NHTSA owner reports · September 18, 2026 snapshot.
Vehicle Speed Control complaints
18 reportsClear category filterMileage unknown · Jun 30, 2023
Forward Collision AvoidanceVehicle Speed Control
On 3 occasions in the past month I have been driving down the road and, without any action from me, cruise control has turned itself on, with a speed set above the speed limit. I noticed it because the car accelerated to reach the target speed (which was an unsafe speed). I immediately braked and turned off the cruise control.…
Read full complaint
On 3 occasions in the past month I have been driving down the road and, without any action from me, cruise control has turned itself on, with a speed set above the speed limit. I noticed it because the car accelerated to reach the target speed (which was an unsafe speed). I immediately braked and turned off the cruise control. The first two times it happened, I was pretty sure I had not accidentally activated cruise control by touching the button on the steering wheel. The third time, I was on a straight stretch of highway and was 100% sure I had done nothing to activate cruise control I had not used cruise control at any point from the time I turned on the car until the time this happened. I was between 10 and 15 minutes into my trip when this occurred.
NHTSA ODI #11529784
Mileage unknown · May 31, 2023
Forward Collision AvoidanceVehicle Speed Control
On at least 8 occasions the car unintentionally shifted into cruise control and accelerated immediately. This usually happened while driving under 30 mph and rapidly accelerated to a much higher speed, sometimes set as high as 70 mph. On 3 occasions this happened in a parking lot and 2 occasions in a bank drive thru with a vehic…
Read full complaint
On at least 8 occasions the car unintentionally shifted into cruise control and accelerated immediately. This usually happened while driving under 30 mph and rapidly accelerated to a much higher speed, sometimes set as high as 70 mph. On 3 occasions this happened in a parking lot and 2 occasions in a bank drive thru with a vehicle only a few feet in front of me. Immediate emergency braking was required to avoid an accident with two very close calls within 1-3 feet of vehicle in front of me. This experience has been reported by numerous persons on the Mach E Forum (similarly complaining of near accidents) and the general conclusion is that the button that activates cruise control is both unnecessarily super sensitive and poorly located so that it is engaged by the lightest touch of your left palm, base of your left thumb, or another finger as you move it across the steering wheel. Please note that the form below does not allow for numerous occurrences.
NHTSA ODI #11524686
Mileage unknown · Apr 20, 2023
Forward Collision AvoidanceVehicle Speed Control
The cruise control is activated by the slightest touch of the button. Running the heel of your hand over the button will activate it. The button acts like a screen touch rather than a button.
NHTSA ODI #11518037
Mileage unknown · Jan 13, 2023
Forward Collision AvoidanceVehicle Speed Control
I am randomly receiving the errors: "Front Camera Fault" "Pre-Collision Assist Not Available" Also, my cruise control no longer works while this error is active. Error will clear itself after a few minutes, but will still pop up from time to time.
NHTSA ODI #11501612
Mileage unknown · Sep 23, 2022
Electrical SystemEngineVehicle Speed Control
THE BATTERY ENERGY CONTROL MODULE RECALL SOFTWARE UPDATE WAS COMPLETED ON MY VEHICLE ON SEPTEMBER 22ND 2022 AT 1203 PM AT GOSCH FORD OF HEMET. UPON LEAVING AROUND A MILE DOWN THE ROAD I WAS DRIVING AROUND A CORNER. WHILE IN THIS CORNER MULTIPLE THINGS HAPPENED AT THE SAME EXACT MOMENT. MY TRACTION LIGHT MOMENTARILY FLASHED ALONG…
Read full complaint
THE BATTERY ENERGY CONTROL MODULE RECALL SOFTWARE UPDATE WAS COMPLETED ON MY VEHICLE ON SEPTEMBER 22ND 2022 AT 1203 PM AT GOSCH FORD OF HEMET. UPON LEAVING AROUND A MILE DOWN THE ROAD I WAS DRIVING AROUND A CORNER. WHILE IN THIS CORNER MULTIPLE THINGS HAPPENED AT THE SAME EXACT MOMENT. MY TRACTION LIGHT MOMENTARILY FLASHED ALONG WITH A SERVICE WRENCH. VEHICLE SKID PARTIALLY OFF-ROAD INTO THE DITCH. I LOST CONTROL FOR A BREIF MOMENT BUT WAS ABLE TO GAIN CONTROL BEFORE CRASHING. MY SPEED WAS DRASTICALLY REDUCED TO ABOUT 1/3 OF ITS NORMAL POWER. THE VEHICLE WOULD STILL DRIVE JUST MUCH SLOWER. UPON THIS HAPPENING I IMMEDIATELY TOOK MY VEHICLE BACK TO THE DEALERSHIP. THIS RECALL WAS VERY VAGUE. WHEN I WAS AT THE DEALERSHIP I INITIALLY ASKED THE FORD SERVICE SALESMAN DANIEL VENTURA IF THIS SOFTWARE CHANGED ANY ASPECT OF MY VEHICLES PERFORMANCE. HE THEN READ THE RECALL LETTER AND SAID IF IT DID IT NORMALLY WOULD SAY IT EITHER IN THE RECALL ITSELF OR THE LETTER FORD SENDS YOU THEY WOULD NORMALLYSAY IT IN IT. IT DID NOT MENTION THAT WHILE DRIVING THRU A CORNER IF YOU LOOSE POWER IN THE CAR DUE TO A BATTERY CONTROL MODULE FAILURE THAT YOU MAY LOOSE TRACTION AND LOOSE CONTROL OF THE CAR MOMENTARILY. THIS IS A VERY UNSAFE DRIVING CONDITION. FURTHERMORE WHEN I LEFT THE DEALERSHIP THE CAR DROVE DIFFERENTLY. IT SEEMED LIKE THE HORSE POWER WAS ABOUT 5-10 HP LESS THEN WHEN PURCHASED. IT FELT A LITTLE WEIRD TO GET USED TO DRIVING DOWN THE ROAD SINCE IT HAD A LITTLE BIT MORE PUSH THEN BEFORE. I MENTION THIS BECAUSE I BELIEVE THAT AS A CONSUMER I HAVE A RIGHT TO KNOW THE SOFTWARE THAT IS GOING INTO MY CAR. IF ANY ADVERSE REACTION THAT MAY CAUSE ME A DIFFERENT DRIVING EXPERIENCE OR PUT MY LIFE AT RISK OF CRASHING SHOULD HAVE BEEN INCLUDED IN THE SAFETY RECALL OR THE LETTER FORD HAD SENT US IN THE RECALL. I AM A FIRM BELIEVER THEY DO NOT WANT TO TELL US THAT THIS VEHICLE IS STILL NOT SAFE TO DRIVE AS WHAT HAPPENED TO ME HAVING THE BATTERY CONTROL MODULE FAILURE DURING CORNERING.
NHTSA ODI #11485995
7,500 miles · Sep 1, 2022
Power TrainVehicle Speed ControlCrash
The contact owns a 2022 Ford Mustang. The contact stated while pulling into a parking spot at approximately 2 MPH and had not yet placed the vehicle in park, the vehicle had an unintended acceleration. The contact stated no warning light was illuminated. The vehicle crashed into a light post, ran over the post, and crashed into …
Read full complaint
The contact owns a 2022 Ford Mustang. The contact stated while pulling into a parking spot at approximately 2 MPH and had not yet placed the vehicle in park, the vehicle had an unintended acceleration. The contact stated no warning light was illuminated. The vehicle crashed into a light post, ran over the post, and crashed into a back of a building. The vehicle had damage to the hood, grill and bumper and also to the undercarriage. The contact said he had not suffered any injuries. The police were on the scene and filed a report. The contact had the vehicle towed to a collision repair shop. The vehicle had not been diagnosed by a dealer or independent mechanic. The vehicle had not been repaired. The contact researched online and related the failure to NHTSA Campaign Number: 22V333000 (Vehicle Speed Control, Power Train). The manufacturer had been informed of the failure. The failure mileage was approximately 7,500.
NHTSA ODI #11482450
Mileage unknown · Aug 17, 2022
Vehicle Speed ControlCrash
Vehicle had an unintended acceleration resulting in crash in a parking lot.
NHTSA ODI #11479784
Mileage unknown · Aug 6, 2022
Electrical SystemUnknown Or OtherVehicle Speed Control
Adaptive cruise control fault, pre-commission sensors not working, anti-lock break fault, restraint fault, tire pressure fault, dash turns off while driving which makes unable to see speed driving.
NHTSA ODI #11477929
Official recalls
9Jun 30, 2026
Ford Motor Company (Ford) is recalling certain 2021-2023 Mustang Mach E vehicles. The rear differential pinion shaft may fracture.
Consequence & remedy
Consequence: Differential pinion shaft fracture may result in a loss of drive power, or unintended vehicle movement if the vehicle is in park without the parking brake applied, increasing the risk of a crash.
Remedy: Dealers will repair or replace the rear differential assembly as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed July 13, 2026. Additional letters will be sent once the remedy is available, anticipated in late December 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S50.
Jun 27, 2025
Ford Motor Company (Ford) is recalling certain 2022 Mustang Mach E vehicles equipped with an extended range battery. The high voltage battery main contactors may overheat.
Consequence & remedy
Consequence: An overheated high voltage battery contactor can result in a loss of drive power, increasing the risk of a crash.
Remedy: Dealers will replace the high voltage battery junction box, free of charge. Owner notification letters were mailed July 10, 2025. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 23S56. This recall is an expansion of previous NHTSA recall number 23V687.
Jun 13, 2025
Ford Motor Company (Ford) is recalling certain 2021-2025 Mustang Mach E vehicles. In the event of a low battery charge, the electronic door latches may remain locked once the driver or front passenger exits and shuts the door, possibly trapping someone who is unable to use the inside door release handles, such as a child in the back seat.
Consequence & remedy
Consequence: The inability to enter or exit the vehicle in an emergency increases the risk of injury.
Remedy: Dealers will update the Powertrain Control Module (PCM) and the Secondary On-Board Diagnostic Control Module C (SOBDMC) software, free of charge. Owner notification letters were mailed to 2021-2025 Mustang Mach-E owners September 12, 2025. Additionally, Owner notification letters were mailed to 2024-2025 Mustang Mach-E owners July 10, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S65.
Additional source detail variants (2)
Electrical System:body Control Module:software
Ford Motor Company (Ford) is recalling certain 2021-2025 Mustang Mach E vehicles. In the event of a low battery charge, the electronic door latches may remain locked once the driver or front passenger exits and shuts the door, possibly trapping someone who is unable to use the inside door release handles, such as a child in the back seat.
Consequence: The inability to enter or exit the vehicle in an emergency increases the risk of injury.
Remedy: Dealers will update the Powertrain Control Module (PCM) and the Secondary On-Board Diagnostic Control Module C (SOBDMC) software, free of charge. Owner notification letters were mailed to 2021-2025 Mustang Mach-E owners September 12, 2025. Additionally, Owner notification letters were mailed to 2024-2025 Mustang Mach-E owners July 10, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S65.
Latches/locks/linkages:doors:latch
Ford Motor Company (Ford) is recalling certain 2021-2025 Mustang Mach E vehicles. In the event of a low battery charge, the electronic door latches may remain locked once the driver or front passenger exits and shuts the door, possibly trapping someone who is unable to use the inside door release handles, such as a child in the back seat.
Consequence: The inability to enter or exit the vehicle in an emergency increases the risk of injury.
Remedy: Dealers will update the Powertrain Control Module (PCM) and the Secondary On-Board Diagnostic Control Module C (SOBDMC) software, free of charge. Owner notification letters were mailed to 2021-2025 Mustang Mach-E owners September 12, 2025. Additionally, Owner notification letters were mailed to 2024-2025 Mustang Mach-E owners July 10, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S65.
May 9, 2025
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to delay, freeze, or not display when the vehicle is in reverse.
Consequence & remedy
Consequence: A frozen or missing rearview camera image can reduce the driver's view behind the vehicle, increasing the risk of a crash.
Remedy: The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49.
Feb 28, 2025
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles previously repaired incorrectly under recall number 22V-412. The high voltage battery main contactors may overheat.
Consequence & remedy
Consequence: An overheated high voltage battery contactor may cause the vehicle to lose drive power, increasing the risk of a crash.
Remedy: Dealers will update the on-board software, free of charge. Owner notification letters were mailed April 11, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S14.
Oct 13, 2023
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles equipped with an extended range battery. The high voltage battery main contactors may overheat.
Consequence & remedy
Consequence: An overheated high voltage battery contactor can result in a loss of drive power, increasing the risk of a crash.
Remedy: Dealers will replace the high voltage battery junction box, free of charge. Owner notification letters were mailed December 29, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S56. Vehicles included in this recall that were previously repaired under recall 22V-412 will need to have the new remedy completed.
Aug 26, 2022
Ford Motor Company (Ford) is recalling certain 2022 Mustang Mach-E vehicles. The right-rear axle half shafts may have been manufactured improperly, allowing the half shaft stem to break under load.
Consequence & remedy
Consequence: A broken half shaft can cause a loss of drive power, or a rollaway could occur while parked if the electronic parking brake is not engaged. Either of these scenarios can increase the risk of a crash.
Remedy: Dealers will inspect the serial number, and replace the right-rear half shaft, as necessary, free of charge. Owner notification letters were mailed September 19, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S55.
Jun 10, 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles. The high voltage battery main contactors may overheat.
Consequence & remedy
Consequence: An overheated high voltage battery contactor may cause the vehicle to lose drive power, increasing the risk of a crash.
Remedy: Dealers will update the on-board software, free of charge. Owner notification letters were mailed on July 8, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S41.
Dec 16, 2021
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E and 2022 Maverick vehicles. The rear seat belt buckles may not be properly attached to the rear floor assembly. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 208, "Occupant Crash Protection," and 210, "Seat Belt Assembly Anchorages."
Consequence & remedy
Consequence: Improperly attached seat belts may not adequately restrain an occupant in a crash, increasing the risk of injury.
Remedy: Dealers will repair the rear seat belt buckle attachments, free of charge. Owner notification letters were mailed January 28, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C36.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4EA25001 · Collisions Involving Ford Bluecruise
Opened Jan 17, 2025 · No close date supplied
Status: open (inferred from source dates) · Electrical System:adas
On April 25, 2024, NHTSA’s Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24012) to assess BlueCruise, a partial driving automation system available on certain vehicles manufactured by Ford Motor Company (Ford). NHTSA opened the investigation after the agency received notice of two fatal collisions involving BlueCruise-equipped Ford Mustang Mach-E vehicles. Based on the incidents, NHTSA scoped the investigation to 2021-2024 Mustang Mach-E vehicles equipped with BlueCruise. In June 2024, ODI sent an Information Request (IR) letter to Ford requiring that it provide certain information pertaining to crashes, non-crash reports, and technical specifications that relate to BlueCruise, as well as other Ford partial driving automation systems that offer lane and speed maintenance. In its response to ODI’s IR, Ford stated that there are 2,539,962 Ford and Lincoln vehicles (including subject and peer vehicles) equipped with a partial driving automation system within the scope of the request. The majority of these vehicles are equipped with a system that Ford calls Lane Centering Assist (LCA), which is a hands-on partial driving automation system that combines longitudinal control authority governed by Adaptive Cruise Control (ACC) and lateral control authority governed by a steerable path. LCA is offered on a wide range of Ford and Lincoln models beginning in model year 2019. Vehicles that are equipped with BlueCruise, the focus of this investigation, have LCA capability and additionally offer hands-free partial driving automation when certain conditions are met. Hands-free BlueCruise operation is only offered on certain roadways and system availability is geofenced using vehicle GPS. BlueCruise-equipped vehicles employ a camera-based driver monitoring system to determine driver attentiveness to the roadway. BlueCruise was introduced in model year 2021 and is currently available in a select range of Ford and Lincoln vehicles. For BlueCruise- and LCA-equipped vehicles, both ACC and Pre-Collision Assist (PCA) features use a combination of camera and radar sensing technologies to detect and classify objects. ACC is specifically designed to detect vehicles (including cars, trucks, and motorcycles) and bicycles in front of the subject vehicle which are either stationary or moving in the same direction as the subject vehicle. Through this investigation, limitations in the detection of stationary vehicles in certain conditions have been identified. Specifically, due to the potential for false detection of stationary objects at long distances, Ford designed ACC to inhibit any response to reported stationary objects when the subject vehicle’s approach speed is at or above 62 mph. Additionally, system performance may be limited when there is poor visibility due to insufficient illumination. In addition to reviewing Ford’s response to ODI’s IR, the agency conducted a review of crash and non-crash reports identified collectively through Ford’s IR response, incident reporting through Standing General Order 2021-01 (SGO), and NHTSA vehicle owner questionnaires. In total, 32 crashes and 2,004 non-crash reports on subject and peer Ford vehicles were identified across manufacturer and ODI data sources. A detailed analysis of each crash was conducted including the review of any available police reports, photographs, data recovered from in-vehicle event data recorders, connected vehicle data, and/or other information. In both fatal collisions referenced in the PE24012 opening resume, the subject Ford Mustang Mach-E vehicle was traveling over 70 mph on a controlled-access highway during nighttime lighting conditions with hands-free BlueCruise engaged when it collided with a stationary vehicle. Analysis of data imaged from the vehicles’ event data recorders demonstrates that in each incident, the driver did not apply the brakes or take evasive steering action, and no deceleration was initiated by either the BlueCruise system or PCA prior to impact. Through the agency’s crash analysis, four additional frontal collisions were identified where the subject Ford impacted a stopped or slow-moving lead vehicle or another stationary object located in the travel lane. Two of these four incidents involved BlueCruise-equipped Ford Mustang Mach-E vehicles (included in the failure report summary along with the fatal collisions discussed above), while the other two involved other Ford models equipped with the LCA system. Additionally, a trend was identified through analysis of the non-crash reports relating to allegations that ACC (the longitudinal component of both BlueCruise and LCA) failed to detect and/or respond to a stopped or slow-moving lead vehicle. In these reports, consumers often describe that the absence of deceleration initiated by ACC was unexpected and required harsh manual braking or intervention from the PCA to avoid a frontal collision with the lead vehicle. Based on NHTSA’s analysis, system limitations relating to the detection of stationary vehicles while traveling at highway speeds and in nighttime lighting conditions appear to be factors in collisions under investigation and several apparently similar near-miss, non-crash reports. This Engineering Analysis (EA) is being opened to further investigate these system limitations and to evaluate drivers’ ability to respond to scenarios that exceed system limitations. During the EA, the agency expects to, among other things, perform vehicle evaluations, review additional technical information, and perform additional analysis of related crashes and non-crash reports. The crashes included in the failure report summary can be found at NHTSA.gov under the following SGO report identification numbers: 502-7268, 502-7426, 502-6852, 502-8738.
PE24012 · Collisions Involving Ford Bluecruise
Opened Apr 25, 2024 · Closed Jan 17, 2025
Status: closed (inferred from source dates) · Electrical System:adas
On April 25, 2024, NHTSA’s Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24012) to assess BlueCruise, a partial driving automation system available on certain vehicles manufactured by Ford Motor Company (Ford). NHTSA opened the investigation after the agency received notice of two fatal collisions involving BlueCruise-equipped Ford Mustang Mach-E vehicles. Based on the incidents, NHTSA scoped the investigation to 2021-2024 Mustang Mach-E vehicles equipped with BlueCruise. In June 2024, ODI sent an Information Request (IR) letter to Ford requiring that it provide certain information pertaining to crashes, non-crash reports, and technical specifications that relate to BlueCruise, as well as other Ford partial driving automation systems that offer lane and speed maintenance. In its response to ODI’s IR, Ford stated that there are 2,539,962 Ford and Lincoln vehicles (including subject and peer vehicles) equipped with a partial driving automation system within the scope of the request. The majority of these vehicles are equipped with a system that Ford calls Lane Centering Assist (LCA), which is a hands-on partial driving automation system that combines longitudinal control authority governed by Adaptive Cruise Control (ACC) and lateral control authority governed by a steerable path. LCA is offered on a wide range of Ford and Lincoln models beginning in model year 2019. Vehicles that are equipped with BlueCruise, the focus of this investigation, have LCA capability and additionally offer hands-free partial driving automation when certain conditions are met. Hands-free BlueCruise operation is only offered on certain roadways and system availability is geofenced using vehicle GPS. BlueCruise-equipped vehicles employ a camera-based driver monitoring system to determine driver attentiveness to the roadway. BlueCruise was introduced in model year 2021 and is currently available in a select range of Ford and Lincoln vehicles. For BlueCruise- and LCA-equipped vehicles, both ACC and Pre-Collision Assist (PCA) features use a combination of camera and radar sensing technologies to detect and classify objects. ACC is specifically designed to detect vehicles (including cars, trucks, and motorcycles) and bicycles in front of the subject vehicle which are either stationary or moving in the same direction as the subject vehicle. Through this investigation, limitations in the detection of stationary vehicles in certain conditions have been identified. Specifically, due to the potential for false detection of stationary objects at long distances, Ford designed ACC to inhibit any response to reported stationary objects when the subject vehicle’s approach speed is at or above 62 mph. Additionally, system performance may be limited when there is poor visibility due to insufficient illumination. In addition to reviewing Ford’s response to ODI’s IR, the agency conducted a review of crash and non-crash reports identified collectively through Ford’s IR response, incident reporting through Standing General Order 2021-01 (SGO), and NHTSA vehicle owner questionnaires. In total, 32 crashes and 2,004 non-crash reports on subject and peer Ford vehicles were identified across manufacturer and ODI data sources. A detailed analysis of each crash was conducted including the review of any available police reports, photographs, data recovered from in-vehicle event data recorders, connected vehicle data, and/or other information. In both fatal collisions referenced in the PE24012 opening resume, the subject Ford Mustang Mach-E vehicle was traveling over 70 mph on a controlled-access highway during nighttime lighting conditions with hands-free BlueCruise engaged when it collided with a stationary vehicle. Analysis of data imaged from the vehicles’ event data recorders demonstrates that in each incident, the driver did not apply the brakes or take evasive steering action, and no deceleration was initiated by either the BlueCruise system or PCA prior to impact. Through the agency’s crash analysis, four additional frontal collisions were identified where the subject Ford impacted a stopped or slow-moving lead vehicle or another stationary object located in the travel lane. Two of these four incidents involved BlueCruise-equipped Ford Mustang Mach-E vehicles (included in the failure report summary along with the fatal collisions discussed above), while the other two involved other Ford models equipped with the LCA system. Additionally, a trend was identified through analysis of the non-crash reports relating to allegations that ACC (the longitudinal component of both BlueCruise and LCA) failed to detect and/or respond to a stopped or slow-moving lead vehicle. In these reports, consumers often describe that the absence of deceleration initiated by ACC was unexpected and required harsh manual braking or intervention from the PCA to avoid a frontal collision with the lead vehicle. Based on NHTSA’s analysis, system limitations relating to the detection of stationary vehicles while traveling at highway speeds and in nighttime lighting conditions appear to be factors in collisions under investigation and several apparently similar near-miss, non-crash reports. This Preliminary Evaluation is being upgraded to an Engineering Analysis (EA25001) to further investigate these system limitations and to evaluate drivers’ ability to respond to scenarios that exceed system limitations. During the EA, the agency expects to, among other things, perform vehicle evaluations, review additional technical information, and perform additional analysis of related crashes and non-crash reports. The crashes included in the failure report summary can be found at NHTSA.gov under the following SGO report identification numbers: 502-7268, 502-7426, 502-6852, 502-8738.
RQ23004 · High Voltage Battery Contactor Failure
Opened Aug 17, 2023 · Closed Dec 6, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System:traction Battery:management System/energy Control Module (bms/becm):software; Engine And Engine Cooling:engine:engine Control Module (ecu/ecm):software
On August 17, 2023, the Office of Defects Investigations (ODI) opened RQ23-004 to investigate instances of loss of motor power due to overheating high voltage battery contactors in model year (MY) 2021-2022 Ford Mustang Mach-E vehicles (subject vehicles). This Recall Query (RQ) was opened after receiving 12 consumer complaints alleging a high voltage battery main contactor failure in subject vehicles that were included in Recall 22V-412 and remedied prior to the reported incidents. The remedy in 22V-412 was a Secondary On-Board Diagnostic Control Module (SOBDMC) software update to monitor contactor temperature and reduce battery power to prevent damage to the contactor, and a Battery Energy Control Module (BECM) software update to monitor contactor resistance to identify an overheated contactor and reduce vehicle power to prevent further damage. On October 13, 2023, Ford filed Recall 23V-687 of 34,762 2021-2022 Ford Mustang Mach-E vehicles produced from May 27, 2020 to May 24, 2022 with recalled Bussed Electrical Center parts NK48-10C666-AA, NK48-10C666-BA, or LK98-10C666-AB. Affected vehicles are equipped with the extended range battery. Ford stated that preexisting damage to the contactors caused by heat and accumulated wear may reduce the effectiveness of the software update remedy in 22V-412. The remedy of 23V-687 is to complete a replacement of the Bussed Electrical Center, or High Voltage Battery Junction Box. In addition, Ford stated that subject vehicles equipped with standard range batteries, in comparison to vehicles equipped with extended range batteries, are less at risk of experiencing this failure due to their smaller battery capacity and lower output electric drive motors. In view of the recall action taken by Ford, ODI is closing this investigation. ODI will continue to monitor reports of this failure in both extended range and standard range models. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Electrical System:propulsion System:traction Battery:management System/energy Control Module (bms/becm):software
On August 17, 2023, the Office of Defects Investigations (ODI) opened RQ23-004 to investigate instances of loss of motor power due to overheating high voltage battery contactors in model year (MY) 2021-2022 Ford Mustang Mach-E vehicles (subject vehicles). This Recall Query (RQ) was opened after receiving 12 consumer complaints alleging a high voltage battery main contactor failure in subject vehicles that were included in Recall 22V-412 and remedied prior to the reported incidents. The remedy in 22V-412 was a Secondary On-Board Diagnostic Control Module (SOBDMC) software update to monitor contactor temperature and reduce battery power to prevent damage to the contactor, and a Battery Energy Control Module (BECM) software update to monitor contactor resistance to identify an overheated contactor and reduce vehicle power to prevent further damage. On October 13, 2023, Ford filed Recall 23V-687 of 34,762 2021-2022 Ford Mustang Mach-E vehicles produced from May 27, 2020 to May 24, 2022 with recalled Bussed Electrical Center parts NK48-10C666-AA, NK48-10C666-BA, or LK98-10C666-AB. Affected vehicles are equipped with the extended range battery. Ford stated that preexisting damage to the contactors caused by heat and accumulated wear may reduce the effectiveness of the software update remedy in 22V-412. The remedy of 23V-687 is to complete a replacement of the Bussed Electrical Center, or High Voltage Battery Junction Box. In addition, Ford stated that subject vehicles equipped with standard range batteries, in comparison to vehicles equipped with extended range batteries, are less at risk of experiencing this failure due to their smaller battery capacity and lower output electric drive motors. In view of the recall action taken by Ford, ODI is closing this investigation. ODI will continue to monitor reports of this failure in both extended range and standard range models. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine And Engine Cooling:engine:engine Control Module (ecu/ecm):software
On August 17, 2023, the Office of Defects Investigations (ODI) opened RQ23-004 to investigate instances of loss of motor power due to overheating high voltage battery contactors in model year (MY) 2021-2022 Ford Mustang Mach-E vehicles (subject vehicles). This Recall Query (RQ) was opened after receiving 12 consumer complaints alleging a high voltage battery main contactor failure in subject vehicles that were included in Recall 22V-412 and remedied prior to the reported incidents. The remedy in 22V-412 was a Secondary On-Board Diagnostic Control Module (SOBDMC) software update to monitor contactor temperature and reduce battery power to prevent damage to the contactor, and a Battery Energy Control Module (BECM) software update to monitor contactor resistance to identify an overheated contactor and reduce vehicle power to prevent further damage. On October 13, 2023, Ford filed Recall 23V-687 of 34,762 2021-2022 Ford Mustang Mach-E vehicles produced from May 27, 2020 to May 24, 2022 with recalled Bussed Electrical Center parts NK48-10C666-AA, NK48-10C666-BA, or LK98-10C666-AB. Affected vehicles are equipped with the extended range battery. Ford stated that preexisting damage to the contactors caused by heat and accumulated wear may reduce the effectiveness of the software update remedy in 22V-412. The remedy of 23V-687 is to complete a replacement of the Bussed Electrical Center, or High Voltage Battery Junction Box. In addition, Ford stated that subject vehicles equipped with standard range batteries, in comparison to vehicles equipped with extended range batteries, are less at risk of experiencing this failure due to their smaller battery capacity and lower output electric drive motors. In view of the recall action taken by Ford, ODI is closing this investigation. ODI will continue to monitor reports of this failure in both extended range and standard range models. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
Illustration