Control Module (PCM) and the Secondary On-Board Diagnostic Control Module C (SOBDMC) software, free of charge. Owner notification letters were mailed to 2021-2025 Mustang Mach-E owners September 12, 2025. Additionally, Owner notification letters were mailed to 2024-2025 Mustang Mach-E owners July 10, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S65.
Latches/locks/linkages:doors:latch
Ford Motor Company (Ford) is recalling certain 2021-2025 Mustang Mach E vehicles. In the event of a low battery charge, the electronic door latches may remain locked once the driver or front passenger exits and shuts the door, possibly trapping someone who is unable to use the inside door release handles, such as a child in the back seat.
Consequence: The inability to enter or exit the vehicle in an emergency increases the risk of injury.
Remedy: Dealers will update the Powertrain Control Module (PCM) and the Secondary On-Board Diagnostic Control Module C (SOBDMC) software, free of charge. Owner notification letters were mailed to 2021-2025 Mustang Mach-E owners September 12, 2025. Additionally, Owner notification letters were mailed to 2024-2025 Mustang Mach-E owners July 10, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S65.
May 9, 2025
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to delay, freeze, or not display when the vehicle is in reverse.
Consequence & remedy
Consequence: A frozen or missing rearview camera image can reduce the driver's view behind the vehicle, increasing the risk of a crash.
Remedy: The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49.
Feb 28, 2025
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles previously repaired incorrectly under recall number 22V-412. The high voltage battery main contactors may overheat.
Consequence & remedy
Consequence: An overheated high voltage battery contactor may cause the vehicle to lose drive power, increasing the risk of a crash.
Remedy: Dealers will update the on-board software, free of charge. Owner notification letters were mailed April 11, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S14.
Oct 13, 2023
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles equipped with an extended range battery. The high voltage battery main contactors may overheat.
Consequence & remedy
Consequence: An overheated high voltage battery contactor can result in a loss of drive power, increasing the risk of a crash.
Remedy: Dealers will replace the high voltage battery junction box, free of charge. Owner notification letters were mailed December 29, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S56. Vehicles included in this recall that were previously repaired under recall 22V-412 will need to have the new remedy completed.
Aug 26, 2022
Ford Motor Company (Ford) is recalling certain 2022 Mustang Mach-E vehicles. The right-rear axle half shafts may have been manufactured improperly, allowing the half shaft stem to break under load.
Consequence & remedy
Consequence: A broken half shaft can cause a loss of drive power, or a rollaway could occur while parked if the electronic parking brake is not engaged. Either of these scenarios can increase the risk of a crash.
Remedy: Dealers will inspect the serial number, and replace the right-rear half shaft, as necessary, free of charge. Owner notification letters were mailed September 19, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S55.
Jun 10, 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles. The high voltage battery main contactors may overheat.
Consequence & remedy
Consequence: An overheated high voltage battery contactor may cause the vehicle to lose drive power, increasing the risk of a crash.
Remedy: Dealers will update the on-board software, free of charge. Owner notification letters were mailed on July 8, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S41.
Dec 16, 2021
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E and 2022 Maverick vehicles. The rear seat belt buckles may not be properly attached to the rear floor assembly. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 208, "Occupant Crash Protection," and 210, "Seat Belt Assembly Anchorages."
Consequence & remedy
Consequence: Improperly attached seat belts may not adequately restrain an occupant in a crash, increasing the risk of injury.
Remedy: Dealers will repair the rear seat belt buckle attachments, free of charge. Owner notification letters were mailed January 28, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C36.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4EA25001 · Collisions Involving Ford Bluecruise
Opened Jan 17, 2025 · No close date supplied
Status: open (inferred from source dates) · Electrical System:adas
On April 25, 2024, NHTSA’s Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24012) to assess BlueCruise, a partial driving automation system available on certain vehicles manufactured by Ford Motor Company (Ford). NHTSA opened the investigation after the agency received notice of two fatal collisions involving BlueCruise-equipped Ford Mustang Mach-E vehicles. Based on the incidents, NHTSA scoped the investigation to 2021-2024 Mustang Mach-E vehicles equipped with BlueCruise. In June 2024, ODI sent an Information Request (IR) letter to Ford requiring that it provide certain information pertaining to crashes, non-crash reports, and technical specifications that relate to BlueCruise, as well as other Ford partial driving automation systems that offer lane and speed maintenance. In its response to ODI’s IR, Ford stated that there are 2,539,962 Ford and Lincoln vehicles (including subject and peer vehicles) equipped with a partial driving automation system within the scope of the request. The majority of these vehicles are equipped with a system that Ford calls Lane Centering Assist (LCA), which is a hands-on partial driving automation system that combines longitudinal control authority governed by Adaptive Cruise Control (ACC) and lateral control authority governed by a steerable path. LCA is offered on a wide range of Ford and Lincoln models beginning in model year 2019. Vehicles that are equipped with BlueCruise, the focus of this investigation, have LCA capability and additionally offer hands-free partial driving automation when certain conditions are met. Hands-free BlueCruise operation is only offered on certain roadways and system availability is geofenced using vehicle GPS. BlueCruise-equipped vehicles employ a camera-based driver monitoring system to determine driver attentiveness to the roadway. BlueCruise was introduced in model year 2021 and is currently available in a select range of Ford and Lincoln vehicles. For BlueCruise- and LCA-equipped vehicles, both ACC and Pre-Collision Assist (PCA) features use a combination of camera and radar sensing technologies to detect and classify objects. ACC is specifically designed to detect vehicles (including cars, trucks, and motorcycles) and bicycles in front of the subject vehicle which are either stationary or moving in the same direction as the subject vehicle. Through this investigation, limitations in the detection of stationary vehicles in certain conditions have been identified. Specifically, due to the potential for false detection of stationary objects at long distances, Ford designed ACC to inhibit any response to reported stationary objects when the subject vehicle’s approach speed is at or above 62 mph. Additionally, system performance may be limited when there is poor visibility due to insufficient illumination. In addition to reviewing Ford’s response to ODI’s IR, the agency conducted a review of crash and non-crash reports identified collectively through Ford’s IR response, incident reporting through Standing General Order 2021-01 (SGO), and NHTSA vehicle owner questionnaires. In total, 32 crashes and 2,004 non-crash reports on subject and peer Ford vehicles were identified across manufacturer and ODI data sources. A detailed analysis of each crash was conducted including the review of any available police reports, photographs, data recovered from in-vehicle event data recorders, connected vehicle data, and/or other information. In both fatal collisions referenced in the PE24012 opening resume, the subject Ford Mustang Mach-E vehicle was traveling over 70 mph on a controlled-access highway during nighttime lighting conditions with hands-free BlueCruise engaged when it collided with a stationary vehicle. Analysis of data imaged from the vehicles’ event data recorders demonstrates that in each incident, the driver did not apply the brakes or take evasive steering action, and no deceleration was initiated by either the BlueCruise system or PCA prior to impact. Through the agency’s crash analysis, four additional frontal collisions were identified where the subject Ford impacted a stopped or slow-moving lead vehicle or another stationary object located in the travel lane. Two of these four incidents involved BlueCruise-equipped Ford Mustang Mach-E vehicles (included in the failure report summary along with the fatal collisions discussed above), while the other two involved other Ford models equipped with the LCA system. Additionally, a trend was identified through analysis of the non-crash reports relating to allegations that ACC (the longitudinal component of both BlueCruise and LCA) failed to detect and/or respond to a stopped or slow-moving lead vehicle. In these reports, consumers often describe that the absence of deceleration initiated by ACC was unexpected and required harsh manual braking or intervention from the PCA to avoid a frontal collision with the lead vehicle. Based on NHTSA’s analysis, system limitations relating to the detection of stationary vehicles while traveling at highway speeds and in nighttime lighting conditions appear to be factors in collisions under investigation and several apparently similar near-miss, non-crash reports. This Engineering Analysis (EA) is being opened to further investigate these system limitations and to evaluate drivers’ ability to respond to scenarios that exceed system limitations. During the EA, the agency expects to, among other things, perform vehicle evaluations, review additional technical information, and perform additional analysis of related crashes and non-crash reports. The crashes included in the failure report summary can be found at NHTSA.gov under the following SGO report identification numbers: 502-7268, 502-7426, 502-6852, 502-8738.
PE24012 · Collisions Involving Ford Bluecruise
Opened Apr 25, 2024 · Closed Jan 17, 2025
Status: closed (inferred from source dates) · Electrical System:adas
On April 25, 2024, NHTSA’s Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24012) to assess BlueCruise, a partial driving automation system available on certain vehicles manufactured by Ford Motor Company (Ford). NHTSA opened the investigation after the agency received notice of two fatal collisions involving BlueCruise-equipped Ford Mustang Mach-E vehicles. Based on the incidents, NHTSA scoped the investigation to 2021-2024 Mustang Mach-E vehicles equipped with BlueCruise. In June 2024, ODI sent an Information Request (IR) letter to Ford requiring that it provide certain information pertaining to crashes, non-crash reports, and technical specifications that relate to BlueCruise, as well as other Ford partial driving automation systems that offer lane and speed maintenance. In its response to ODI’s IR, Ford stated that there are 2,539,962 Ford and Lincoln vehicles (including subject and peer vehicles) equipped with a partial driving automation system within the scope of the request. The majority of these vehicles are equipped with a system that Ford calls Lane Centering Assist (LCA), which is a hands-on partial driving automation system that combines longitudinal control authority governed by Adaptive Cruise Control (ACC) and lateral control authority governed by a steerable path. LCA is offered on a wide range of Ford and Lincoln models beginning in model year 2019. Vehicles that are equipped with BlueCruise, the focus of this investigation, have LCA capability and additionally offer hands-free partial driving automation when certain conditions are met. Hands-free BlueCruise operation is only offered on certain roadways and system availability is geofenced using vehicle GPS. BlueCruise-equipped vehicles employ a camera-based driver monitoring system to determine driver attentiveness to the roadway. BlueCruise was introduced in model year 2021 and is currently available in a select range of Ford and Lincoln vehicles. For BlueCruise- and LCA-equipped vehicles, both ACC and Pre-Collision Assist (PCA) features use a combination of camera and radar sensing technologies to detect and classify objects. ACC is specifically designed to detect vehicles (including cars, trucks, and motorcycles) and bicycles in front of the subject vehicle which are either stationary or moving in the same direction as the subject vehicle. Through this investigation, limitations in the detection of stationary vehicles in certain conditions have been identified. Specifically, due to the potential for false detection of stationary objects at long distances, Ford designed ACC to inhibit any response to reported stationary objects when the subject vehicle’s approach speed is at or above 62 mph. Additionally, system performance may be limited when there is poor visibility due to insufficient illumination. In addition to reviewing Ford’s response to ODI’s IR, the agency conducted a review of crash and non-crash reports identified collectively through Ford’s IR response, incident reporting through Standing General Order 2021-01 (SGO), and NHTSA vehicle owner questionnaires. In total, 32 crashes and 2,004 non-crash reports on subject and peer Ford vehicles were identified across manufacturer and ODI data sources. A detailed analysis of each crash was conducted including the review of any available police reports, photographs, data recovered from in-vehicle event data recorders, connected vehicle data, and/or other information. In both fatal collisions referenced in the PE24012 opening resume, the subject Ford Mustang Mach-E vehicle was traveling over 70 mph on a controlled-access highway during nighttime lighting conditions with hands-free BlueCruise engaged when it collided with a stationary vehicle. Analysis of data imaged from the vehicles’ event data recorders demonstrates that in each incident, the driver did not apply the brakes or take evasive steering action, and no deceleration was initiated by either the BlueCruise system or PCA prior to impact. Through the agency’s crash analysis, four additional frontal collisions were identified where the subject Ford impacted a stopped or slow-moving lead vehicle or another stationary object located in the travel lane. Two of these four incidents involved BlueCruise-equipped Ford Mustang Mach-E vehicles (included in the failure report summary along with the fatal collisions discussed above), while the other two involved other Ford models equipped with the LCA system. Additionally, a trend was identified through analysis of the non-crash reports relating to allegations that ACC (the longitudinal component of both BlueCruise and LCA) failed to detect and/or respond to a stopped or slow-moving lead vehicle. In these reports, consumers often describe that the absence of deceleration initiated by ACC was unexpected and required harsh manual braking or intervention from the PCA to avoid a frontal collision with the lead vehicle. Based on NHTSA’s analysis, system limitations relating to the detection of stationary vehicles while traveling at highway speeds and in nighttime lighting conditions appear to be factors in collisions under investigation and several apparently similar near-miss, non-crash reports. This Preliminary Evaluation is being upgraded to an Engineering Analysis (EA25001) to further investigate these system limitations and to evaluate drivers’ ability to respond to scenarios that exceed system limitations. During the EA, the agency expects to, among other things, perform vehicle evaluations, review additional technical information, and perform additional analysis of related crashes and non-crash reports. The crashes included in the failure report summary can be found at NHTSA.gov under the following SGO report identification numbers: 502-7268, 502-7426, 502-6852, 502-8738.
RQ23004 · High Voltage Battery Contactor Failure
Opened Aug 17, 2023 · Closed Dec 6, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System:traction Battery:management System/energy Control Module (bms/becm):software; Engine And Engine Cooling:engine:engine Control Module (ecu/ecm):software
On August 17, 2023, the Office of Defects Investigations (ODI) opened RQ23-004 to investigate instances of loss of motor power due to overheating high voltage battery contactors in model year (MY) 2021-2022 Ford Mustang Mach-E vehicles (subject vehicles). This Recall Query (RQ) was opened after receiving 12 consumer complaints alleging a high voltage battery main contactor failure in subject vehicles that were included in Recall 22V-412 and remedied prior to the reported incidents. The remedy in 22V-412 was a Secondary On-Board Diagnostic Control Module (SOBDMC) software update to monitor contactor temperature and reduce battery power to prevent damage to the contactor, and a Battery Energy Control Module (BECM) software update to monitor contactor resistance to identify an overheated contactor and reduce vehicle power to prevent further damage. On October 13, 2023, Ford filed Recall 23V-687 of 34,762 2021-2022 Ford Mustang Mach-E vehicles produced from May 27, 2020 to May 24, 2022 with recalled Bussed Electrical Center parts NK48-10C666-AA, NK48-10C666-BA, or LK98-10C666-AB. Affected vehicles are equipped with the extended range battery. Ford stated that preexisting damage to the contactors caused by heat and accumulated wear may reduce the effectiveness of the software update remedy in 22V-412. The remedy of 23V-687 is to complete a replacement of the Bussed Electrical Center, or High Voltage Battery Junction Box. In addition, Ford stated that subject vehicles equipped with standard range batteries, in comparison to vehicles equipped with extended range batteries, are less at risk of experiencing this failure due to their smaller battery capacity and lower output electric drive motors. In view of the recall action taken by Ford, ODI is closing this investigation. ODI will continue to monitor reports of this failure in both extended range and standard range models. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Electrical System:propulsion System:traction Battery:management System/energy Control Module (bms/becm):software
On August 17, 2023, the Office of Defects Investigations (ODI) opened RQ23-004 to investigate instances of loss of motor power due to overheating high voltage battery contactors in model year (MY) 2021-2022 Ford Mustang Mach-E vehicles (subject vehicles). This Recall Query (RQ) was opened after receiving 12 consumer complaints alleging a high voltage battery main contactor failure in subject vehicles that were included in Recall 22V-412 and remedied prior to the reported incidents. The remedy in 22V-412 was a Secondary On-Board Diagnostic Control Module (SOBDMC) software update to monitor contactor temperature and reduce battery power to prevent damage to the contactor, and a Battery Energy Control Module (BECM) software update to monitor contactor resistance to identify an overheated contactor and reduce vehicle power to prevent further damage. On October 13, 2023, Ford filed Recall 23V-687 of 34,762 2021-2022 Ford Mustang Mach-E vehicles produced from May 27, 2020 to May 24, 2022 with recalled Bussed Electrical Center parts NK48-10C666-AA, NK48-10C666-BA, or LK98-10C666-AB. Affected vehicles are equipped with the extended range battery. Ford stated that preexisting damage to the contactors caused by heat and accumulated wear may reduce the effectiveness of the software update remedy in 22V-412. The remedy of 23V-687 is to complete a replacement of the Bussed Electrical Center, or High Voltage Battery Junction Box. In addition, Ford stated that subject vehicles equipped with standard range batteries, in comparison to vehicles equipped with extended range batteries, are less at risk of experiencing this failure due to their smaller battery capacity and lower output electric drive motors. In view of the recall action taken by Ford, ODI is closing this investigation. ODI will continue to monitor reports of this failure in both extended range and standard range models. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine And Engine Cooling:engine:engine Control Module (ecu/ecm):software
On August 17, 2023, the Office of Defects Investigations (ODI) opened RQ23-004 to investigate instances of loss of motor power due to overheating high voltage battery contactors in model year (MY) 2021-2022 Ford Mustang Mach-E vehicles (subject vehicles). This Recall Query (RQ) was opened after receiving 12 consumer complaints alleging a high voltage battery main contactor failure in subject vehicles that were included in Recall 22V-412 and remedied prior to the reported incidents. The remedy in 22V-412 was a Secondary On-Board Diagnostic Control Module (SOBDMC) software update to monitor contactor temperature and reduce battery power to prevent damage to the contactor, and a Battery Energy Control Module (BECM) software update to monitor contactor resistance to identify an overheated contactor and reduce vehicle power to prevent further damage. On October 13, 2023, Ford filed Recall 23V-687 of 34,762 2021-2022 Ford Mustang Mach-E vehicles produced from May 27, 2020 to May 24, 2022 with recalled Bussed Electrical Center parts NK48-10C666-AA, NK48-10C666-BA, or LK98-10C666-AB. Affected vehicles are equipped with the extended range battery. Ford stated that preexisting damage to the contactors caused by heat and accumulated wear may reduce the effectiveness of the software update remedy in 22V-412. The remedy of 23V-687 is to complete a replacement of the Bussed Electrical Center, or High Voltage Battery Junction Box. In addition, Ford stated that subject vehicles equipped with standard range batteries, in comparison to vehicles equipped with extended range batteries, are less at risk of experiencing this failure due to their smaller battery capacity and lower output electric drive motors. In view of the recall action taken by Ford, ODI is closing this investigation. ODI will continue to monitor reports of this failure in both extended range and standard range models. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
Illustration